Next Article in Journal
SITHON: An Airborne Fire Detection System Compliant with Operational Tactical Requirements
Previous Article in Journal
Detection of Neolithic Settlements in Thessaly (Greece) Through Multispectral and Hyperspectral Satellite Imagery
 
 
Font Type:
Arial Georgia Verdana
Font Size:
Aa Aa Aa
Line Spacing:
Column Width:
Background:
Article

Flexible Electronics Sensors for Tactile Multi-Touching

1
Department of Engineering Science, National Cheng Kung University, Tainan 701, Taiwan
2
Microsystems Technology Center, Industrial Technology Research Institute, Tainan 709, Taiwan
3
Institute of Mechanical and Electromechanical Engineering, National Formosa University, Yunlin 632, Taiwan
*
Author to whom correspondence should be addressed.
Sensors 2009, 9(2), 1188-1203; https://doi.org/10.3390/s9021188
Submission received: 12 February 2009 / Revised: 20 February 2009 / Accepted: 23 February 2009 / Published: 24 February 2009
(This article belongs to the Section Chemical Sensors)

Abstract

:
Flexible electronics sensors for tactile applications in multi-touch sensing and large scale manufacturing were designed and fabricated. The sensors are based on polyimide substrates, with thixotropy materials used to print organic resistances and a bump on the top polyimide layer. The gap between the bottom electrode layer and the resistance layer provides a buffer distance to reduce erroneous contact during large bending. Experimental results show that the top membrane with a bump protrusion and a resistance layer had a large deflection and a quick sensitive response. The bump and resistance layer provided a concentrated von Mises stress force and inertial force on the top membrane center. When the top membrane had no bump, it had a transient response delay time and took longer to reach steady-state. For printing thick structures of flexible electronics sensors, diffusion effects and dimensional shrinkages can be improved by using a paste material with a high viscosity. Linear algorithm matrixes with Gaussian elimination and control system scanning were used for multi-touch detection. Flexible electronics sensors were printed with a resistance thickness of about 32 μm and a bump thickness of about 0.2 mm. Feasibility studies show that printing technology is appropriate for large scale manufacturing, producing sensors at a low cost.

1. Introduction

Multi-touch technologies are usually based on cameras and optical systems [1-4] that use emission and reflection to recognize hand gestures or objects. The use of capacitive sensing [5] is another possible sensing method, but it requires attaching a mesh-shape to achieve the interaction between transmitter and receiver. One of the most widespread multi-touch technologies uses the Frustrated Total Internal Reflection (FTIR) proposed by Jeff Han [6]. A comparison of multi-touch technologies is given in Table 1. The most common systems are expensive because they use special control hardware and require bulky equipment. A few studies, such as those done by Apple and N-trig [7,8], have focused on projected-capacitive technology for portable devices. A capacitive coupling between neighboring electrodes changes its capacitance as an object approaches the field lines projected from one electrode to another. However, projected-capacitive technology has a limited maximum size because the number of sensor electrodes needs to increase geometrically as the screen size increases. In multi-touch sensors, there is no organic resistance material between the two electrodes. It is very difficult to correctly identify which element was really touched because the mutual conduction of column and row electrodes is easily confused during the column and row scanning processes. In addition, multi-touch screens are mostly made of glass, which is difficult to bend.
Therefore, we propose a novel flexible multi-touch sensor design that prints organic thixotropic resistance materials on a top polyimide (PI) film. We also use an algorithm matrix and control system scanning to solve the array matrix for multi-touch switch identification in the tactile sensors. Flexible electronics actuators for realizing large scale and low-cost applications have been gradually developed in recent years [11,12]. Especially, flexible displays [13,14] and flexible organic transistors [15-17] have been successfully demonstrated using printing technologies. A few studies on flexible electronics sensors, usually using solid components integrated into polymer materials, have focused on small scale pressure [18], temperature [19,20], and humidity [21] sensors. Fabrication technologies for flexible electronics include screen printing [22], ink-jet printing [23,24], and the roll to roll process [25].
We have designed a gap between the bottom electrode and the resistance layer to eliminate erroneous signals during bending actions. For optimal flexible structure characteristics, a protrusion (bump) on the top membrane is used to enhance the sensing sensitivity response. A high viscosity thixotropic material is used to print the thick bump structures to reduce the diffusive effects and dimensional shrinkage after printing and curing. Mechanical properties were investigated by analysis of the deflection and stress distributions using finite element analysis (FEA). The feasibility of fabricating low-cost printable sensors for applications in flexible electronics is demonstrated.

