Next Article in Journal
Experimental Research and Control Strategy of Pumped Storage Units Dispatching in the Taiwan Power System Considering Transmission Line Limits
Previous Article in Journal
Modeling Future Life-Cycle Greenhouse Gas Emissions and Environmental Impacts of Electricity Supplies in Brazil
 
 
Font Type:
Arial Georgia Verdana
Font Size:
Aa Aa Aa
Line Spacing:
Column Width:
Background:
Article

Analysis and Experiment of a Novel Brushless Double Rotor Machine for Power-Split Hybrid Electrical Vehicle Applications

Department of Electrical Engineering, Harbin Institute of Technology, Harbin 150080, China
*
Author to whom correspondence should be addressed.
Energies 2013, 6(7), 3209-3223; https://doi.org/10.3390/en6073209
Submission received: 27 March 2013 / Revised: 20 June 2013 / Accepted: 21 June 2013 / Published: 2 July 2013

Abstract

:
A novel brushless double rotor machine (BDRM) is proposed in this paper. The BDRM is an important component in the brushless compound-structure permanent-magnet synchronous machine (CS-PMSM) system, which is a promising technology for power-split hybrid electric vehicle (HEV) applications. Compared with common double rotor machines, the brushes and slip rings required by rotating winding have been omitted in the BDRM, thus there are no such problems as maintenance, friction losses and so forth. Firstly, the torque characteristics of the BDRM are analyzed. As the stator has ring-shaped centralized windings, the size characteristics of the BDRM are different from those of conventional machines. The new sizing and torque equations are analyzed and the theoretical results are applied to determine the main dimensions. Additionally, studies of the analytical magnetic circuit and finite element method (FEM) model show that the BDRM tends to have high leakage flux and low power factor. Although the scope for improving the serious flux leakage of the BDRM is limited by the special magnetic topology, a method to obtain higher power factor is provided. Finally, a 10 kW prototype machine was manufactured, assembly of the prototype is discussed in detail and experimental tests are performed to validate the analytical and simulation results.

Graphical Abstract

1. Introduction

In recent years, a new power-split hybrid system called compound-structure permanent-magnet synchronous machine (CS-PMSM) system has been developed, aiming to get rid of the mechanical planetary gear while retaining the continuously variable transmission (CVT) function [1,2,3,4]. CS-PMSMs can replace the gearbox, flywheel, clutch, starting motor and generator used in traditional automobiles. Moreover, in a hybrid system equipped with the BDRM, the engine only provides average power of the vehicle, so its size will be smaller than that in traditional automobiles. However, brushes and slip rings are a short board in the existing topology of CS-PMSM [5,6,7,8]. To solve this problem, a novel brushless CS-PMSM that consists of one brushless double rotor machine (BDRM) and one conventional machine (CM) is proposed, as shown in Figure 1.
Figure 1. Novel brushless CS-PMSM system.
Figure 1. Novel brushless CS-PMSM system.
Energies 06 03209 g001
As the key part of the brushless CS-PMSM system, the BDRM implements brushless technology for a double rotor machine. There have been several proposals for double rotor machines in the past. Fan and Wen [6] have proposed a brushless permanent magnet dual mechanical port machine (BLDMPM) for HEV use. This machine uses the claw pole structure and is based on the principle of a disc type electric machine. Due to the special teeth-pole pattern in BLDMPM, its torque has a strong pulsation component. Moreover, Zheng [9] has presented a radial magnetic-field-modulated brushless double-rotor machine (MFM-BDRM). It is based on the principle of magnetic field modulation. The MFM-BDRM is a promising technology for HEV drive systems, but there are still some problems to be solved in the prototyping. Compared with other proposals of double rotor machines, some advantages of the BDRM can be summarized as follows:
(1)
BDRM’s windings are mounted on the stator which is close to the motor case, so the windings have good heat dissipation;
(2)
There is no coupling between the stator phases, so the BDRM can be easily designed to be a multiphase structure;
(3)
It is appropriate that the BDRM is designed to be a multi-pole machine, so the BDRM is suitable for intermediate or high frequency operation;
(4)
BDRM’s ring shaped windings are simple and the stator processing is convenient.
In this paper, the torque characteristics and power factor of the BDRM are investigated. Based on the analysis results, a prototype was manufactured and the experimental results provided.

