Next Article in Journal
Incorporating a Wheeled Vehicle Model in a New Monocular Visual Odometry Algorithm for Dynamic Outdoor Environments
Next Article in Special Issue
Doppler-Based Flow Rate Sensing in Microfluidic Channels
Previous Article in Journal
White Blood Cell Segmentation by Color-Space-Based K-Means Clustering
Previous Article in Special Issue
Recent Developments in Optical Detection Technologies in Lab-on-a-Chip Devices for Biosensing Applications
 
 
Font Type:
Arial Georgia Verdana
Font Size:
Aa Aa Aa
Line Spacing:
Column Width:
Background:
Article

Optimization of an Optical Inspection System Based on the Taguchi Method for Quantitative Analysis of Point-of-Care Testing

1
Department of Engineering Science, National Cheng Kung University, Tainan 701, Taiwan
2
Firstep Bioresearch, Incorporation, Tainan 701, Taiwan
*
Author to whom correspondence should be addressed.
Sensors 2014, 14(9), 16148-16158; https://doi.org/10.3390/s140916148
Submission received: 17 July 2014 / Revised: 18 August 2014 / Accepted: 25 August 2014 / Published: 1 September 2014
(This article belongs to the Special Issue Opto-Microfluidics for Bio Applications)

Abstract

: This study presents an optical inspection system for detecting a commercial point-of-care testing product and a new detection model covering from qualitative to quantitative analysis. Human chorionic gonadotropin (hCG) strips (cut-off value of the hCG commercial product is 25 mIU/mL) were the detection target in our study. We used a complementary metal-oxide semiconductor (CMOS) sensor to detect the colors of the test line and control line in the specific strips and to reduce the observation errors by the naked eye. To achieve better linearity between the grayscale and the concentration, and to decrease the standard deviation (increase the signal to noise ratio, S/N), the Taguchi method was used to find the optimal parameters for the optical inspection system. The pregnancy test used the principles of the lateral flow immunoassay, and the colors of the test and control line were caused by the gold nanoparticles. Because of the sandwich immunoassay model, the color of the gold nanoparticles in the test line was darkened by increasing the hCG concentration. As the results reveal, the S/N increased from 43.48 dB to 53.38 dB, and the hCG concentration detection increased from 6.25 to 50 mIU/mL with a standard deviation of less than 10%. With the optimal parameters to decrease the detection limit and to increase the linearity determined by the Taguchi method, the optical inspection system can be applied to various commercial rapid tests for the detection of ketamine, troponin I, and fatty acid binding protein (FABP).

1. Introduction

Human chorionic gonadotropin (hCG) is an important marker indicating pregnancy. In molecular biology, hCG is a hormone produced by the syncytiotrophoblast, a component of the fertilized egg after conception. In the early detection method, a bioassay method involving the germination of wheat by the pregnant woman's urine, or the ovulation of mice and frogs caused by implanting the pregnant woman's urine [1] was used to determine whether a woman was pregnant. In 1960, the radioimmunoassay (RIA) method was used to detect the hCG concentration [2].

In general, commercial detection reagents (hCG, ketamine, troponin I, luteinizing hormone, etc.) were used in the lateral flow immunoassay to detect the specific antigen, and the different color in the test line was observed by the naked eye. The pregnancy test strip was used to detect the hCG concentration in the woman's urine. The cut-off value of the pregnancy test strip was set to 25 mIU/mL. Because the pregnancy test strip was based on the immune-colloidal gold technique and the sandwich immunoassay, the color of the test line darkened when the levels of hCG concentration increased [3]. Lateral flow immunoassay had the advantages of simple operation, low cost, and rapid detection. However, the color of test line was lighter under lower levels of hCG concentration. The results of the test line were compared with the standard chroma card [46]. The color difference between the test line and standard chroma card was not clearly determined at lower levels by the naked eye, and the color discrimination was affected by the external environment and human factors.

Many studies have used optical sensors to capture images of the reaction area and applied image processing to quantitative analysis. In 2002, Zhang et al. used a charge-couple device (CCD) and digital signal processing (DSP) to perform mathematical calculations for RGB color models [7]. In 2005, Zhou et al. developed auto-control white balance algorithms for digital cameras [8]. In 2010, Zheng et al. applied image processing to biomedical detection [9]. The image capture system included a metal-oxide-semiconductor (CMOS), an enlarger lens, and a light-emitting diode (LED), and used the field programmable gate array (FPGA) and DSP to control the image capture and to perform image processing. In 2011, Jiang et al. utilized fuzzy theory to establish an algorithm for concentration classification [10]. Our optical inspection system used the CMOS sensor to capture the image of the reaction area (test line and control line) on the pregnancy test strip and then used grayscale processing of the test line to do quantitative analysis.