2. Experimental Procedure

2.1. Fabrication

This study used commercial PI films and screen printing technology to design and fabricate a flexible large area electronics sensor. PI films with copper foils are widely used in flexible electronics sensors for flexible printed circuits [26-28]. The PI film's mechanical hardness and stress characteristics are about 0.181 GPa, and 87.14 MPa, respectively [29]. The sensor structures mainly include two PI films, one cover layer, and bump protrusions. Two PI films were used as the top and bottom films of the flexible electronics sensor. The top film contains the row electrodes, the organic resistance layers, and the bump structures. The bottom film includes the column electrodes and a cover film, which was laminated into the PI film using hot pressing to form the post layer for supporting the membrane of the top film. The fabrication process mainly used a Model EKRA-E1 screen printer (Ekra, Japan), for printing materials on a flexible substrate. During the fabrication process, materials were transferred onto a substrate using a squeegee via an attached stencil mask. The fabrication process was carried out as shown in Figure 1.
First, the electrode patterns on the bottom film with a 12 μm copper foil (I), were defined for column and sensing electrodes using the photolithography method. The bottom film was then put into a solution of CuSO4 for electroless plating of Au, to a thickness of about 5 μm, to avoid the oxidation of the copper foil. Next, a cover layer with lattice patterns was laminated on the bottom film using hot pressing to form post structures (II). The hot-press process was performed at a temperature of 180°C for 20 minutes.
The second part of the top film, which contains the row electrodes (i), is similar to that of the bottom substrate, except that it has pass-through holes that were drilled using the punching method. Cu was coated on the side of these holes using a chemical plating to transfer the output signal from the back to the top view of top film. An organic resistance material (ii), Model EPO 4X330, with a viscosity of 8 × 104 cp and a glass transition temperature of 190°C, was printed on sensing electrode areas using a screen stencil mask. The organic resistance was synthesized using a phenolic resin, organic solvents, filler, and carbon black. The phenolic resin is a bisphenol A (C15H16O2) type of organic compound with two phenol functional groups. The organic solvents included dimethylformamide (formula C3H7NO) and diethylene glycol monobutyl ether (formula CH3CH2OCH2CH2OCH2CH2OH). Dimethylformamide (N,N-dimethylformamide), is a hydrophilic aprotic solvent of the organic compound material that facilitates chemical reactions by polar mechanisms. Diethylene glycol monobutyl ether [2-(2-butoxyethoxy)ethanol], is the main dispersing agent for the synthetic resin and filler. The filler and carbon black are 25.6 wt% and 12.0 wt%, respectively.
For organic resistance printing, the stencil mask was a stainless steel sheet, which was made using chemical etching techniques. The printing header was a rubber squeegee of type A with a durometer of 70 and a printed angle of 45°. After top electrode and organic resistance fabrication, the film was turned over. A thixotropic material, type EPO 4X282H, with a viscosity of 106 cp and a glass transition temperature of 150°C was printed on the top film using a screen stencil mask to form bump structures (iii). The bump structures were formed after being cured at a temperature of 150°C for 45 minutes. Finally, both PI films were aligned and assembled to form a flexible electronics sensor using adhesive (III), type Cemedine Super-X No.8008 (Cemedine Co., Japan) which was printed on the top of the post surface using screen technology.

2.2. Control Frame for Multi-touching

In general, in array switch elements for multi-touch use without a resistance layer, it is very difficult to correctly identify which elements are really touched. For example, a 2 × 2 matrix sensor with elements E1 to E4 has only an ON/OFF switch function, with R11, R12, R21, and R22 ignored, as shown in the upper left of Figure 2(a) with a dashed line. If three elements have been touched, e.g. E1, E2, and E3, then E4 will be misread as also being touched because all column and row electrodes are mutually conductive during the column and row scanning processes. An organic resistance material was printed on the surface of the sensing electrodes and an algorithm matrix and control system scanning were used to solve this problem. The schematic control system for multi-touch switching applications is shown in Figure 2(a). The system frame includes a microcontroller, a parallel buffer IC, op-amps, and an array of flexible electronics sensors. The microcontroller, model ATmega32-16MU, Atmel AVR, has three I/O ports. Port A outputs a serial high/low digital signal to the column electrode lines. Port B first sets the high or low impedance signals and then detects the sensing signals from row electrode lines. Port C transmits the sensing data. The parallel buffer IC, 74HC245, provides high driving power to avoid current decay during scanning of sensing. The non-inverting op-amp, μA741, provides a gain of about 60 to enlarge the output voltages. A flexible electronics sensor Rmn (m × n array elements with a resistance of R) had a pitch of 5 mm with 25 × 25 elements.
In the multi-touch detection process, the parallel buffer IC outputs serial digital data to columns via port A. Only one column is the high bit, 1, and the others are the low bit, 0. Port B first sets the serial data to all rows. One row is high impedance and the others are low impedance. Then, port B is changed to detect all row data to identify which elements were touched. For instance, the serial digital data of port A, “VD, VG, …, VG,” outputs “1,0, …, 0” for all columns, indicating that only column 1 was driven. Then, port B sets the impedances of all rows to “high, low, …, low” and is changed to detect all row data. R11 can be detected using algorithm matrix operating. The equivalent circuit of the algorithm matrix for row 1 is shown in Figure 2(b). The algorithm matrix was derived using Kirchhoff's current law, as shown in equation (1). Column 1 was ignored because rows 2 to m had low impedance.
V D V 11 R 11 = V 11 R 12 + V 11 R 13 + + V 11 R 1 n
Similarly, the serial digital data of port A outputs “0,1,0, …, 0” for all columns.
V 12 R 11 = V D V 12 R 12 + V 12 R 13 + + V 12 R 1 n
Therefore, the algorithm matrix of row 1, AY1n=0, can be formed as follows:
[ ( V 11 V D ) V 11 V 11 V 11 V 12 ( V 12 V D ) V 12 V 12 V 1 ( n 1 ) V 1 ( n 1 ) ( V 1 ( n 1 ) V D ) V 1 ( n 1 ) V 1 n V 1 n V 1 n ( V 1 n V D ) ] [ Y 11 Y 12 Y 1 n ] = [ 0 0 0 0 0 ]
where VD is the driving voltage of the microcontroller, entries V11 to V1n are the voltage values of row 1, and Y11 to Y1n are the conductance values of the resistance at row 1, with Y1n=1/R1n. To solve the linear equations, Gaussian elimination was performed in row-echelon form to reduce the matrix. Then, the back-substitution method was used to solve the final equations of Y1n for multi-touch identification. The average value of resistance of elements after the voltage scanning and calculations was about 2.8 kΩ. Similarly, rows 2 to m can be scanned using the same methods to detect the signals. It is noteworthy that the microprocessor for scanning one column and solving the algorithm takes about 0.015 seconds, indicating a response frequency of 150 Hz. The sensor array of our study is 25 × 25, so this is not a problem for our system. However, we think that solving bigger matrixes will create some problems. Maybe the scanning array matrixes can be segmented and a sub-microprocessor can be used to solve the algorithm equations.