2. Structure and Operating Principle

Figure 2 shows the exploded view of the BDRM. It is a synchronous machine with a stator, claw-pole outer rotor and permanent-magnet inner rotor. The stator comprises laminated iron cores and ring-shaped windings, as shown in Figure 2a. The claw-pole rotor has three arrays of claws placed in non-magnetic bracket as shown in Figure 2b. Figure 2c shows the permanent-magnet rotor which is built in a flux-concentrated magnet topology.
Figure 2. Exploded view of the BDRM: (a) stator; (b) claw-pole rotor; (c) permanent-magnet rotor.
Figure 2. Exploded view of the BDRM: (a) stator; (b) claw-pole rotor; (c) permanent-magnet rotor.
Energies 06 03209 g002
The flux path in one pole of the BDRM is shown in Figure 3. The flux from the magnet goes radially through the inner air gap into one claw, then across the outer air gap and into the stator, passing axially along the yoke, and once again radially passing the outer air gap into the next claw, and finally returns to the opposite polarity of the magnet, completing a flux loop.
Brushless technology for a double-rotor machine is realized, which makes the BDRM a meaningful invention. When used in hybrid electric vehicle traction, the permanent-magnet rotor is connected to the crank shaft of the internal combustion engine (ICE), while the claw-pole rotor is connected to the final drive. The function of permanent-magnet rotor is to transfer the torque of the ICE to claw-pole rotor with the assistance of the stator. When stator windings are electrified with different frequencies (via inverter), the speed adjustment between claw-pole rotor and permanent-magnet rotor can be realized.
The claw-pole rotor is connected to load shaft together with the CM, as shown in Figure 1. Without considering the static friction, the speed and torque equations on the outgoing shaft are shown as follows:
ω l = ω c
T o u t = T B D R M + T C M
where ω c , ω l are the mechanical angular speeds of the claw-pole rotor and the load; TCM is the torque of the CM, which can be positive and negative, depending on the torque difference between the ICE and output demand; and TBDRM is the torque of the BDRM.
It can be seen from Equation (2) that the output torque of the shaft comprises the torque of the BDRM and the torque of the CM. By controlling the torque provided by CM, the engine torque can be regulated for high efficiency operation independent of load torque.
Figure 3. Flux path in one pole of the BDRM.
Figure 3. Flux path in one pole of the BDRM.
Energies 06 03209 g003

3. Parametric Influences on Electromagnetic Torque

As the stator has ring-shaped centralized windings, a new definition of electric loading is given as the current sum per axial armature length:
A = N I l e f
where N is the number of stator-coil turns; I is its current value; lef is the effective axial length of single-phase BDRM.
Then the back electromotive force (BEMF) can be calculated by:
E = 2 π f N k w p Φ
where f is the frequency of the stator winding current (Hz); kw is the winding factor; p is the pole-pair number; Φ is the main flux from each pole (Wb).
The electromagnetic torque could be expressed as:
T e = 2 π m f N k w p Φ J S c cos ψ / Ω s
where m is the phase number; J is the current density (A/m2); Sc is the cross-sectional area of the conductor (m2); ψ is the leading angle of load current I to no-load BEMF E0; Ωs is the synchronous angular speed (rad/s).
The BDRM has homopolar flux in the stator cores. This allows an increase in the electromagnetic torque with an increase in the pole-pair number for given geometrical dimensions and current loading. However, the electrical frequency also increases with pole-pair number, which will lead to excessive core loss [10,11]. The 3D finite element method (FEM) was carried out to compute the average torque and the core loss. Figure 4 shows the no-load flux density distribution of one model at maximum linked flux. Figure 5 shows the variation of average torque and core loss versus the pole-pair number, these models are built with the same dimensions. A compromise between the output torque and the core loss has been made, and the pole-pair number is chosen as six.
Figure 4. No-load flux density distribution at maximum linked flux.
Figure 4. No-load flux density distribution at maximum linked flux.
Energies 06 03209 g004
Figure 5. Variation of BDRM’s performance versus the pole-pair number: (a) average torque; (b) core loss.
Figure 5. Variation of BDRM’s performance versus the pole-pair number: (a) average torque; (b) core loss.
Energies 06 03209 g005

