Next Article in Journal
A Novel Unsupervised Segmentation Quality Evaluation Method for Remote Sensing Images
Next Article in Special Issue
A Simple Assay for Ultrasensitive Colorimetric Detection of Ag+ at Picomolar Levels Using Platinum Nanoparticles
Previous Article in Journal
Comparison between Random Forests, Artificial Neural Networks and Gradient Boosted Machines Methods of On-Line Vis-NIR Spectroscopy Measurements of Soil Total Nitrogen and Total Carbon
Previous Article in Special Issue
Low Cost Lab on Chip for the Colorimetric Detection of Nitrate in Mineral Water Products
 
 
Font Type:
Arial Georgia Verdana
Font Size:
Aa Aa Aa
Line Spacing:
Column Width:
Background:
Article

Development and Elucidation of a Novel Fluorescent Boron-Sensor for the Analysis of Boronic Acid-Containing Compounds

Research Center of Boron Neutron Capture Therapy, Osaka Prefecture University, 1-1 Gakuen-cho, Nakaku, Sakai, Osaka 599-8531, Japan
*
Author to whom correspondence should be addressed.
Sensors 2017, 17(10), 2436; https://doi.org/10.3390/s17102436
Submission received: 14 September 2017 / Revised: 10 October 2017 / Accepted: 20 October 2017 / Published: 24 October 2017
(This article belongs to the Special Issue Fluorescent Probes and Sensors)

Abstract

:
Novel boron-containing drugs have recently been suggested as a new class of pharmaceuticals. However, the majority of current boron-detection techniques require expensive facilities and/or tedious pretreatment methods. Thus, to develop a novel and convenient detection method for boron-based pharmaceuticals, imine-type boron-chelating-ligands were previously synthesized for use in a fluorescent sensor for boronic acid containing compounds. However, the fluorescence quantum yield of the imine-type sensor was particularly low, and the sensor was easily decomposed in aqueous media. Thus, in this paper, we report the development of a novel, convenient, and stable fluorescent boron-sensor based on O- and N-chelation (i.e., 2-(pyridine-2yl)phenol), and a corresponding method for the quantitative and qualitative detection of boronic acid-containing compounds using this commercially available sensor is presented.

1. Introduction

The use of boronic acid-containing compounds has recently received growing interest in a range of fields, such as materials science, analytical chemistry, chemical biology, and pharmacology. In particular, a large number of studies focusing on the interactions between boron compounds and biomolecules such as sugars, proteins and peptides have been reported in recent years [1,2,3,4,5,6]. For example, in the field of pharmacology, boronic acid-containing compounds have been developed as boron carriers for boron neutron capture therapy (BNCT) [7], and as antibacterial agents, protease inhibitors, sugar sensors, and cell-penetrating peptides. In addition, new boron-containing drugs, including p-borono-L-phenylalanine (L-BPA, for BNCT), L-BPA-fructose complex (L-BPA-Fc) [8,9,10], bortezomib (for the treatment of multiple myeloma) [11,12], and tavaborole (an antifungal drug for the treatment of onychomycosis) [13] have been suggested as a new class of pharmaceuticals [14,15] (Figure 1).
During the development of novel pharmaceutical compounds, drug distribution analysis is of particular importance. For example, the distribution of boron-based pharmaceuticals in tumor tissue and normal tissue must be determined to elucidate the suitability of pharmaceuticals for BNCT, and monitoring of the boron concentration in bloodstream is of key importance in the BNCT treatment process. In this context, evaluation of the concentration of boron-based pharmaceuticals in biological environments should be possible through the detection of boron, since biological tissues generally contain little or no boron. However, the majority of boron detection methods, such as those based on prompt gamma-ray analysis (PGA) and inductively coupled plasma optical emission spectrometry (ICP-OES) are costly, and often require extensive sample pretreatment.
In this context, we recently designed and synthesized a novel fluorescent probe for boronic acid, namely DAHMI (1) (Figure 2) [16]. This probe reacted rapidly with boron-based pharmaceuticals in aqueous media, resulting in the emission of blue fluorescence by the formed DAHMI-boron complexes. Furthermore, DAHMI allowed visualization of the distribution of boron-containing pharmaceuticals such as L-BPA, and tavabolore in live tumor cells without complicated pretreatment [17]. However, the fluorescence quantum yields of the resulting DAHMI-boron complexes were extremely low (i.e., <1%), and DAHMI was easily decomposed by hydrolysis in aqueous media. As such, DAHMI is not particularly suitable for use as a boron sensor in the quantitative analysis of boron compounds in biological samples.
Thus, in this paper, we report the development of a novel, convenient, and stable fluorescent probe for boronic acid-containing compounds, and present a subsequent elucidation of the fluorescence properties of the resulting sensor-boronic acid complexes.

