Next Article in Journal
Influence of Substituent Chain Branching on the Transfection Efficacy of Cyclopropenium-Based Polymers
Previous Article in Journal
Synthesis, Property Characterization and Photocatalytic Activity of the Polyaniline/BiYTi2O7 Polymer Composite
 
 
Font Type:
Arial Georgia Verdana
Font Size:
Aa Aa Aa
Line Spacing:
Column Width:
Background:
Article

Correlation of Microstructure, Rheological and Morphological Characteristics of Synthesized Polypropylene (PP) Reactor Blends Using Homogeneous Binary Metallocene Catalyst

by
Javid Vaezi
1,2,
Mehdi Nekoomanesh
1,
Hossein Ali Khonakdar
1,3,*,
Seyed Hassan Jafari
4 and
Alireza Mojarrad
5
1
Iran Polymer and Petrochemical Institute (IPPI), P.O. Box 14965/115 Tehran, Iran
2
National Petrochemical Company, Petrochemical Research and Technology Company (NPC-RT), P.O. Box 1435884711 Tehran, Iran
3
Leibniz Institute of Polymer Research, D-01067 Dresden, Germany
4
School of Chemical Engineering, College of Engineering, University of Tehran, P.O. Box 11155-4563 Tehran, Iran
5
Department of Chemical Engineering, Faculty of Engineering, Shiraz Branch, Islamic Azad University, P.O. Box 71993-3 Shiraz, Iran
*
Author to whom correspondence should be addressed.
Polymers 2017, 9(3), 75; https://doi.org/10.3390/polym9030075
Submission received: 14 January 2017 / Revised: 7 February 2017 / Accepted: 16 February 2017 / Published: 24 February 2017

Abstract

:
A novel binary homogeneous catalyst system based on (I): rac-Me2Si(2-Me-4-PhIn)2ZrCl2 and (II): (2-PhIn)2ZrCl2 catalysts at various molar ratios was utilized for the synthesis of polypropylene (PP) reactor blends with bimodal molecular weight distribution (MWD). The results of gel permeation chromatography analyses revealed that the catalyst (I) was responsible for the production of i-PP with high molecular weight (MW) while the individual use of catalyst (II) led to the production of an elastomeric PP with relatively low MW. However, application of the binary catalyst system led to high MW bimodal MWD products being highly dependent on the catalysts’ molar ratios. Increasing the molar ratio of catalyst (II) to catalyst (I) resulted in a notable enhancement of the products’ complex viscosity due to the increased MW, a higher level of chains’ entanglements and formation of amorphous blocks along the polymer chains. All products exhibited a single relaxation that shifted towards longer times upon changing the catalysts’ molar ratios. Scanning electron microscopy results revealed that the fracture surface of the blends, synthesized by the binary catalyst system, became more heterogeneous in comparison with the products obtained by the individual use of the catalyst (I). The observed heterogeneity was found to increase by increasing the amount of catalyst (II). Such morphological change was further corroborated by the dynamic rheological data, indicating a promising correlation between the linear rheological results and the morphological features of the synthesized PP reactor blends.