4. Power Factor Improvement

Results from analytical and FEM calculations show that the power factor of BDRM is low [12]. This results from the special configuration of BDRM, which causes serious leakage flux in the magnetic circuit. A phasor diagram of the BDRM is shown in Figure 6, where E0 and Eδ are the fundamental BEMF in no-load and load operation; Id, Iq are the d- and q-axis armature currents; R1 is the armature resistance; U is the voltage fed by external circuit; Xd, Xq are the d- and q-axis synchronous reactance and φ is the power factor angle.
When Id = 0, neglecting the small voltage drop across phase resistance, the power factor could be expressed as [12]:
cos φ = E 0 E 0 2 + ( X q I q ) 2
The no-load BEMF is proportional to the frequency, the number of coils and the main flux from the PM, and it could be expressed as:
E 0 = k 1 N f Φ m
where k1 is the scale coefficient; Φ m is the total main flux from the PM.
Figure 6. Phasor diagram of the BDRM when Id ≠ 0.
Figure 6. Phasor diagram of the BDRM when Id ≠ 0.
Energies 06 03209 g006
The q-axis synchronous reactance is proportional to the frequency, q-axis permeance, and the square of the numbers of coils, and it could be expressed as:
X q = k 2 N 2 f ( Λ 1 + Λ σ ) = k 2 N 2 f σ Λ 1
where k2 is the scale coefficient; Λ 1 is the main permeance; Λ σ is the leakage permeance; σ is the leakage coefficient.
Bring Equations (7) and (8) into Equation (6), the power factor can be expressed as:
cos φ = k 1 Φ m k 1 2 Φ m 2 + ( k 2 N σ Λ 1 I q ) 2 = 1 1 + ( k 2 N σ Λ 1 I q k 1 Φ m ) 2
Equation (9) presents the basic factors affecting the power factor. When the main flux Φm from the PM is increased, the power factor will be increased. Moreover, when the number of coils or the armature current is increased, the power factor will be decreased.
The distribution of magnetic field caused by PM and stator windings is analyzed, respectively, and the best match ratio between them is obtained. Figure 7 shows the variation of power factor and average torque versus the amount of PM and winding turns. In Figure 7, the average torque is obtained from the torque curve according to the FEM simulation. From Figure 7, it could be concluded that increasing thickness of the PM is an efficient way to improve the power factor and enhance torque density at the same time.
Figure 7. The parametric influences on power factor and average torque. (a) thickness of the PM; (b) winding turns in series per phase.
Figure 7. The parametric influences on power factor and average torque. (a) thickness of the PM; (b) winding turns in series per phase.
Energies 06 03209 g007
Although decreasing the stator current will increase the power factor, the torque output will obviously fall at the same time [13,14], and this is clearly not attractive in practice. The effective approach is to change the phase of stator current. By using vector control method in the inverter, the phase angle of the stator current can be adjusted. According to the phasor diagram, neglecting the small voltage drop across phase resistance, the power factor angle could be expressed as:
φ = arctan X q I q E 0 X d I d ψ
Then the power factor could be expressed as:
cos φ = cos ( arctan ω L q I cos ψ E 0 ω L d I sin ψ ψ )
where Ld; Lq are the d- and q-axis inductance; ω is the radian frequency.
The angle ψ depends on the phase angle of the input current from the inverter. It can be seen from Equation (11) that when the phase angle of the input current from the inverter is changed, different power factors will result. Under different amplitude and phase angle of stator current, E0, d-axis and q-axis inductance can be calculated by employing FEM, and then the power factor can be obtained from analytical calculation according to Equation (11). The variation of power factor versus ψ is shown in Figure 8. It can be seen that, for a fixed current value, the power factor will always reach its maximum value at a positive torque angle. Therefore, the power factor improvement can be realized by advancing the current phasor.
The average torque versus ψ (i.e., current angle leading the BEMF) is calculated when the rms value of the current is 35 A, as shown in Figure 9. There is only a slight decrease of the average torque value with the increase of the inner power factor angle when the inner power factor angle is small (0°~20°), so when the flux weakening mode is used, the proportion of the d-axis current should not be too large.
Figure 8. Variation of power factor versus ψ under different stator current conditions.
Figure 8. Variation of power factor versus ψ under different stator current conditions.
Energies 06 03209 g008
Figure 9. Torque versus ψ when rms value of the current is 35 A.
Figure 9. Torque versus ψ when rms value of the current is 35 A.
Energies 06 03209 g009