2. Results and Discussion

In order for a fluorescent sensor to detect boronic acid derivatives in biological environments, the following criteria must be met: (i) rapid reaction with boronic acid at room temperature; (ii) a change in emission upon complexation with boronic acid; (iii) fluorescence in water; and (iv) stability in water.
Thus, we herein employed a range of commercially available and easily prepared chelating ligands 26 as precursors for the boron sensor (Figure 3) [18,19,20,21]. These ligands were considered suitable as they were both soluble and stable in a 50 vol % DMSO/H2O solution, and because they emit very weak fluorescence in aqueous solutions. To confirm the potential of our previously prepared fluorescent probe DAHMI in addition to the five chelating ligands for use as boron sensors, we measured the fluorescence spectra of compounds 16 and their corresponding BPA complexes in a 50 vol % DMSO/PBS (phosphate-buffered saline) solution at 25 °C (Table 1). Although compounds 2 and 6 did not react with BPA under these conditions, DAHMI and compounds 35 reacted to give fluorescent complexes with BPA. This result suggests that N, O-type chelating ligands are suitable for use as fluorescent boron-sensors. In addition, we observed that the excitation and fluorescence wavelengths of these complexes differed from those of the corresponding free ligands. In particular, the fluorescence wavelength of the 5-BPA (5 = 2-(pyridine-2-yl)phenol) complex was blue shifted by ~20 nm, and the Stokes shift of the complex was extremely large. Furthermore, the maximum fluorescence quantum yield was observed for 5-BPA, with a 15-fold higher yield being observed than for the DAHMI-BPA complex. Indeed, this 5-BPA complex showed particular potential for use as a sensor, as it was prepared rapidly by the simple mixing of a solution of 5 with a solution of BPA (1.0 eq.) at room temperature in 50 vol % DMSO/PBS. Upon mixing, the fluorescence intensity of 5-BPA complex was reached a maximum within a few seconds, and this complex was stable in solution over 24 h (Figure 4). These results indicate that compound 5 is suitable for use as a fluorescent sensor in the detection of boronic acid-containing compounds.
Thus, to confirm the potential of boron sensor 5 for use in the qualitative analysis of boronic acid-containing compounds, a number of boron compounds were spotted onto silica gel plates and stained using a 1.0 mM solution of 5 in acetone (Figure 5). Although boron sensor 5 was visible under irradiation using a 254 nm hand-held UV lamp, the spot of 5 did not emit fluorescence under 254 or 365 nm UV lamps. Thus, as shown in Figure 5, all spots corresponding to the different boronic acid-containing compounds, including L-BPA, bortezomib and tavaborole produced bright blue fluorescence using a standard short-wave UV lamp (365 nm) following staining with compound 5. In particular, boronic ester-type protected derivatives, such as pinacolato, 1,3-dihydroxydimetyl, trifluoroborate and L-BPA-Fc, exhibited strong fluorescence upon complexation with 5. However, in the case of boronic amide type protected derivatives, such as N-methyliminodiacetic acid and 1,8-diaminonaphtnalene, only weak fluorescence was observed. As a control, a number of boron-free compounds were also spotted onto the silica plates, but no fluorescence was observed under UV irradiation at either 254 or 365 nm (Figure 6). These results therefore suggest that boron sensor 5 is a useful tool for the qualitative analysis of boronic acid-containing compounds.
Finally, to determine the potential of boron sensor 5 in the quantitative analysis of boron pharmaceuticals, we examined the relationship between the concentration of L-BPA-Fc and the emission of the complex upon staining with 5 in 50 vol % DMSO/PBS using a standard plate reader. As shown in Figure 7, the emission intensity correlated positively with the concentration of L-BPA-Fc, thereby indicating that boron sensor 5 is suitable for use in the quantitative analysis of L-BPA-Fc (0.5–1000 μM, 0.005–10 Bppm, R2 > 0.99). Furthermore, the detection limit of this method was comparable to ICP-OES.