1. Introduction

Polypropylene (PP) is one of the most commonly used plastics which is increasingly being utilized worldwide due to its rather low price, good processability and its ease of modification for different applications. Since being commercialized by Montedison Corporation in 1957 for the first time, a diverse range of catalysts and technologies have been developed for the fabrication of PP. However, the synthesis of PP with novel microstructure and tailored properties was further facilitated once the metallocene catalysts were developed [1,2,3,4,5,6,7]. Recent researches have been conducted with the aim of synthesizing polyolefins with improved microstructure and properties, and to this end, novel catalyst systems were designed. Of the new strategies to synthesize polyolefins with optimum properties, one could mention the alloy, hybrid and multi-component catalyst systems [8,9,10,11,12,13,14,15,16]. In those systems, each catalyst produces a polymer with a unique structure and properties. Due to the occurrence of chain transfer reactions from one active site to another, in the presence of a chain transfer agent such as trimethyl aluminum (TMA) or triisobutyl aluminum (TIBA), the final product is a reactor blend of two or more polymers possessing stereoblock copolymer microstructures, which exhibit different properties as compared to the polymers produced from the individual use of catalysts [17,18,19,20]. Several research groups successfully synthesized PP-based thermoplastic elastomers with excellent elastic properties, and also, stereoblock structures with the ability to compatibilize two heterogeneous polymer phases using a mixture of isospecific–aspecific and isospecific–syndiospecific metallocene catalysts [21,22]. Moreover, the synthesis of PP blends with novel properties possessing atactic, isotactic and stereoblock structures via the use of a mixture of methyl aluminoxane (MAO)-activated metallocene catalysts was reported [23]. Similar to other polymers, molecular weight (MW) and molecular weight distribution (MWD) are considered as crucial factors influencing the processing of PP. In spite of the good control over the MW of the synthesized products with tailored structure, which are regarded as the advantages of metallocene catalysts, the narrow MWD of the obtained polymers might limit the processability window and thus their potential applications. As is well-established, MW is responsible for the mechanical properties and MWD is highly influential on the processability and rheological properties of the final polymer. In many applications, such as blow molding, extrusion and packaging, polymers with bimodal MWD are needed to attain a product with high mechanical strength, stiffness and impact strength and also a good level of processability [24,25,26]. Since each of the catalysts within the binary catalyst systems is able to produce a unique polymer, it would be possible to achieve PPs with bimodal or broad MWDs if the catalyst system is properly designed. Therefore, some of the researchers used both homogeneous and heterogeneous binary metallocene silica-supported catalysts with different stereo-specificities to synthesize PPs with broad and bimodal MWD as well as stereoblock structures with different melting points [16,26,27,28,29,30,31,32,33,34]. Numerous studies have been conducted on the microstructural characterization of PPs synthesized by binary or hybrid catalyst systems as well as the effects of type and composition of catalysts on their microstructures through different characterization techniques [15,35,36,37]. However, there exists limited literature on the morphological and rheological properties of these systems and their relationship with the microstructure of the synthesized PPs. The aim of the current work is to study the microstructure, rheological and morphological characteristics of PP reactor blends with bimodal MWDs synthesized by a novel binary homogeneous system including (I): rac-Me2Si(2-Me-4-PhIn)2ZrCl2; and (II): (2-PhIn)2ZrCl2 catalysts (Scheme 1) at different molar ratios of the catalysts. In such binary systems, catalyst (I) is responsible for producing isotactic PP (i-PP) with high MW and catalyst (II) results in the production of an elastomeric PP with relatively low MW. An attempt is also made to establish correlations between morphology, microstructure and rheological properties of the synthesized PP reactor blends.

2. Experimental

2.1. Materials and Methods

The 2-Phenyl Indene, methyl aluminoxane (MAO, 10 wt % solution in toluene), n-BuLi, zirconium tetrachloride, and ethereal hydrochloric acid (1 N) were purchased from Aldrich and used as received. Triisobutyl aluminum (TIBA) and diethyl ether were obtained from Merck Chemical Co., Darmstadt, Germany. Polymerization grade propylene, n-hexane, n-heptane, and toluene were provided by Bandar Imam Petrochemical Co. (Tehran, Iran). The rac-Me2-Si(2-Me-4-Ph In)2ZrCl2 (I) was supplied by Molport, and (2-Ph In)2ZrCl2 (II), was synthesized according to a conventional technique described in the literature [38,39]. All solvents were refluxed over metallic sodium/benzophenone and distilled under nitrogen atmosphere prior to use. Propylene and nitrogen gas were dried by passing through columns containing a 3 Å molecular sieve. All reactions were performed under nitrogen atmosphere using the standard Schlenk technique and/or glovebox.

2.2. Catalyst Preparation

The catalyst precursors (I): rac-Me2-Si(2-Me-4-Ph In)2ZrCl2 and (II): (2-Ph In)2ZrCl2 were dissolved and homogenized in toluene. These solutions were used in propylene polymerization individually or in a mixed form with the predetermined Zr(II)/Zr(I) molar ratios.