2.3. Mechanical Deflection

Consider a square plate for a linear motion equation, simply supported on all edges and subjected to a distributed load, f(x, y), in the z direction, as shown in Figure 3. Assuming the inertial force of the membrane mass is neglected and the membrane is the elastic deflection. If we consider an elemental area dx dy, forces of magnitude Pdx and Pdy act on the sides parallel to the y and x axes, respectively. The forces, F, acting along the z direction due to these forces are:
F x = P 2 δ x 2 d x d y and F y = P 2 δ y 2 d x d y
where P and δ are the pressure and the deflection at the membrane center, respectively.
The pressure force along the z direction is f(x,y)·dx·dy. Hence, the membrane bending by moments distributed can be obtained for the forced transverse vibration in z direction [30,31]:
2 M x x 2 + 2 2 M xy x y + 2 M y y 2 = P ( x , y )
where M x = D [ 2 δ x 2 + υ 2 δ y 2 ], M xy = D ( 1 υ ) 2 δ x y, M y = D [ 2 δ x 2 + υ 2 δ y 2 ], and D = E t m 3 12 ( 1 υ 2 ).
The result of the applied pressure and the membrane deflection is given by:
P = E t m 3 δ ( 1 υ ) w 0 4 ( 1 12 α ( 1 + υ ) + C δ 2 t m 2 )
where tm and w0 are the membrane thickness and width, respectively, and E and ν are the material Young's modulus and Possion's ratio, respectively. C and α are the coefficients, which are 21.62 × (1.41-0.292 × ν) and 1.26 × 10-3 [21] respectively. The membrane characteristics are E = 2.5 GPa, ν = 0.34, tm = 50 μm, and w0 = 5 mm when a pressure of P = 400 MPa is applied on the membrane. The central deflection is 3.59 × 10-4 m.