3. Conclusions

We herein developed and elucidated a novel efficient and commercially available fluorescent sensor based on O- and N- chelation (i.e., 2-(pyridine-2yl)phenol) for the analysis of boronic acid-containing compounds. We found that this boron sensor reacts rapidly with boronic acid at room temperature, and that it selectively detects boronic acid-containing compounds. Furthermore, the quantitative analyses of boronic acid-containing compounds using this sensor were carried out using a standard plate reader, with the compounds of interest being detected in concentrations of 0.5–1000 μM. These results therefore suggest that this fluorescent boron sensor is suitable for use in the qualitative and quantitative analysis of boronic acid-containing compounds. We therefore expect that the system reported herein will be applicable in the detection of boron-based pharmaceuticals, with the potential to replace current expensive and tedious analytical methods.

4. Experimental Section

4.1. Genaral

L-BPA was provided by the Stella Pharma Corporation (Osaka, Japan), while bortezomib and tavaborole were purchased from Cosmo Bio Co., Ltd. (Tokyo, Japan). Compounds 2, 3, and 5 were purchased from Wako Pure Chemical Industries, Ltd. (Osaka, Japan). Compounds 4 and 6 were prepared according to a previous literature method [19,21]. Fluorescence spectra were measured on a FP-8200 spectrometer (JASCO Corporation, Tokyo, Japan). Absolute quantum yields were determined by the Hamamatsu C9920-01 calibrated integrating sphere system (Hamamatsu Photonics K.K., Shizuoka, Japan).

4.2. Preparation of the Sensor-BPA Complexes

A solution of boron sensor (1.0 mM in DMSO, 2.5 mL) was added to a solution of BPA (1.0 mM in PBS buffer, 2.5 mL). After allowing this mixture to stand for 10 min at 37 °C, the resulting solution was employed for fluorescence measurement.

4.3. Silica Gel Plate Staining Using Boron Sensor 5

L-BPA and L-BPA-Fc were prepared as aqueous solutions (10 mM) concentrations while solutions of all other boron-containing compounds were prepared in acetone (10 mM). Each sample solution (5 μL) was applied to a glass-backed silica-gel TLC plate containing the F254 fluorescent indicator (Merck KGaA, Darmstadt, Germany) and allowed to dry under air at room temperature prior to treatment of the test compound spot with a solution of boron sensor 5 (1.0 mM in acetone). After allowing to dry once again under air at room temperature, the plates were visualized by illumination at either 254 or 365 nm using a handheld UV lamp, and photographic images were recorded.

4.4. Effect of BPA Concentration on the Emitted Fluorescence Following Staining with 5

To a 96-well microplate (FluoroNuncTM flat bottom black polystyrene plate, Thermo Fisher Scientific, Waltham, MA) were added of a L-BPA-Fc solution of the desired concentration (50 μL, 0.5–1000 μM in H2O) and a solution of boron sensor 5 (50 μL, 10 mM in DMSO. After mixing for 5 min at 37 °C, the fluorescence intensity was measured using a Fluoroskan Ascent FL microplate reader (Thermo Fisher Scientific, Waltham, MA, USA).