2.3. Polymerization

Polymerization reactions were performed in a 600 mL double walled stainless steel autoclave equipped with controlling systems for temperature, stirring speed, and reaction pressure. A certain amount of dried toluene (350 mL) was introduced into the reactor under N2 purge. A fixed amount of TIBA or MAO was injected into the reactor as a scavenger in all runs. Then, the reactor was pressurized with propylene gas up to 6 bar, and the solution was saturated by stirring at 500 rpm. After that, a specific volume of pre-activated catalyst with MAO (10 min pre-activation) was injected into the reactor via a high-pressure catalyst injecting system and the polymerization was started. The total pressure was kept constant during the reaction and polymerization time was 1 h. The reaction was terminated by stopping the propylene feed and depressurizing the reactor. Then, the polymerization mixture was quenched within the acidified methanol (2% HCl), washed with fresh methanol, filtered, dried and weighed.

2.4. Characterization

2.4.1. Gel Permeation Chromatography (GPC)

MW and MWD of samples were measured by a high temperature size exclusion chromatography (SEC) technique on a PL-GPC 220 apparatus from Polymer Laboratories (Cambridge, UK) equipped with three columns. Samples with 1 mg/mL concentrations stabilized by 0.15 wt % butylated hydroxytoluene (BHT) were eluted with trichlorobenzene (TCB) at 145 °C and a flow rate of 1 mL/min.

2.4.2. Xylene Solubility

The xylene solubility of polymers was determined by a conventional method described elsewhere [5].

2.4.3. Rheological Properties

Dynamic rheometry in the melt state was carried out using a stress controlled rheometer (Anton Paar MCR301, Anton Paar GmbH, GRAZ, Austria) equipped with parallel plates geometry (diameter = 25 mm, gap = 1 mm). The samples were prepared as discs of 25 mm diameter and 2 mm thickness by compression molding. All measurements were done in a dry nitrogen atmosphere to suppress oxidative degradation. To achieve thermal equilibrium and structural relaxations, a waiting time after loading was applied before the measurements. Dynamic strain sweeps showed that rheological measurements performed at a strain of 5%, safely fall within the linear viscoelastic limit. Then, dynamic frequency sweeps were performed in the frequency range of 0.01–100 rad/s at a fixed temperature of 200 °C.

2.4.4. Scanning Electron Microscopy (SEM)

Morphology of the samples was analyzed by scanning electron microscopy (SEM) (VEGA, TESCAN, Brno, Czech Republic).

2.4.5. FTIR Analysis

Fourier transform infrared (FTIR) spectra were recorded on a Perkin–Elmer RXI spectrometer (Perkin–Elmer, Waltham, MA, USA) in the range of 1600–400 cm−1 with a resolution of 2 cm−1.

3. Results and Discussion

3.1. Polymerization

The polymerization results of catalysts (I) and (II) and their binary systems are tabulated in Table 1. It can be seen that the productivity of the binary catalyst increases with decreasing of Zr(II)/Zr(I) molar ratio. This could be considered as a result of a higher portion of catalyst (I) and its higher activity as compared to catalyst (II).

3.2. Molecular Weight and Molecular Weight Distribution

The MWD curves of polymers produced by the individual use of catalysts (I) and (II) and their binary systems are shown in Figure 1 and the quantitative values of average MWs and polydispersities are represented in Table 2. These curves show broad and also bimodal MWDs for the synthesized polymers by the binary catalysts. The appearance of two peaks in the MWD curves is indicative of the fact that the two catalysts are active during the polymerization in the case of the binary system. In addition, the average MWs are shifted to higher values in the polymer reactor blends. The increased MWs could be suggestive of decreased chain transfer reactions in two active catalytic sites and this feature is more remarkable for catalyst (I) (Table 2). Therefore, it can be concluded that catalysts were affected by each other since products with higher MW’s were obtained. When these two catalysts are mixed, the activity of catalyst (II) decreases (not reported here) and this decrease in activity can reduce the chain transfer and hence higher MWs products are obtained for the hybrid catalysts. For samples having a bimodal MWD, it is observed that the MWs at peaks (Table 2) are increased by increasing catalyst (II) content. The attained results indicate that the activity of binary catalysts, and as a consequence, MWs of the synthesized polymers, is highly sensitive to the molar ratios of catalysts. In these blends, the peak with high MW leads to products with considerable enhancement in mechanical properties, while the peak with low MW leads to an improvement in their processability. In other words, the increased tensile strength is accompanied by the improved processability.