The purpose of our study was to develop a new optical inspection system to upgrade the detection method of the universal test strip from the conventional qualitative analysis to quantitative analysis. For quantitative analysis, a standard calibration curve of high linearity and low standard deviation at specific levels of concentration must be established. The Taguchi method is a statistical way to improve the quality of product performance and is also applied to engineering [1115], biotechnology [16], marking and advertising [1721]. Rosa et al. used the Taguchi method to improve the electrolytic conditions and increased the electroforming efficiency to 95% [22]. Rao et al. optimized the stirring conditions and inoculum dose for xylitol production, and the productivity was increased to 78.9% [23]. The CMOS sensor in our optical inspection system had ten parameters that affect the quality of the captured image, such as the black light compensation, brightness, contrast, exposure, gain, gamma, hue, saturation, sharpness value, and white balance. To increase the S/N value and to obtain a linear slope, we used the Taguchi method to find the optimal parameters for the optical inspection machine. After the optimal parameters were found, the optical inspection system can obtain a higher S/N value, lower standard deviation, more linear calibration curve (R square close to one), and a lower concentration detection limit.

2. Materials and Methods

2.1. Experimental Principles

The pregnancy test used a lateral flow sandwich immunoassay, and the pregnancy test strip included the backing card, sample pad, glass fiber, nitrocellulose membrane, and absorption pad. The anti-hCG antibody and immunoglobulin G antibody defined as the test line and control line were immobilized on the nitrocellulose membrane. The anti-hCG antibody-colloidal gold conjugates were immobilized on the glass fiber, which was defined as the mixture area. After the sample solution including the hCG antigen in the urine was dropped into the sample pad, the hCG antigen first bonded with the anti-hCG antibody-colloidal gold conjugates and then bonded with the anti-hCG antibody, as shown in Figure 1.

When the hCG concentration was increased, larger volumes of the colloid gold were aggregated in the test line and this deepens the color of the test line. Then, the optical inspection system was used to detect the color signals of the various hCG concentrations in the pregnancy test strip, and the laboratory virtual instrumentation engineering workbench (LABVIEW™) was used to control the CMOS sensor and analyze the image of the test line and control line. The CMOS sensor was a two-million-pixel camera module and supported image capture and video streaming. The CMOS sensor has the advantages of easy operation (USB 2.0), small dimensions (6 × 0.8 × 0.4 cm), and low power (input voltage 5 V). Under the grayscale analysis, the relationship between the hCG concentration and grayscale was established and the detection method of pregnancy test strip was converted from qualitative to quantitative analysis. To increase the linearity and decrease the standard deviation, we used the Taguchi method to find the suitable parameters for the CMOS sensor.

2.2. Design and Fabrication of the Optical Inspection Machine

The optical inspection machine, which included a CMOS sensor carrier, a set of LED lights, and a test strip carrier, was designed using AutoCAD®2010 software. The dimension of the optical inspection machine was 18 × 18 × 23 cm, the CMOS sensor carrier was 14 × 15 × 18 cm, and the test strip carrier was 12 × 7 × 1.2 cm. First, the case of the optical inspection machine was designed in a darkroom to protect the CMOS sensor from external light. Second, the CMOS sensor was fastened to the CMOS sensor carrier in the specific position to capture the clear image of the reaction region. Finally, the test strip carrier was used to confirm the reaction region of the test strip with the captured image of the CMOS sensor. The fabrication of the every pattern was constructed on a conventional polymethyl methacrylate (PMMA) substrate with a laser micromachining process by a CO2 laser machine (LaserPro Venus, GCC, New Taipei City, Taiwan).