Supplementary Materials

The following are available online at https://www.mdpi.com/1424-8220/17/10/2436/s1.

Acknowledgments

We would like to thank Yoshihiro Yamaguchi of the Kindai University for the measurement of fluorescence properties. This work was supported by the Nakatani Foundation for Advancement of Measuring Technologies in Biomedical Engineering grant program for biomedical engineering research, and by the Project for Cancer Research and Therapeutic Evolution (PCREATE) from the Japan Agency for Medical Research and Development, AMED.

Author Contributions

Y.H. and M.K. designed the experiments. Y.H., Y.O. and H.T. performed the synthesis of the compounds. Y.H. and M.I. performed the measurement of fluorescence properties. Y.H. wrote the manuscript. All authors discussed the results and implications of the study and approved the final manuscript.

Conflicts of Interest

The authors declare no conflict of interest.

References

  1. Yang, W.; Gao, X.; Wang, B. Boronic acid compounds as potential pharmaceutical agents. Med. Res. Rev. 2003, 23, 346–368. [Google Scholar] [CrossRef] [PubMed]
  2. Chaudhary, P.M.; Murthy, R.V.; Yadav, R.; Kikkeri, R. A rationally designed peptidomimetic biosensor for sialic acid on cell surfaces. Chem. Commun. 2015, 51, 8112–8115. [Google Scholar] [CrossRef] [PubMed]
  3. Dilek, O.; Lei, Z.; Mukherjee, K.; Bane, S. Rapid formation of a stable boron–nitrogen heterocycle in dilute, neutral aqueous solution for bioorthogonal coupling reactions. Chem. Commun. 2015, 51, 16992–16995. [Google Scholar] [CrossRef] [PubMed]
  4. Okuro, K.; Sasaki, M.; Aida, T. Boronic acid-appended molecular glues for ATP-responsive activity modulation of enzymes. J. Am. Chem. Soc. 2016, 138, 5527–5530. [Google Scholar] [CrossRef] [PubMed]
  5. Palombella, V.J.; Conner, E.M.; Fuseler, J.W.; Destree, A.; Davis, J.M.; Larous, F.S.; Wolf, R.E.; Huang, J.; Brand, S.; Elliott, P.J.; et al. Role of the proteasome and NF-kB in streptococcal cell wall-induced polyarthritis. Proc. Natl. Acad. Sci. USA 1998, 95, 15671–15676. [Google Scholar] [PubMed]
  6. Piest, M.; Ankoné, M.; Engbersen, J.F.J. Carbohydrate-interactive pDNA and siRNA gene vectors based on boronic acid functionalized poly(amido amine)s. J. Controlled Release 2013, 169, 266–275. [Google Scholar] [CrossRef] [PubMed]
  7. Soloway, A.H.; Tjarks, W.; Barnum, B.A.; Rong, F.G.; Barth, R.F.; Codogni, I.M.; Wilson, J.G. The chemistry of neutron capture therapy. Chem. Rev. 1998, 98, 1515–1562. [Google Scholar] [CrossRef] [PubMed]
  8. Mishima, Y.; Honda, C.; Ichihashi, M.; Obara, H.; Ichihashi, M.; Obara, H.; Hiratsuka, J.; Fukuda, H.; Karashima, H.; Kobayashi, T.; et al. Treatment of malignant melanoma by single thermal neutron capture therapy with melanoma-seeking 10B-compound. Lancet 1989, 2, 388–389. [Google Scholar] [PubMed]
  9. Hattori, Y.; Asano, T.; Kirihata, M.; Yamaguchi, Y.; Wakamiya, T. Development of the first and practical method for enantioselective synthesis of 10B-enriched p-borono-L-phenylalanine. Tetrahedron Lett. 2008, 49, 4977–4980. [Google Scholar] [CrossRef]