3.3. FTIR Results

The FTIR spectra and corresponding data are reported in Figure 2 and Table 3, respectively. FTIR is one of the most common, simple and economical techniques for indirect measurement of the tacticity of PP. The 998 and 973 cm−1 absorption bands are characteristic bands assigned to helices chain conformation related to the isotactic segments that have different numbers of repeating units. The 998 and 973 cm−1 bands are assigned to segments with 11–12 and five repeating units, respectively. From the ratio of 998/973 absorption bands (A998/A973) known as the macrotacticity index and with the aid of the calibration curve, the PP tacticity can be evaluated [40,41,42,43].
The absorption band at 973 cm−1 is observed both in i-PP and a-PP with almost constant intensity. However, the intensity of the 998 cm−1 absorption band differs for these polymers. For this reason, the 973 cm−1 band is used as an internal reference while the A998/A973 ratio is used as the isotacticity index for PP. The intensity of the 998 cm−1 absorption band is proportional to the concentration of isotactic segments in PP chains. A decrease of an increase in the A998/A973 ratio is an indication of the reduction or enhancement of PP tacticity [41]. From the results presented in Table 3, it is obvious that the sample produced by catalyst (I) (PP-Cat I) is a PP with very high tacticity which shows FTIR bands typical of a commercial i-PP. Moreover, PP-Cat II is a PP with low tacticity content, exhibiting a band at 998 cm−1 with highly reduced intensity which is due to an inherent characteristic of catalyst (II) in producing polymers with large atactic blocks (segments).
FTIR spectra of PP-H Cat (25), PP-H Cat (32), and PP-H Cat (40) samples indicate that the A998/A973 ratio decreases with the increasing Zr(II)/Zr(I) ratio. In the other words, due to the reduction of 998 cm−1 band intensity, the isotacticity of the synthesized products is reduced. This reduced isotacticity from PP-H Cat (25) to PP-H Cat (40) can be attributed to the increased content of catalyst (II) in the binary catalyst system and to its higher activity as compared to the catalyst (I) which leads to the generation of polymeric chains with higher atactic segments.

3.4. Linear Rheological Behavior

3.4.1. Strain Sweep

Investigating the rheological behavior within the linear viscoelastic region is one of the most common methods for analyzing the structure of polymers. The variation of storage modulus in terms of strain amplitude for the synthesized PPs is shown in Figure 3 at a constant frequency of 10 rad/s within the strain range of 0.01%–100%. The attained results demonstrate that the linear viscoelastic region (LVR) occurs for the synthesized samples at strains lower than 20%. Therefore, in order to perform other dynamic sweeps and to avoid any non-linear responses, the strain amplitude was fixed at 5% to observe a more logical response at the low-frequency region.
The strain sweep test was reported for the PP-H Cat (40) sample since it has the highest MW among all samples. For this sample, it is shown that the strain of 5% safely falls within the linear viscoelastic region. The other samples which have lower MWs than the mentioned sample surely remain in the linear viscoelastic region at a strain of 5%.