2.3. Experimental Procedure

The model of the pregnancy test strip was a sandwich immunoassay. When the hCG concentration was increased, the color of the test line darkened. For quantitative analysis and error reduction, the optical inspection system was used to measure the color signals of the test line, as shown in Figure 2. First, to establish the optimal parameters for the optical inspection system under the lower hCG concentration conditions, we adjusted the grayscale of the standard color level from 255 to 247 to be the test line, and then the colors of the test and control line were calculated as grayscale signals, as shown in Figure 3. Second, after the best parameters were found, urine samples with various hCG concentrations (50, 37.5, 35, 12.5, and 6.25 mIU/mL) were injected into the pregnancy test strip to establish the standard calibration curve. The urine samples were prepared by the high hCG concentration (1000 mIU/mL) and blank urine purchased from Firstep Bioresearch Inc. (Tainan, Taiwan) and stored at 4 °C.

To obtain the best performance of the optical inspection system, we introduced the Taguchi method in a ten factor, two-level, L12 (211) orthogonal array to evaluate the related optimal values. Ten typically influential parameters included the black light compensation (control factor A), brightness (control factor B), contrast (control factor C), exposure (control factor D), gain (control factor E), gamma (control factor F), hue (control factor G), saturation (control factor H), sharpness value (control factor I), and white balance (control factor J). Table 1 presents the studied control factors with two levels. The grayscale was proportion to hCG concentration. The relationship between the hCG concentration and grayscale was illustrated by the straight line, and we used the dynamic quality characteristic. The S/N function was:

S / N = - 10 log ( S d 2 β 2 )
where β is linear slope, Sd is standard deviation. The S/N was used as a larger-the-better quality characteristic. The linear slope (β) was between the measured grayscale and standard grayscale, and the ideal slope was close to one. The standard grayscales were 247, 249, 251, 253, and 255. After the optimal parameters were found, the different hCG concentrations were used to detect the limit and create a higher linear curve between the grayscale and hCG concentration with the smaller standard deviation. Finally, the optical inspection system used the specific hCG concentration to detect the grayscale and utilized the linear curve to transform the hCG concentration.

3. Results and Discussion

3.1. The Taguchi Approach

After the experiments were designed by the Taguchi method (L12 (211) orthogonal array), the best levels for the factors could be determined through calculation and tabulation. Table 2 presents the influences of the control factors on the S/N function. When the control factor A transformed from level 1 to level 2, the S/N value increased from 41.74 to 44.89, and then the maximum effect of the control factor A was 3.15 dB. When the gap between the two levels of the control factor was wider, this control factor could affect the S/N value, and the control factor with higher level of S/N value was the optimal parameter. According to the S/N response graph (Figure 4), the recommended optimal levels of the control factors based on the larger-the-better S/N function were A2, B1, C1, D2, E1, F1, G1, H2, I2, J2.

In Table 2, the control factors A, F, and I had response greater than 3 dB, and these control factors (A, F, and I) affected the linearity of the dynamic results and standard deviation. To verify the optimal parameters and to eliminate the experimental errors with those control factors, we used the analysis of variance (ANOVA) to find the real control factor. In the ANOVA, when the confidence level of control factor was higher than 95%, this control factor has enough influence on the S/N value. The results reveal that the confidence levels of the control factors A, F, and I were higher than 95%, so these control factors could affect the S/N value. We only adjusted the control factor A, F, and I to optimal condition. The original levels of the control factors before the Taguchi method were A1, B1, C1, D1, E1, F1, G1, H1, I1, J1. According to the S/N response graph and ANOVA, the optimal levels of the control factors based on the larger-the-better S/N function were A2, B1, C1, D1, E1, F1, G1, H1, I2, J1.

We used the original and the optimal parameters to repeat confirmation experiments five times. The S/N ratios were based on Equation (1). After the confirmation experiments for both the original and the optimal parameters, the S/N value increased from the original experiment (43.48 dB) to the optimal experimental value (50.5 dB), which represented an increase of 7.02 dB. Moreover, when the original conditions were changed to the optimal conditions, the linear slope (β) between the measured grayscale and standard grayscale decreased from 1.0037 to 1.0004, and the standard deviation decreased from 0.0063 to 0.0035 (data not shown). The decreases indicated that the optimal parameters for the optical inspection machine had better linear slope and lower standard deviation.