5. Construction of the Prototype

A BDRM prototype dimensioned for 10 kW has been manufactured and its major geometrical parameters are listed in Table 1.
Table 1. Geometrical parameters of the BDRM prototype.
Table 1. Geometrical parameters of the BDRM prototype.
ParametersValueParametersValue
Phase number3Length of the PM (mm)66
Pole-pair number6Width of the PM (mm)24
Stator outer diameter (mm)200Thickness of the PM (mm)8
Axial length of BDRM (mm)132Pole arc coefficient of the claw tip0.7
Outer air gap length (mm)0.8Pole arc coefficient of the claw root0.7
Inner air gap length (mm)0.8Thickness of the claw tip (mm)4.8
Winding turns in series per phase46Thickness of the claw root (mm)15.4
Number of slots3Shaft diameter of PM rotor (mm)48
The manufacturing process of the 3-phase stator is illustrated in Figure 10. Each phase consists of laminated iron cores and one concentrated ring-shaped coil. An automatic winding machine is used to inlay the coils of stator winding into the coil slots. The results of the measurements show that a slot fill factor of about 0.78 is obtained.
Figure 10. Manufacturing process of the 3-phase stator. (a) winding coils between the stator teeth; (b) installing the stator yoke.
Figure 10. Manufacturing process of the 3-phase stator. (a) winding coils between the stator teeth; (b) installing the stator yoke.
Energies 06 03209 g010
Difficulties were experienced in providing a tight fit between the claws and the non-magnetic bracket. A variety of methods have been tried and an effective solution obtained. As shown in Figure 11a, the claws are built-up by silicon-iron laminations with two small holes. The hollow cylindrical bracket is made of non-magnetic stainless steel with several narrow slots on the surface as shown in Figure 11b. The claws are firstly assembled by inserting a thin stainless steel rod into each hole, and then the claws are fixed on the non-magnetic bracket by welding these rods on the narrow slots. The assembled claw-pole rotor is shown in Figure 12a, then it is further secured by means of epoxy resin casting as shown in Figure 12b.
Figure 11. Components of the claw-pole rotor: (a) the claws; (b) the non-magnetic bracket.
Figure 11. Components of the claw-pole rotor: (a) the claws; (b) the non-magnetic bracket.
Energies 06 03209 g011
According to previous studies, the permanent-magnet rotor uses the tangential embedding rotor structure [15]. This structure can achieve the effect of flux-concentration, which can effectively improve the torque density of the BDRM. The magnets are grade N40 sintered NdFeB PMs and are rectangularly shaped with dimensions: 66 mm × 24 mm × 8 mm. Figure 13 shows the assembled rotor core before the PMs are installed.
Figure 12. Claw-pole rotor (a) before epoxy resin casting; (b) after epoxy resin casting.
Figure 12. Claw-pole rotor (a) before epoxy resin casting; (b) after epoxy resin casting.
Energies 06 03209 g012
Figure 13. Permanent-magnet rotor core.
Figure 13. Permanent-magnet rotor core.
Energies 06 03209 g013