3.4.2. Frequency Sweep

Figure 4 shows the storage modulus (G’) values, which are illustrated as a function of frequency within the linear viscoelastic region for the synthesized PPs using binary metallocene catalysts at different molar ratios of II/I (25, 32 and 40). According to this figure, the storage modulus values exhibit a rather similar variation trend for different samples within the whole frequency range. Moreover, all samples exhibit a modulus upturn at the low frequency region; similar to what is observed for the viscosity versus frequency curves presented subsequently [44,45,46]. Within the whole frequency range, the G’ values were found to be increased for all the synthesized PPs upon increasing the content of catalyst (II); albeit the majority of variations are observed within the low-frequency region. The observed plateau within the low-frequency region, which is associated with the solid-like behavior of the synthesized PPs induced by varying the composition of catalysts, is not observed for all the samples. As the molar ratio of II/I increases (from 25 to 40), the storage modulus within the low-frequency region exhibits a notable enhancement which could be attributed to the increased levels of MW and amorphous blocks in the synthesized PPs. These mentioned factors are themselves originated from the mixing of catalysts and their mutual effects on each other [47].
The complex viscosity (η*) is depicted in Figure 5 as a function of frequency for the synthesized PPs using catalyst (I) and the binary catalysts. Based on the results, all the synthesized PP reactor blends exhibit the plateau region at low frequencies, indicating their Newtonian behavior. As the molar ratio of II/I is increased, their complex viscosities show remarkable increments within the low frequencies, and the shear-thinning behavior becomes more discernible for all the synthesized samples. The observed enhancement in complex viscosity for the samples could be ascribed to the increased MW together with the higher level of chains’ entanglements [48,49,50]. Figure 6 exhibits the complex viscosity and storage modulus versus catalyst molar ratios which shows that the complex viscosity of the synthesized blends increases almost 47-fold by increasing the molar ratio of II/I. Such enhancement in the storage modulus is also observed. Based on these results, one could conclude that upon the variation of the molar ratio of II/I, the microstructure of the growing chains was changed as compared with the produced polymer from the individual use of catalyst (I). This change has occurred in such a way that the amorphous blocks were formed along the polymer chains due to the presence of catalyst (II) and its activeness in the course of polymerization [47,51,52]. On the other hand, the formation of amorphous blocks along the polymer chains also leads to increased chains’ entanglements which are majorly responsible for the increased complex viscosity of the synthesized PP reactor blends [46,53,54].
The relaxation time spectra can be attained from the first cross-over frequency of G’ and G” curves ( ω C 1 ). The cross-over point of G’ and G” curves is defined as the cross-over modulus (Gc) which distinguishes the viscose behavior from the elastic behavior [45,54]. Based on the cross-over point of G’ and G” curves in terms of frequency, one could evaluate the viscoelastic behavior of the understudied blends. According to Figure 7, the first cross-over point ( G C 1 ), at very low frequencies, is originated from the increased elasticity of the polymer melt due to the chains’ entanglements [41]. From the observed cross-over point shift to the lower frequencies, it could be inferred that the melt elasticity is increased as a result of the increased level of intermolecular entanglements. It also can be stated that with increasing the melt elasticity, the relaxation time shifts towards longer times [50,51].
According to Figure 8, as the molar ratio of catalysts increases from 25 to 40, Gc and ωc are changed from 24,500 and 106 to 6950 and 0.57, respectively. It can be concluded that with changing the molar ratio of II/I, the cross-over modulus and frequency are both decreased. The reason for the observed phenomenon could be ascribed to the higher elasticity of polymer melt due to the increased MW and also formation of amorphous blocks along the polymer chains [50].

3.4.3. Effect of Increasing Molar Ratio of Cat (II)/Cat (I) on the Relaxation Time

In Figure 9 and Figure 10, the relaxation spectra are illustrated in terms of λ within the linear viscoelastic region for the PP blends synthesized at different molar ratios of II/I. As the molar ratio of catalysts changes, all the samples exhibit an individual relaxation time peak which is shifted towards longer relaxation times with increasing the molar ratio of catalyst (II). Based on the obtained results, the PP-H Cat (40) sample exhibits the longest relaxation time (19.6 s) among the samples. The same trend is observed for the relaxation spectra of PP-H Cat (32) and PP-H Cat (25), and their relaxation times are 4.6 and 1.34 s, respectively.
According to Figure 9, it can be observed that the relaxation time and the heights of relaxation spectra H(λ)λ are increased for all the samples as the molar ratio of catalyst (II) is increased. The longer relaxation time can be attributed to the increased molecular weight of the samples. This indicates that increasing the molar ratio of catalyst (II) causes the elasticity to be increased due to the higher level of inter-chain entanglements leading to the longer relaxation time of chains after the shear flow is stopped. It can be concluded that increasing the molar ratio of II/I results in broadening the relaxation time spectrum and its consequent shift to the longer times. Therefore, the longer relaxation time, associated with the rigidity of the polymer chains, is due to the hindered motion of the chains as a result of chains’ entanglements, and accordingly, the sample with a molar ratio of 40 exhibits the longest relaxation time and the highest H(λ)λ peak height [45,46,50,54].