3. Results and Discussion

3.1. Finite Element Analysis

The design and simulation of a flexible electronics sensor for static tactile analysis with a large deflection were carried out using commercial FEA, ANSYS v.10.0. The effects of the membranes without bumps, with bumps, and with bumps and a resistance layer were used to analyze the deflection characteristics after a constant force was applied on the top surface. The membranes for the simulations, with a constant thickness of 50 μm, were square-shaped suspension structures. Bump sizes with width ratios of 0.2 to 1, relative to the membrane width, and with thicknesses of 0.05, 0.2, and 0.5 mm were considered. During the simulation, all elements were defined by eight nodes with three degrees of freedom at each node. A free mesh with tetrahedral-shaped elements was used to simplify the geometry creation.
For boundary condition settings, the displacements in the bottom of the posts were fixed in all degrees of freedom and the constant forces from 0.5 to 10 N were applied on the top membrane. Young's modulus, Poisson's ratio, and the density of the PI film were 2.5 GPa, 0.34, and 1.42 g/ml, respectively. The simulation results show that the maximum deflection of all cases, δmax, increased with increasing applied force, as shown in Figure 4(a), but the deflection changed less in the membranes without a resistance layer. The membrane with bumps and a resistance layer had larger deflections because the inertia force and the concentrated force increased.
The effects of width and thickness of various bumps, W and tb, are shown in Figure 4(b). For boundary condition settings, the displacements in the bottom of the posts were fixed and a constant force of 7.5 N was applied on top surface of the bumps. Young's modulus, Poisson's ratio, and the density of the bump material were 62 GPa, 0.3, and 1.8 g/ml, respectively. The maximum deflection curves increased significantly when the width ratios decreased, indicating that a larger bump width had a smaller deflection, which was due to the hardness of bump material being higher than that of the membrane material. In addition, membrane deflection curves decreased with increasing bump thickness. The bumps with higher thicknesses acted as rigid structures, reducing the membrane deflection. For the experimental fabrication, bumps with a width ratio of 0.4 and a thickness of 200 μm were selected in the flexible electronics sensor design.
The mechanical characteristics analyses, deflections, and von Mises stress distributions of membranes with bumps and of those with bumps and a resistance structure, are shown in Figure 5. The dimensions of the membrane and the bumps in the simulation structures were 5 × 5 × 0.05 and 2 × 2 × 0.2 mm3, respectively. The maximum deflections and stresses of the membrane with a bump structure after applying a constant force of 5 N were 0.196 mm and 485 MPa, respectively, as shown in Figures 5(a) and (b). The maximum deflection was observable at the center of the membrane, but the maximum stress distributions were concentrated at the bump sides. The membrane with bumps and a resistance layer had a maximum deflection of 0.317 mm and a maximum stress of 480 MPa, as shown in Figures 5(c) and (d). The deflection of the membrane increased by 1.6 times after a resistance structure and a bump structure were added. The increased deflection was caused by an increased concentration of von Mises stress distributions and the inertia force at the bump structure. The maximum stress was less than for the membrane with bumps only because the top structures are a sandwich, which can protect the PI film.

3.2. Printed Sensor Characteristics

The flexible electronics of tactile sensors were successfully fabricated using two PI films. The thicknesses of the top and bottom were 50 and 125 μm. The effective area was 15 × 15 cm2, containing 25 × 25 arrays of sensing pads and bumps, respectively, as shown in Figure 6(a). The widths of the membrane, post, electrode lines, and sensing pads were 5, 0.8, 0.8, and 2 mm, respectively. The thickness of the sensing pad was 17 μm. The post height included a 90 μm cover and a 20 μm adhesive. Experiment results show that the organic resistance material had a uniform thickness and well-defined printing at a squeegee speed of 10 mm/s, a squeegee pressure of 70 kPa, and a separation speed of 0.4 mm/s using the single print mode. After printing, organic resistance material was cured at 190°C for 3 hours.
The bump structures, 2 × 2 × 0.2 mm3, were printed on the top PI film to provide a concentrated force for enhanced touch sensitivity. Results show that bump shapes had excellent morphological profiles, as shown in Figure 6(b), after being printed at a squeegee speed of 10 mm/s, a squeegee pressure of 213 kPa, and a separation speed of 0.4 mm/s using the print-print mode. Therefore, the thixotropy material with a high viscosity reduced the diffusive effects and dimensional shrinkages for printing thick structures. The sensor device after package fabrication was freely flexed without being damaged.
To analyze the printed characteristics, it is necessary to measure the dimensional diffusion and average thickness. The dimensional diffusion ratio of structure dimensions after printing and curing is presented as (Wp - Wi) / Wi × 100 %, where Wi and Wp are the original width and the printed width, respectively. Figure 7 shows the dimensional diffusions in the X and Y directions, which are parallel to and perpendicular to the printing directions, respectively.
Widths of 1 to 5 mm in square shapes were used to investigate the dimension effects. The results show that dimensional diffusion along the printing direction was larger than that in the Y direction. This implies that the materials were easily extruded along the printing direction during the printing process. The average percent diffusions of the resistance structures in the X and Y directions were about 24.3 % and 22.6 %, respectively. The bump material after printing had a smaller diffusion than that of the resistance material because the higher viscosity reduced the dimensional diffusive and shrinkage effects. The average percent diffusions of the bumps after printing in the X and Y directions were about 17.1 % and 16.2 %, respectively.
The values of the mean and the standard deviation for the probability density distribution of the printed resistance layer were 2.93 and 2.29 kΩ, respectively. The probability distribution at two standard deviations from mean values was 82.2 %. The range of resistance values at two standard deviations was used in the multi-touch applications in this study. The printed thicknesses were mostly consistent because the resistance value was relative to the printed thickness. Statistical computations show that the mean thickness and standard deviation of the resistance layer after screen printing were about 32.2 and 2.4 μm, respectively. The mean and standard deviation of the bump were about 192 and 10.2 μm, respectively. The thicknesses of resistance and bump layers govern the deposited volume, which can be calculated using V = W × L × h, where W, L, and h are the structure width, length, and thickness, respectively. The shrinkage volumes of resistance and bump layers were about 6.61 % and 3.53 %, respectively, indicating that the high viscosity had smaller shrinkages.