According to the previous experiments, control factors A, F, and I had the major effects on the S/N value. Then, the interaction relationships between the A×F, A×I, and F×I were studied. First, we finished the interaction graph of interaction A×F, A×I, and F×I, as shown in Figure 5a–c. The results of these interactions reveal that A×F and F×I had no interaction, and the maximum of S/N value occurred at A2×F1 and F1×I1. However, a strong interaction was observed between control factor A and control factor I, and we found that when the control factor A was under the level 1 and level 2, the S/N value was increased by increasing the control factor I from level 1 (sharpness value 2) to level 2 (sharpness value 3). To obtain better S/N value, we finished the second interaction graph of the A×I interaction. The level 1 and level 2 of the control factor A were TRUE and FALSE, and the level 1 and level 2 of the control factor I were sharpness value 3 and sharpness value 7. The results reveal that the interaction A×I had a strong effect (same as that of the first interaction experiment). When the control factor A was changed from level 1 to level 2, the S/N value increased from 49.91 dB to 53.38 dB with the increasing sharpness value from 3 to 7, as shown in Figure 5d. Therefore, the optimal parameters of the optical inspection system were: A2, B1, C1, D1, E1, F1, G1, H1, I2, J1. After the confirmation experiment for the original and second optimal parameters, the S/N of second optimal experimental parameters increased 9.9 dB (from 43.48 dB to 53.38 dB).

3.2. The hCG Concentration Test by the Optical Inspection System

After using the Taguchi method to find the optimal parameters for the optical inspection system, we used urine samples with different hCG concentrations (50, 37.5, 25, 12.5, and 6.25 mIU/mL) to establish the hCG standard calibration curve and to detect the hCG concentration limit. In the conventional qualitative detection for the hCG strips, the cut-off value was 25 mIU/mL. When the hCG concentration ranged from 6.25 to 50 mIU/mL, the calibration curve between the grayscale and hCG concentration had high linearity (R square was 0.99), and the standard deviation of every hCG concentration was less than 10%, as shown in Figure 6. Moreover, the hCG concentration detection limit was reduced to 6.25 mIU/mL by using the optical inspection system. The commercial product of the pregnancy test strip was only determined at a cut-off value of 25 mIU/mL by the naked eye, so we have successfully established the hCG standard calibration curve and improved the conventional detection method from qualitative detection to quantitative detection. Finally, we used urine samples with five standard hCG concentrations (50, 37.5, 25, 12.5, and 6.25 mIU/mL) to proceed with the hCG strip detection by the optical inspection system. After the grayscale signals were transformed to hCG concentration by the calibration curve, each concentration error was less than 10%. Therefore, the optical inspection system can detect the unknown hCG concentration in the strip using the calibration curve.

4. Conclusions

We have successfully demonstrated the optimization of an optical inspection system for hCG concentration detection by using the Taguchi method. The results reveal that S/N value increased to 53.38 dB, and the linear slope was close to that obtained using the optimal parameters. The optical inspection system established a highly linear calibration curve for hCG concentration, and the detection error of the hCG concentration was less than 10%. The conventional qualitative detection method for any test strip was upgraded to quantitative detection, and the detection limit of specific concentration was below the traditional cut-off value. In the future, the newly optical inspection system could be applied to other clinical strip detection and color tests.

Acknowledgments

This research was supported by the Southern Taiwan Science Park (STSP), Taiwan, under contract 102CB01 and 103CB04. Partial funding from the Ministry of Science Technology, Taiwan, under grants NSC 102-2811-E-006-040- and 103-2811-E-006-016- is gratefully acknowledged. This technology has been successfully transferred to Firstep Bioresearch Inc. to develop and manufacture the EZQuick reader series.

Author Contributions

Yu-Cheng Lin coordinated the project. Chia-Hsien Yeh and Zi-Qi Zhao designed the experiment methods and developed the optical inspection system. Pi-Lan Shen contributed reagents, materials, and market analysis. All authors analyzed the data and provided the improvement methods. Chia-Hsien Yeh and Yu-Cheng Lin wrote the paper.

Conflicts of Interest

The authors declare no conflict of interest.