3.5. Correlation of Morphological and Rheological Properties

Figure 11 reveals the existing relationship between the morphological features and rheological behavior of samples synthesized at different molar ratios of II/I. The morphological features of the synthesized PPs via Cat (I) and the binary metallocene catalysts (25 and 40) are shown at the top of Figure 10. As can be seen, with increasing the molar ratio of catalyst (II) to catalyst (I), the morphology becomes more heterogeneous. Such morphological inhomogeneity is originated from the effect of increasing the content of catalyst (II) on the growing chains and also the effect of irregular atactic blocks formed during the course of polymerization as compared to the isotactic PP. In other words, the heterogeneity in the microstructure can be attributed to the formation of amorphous blocks along the polymer chains due to the activity of the catalyst (II) within the binary catalyst systems and also the increased MW of the samples which itself might be the major reason for the higher complex viscosity and storage modulus within the low-frequency region and also the higher ductility of polymer chains.
According to Figure 11, the observed changes in the morphological features, induced from increasing the II/I molar ratio, are further confirmed by the obtained dynamic rheological data. Therefore, it can be concluded that there exists a promising relationship between the linear rheological data and morphological features such that the chains’ elasticity is notably increased as the II/I molar ratio increases, especially at the low-frequency region [46,50,54].

4. Conclusions

The following conclusion can be drawn from the obtained results in the current study:
  • The MWD curves of synthesized products by the individual use of catalysts (I) and (II) and their binary systems show that MWD was broadened and became bimodal for products obtained from the catalysts’ mixtures. In addition, the average MWs were shifted to higher values in PP reactor blends. Actually, the appearance of two peaks in the MWD curves is indicative of the fact that two catalysts are active during the polymerization in the case of binary systems. In these blends, the peak at higher MW leads to a product with remarkable enhancement in mechanical properties, while the peak at lower MW leads to a product with improved processability. In other words, the improved tensile strength of the products is accompanied by their improved processability.
  • The complex viscosity of the synthesized blends shows a remarkable 47-fold enhancement as the molar ratio of II/I is increased. It can be concluded that upon the changes in the molar ratio of catalyst (II), the structure of the growing chains is changed such that the amorphous blocks along the polymer chains are formed due to the presence of catalyst (II) and its activeness in the course of polymerization. The formation of those amorphous blocks along the polymer chains increases the chains’ entanglements and thus enhances the complex viscosity of the synthesized PP reactor blends.
  • As the molar ratio of II/I changes, the cross-over modulus and frequency are reduced due to the increased elasticity of the polymer melt as a result of the existence of amorphous blocks along the polymer chains.
  • With increasing the molar ratio of II/I, all the peaks exhibited an individual relaxation peak which tends towards longer times as the molar ratio of catalyst (II) is increased. As a result, PP-H Cat (40) exhibits the longest relaxation time among the samples.
  • The changes in morphological features of obtained products induced by the increased molar ratio of II/I in the synthesized blends was precisely demonstrated via SEM images and also dynamic rheological data. Therefore, it can be concluded that there exists a robust relationship between the obtained results of linear rheology and morphological characteristics such that with increasing the molar ratio of the catalyst (II) within the binary system, the chains’ elasticity was significantly increased. It was also found that the amount of the mentioned enhancement within the low-frequency region is dependent on the formation of amorphous blocks along the PP chains.

Author Contributions

Javid Vaezi wrote the first draft of the paper based on his PhD research work. The research work has been conducted under supervision of Mehdi Nekoomanesh, Hossein Ali Khonakdar, and Seyed Hassan Jafari. Plots and figures are due to Alireza Mojarrad. He also helped with literature review and integrity of the paper.

Conflicts of Interest

The authors declare no conflict of interest.