6. Performance of the Prototype

Some measurements were performed upon the prototype. In the first step of the measurements, the BDRM is tested as a conventional single-rotor machine, and in the second step, the BDRM will be tested by connecting two machines on both two rotors to simulate the operation modes of the HEV system. The test bench of the first step is shown in Figure 14. The permanent-magnet rotor is connected with a synchronous machine on the left side, and the claw-pole rotor is fixed by a snap ring on the right side.
Figure 14. Test bench of the BDRM.
Figure 14. Test bench of the BDRM.
Energies 06 03209 g014
The tested no-load phase BEMFs at a rated speed of 2800 rpm are shown in Figure 15. Due to the end effect, the BEMF of B-phase is a little higher than those of the other two phases. The low harmonic content is apparent from the sinusoidal shape of the waveforms.
Figure 15. Tested no-load phase BEMFs at rated speed of 2800 rpm.
Figure 15. Tested no-load phase BEMFs at rated speed of 2800 rpm.
Energies 06 03209 g015
Tested and simulated no-load A-phase BEMFs at different speeds are compared in Figure 16. It can be seen that the tested and simulated rms values are in good agreement.
Figure 16. Tested and simulated no-load A-phase BEMFs at different speeds.
Figure 16. Tested and simulated no-load A-phase BEMFs at different speeds.
Energies 06 03209 g016
The accurate measurement of cogging torque and torque ripple is helpful in performance evaluation and further optimization of the BDRM. The cogging torque values between permanent magnetic rotor and the claw pole rotor is shown in Table 2. It can be seen that tested peak-peak value of cogging torque is about 1.9 Nm, which is higher than conventional PM machines.
Table 2. Tested and simulated cogging torque between PM rotor and claw pole rotor.
Table 2. Tested and simulated cogging torque between PM rotor and claw pole rotor.
TorqueTestedSimulated
Peak-peak value of cogging torque (Nm)1.92.1
Periodic numbers of cogging torque in one cycle1212
The load torque is tested at the speed of 800 rpm, as shown in Figure 17. The average torque is 26.1 Nm and the torque ripple is about 5.4%, which is also higher than that of conventional PM machines. The high cogging torque and torque ripple are mainly caused by the large air gaps between the claws. As torque ripple of the ICE is much higher than electric machines, torque ripple of the BDRM is considered acceptable for HEV applications.
Figure 17. Tested load torque at the speed of 800 rpm.
Figure 17. Tested load torque at the speed of 800 rpm.
Energies 06 03209 g017
Furthermore, the no-load loss has been measured. In no-load tests, two rotors of the prototype are dragged to rotate at different speeds. Then the no-load loss is the difference of the mechanical power measured from the two shafts:
P f w = P s 1 P s 2
where Ps1, Ps2 are the mechanical power measured from the two shafts; Pfw is the no-load loss of the BDRM.
During the test, it is found that torque of the two shafts is basically the same, so the no-load torque of the BDRM can be measured from either of the two shafts. Then the equation of the no-load loss can be represented as:
P f w = T Ω s 1 T Ω s 2
where Ωs1, Ωs2 are the mechanical speed of the two shafts; and T is the no-load torque of the BDRM.
The loss is investigated when the machine is operating in generator mode up to rated speed. However, a considerable braking torque is detected and the no-load loss is extremely high as shown in Figure 18.
Figure 18. Variation of average torque and no-load loss versus the shaft speed.
Figure 18. Variation of average torque and no-load loss versus the shaft speed.
Energies 06 03209 g018
An investigation led to the identification of one manufacturing defect mainly related to this phenomenon. This is the existence of a conductive bracket in the claw-pole rotor. The eddy current loss of the bracket has been estimated with the aid of 3D FEM simulation [16,17]. As shown in Figure 19, the eddy current loss is approximately 8 kW at rated speed, and this could contribute up to 73% of the whole loss. Simulation results verified that even if the bracket is built using a non-magnetic metrical, its conductive properties will result in significant eddy current loss.
Figure 19. Simulated eddy current loss of the bracket at rated speed.
Figure 19. Simulated eddy current loss of the bracket at rated speed.
Energies 06 03209 g019
The bracket fault has unfortunately delayed the test program, so there are no results from tests of the BDRM in different HEV operation modes to be presented in this paper. The improvement of the prototype will be undertaken and disseminated in future publications.