  10. Andoh, T.; Fujimoto, T.; Sudo, T.; Fujita, I.; Imabori, M.; Moritake, H.; Sugimoto, T.; Sakuma, Y.; Takeuchi, T.; Kawabata, S.; et al. Boron neutron capture therapy for clear cell sarcoma (CCS): Biodistribution study of p-borono-l-phenylalanine in CCS-bearing animal models. Appl. Radiat. Isot. 2011, 69, 1721–1724. [Google Scholar] [CrossRef] [PubMed]
  11. Adams, A. Development of the proteasome inhibitor PS-341. Oncologist 2002, 7, 9–16. [Google Scholar] [CrossRef] [PubMed]
  12. Girbig, A.K.; Kalesse, M. Synthesis and pharmacology of proteasome inhibitors. Angew. Chem. Int. Ed. 2013, 52, 5450–5488. [Google Scholar]
  13. Jinna, S.; Finch, J. Spotlight on tavaborole for the treatment of onychomycosis. Drug Des. Devel. Ther. 2015, 9, 6185–6190. [Google Scholar] [PubMed]
  14. Baker, S.J.; Ding, C.Z.; Akama, T.; Zhang, Y.; Hernandez, V.; Xia, Y. Therapeutic potential of boron-containing compounds. Future Med. Chem. 2009, 1, 1275–1288. [Google Scholar] [CrossRef] [PubMed]
  15. Smoum, R.; Rubinstein, A.; Dembisky, V.M.; Srebnik, M. Boron containing compounds as protease inhibitors. Chem. Rev. 2012, 112, 4156–4220. [Google Scholar] [CrossRef] [PubMed]
  16. Hattori, Y.; Ishimura, M.; Ohta, Y.; Takenaka, H.; Watanabe, T.; Tanaka, H.; Ono, K.; Kirihata, M. Detection of boronic acid derivatives in cells using a fluorescent sensor. Org. Biomol. Chem. 2015, 13, 6927–6930. [Google Scholar] [CrossRef] [PubMed]
  17. Hattori, Y.; Ishimura, M.; Ohta, Y.; Takenaka, H.; Kirihata, M. Visualization of boronic acid-containing pharmaceuticals in live tumor cells using a fluorescent boronic acid sensor. ACS Sens. 2016, 1, 1394–1397. [Google Scholar] [CrossRef]
  18. Nagata, Y.; Chujo, Y. Synthesis of methyl-substituted main-chain-type organoboron quinolate polymers and their emission color tuning. Macromolecules 2008, 41, 2809–2813. [Google Scholar] [CrossRef]
  19. Kubota, Y.; Hara, H.; Tanaka, S.; Funabiki, K.; Matsui, M. Synthesis and fluorescence properties of novel pyrazine boron complexes bearing a β-iminoketone ligand. Org. Lett. 2011, 13, 6544–6547. [Google Scholar] [CrossRef] [PubMed]
  20. Kim, N.G.; Shin, G.H.; Lee, M.H.; Do, Y. Four-coordinate boron compounds derived from 2-(2-pyridyl)phenol ligand as novel hole-blocking materials for phosphorescent OLEDs. J. Organomet. Chem. 2009, 694, 1922–1928. [Google Scholar] [CrossRef]
  21. Li, Y.; Liu, Y.; Bu, W.; Guo, J.; Wang, Y. A mixed pyridine–phenol boron complex as an organic electroluminescent material. Chem. Commun. 2000, 1551–1552. [Google Scholar] [CrossRef]
Figure 1. A selection of boron-containing pharmaceuticals.
Figure 1. A selection of boron-containing pharmaceuticals.
Sensors 17 02436 g001
Figure 2. Complex formation using the previously reported fluorescent boron sensor DAHMI (1).
Figure 2. Complex formation using the previously reported fluorescent boron sensor DAHMI (1).
Sensors 17 02436 g002
Figure 3. Candidate compounds for the fluorescent boron sensor.
Figure 3. Candidate compounds for the fluorescent boron sensor.
Sensors 17 02436 g003