References

  1. Vasile, C. (Ed.) Handbook of Polyolefins; CRC Press: Boca Raton, FL, USA, 2000.
  2. Moore, E.P. Polypropylene Handbook; Hanser: New York, NY, USA, 1996. [Google Scholar]
  3. Severn, J.R.; Chadwick, J.C. (Eds.) Tailor-Made Polymers: Via Immobilization of Alpha-Olefin Polymerization Catalysts; John Wiley & Sons: Hoboken, NJ, USA, 2008.
  4. Hoff, R.; Mathers, R.T. (Eds.) Handbook of Transition Metal Polymerization Catalysts; John Wiley & Sons: Hoboken, NJ, USA, 2010.
  5. Malpass, D.B.; Band, E.I. Introduction to Polymers of Propylene. Catal. Process. 2012. [Google Scholar] [CrossRef]
  6. Baugh, L.S.; Canich, J.A. (Eds.) Stereoselective Polymerization with Single-Site Catalysts; CRC Press: Boca Raton, FL, USA, 2007.
  7. Resconi, L.; Cavallo, L.; Fait, A.; Piemontesi, F. Selectivity in propene polymerization with metallocene catalysts. Chem. Rev. 2000, 100, 1253–1346. [Google Scholar] [CrossRef] [PubMed]
  8. Du, J.; Niu, H.; Dong, J.Y.; Dong, X.; Han, C.C. Self-Similar Growth of Polyolefin Alloy Particles in a Single Granule Multi-Catalyst Reactor. Adv. Mater. 2008, 20, 2914–2917. [Google Scholar] [CrossRef]
  9. Li, W.; Wang, J.; Jiang, B.; Yang, Y.; Jie, Z. Ethylene polymerization with hybrid nickel diimine/Cp2TiCl2 catalyst: A new method to prepare blends of linear and branched polyethylene. Polym. Int. 2010, 59, 617–623. [Google Scholar] [CrossRef]
  10. Wang, J.; Niu, H.; Dong, J.; Du, J.; Han, C.C. Morphology and mechanical properties of polypropylene/poly (propylene-1-octene) in-reactor alloys prepared by Metallocene/Ziegler–Natta hybrid catalyst. Polymer 2012, 53, 1507–1516. [Google Scholar] [CrossRef]
  11. Hong, S.C.; Mihan, S.; Lilge, D.; Delux, L.; Rief, U. Immobilized Me2Si(C5Me4)(N-tBu)TiCl2/(nBuCp)2ZrCl2 hybrid metallocene catalyst system for the production of poly (ethylene-co-hexene) with pseudo-bimodal molecular weight and inverse comonomer distribution. Polym. Eng. Sci. 2007, 47, 131–139. [Google Scholar] [CrossRef]
  12. Kaminsky, W. Discovery of methylaluminoxane as cocatalyst for olefin polymerization. Macromolecules 2012, 45, 3289–3297. [Google Scholar] [CrossRef]
  13. Nejabat, G.R.; Nekoomanesh, M.; Arabi, H.; Salehi-Mobarakeh, H.; Zohuri, G.H.; Omidvar, M.; Miller, S.A. Synthesis and microstructural study of stereoblock elastomeric polypropylenes from metallocene catalyst (2-PhInd)2ZrCl2 activated with cocatalyst mixtures. J. Polym. Sci. A 2013, 51, 724–731. [Google Scholar] [CrossRef]
  14. Nejabat, G.R.; Nekoomanesh, M.; Arabi, H.; Salehi-Mobarakeh, H.; Zohuri, G.H.; Omidvar, M.; Miller, S.A. Synthesis of Stereoblock Elastomeric Poly(propylene) s Using a (2-PhInd)2ZrCl2 Metallocene Catalyst in the Presence of Co-Catalyst Mixtures: Study of Activity and Molecular Weight. Macromol. React. Eng. 2012, 6, 523–529. [Google Scholar] [CrossRef]
  15. Nejabat, G.R.; Nekoomanesh, M.; Arabi, H.; Salehi-Mobarakeh, H.; Zohuri, G.H.; Mortazavi, M.M.; Ahmadjo, S.; Miller, S.A. Study of Ziegler-Natta/(2-PhInd)2ZrCl2 hybrid catalysts performance in slurry propylene polymerization. Polyolefins J. 2015, 2, 73–87. [Google Scholar]