3.3. Response Analyses

The characteristic outputs of dynamic response and contact force were measured using a digital force gauge (model HF-10, ALGOL, Japan) with an accuracy of 0.1 N and a cylinder tip with a radius of 0.5 mm, a 6 axis micro-stage, an LCR meter, and a motor controller with a displacement accuracy of 1 μm.

3.3.1. Bump Structure Effects

For dynamic response measurement, a trapezoid force with a maximum force of 5 N, parallel to the y-axis in the xy-plane, was applied to the elements. The sensing mechanism of the dynamic response is based on the impedance change of resistance after contact. When a force is applied on a bump and the organic resistance layer is compressed, the sensing electronics of the top and bottom conduct the impedance changes. The equivalent circuit of sensing impedance is similar to a variable resistor. Figure 8 shows the dynamic response of membranes without bumps, with bumps, and with bumps and a resistance layer. The transient response of membrane without bumps had a delay time after the pressing force was applied. Furthermore, the response took longer to reach steady-state, at about 1.56 voltages. PI film is an elastic polymer and has an over-damping response when force is applied. The membrane with bumps reached steady-state the fastest, having no delay. The steady-state value of the membrane with bumps and a resistance layer was higher than those of the others. The bump structure and a resistance layer on the top membrane improve the response of sensing sensitivity and increase the steady-state value. During the contact process of the membrane without bumps, the post structures resisted the touch force and reduced the membrane deformation deflections when a force was applied on the top membrane. However, the membrane with a bump structure had a protrusion for enhancing membrane deflections, and it looks like an inertial mass on the center of membrane. The inertial mass can provide an inertial force to enhance the membrane dynamic response when a force is applied or released.

3.3.2. Contact Force Measurement

For contact characteristic measurement, an external force, parallel to the y-axis in the xy-plane, was applied at the top center of the membrane. The displacements of the stages were adjusted to test the compression force versus the characteristic output at the operating frequency of 1 kHz, related to the measurement accuracy of sensing material, in ambient conditions, as shown in Figure 9(a). The symbols P1 to P5 indicate the measurement points at the center and 4 apexes of the array sensor, respectively. Results show that the impedance values sharply decreased with increasing compression force. The characteristic trend of the resistance material after fabricating was similar at the different measurement points. The characteristic output versus compression forces can approximate to linear logarithm regression. Therefore, for multi-touch switch sensing, the thresholds of the resistance response were determined according to the compression forces.
The effects of temperature variations from 5 to 95°C on different structures for switch scanning are shown in Figure 9(b). A constant force of 15 N was applied to measure the steady-state response. The responses with about 0.12 % error were transformed into sensing forces. Results show that the steady-state response slightly decreased with increasing temperature. We conclude that resistance layer became softer and had a lower resistance value at higher temperatures after a force was applied, which indicates that the resistive material has a negative temperature coefficient. However, this characteristic response can be used in multi-touch switching because the high and low signals were very clear after repeated touching at different temperatures. Although the responses at higher temperatures had small voltage changes, the multi-touch function is not influenced.

3.3.3. Performance Testing

The multi-touch testing of the flexible electronics sensors is shown in Figure 10(a). Five fingers were used to touch the flexible electronics sensor at the same time. The characteristic output of sensor was shown on a notebook screen. Blue blocks indicated untouched areas and yellow blocks indicated touched areas. The sensor can identify multi-touch operating that enables a user to interact with more than on finger at a time.
For the bending testing, flexible sensors were simply fixed on different curved surfaces of cylinder molds, with curvature radii of 3, 5, and 7 cm, to test the bending response. During experimental measurements, gap distances after differential bending were calculated using the principle of parallel capacitance, C = (ε ×A)/d. where A is the area of each plate, ε is the permittivity of free space, ε = 8.84 × 10-12 F/m, and d is the distance between the two substrates. The gap distance, at the radius of infinite curvature, is originally about 41 μm. The results of the bending tests at different curvature radii versus gap distance are shown in Figure 10(b). The gap distance at a curvature radius of 3 cm is about 27 um. However, a curvature radius of less than 1 cm easily generates erroneous signals because the small gap produces the pull-in effect. Thus, erroneous signals during the bending can be effectively eliminated when the curvature radius is over 3 cm. Moreover, the sensor was repeatedly tested using a periodic force with a digital force gauge and a motor controller. The characteristic response of the switch function was consistent after bending around a curvature radius of over 3 cm.