7. Conclusions

In this paper, an analysis procedure for a novel BDRM having three dimensional flux paths has been provided. Its unique torque characteristics are analyzed and the results show that the torque density can be increased by appropriately increasing the pole-pair number. Additionally, two methods are applied to improve the low power factor of the BDRM: one is to increase the thickness of the PM, and the other is to advance the current phasor. Finally, a prototype was constructed and tested. Measurements show that the no-load BEMFs are sinusoidal and show good agreement with calculated values, however, the measured no-load loss and braking torque are not within the expected range. This problem is caused by high eddy current loss in the conductive bracket. Future work will include the assembly of the claw-pole rotor with a non-conductive bracket to prevent the eddy currents.

Acknowledgments

This work was supported in part by National Natural Science Foundation of China under Project 51077026, and in part by the 863 Plan of China under Project 2011AA11A261.

Conflict of Interest

The authors declare no conflict of interest.

References

  1. Nordlund, E.; Sadarangani, C. The four-Quadrant Energy Transducer. In Proceedings of 37th ISA Annual Meeting Conference, Pittsburgh, PA, USA, 13–18 October 2002; pp. 390–397.
  2. Xu, L.Y. Breed of Electrical Machine-Basic Analysis and Applications of Dual Mechanical Port Electric Machines. In Proceedings of 8th International Conference on Electrical Machines and Systems, Nanjing, China, 27–29 September 2005; pp. 25–31.
  3. Eriksson, S.; Sadarangani, C. A Four-Quadrant HEV Drive System. In Proceedings of VTC-Fall IEEE 56th Vehicular Technology Conference, Vancouver, Canada, 24–28 September 2002; pp. 1510–1514.
  4. Cheng, Y.; Cui, S.M.; Song, L.W.; Chan, C.C. The study of the operation modes and control strategies of an advanced electromechanical converter for automobiles. IEEE Trans. Magn. 2007, 43, 430–433. [Google Scholar] [CrossRef]
  5. Liu, R.R.; Zheng, P.; Zhao, H.; Sadarangani, C. Investigation of a Compound-Structure Permanent-Magnet Synchronous Machine Used for HEVs. In Proceedings of IEEE Vehicle Power and Propulsion Conference, Harbin, China, 3–5 September 2008; pp. 1–5.
  6. Fan, T.; Wen, X.H.; Xue, S.; Kong, L. A Brushless Permanent Magnet Dual Mechanical Port Machine for Hybrid Electric Vehicle Application. In Proceedings of International Conference on Electrical Machines and Systems (ICEMS 2008), Wuhan, China, 17–20 October 2008; pp. 3604–3607.
  7. Nordlund, E.; Eriksson, S. Test and Verification of a Four-Quadrant Transducer for HEV Applications. In Proceedings of IEEE Vehicle Power and Propulsion Conference, Chicago, IL, USA, 7–10 September 2005; pp. 37–41.
  8. Sun, X.; Cheng, M.; Hua, W.; Xu, L. Optimal design of double-layer permanent magnet dual mechanical port machine for wind power application. IEEE Trans. Magn. 2009, 45, 4613–4616. [Google Scholar] [CrossRef]