Figure 4. Variation in the fluorescence spectra of the 5-BPA complex in 50 vol % DMSO/PBS (0.2 mM, excitation wavelength: 355 nm) at 25 °C. (a) prepared after 0–60 min; (b) prepared after 0–36 h.
Figure 4. Variation in the fluorescence spectra of the 5-BPA complex in 50 vol % DMSO/PBS (0.2 mM, excitation wavelength: 355 nm) at 25 °C. (a) prepared after 0–60 min; (b) prepared after 0–36 h.
Sensors 17 02436 g004
Figure 5. Staining test of various boron-containing compounds spotted onto silica-gel plates followed by the addition of boron sensor 5 (viewed by illumination at 254 or 365 nm using a handheld UV lamp).
Figure 5. Staining test of various boron-containing compounds spotted onto silica-gel plates followed by the addition of boron sensor 5 (viewed by illumination at 254 or 365 nm using a handheld UV lamp).
Sensors 17 02436 g005
Figure 6. Staining test of boron-free compounds spotted onto silica-gel plates followed by the addition of boron sensor 5 (viewed by illumination at 254 or 365 nm using a handheld UV lamp).
Figure 6. Staining test of boron-free compounds spotted onto silica-gel plates followed by the addition of boron sensor 5 (viewed by illumination at 254 or 365 nm using a handheld UV lamp).
Sensors 17 02436 g006
Figure 7. Effect of L-BPA-Fc concentration on the fluorescence intensity following staining with boron-sensor 5 (10 mM in 50 vol % DMSO/PBS, ex λ: 360 nm, em λ: 460 nm).
Figure 7. Effect of L-BPA-Fc concentration on the fluorescence intensity following staining with boron-sensor 5 (10 mM in 50 vol % DMSO/PBS, ex λ: 360 nm, em λ: 460 nm).
Sensors 17 02436 g007
Table 1. Fluorescence properties of the various ligands and ligand-BPA complexes [a].
Table 1. Fluorescence properties of the various ligands and ligand-BPA complexes [a].
LigandLigand OnlyLigand-BPA Complex
Ex Max (nm)Em Max (nm)Stokes Shift (cm−1)φEx Max (nm)Em Max (nm)Stokes Shift (cm−1)φ
1413551606440843012540.6%
2374531374531
3419477290242151643733.3%
4340384337035243353141.2%
5376483589235546466179.3%
6376376
[a] Measured at a concentration of 1.0 mM in 50 vol % DMSO/PBS at 25 °C.

Share and Cite

MDPI and ACS Style

Hattori, Y.; Ogaki, T.; Ishimura, M.; Ohta, Y.; Kirihata, M. Development and Elucidation of a Novel Fluorescent Boron-Sensor for the Analysis of Boronic Acid-Containing Compounds. Sensors 2017, 17, 2436. https://doi.org/10.3390/s17102436

AMA Style

Hattori Y, Ogaki T, Ishimura M, Ohta Y, Kirihata M. Development and Elucidation of a Novel Fluorescent Boron-Sensor for the Analysis of Boronic Acid-Containing Compounds. Sensors. 2017; 17(10):2436. https://doi.org/10.3390/s17102436

Chicago/Turabian Style

Hattori, Yoshihide, Takuya Ogaki, Miki Ishimura, Yoichiro Ohta, and Mitsunori Kirihata. 2017. "Development and Elucidation of a Novel Fluorescent Boron-Sensor for the Analysis of Boronic Acid-Containing Compounds" Sensors 17, no. 10: 2436. https://doi.org/10.3390/s17102436

Note that from the first issue of 2016, this journal uses article numbers instead of page numbers. See further details here.

Article Metrics

Back to TopTop