References

  1. Ascheim, S.; Zondek, B. Hypophysenvorderlappen hormone und ovarialhormone im Harn von Schwangeren. Klin Wochenschr 1927, 6, 13–21. [Google Scholar]
  2. Yalow, R.S.; Berson, S.A. Immunoassay of endogenous plasma insulin in man. J. Clin. Investig. 1960, 39, 1157–1175. [Google Scholar]
  3. McNaught, R.W.; France, J.T. Studies of the biochemical basis of steroid sulphatase deficiency: Preliminary evidence suggesting a defect in membrane-enzyme structure. J. Steroid Biochem. 1980, 13, 363–373. [Google Scholar]
  4. Harrison, G.; Haffey, P.; Golub, E.E. A nanogram-level colloidal gold single reagent quantitative protein assay. Anal. Biochem. 2008, 380, 1–4. [Google Scholar]
  5. Leung, W.; Chan, C.P.; Rainer, T.H.; Ip, M.; Cautherley, G.W.H.; Renneberga, R. InfectCheck CRP barcode-style lateral flow assay for semi-quantitative detection of C-reactive protein in distinguishing between bacterial and viral infections. J. Immunol. Methods 2008, 336, 30–36. [Google Scholar]
  6. Abe, C.; Hirano, K.; Tomiyama, T. Simple and rapid identification of the mycobacterium tuberculosis complex by immunochromatographic assay using Anti-MPB64 monoclonal antibodies. J. Clin. Microbiol. 1999, 37, 3693–3697. [Google Scholar]
  7. Zhang, W.N.; Zhao, Z.Y. Three-color data reproduction algorithm and implementation for the color image based on CCD and DSPs. Comput. Eng. 2002, 28, 111–113. [Google Scholar]
  8. Zhou, R.Z.; He, J.; Hong, Z.L. Adaptive algorithm of auto white balance for digital camera. J. Comput. Aided Des. Comput. Graph. 2005, 17, 529–533. [Google Scholar]
  9. Zheng, D.Z.; Wu, Z.L.; Wang, S. Detecting method of quantitative colloidal gold test strip concentration based on the DSP image processing. Proceedings of the IEEE 4th International iCBBE Conference (IEEE iCBBE 2010), Chengdu, China, 18–20 June 2010; pp. 1–4.
  10. Jiang, H.Y.; Du, M. Research on the detection of gold immunochromatographic assay by the image histogram feature vectors and fuzzy C-means. Proceedings of the IEEE 8th International FSKD Conference (IEEE FSKD 2011), Shanghai, China, 26–28 July 2011; pp. 467–471.
  11. Yang, S.-C.; Huang, K.-S.; Chen, H.-Y.; Lin, Y.-C. Determination of optimum gene transfection conditions using the taguchi method for an electroporation microchip. Sens. Actuators B Chem. 2008, 132, 551–557. [Google Scholar]
  12. Yang, S.-C.; Huang, K.-S.; Lin, Y.-C. Optimization of a pulsed carbon dioxide snow jet for cleaning CMOS image sensors by using the taguchi method. Sens. Actuators A Phys. 2007, 139, 265–271. [Google Scholar]
  13. Yen, Y.-T.; Fang, T.-H.; Lin, Y.-C. Application of a taguchi method technique in determining the laminating process parameters for a bonding sheet. J. Electron. Packag. 2010, 132, 041005:1–041005:5. [Google Scholar]
  14. Yen, Y.-T.; Fang, T.-H.; Lin, Y.-C. Optimization of screen-printing parameters of SN9000 Ink for pinholes using the taguchi method in chip on film packaging. Robot. Comput. Integr. Manuf. 2011, 27, 531–537. [Google Scholar]
  15. Lin, M.-Y.; Tsao, C.-C.; Hsu, C.-Y.; Chiou, A.-H.; Huang, P.-C.; Lin, Y.-C. Optimization of micro milling electrical discharge machining of Inconel 718 by Grey-Taguchi method. Trans. Nonferrous Metals Soc. China 2013, 23, 661–666. [Google Scholar]
  16. Rao, R.S.; Kumar, C.G.; Prakasham, R.S.; Hobbs, P.J. The Taguchi methodology as a statistical tool for biotechnological applications: A critical appraisal. Biotechnol. J. 2008, 3, 510–523. [Google Scholar]
  17. Wu, D.H.; Yen, Y.T. Robust design of quartz crystal microbalance using finite element and Taguchi method. Sens. Actuators B Chem. 2003, 92, 337–344. [Google Scholar]
  18. Oktem, H.; Erzurumlu, T. Application of Taguchi optimization technique in determining plastic injection molding process parameters for a thin-shell part. Mater. Des. 2007, 28, 1271–1278. [Google Scholar]
  19. Chen, R.S.; Lin, H.C. Optimal dimension of PQFP by using Taguchi method. Compos. Struct. 2000, 49, 1–8. [Google Scholar]
  20. Hung, Y.H.; Huang, M.L. Optimizing the controller IC for micro HDD process based on Taguchi methods. Microelectron. Reliabil. 2006, 46, 1183–1188. [Google Scholar]
  21. Lee, H.C.; Park, O.O. Round pinholes in indium-tin-oxide thin films on the glass substrates: A Taguchi method analysis and theoretical approach to their origins. Vacuum 2004, 72, 411–418. [Google Scholar]
  22. Rosa, J.L.; Robin, A.; Silva, M.B.; Baldan, C.A.; Peres, M.P. Electrodeposition of copper on titanium wires: Taguchi experimental design approach. J. Mater. Process. Technol. 2009, 209, 1181–1188. [Google Scholar]
  23. Rao, R.S.; Parkasham, R.S.; Prasad, K.K.; Rajesham, S.; Sama, P.N.; Rao, L.V. Xylitol production by Candida sp.: Parameter optimization using Taguchi approach. Process. Biochem. 2004, 39, 951–956. [Google Scholar]
Figure 1. The diagram of hCG reaction method in lateral flow immunoassay.
Figure 1. The diagram of hCG reaction method in lateral flow immunoassay.
Sensors 14 16148f1 1024
Figure 2. Illustration of the optical inspection system.
Figure 2. Illustration of the optical inspection system.
Sensors 14 16148f2 1024
Figure 3. The control line and test line of the hCG strip was captured by the optical inspection system.
Figure 3. The control line and test line of the hCG strip was captured by the optical inspection system.
Sensors 14 16148f3 1024
Figure 4. Response graph of the control factors on the S/N functions.
Figure 4. Response graph of the control factors on the S/N functions.
Sensors 14 16148f4 1024
Figure 5. Interaction graphs of the first interaction. (a) A×F; (b) A×I; and (c) F×I; (d) The second interaction of A×I.
Figure 5. Interaction graphs of the first interaction. (a) A×F; (b) A×I; and (c) F×I; (d) The second interaction of A×I.
Sensors 14 16148f5 1024
Figure 6. The relationship between grayscale and the hCG concentration.
Figure 6. The relationship between grayscale and the hCG concentration.
Sensors 14 16148f6 1024
Table 1. The experiential control factors for the Taguchi approach.
Table 1. The experiential control factors for the Taguchi approach.
Control FactorsLevel