4. Conclusions

This study has successfully developed a flexible electronics sensor for multi-touch switch detection using an algorithm matrix and using screen printing technology for large-scale manufacturing. For printing thick structures, materials with higher viscosity can be used to print excellent morphological profiles, which can greatly reduce the dimension effects of diffusion and shrinkage, enhance the printing resolution, and decrease the cohesive force between the stencil mask and the sensor substrate. In addition, printed material on flexible substrates with a high surface roughness had good printed patterns and adhesive force. The gap within sensor structure provided a buffer distance to avoid erroneous contact during bending action. This sensor, with a minimum curvature radius of about 3 cm, is flexible enough to be applied anywhere without being damaged. We believe that the results of this study can be applied to many fields of flexible electronics sensors and that they provide useful information for designing and fabricating flexible large area devices.

Acknowledgments

The test facilities and resources used in this study were supported by the Ministry of Economic Affairs to fund environment construction projects of the Taiwanese government.

References and Notes

  1. Agarwal, A.; Izadi, S.; Chandraker, M.; Blake, A. High precision multi-touch sensing on surfaces using overhead cameras. Horizontal Interactive Human-Computer Systems, 2007. TABLETOP '07. Second Annual IEEE International Workshop on; 2007; 1, pp. 197–200. [Google Scholar]
  2. Hodges, S.; Izadi, S.; Butler, A.; Rrustemi, A.; Buxton, B. ThinSight: versatile multi-touch sensing for thin form-factor displays. Proceedings of the 20th Annual ACM Conference on User Interface Software and Technology, Rhode Island, USA, October 2007; pp. 259–268.
  3. Wilson, A.D. PlayAnywhere: A compact interactive tabletop projection-vision system. Proceedings of the 18th annual ACM symposium on User interface software and technology, Washington, USA; 2005; pp. 83–92. [Google Scholar]
  4. Malik, S.; Laszlo, J. Visual Touchpad: A two-handed gestural input device. Proceedings of the 6th International Conference on Multimodal interfaces, State College Pennsylvania, USA; 2004; pp. 289–296. [Google Scholar]
  5. Rekimoto, J. SmartSkin: An infrastructure for freehand manipulation on interactive surfaces. Proceedings of the SIGCHI conference on Human factors in computing systems: Changing our world, changing ourselves, Minnesota, USA; 2002; pp. 113–120. [Google Scholar]
  6. Han, J.Y. Low-Cost multi-touch sensing through frustrated total internal reflection. Proceedings of the 18th annual ACM symposium on User interface software and technology, Washington, USA; 2005; pp. 115–118. [Google Scholar]
  7. Jobs, S.P.; Forstall, S.; Christie, G.; Lemay, S.O.; Herz, S.; van Os, M.; Ording, B.; Novick, G.; Westerman, W.C.; Chaudhri, I.; Coffman, P.L.; Kocienda, K.; Ganatra, N.K.; Anzures, F.A.; Wyld, J.A.; Bush, J.; Matas, M.; Marcos, P.D.; Pisula, C.J.; King, V.S.; Blumenberg, C.; Tolmasky, F.R.; Williamson, R.; Boule, A.M.J.; Lamiraux, H.C. Touch screen device, method, and graphical user interface for determining commands by applying heuristics. Apple Inc. Patent, US7479949, 2009. [Google Scholar]
  8. Perski, H.; Morag, M. Dual function input device and method. N-trig Ltd. Patent, US6762752, 2004. [Google Scholar]
  9. Drucker, S.M.; Wong, C.G. Selectable projector and imaging modes of display table. Microsoft Corporation Patent, US7134756, 2006. [Google Scholar]
  10. Dietz, P.; Leigh, D. DiamondTouch: A Multi-User Touch Technology. Proceedings of the 14th annual ACM symposium on User interface software and technology, Orlando, Florida; 2001; pp. 219–226. [Google Scholar]
  11. Sekitan, T.; Takamiya, M.; Noguch, Y.; Nakano, S.; Kato, Y.; Sakurai, T.; Someya, T. A large-area wireless power-transmission sheet using printed organic transistors and plastic MEMS switches. Nat. Mater. 2007, 6, 413–417. [Google Scholar]
  12. Lungenschmied, C.; Dennler, G.; Neugebauer, H.; Sariciftci, S.N.; Glatthaar, M.; Meyer, T.; Meyer, A. Flexible, long-lived, large-area, organic solar cells. Solar Energy Mater. Solar Cells 2007, 91, 379–384. [Google Scholar]
  13. Street, R.A.; Wong, W.S.; Ready, S.E.; Chabinyc, M.L.; Arias, A.C.; Limb, S.; Salleo, A. Lujan R. Jet printing flexible displays. Materials Today 2006, 9, 32–37. [Google Scholar]
  14. Tehrani, P.; Isaksson, J.; Mammo, W.; Andersson, M.R.; Robinson, N.D.; Berggren, M. Evaluation of active materials designed for use in printable electrochromic polymer displays. Thin Solid Films 2006, 515, 2485–2492. [Google Scholar]
  15. Wong, W.S.; Lujan, R.; Daniel, J.H.; Limb, S. Digital lithography for large-area electronics on flexible substrates. J. Non-Cryst. Solids 2006, 352, 1981–1985. [Google Scholar]
  16. Seol, Y.G.; Lee, J.G.; Lee, N.E. Effects of different electroplated gate electrodes on electrical performances of flexible organic thin film transistor and flexibility improvement. Org. Electron. 2007, 8, 513–521. [Google Scholar]
  17. Ko, S.H.; Chung, J.; Pan, H.; Grigoropoulos, C.P.; Poulikakos, D. Fabrication of multilayer passive and active electric components on polymer using inkjet printing and low temperature laser processing. Sens. Actuat. A-Phys. 2007, 134, 161–168. [Google Scholar]
  18. Manunza, I.; Bonfiglio, A. Pressure sensing using a completely flexible organic transistor. Biosens. Bioelectron. 2007, 22, 2775–2779. [Google Scholar]
  19. Xiao, S.Y.; Che, L.F.; Li, X.X.; Wang, Y.L. A novel fabrication process of MEMS devices on polyimide flexible substrates. Microelectron. Eng. 2008, 85, 452–457. [Google Scholar]
  20. Tan, Z.; Shikida, M.; Hirota, M.; Xing, Y.; Sato, K.; Iwasaki, T.; Iriye, Y. Characteristics of on-wall in-tube flexible thermal flow sensor under radially asymmetric flow condition. Sens. Actuat. A-Phys. 2007, 138, 87–96. [Google Scholar]
  21. Su, P.G.; Wang, C.S. Novel flexible resistive-type humidity sensor. Sens. Actuat. B-Chem. 2007, 123, 1071–1076. [Google Scholar]
  22. Recart, F.; Freire, I.; Perez, L.; Aurrekoetxea, R.L.; Jimeno, J.C.; Bueno, G. Screen printed boron emitters for solar cells. Solar Energy Mater. Solar Cells 2007, 91, 897–902. [Google Scholar]