  9. Zheng, P.; Bai, J.G.; Tong, C.D.; Lin, J.; Wang, H.P. Research on Electromagnetic Performance of a Novel Radial Magnetic-Field-Modulated Brushless Double-Rotor Machine. In Proceedings of International Conference on Electrical Machines and Systems, Beijing, China, 20–23 August 2011; pp. 1–6.
  10. Huang, Y.K.; Zhu, J.G.; Guo, Y.G.; Lin, Z.W.; Hu, Q.S. Design and analysis of a high-speed claw pole motor with soft magnetic composite core. IEEE Trans. Magn. 2007, 43, 2492–2494. [Google Scholar] [CrossRef]
  11. Zhang, F.G.; Bai, H.J.; Zhang, S.F.; Gruenberger, H.P.; Nolle, E. Electromagnetism Model and Characteristic Simulation of Novel Claw Pole Generator with Permanent Magnet Outer Rotor. In Proceedings of the International Power Electronics and Motion Control Conference, Shanghai, China, 14–16 August 2007; pp. 219–223.
  12. Zheng, P.; Wu, Q.; Zhao, J.; Tong, C.D.; Bai, J.G.; Zhao, Q.B. Performance analysis and simulation of a novel brushless double rotor machine for power-split HEV applications. Energies 2012, 5, 119–137. [Google Scholar] [CrossRef]
  13. Lee, S.H.; Kwon, S.O.; Lee, J.J.; Hong, J.P. Characteristic analysis of claw-pole machine using improved equivalent magnetic circuit. IEEE Trans. Magn. 2009, 45, 4570–4573. [Google Scholar] [CrossRef]
  14. Zhu, J.G.; Guo, Y.G.; Lin, Z.W.; Li, Y.J.; Huang, Y.K. Development of PM transverse flux motors with soft magnetic composite cores. IEEE Trans. Magn. 2011, 47, 4376–4383. [Google Scholar] [CrossRef]
  15. Zheng, P.; Wu, Q.; Zhao, J.; Tong, C.D.; Bai, J.G.; Zhao, Q.B. Performance analysis and simulation of a novel brushless double rotor machine for power-split HEV applications. Energies 2012, 5, 119–137. [Google Scholar] [CrossRef]
  16. Guo, Y.G.; Zhu, J.G.; Zhong, J.J.; Wu, W. Core losses in claw pole permanent magnet machines with soft magnetic composite stators. IEEE Trans. Magn. 2003, 39, 3199–3201. [Google Scholar] [CrossRef]
  17. Zhang, F.G.; Liu, Y.; Bai, H.J. Study and Design of 3-D Flux Permanent Magnet Claw-Pole Motor with SMC Stator. In Proceedings of International Conference on Applied Superconductivity and Electromagnetic Devices, Chengdu, China, 25–27 September 2009; pp. 316–319.

Share and Cite

MDPI and ACS Style

Zheng, P.; Wu, Q.; Bai, J.; Tong, C.; Song, Z. Analysis and Experiment of a Novel Brushless Double Rotor Machine for Power-Split Hybrid Electrical Vehicle Applications. Energies 2013, 6, 3209-3223. https://doi.org/10.3390/en6073209

AMA Style

Zheng P, Wu Q, Bai J, Tong C, Song Z. Analysis and Experiment of a Novel Brushless Double Rotor Machine for Power-Split Hybrid Electrical Vehicle Applications. Energies. 2013; 6(7):3209-3223. https://doi.org/10.3390/en6073209

Chicago/Turabian Style

Zheng, Ping, Qian Wu, Jingang Bai, Chengde Tong, and Zhiyi Song. 2013. "Analysis and Experiment of a Novel Brushless Double Rotor Machine for Power-Split Hybrid Electrical Vehicle Applications" Energies 6, no. 7: 3209-3223. https://doi.org/10.3390/en6073209

Article Metrics

Back to TopTop