12
ABacklight compensationTRUEFALSE
BBrightness−8−4
CContrast0.40.5
DExposure0.40.3
EGain20
FGamma13
GHue00.4
HSaturation50100
ISharpness03
JWhite balanceAuto2800
Table 2. Effects of control factors on the S/N functions.
Table 2. Effects of control factors on the S/N functions.
FactorLevel 1Level 2E1-2RangeRank
A41.743544.89243.14893.14893
B43.736442.8995−0.83680.83689
C43.921942.7140−1.20801.20806
D42.157844.47812.32042.32044
E43.890642.7453−1.14521.14527
F46.998439.6375−7.36097.36091
G43.782642.8533−0.92920.92928
H42.672943.96301.29021.29025
I41.381745.25423.87253.87252
J42.960043.67590.71600.716010
K43.589743.0462−0.54350.543511

Share and Cite

MDPI and ACS Style

Yeh, C.-H.; Zhao, Z.-Q.; Shen, P.-L.; Lin, Y.-C. Optimization of an Optical Inspection System Based on the Taguchi Method for Quantitative Analysis of Point-of-Care Testing. Sensors 2014, 14, 16148-16158. https://doi.org/10.3390/s140916148

AMA Style

Yeh C-H, Zhao Z-Q, Shen P-L, Lin Y-C. Optimization of an Optical Inspection System Based on the Taguchi Method for Quantitative Analysis of Point-of-Care Testing. Sensors. 2014; 14(9):16148-16158. https://doi.org/10.3390/s140916148

Chicago/Turabian Style

Yeh, Chia-Hsien, Zi-Qi Zhao, Pi-Lan Shen, and Yu-Cheng Lin. 2014. "Optimization of an Optical Inspection System Based on the Taguchi Method for Quantitative Analysis of Point-of-Care Testing" Sensors 14, no. 9: 16148-16158. https://doi.org/10.3390/s140916148

Article Metrics

Back to TopTop