  23. Taylor, A.D.; Kim, E.Y.; Humes, V.P.; Kizuka, J.; Thompson, L.T. Inkjet printing of carbon supported platinum 3-D catalyst layers for use in fuel cells. J. Power Sources 2007, 171, 101–106. [Google Scholar]
  24. Sanaur, S.; Whalley, A.; Alameddine, B.; Carnes, M.; Nuckolls, C. Jet-printed electrodes and semiconducting oligomers for elaboration of organic thin-film transistors. Org. Electron. 2006, 7, 423–427. [Google Scholar]
  25. Katayama, T.; Hakotani, M.; Shinohara, M.; Nishii, K.; Tabuchi, H. Effect of material internal pressure in curing process of SMC roll forming. J. Mater. Process. Technol. 2004, 155, 1577–1582. [Google Scholar]
  26. Xu, Y.; Jiang, F.; Newbern, S.; Huang, A.; Ho, C.M.; Tai, Y.C. Flexible shear-stress sensor skin and its application to unmanned aerial vehicles. Sens. Actuat. A-Phys. 2003, 105, 321–329. [Google Scholar]
  27. Kim, Y.S. Microheater-integrated single gas sensor array chip fabricated on flexible polyimide substrate. Sens. Actuat. B-Chem. 2006, 114, 410–417. [Google Scholar]
  28. Chang, W.Y.; Fang, T.H.; Lin, Y.C. Characterization and fabrication of wireless flexible physiological monitor sensor. Sens. Actuat. A-Phys. 2008, 143, 196–203. [Google Scholar]
  29. Chang, W.Y.; Fang, T.H.; Lin, Y.C. Physical characteristics of polyimide films for flexible sensors. Appl. Phys. A-Mat. Sci. Process. 2008, 92, 693–701. [Google Scholar]
  30. Vinson, J. R. The behavior of thin walled structures: beams, paltes and shells; Kluwer Academic Publishers: Dordrecht, The Netherlands, 1989; pp. 9–18. [Google Scholar]
  31. Chouaf, A.; Malhaire, C.; Berre, M.L.; Dupeux, M.; Pourroy, F.; Barbier, D. Stress analysis at singular points of micromachined silicon membrane. Sens. Actuat. A-Phys. 2000, 84, 109–115. [Google Scholar]
Figure 1. Fabrication procedures of flexible electronics sensors for large area manufacturing using screen printing technology.
Figure 1. Fabrication procedures of flexible electronics sensors for large area manufacturing using screen printing technology.
Sensors 09 01188f1
Figure 2. Schematic circuit of a flexible array sensor for use in multi-touch sensing applications, (a) Control system frame, and (b) the equivalent circuit of row 1 when columns inputs are 1,0, …, 0.
Figure 2. Schematic circuit of a flexible array sensor for use in multi-touch sensing applications, (a) Control system frame, and (b) the equivalent circuit of row 1 when columns inputs are 1,0, …, 0.
Sensors 09 01188f2
Figure 3. Membrane mechanical deflection of a flexible electronics sensor when a load was applied.
Figure 3. Membrane mechanical deflection of a flexible electronics sensor when a load was applied.
Sensors 09 01188f3
Figure 4. Comparison of the structural characteristics. (a) The effects of membranes without bumps, with bumps, and with bumps and a resistance layer, and (b) the effects of bump widths and thicknesses of 100, 250, and 500 μm.
Figure 4. Comparison of the structural characteristics. (a) The effects of membranes without bumps, with bumps, and with bumps and a resistance layer, and (b) the effects of bump widths and thicknesses of 100, 250, and 500 μm.
Sensors 09 01188f4
Figure 5. Simulation of the optimal pixel dimensions of the flexible electronics sensor at a constant force of 5 N. (a) Deflection and (b) stress distribution of a membrane with bumps, and (c) deflection and (d) stress distribution of a membrane with bumps and a resistance layer.
Figure 5. Simulation of the optimal pixel dimensions of the flexible electronics sensor at a constant force of 5 N. (a) Deflection and (b) stress distribution of a membrane with bumps, and (c) deflection and (d) stress distribution of a membrane with bumps and a resistance layer.
Sensors 09 01188f5
Figure 6. Array sensors of flexible electronics based on polyimide films for large area sensing. (a) Inside view between two PI films, including a resistance layer, posts, and electrodes, and (b) the bump structures on the top film after screen printing.
Figure 6. Array sensors of flexible electronics based on polyimide films for large area sensing. (a) Inside view between two PI films, including a resistance layer, posts, and electrodes, and (b) the bump structures on the top film after screen printing.
Sensors 09 01188f6
Figure 7. The printing diffusion ratios of the bump and resistance materials compared with original width. X and Y are parallel to and perpendicular to the printing directions, respectively.
Figure 7. The printing diffusion ratios of the bump and resistance materials compared with original width. X and Y are parallel to and perpendicular to the printing directions, respectively.
Sensors 09 01188f7
Figure 8. Comparison of the dynamic response effects of the membrane without bump, with bumps, and with bumps and a resistance layer.
Figure 8. Comparison of the dynamic response effects of the membrane without bump, with bumps, and with bumps and a resistance layer.
Sensors 09 01188f8
Figure 9. Characteristics output of flexible electronics sensors. (a) Voltage versus force at an operating frequency of 1 kHz at various pixels, and (b) steady-state output voltage response of the membrane with a bump and with bump and resistance layers at various temperatures.
Figure 9. Characteristics output of flexible electronics sensors. (a) Voltage versus force at an operating frequency of 1 kHz at various pixels, and (b) steady-state output voltage response of the membrane with a bump and with bump and resistance layers at various temperatures.
Sensors 09 01188f9
Figure 10. Performance testing, (a) Fingers used as input units to test multi-touch using the sensing algorithm matrix, and (b) bending testing at different curvature radii of 1, 3, 5, 7, and inf. cm.
Figure 10. Performance testing, (a) Fingers used as input units to test multi-touch using the sensing algorithm matrix, and (b) bending testing at different curvature radii of 1, 3, 5, 7, and inf. cm.
Sensors 09 01188f10
Table 1. Comparison of multi-touch characteristics.
Table 1. Comparison of multi-touch characteristics.
ItemThinSight [2]Jeff Han [6]Apple [7]Microsoft surface [9]Diamond Touch [10]This work
SensingLED emitters and detectorsInfrared light and CameraMutual capacitance and force-sensingInfrared and projectorAntenna and projectorOrganic resistance

TechnologyDigital I/O driving and Standard bicubic interpolationFrustrated total internal reflectionProjected capacitive technologyDigital light processing technologyTransmitting technologyAlgorithm matrix operating

ControllerMicrocontroller and PCBulky equipmentMicrocontrollerBulky equipmentcomputerMicrocontroller

SurfaceAcrylicAcrylic paneGlass substrateAcrylic screenFiber glassPolyimide

FlexibleDifficultDifficultDifficultDifficultDifficultFeasible

SensorEmbeddingEmbeddingEmbeddingEmbedding-Screen printing

CostMediumMediumMediumHighHighLow

Share and Cite

MDPI and ACS Style

Chang, W.-Y.; Fang, T.-H.; Yeh, S.-H.; Lin, Y.-C. Flexible Electronics Sensors for Tactile Multi-Touching. Sensors 2009, 9, 1188-1203. https://doi.org/10.3390/s9021188

AMA Style

Chang W-Y, Fang T-H, Yeh S-H, Lin Y-C. Flexible Electronics Sensors for Tactile Multi-Touching. Sensors. 2009; 9(2):1188-1203. https://doi.org/10.3390/s9021188

Chicago/Turabian Style

Chang, Wen-Yang, Te-Hua Fang, Shao-Hsing Yeh, and Yu-Cheng Lin. 2009. "Flexible Electronics Sensors for Tactile Multi-Touching" Sensors 9, no. 2: 1188-1203. https://doi.org/10.3390/s9021188

Article Metrics

Back to TopTop