  16. Paredes, B.; van Grieken, R.; Carrero, A.; Lopez-Moya, E. Bimodal polypropylene through binary metallocene catalytic systems: Comparison between hybrid and mixed heterogeneous catalysts. J. Polym. Res. 2016, 23, 1–5. [Google Scholar] [CrossRef]
  17. Galli, P.; Collina, G.; Sgarzi, P.; Baruzzi, G.; Marchetti, E. Combining Ziegler-Natta and mettalocene catalysis: New heterophasic propylene copolymers from the novel multicatalyst reactor granule technology. J. Appl. Polym. Sci. 1997, 66, 1831–1837. [Google Scholar] [CrossRef]
  18. Cho, H.S.; Choi, D.J.; Lee, W.Y. Polymerization of ethylene and ethylene/1-hexene over Ziegler-Natta/Metallocene hybrid catalysts supported on SiO2 prepared by a sol-gel method. J. Appl. Polym. Sci. 2000, 78, 2318–2326. [Google Scholar] [CrossRef]
  19. Pan, L.; Zhang, K.Y.; Li, Y.G.; Bo, S.Q.; Li, Y.S. Thermal and crystallization behaviors of polyethylene blends synthesized by binary late transition metal catalysts combinations. J. Appl. Polym. Sci. 2007, 104, 4188–4198. [Google Scholar] [CrossRef]
  20. Fu, Z.; Xu, J.; Zhang, Y.; Fan, Z. Chain structure and mechanical properties of polyethylene/polypropylene/poly(ethylene-co-propylene)in-reactor alloys synthesized with a spherical Ziegler–Natta catalyst by gas-phase polymerization. J. Appl. Polym. Sci. 2005, 97, 640–647. [Google Scholar] [CrossRef]
  21. Chien, J.C.; Iwamoto, Y.; Rausch, M.D.; Wedler, W.; Winter, H.H. Homogeneous Binary Zirconocenium Catalyst Systems for Propylene Polymerization. 1. Isotactic/Atactic Interfacial Compatibilized Polymers Having Thermoplastic Elastomeric Properties. Macromolecules 1997, 30, 3447–3458. [Google Scholar] [CrossRef]
  22. Chien, J.C.; Iwamoto, Y.; Rausch, M.D. Homogeneous binary zirconocenium catalysts for propylene polymerization. II. Mixtures of isospecific and syndiospecific zirconocene systems. J. Polym. Sci. A 1999, 37, 2439–2445. [Google Scholar] [CrossRef]
  23. Lieber, S.; Brintzinger, H.H. Propene polymerization with catalyst mixtures containing different ansa-zirconocenes: Chain transfer to alkylaluminum cocatalysts and formation of stereoblock polymers. Macromolecules 2000, 33, 9192–9199. [Google Scholar] [CrossRef]
  24. Mark, H.F. Encyclopedia of Polymer Science and Technology; John Wiley & Sons: Hoboken, NJ, USA, 2005. [Google Scholar]
  25. Premphel, K.; Paecharoechal, W. Polypropylene/metallocene ethylene-octene copolymer blends with a bimodal particle size distribution: Mechanical properties and their controlling factors. J. Appl. Polym. Sci. 2002, 85, 2412–2418. [Google Scholar] [CrossRef]
  26. Moya, E.L.; Van Grieken, R.; Carrero, A.; Paredes, B. Bimodal Poly(propylene) through Binary Metallocene Catalytic Systems as an Alternative to Melt Blending. Macromol. Symp. 2012. [Google Scholar] [CrossRef]
  27. Marques, M.D.F.V.; Chavez, E.G. Polypropylene fractions produced by binary metallocene catalysts. J. Polym. Sci. A 2003, 41, 1478. [Google Scholar] [CrossRef]
  28. De Fátima, V.M.M.; Pombo, C.C.; Silva, R.A.; Conte, A. Binary metallocene supported catalyst for propylene polymerization. Eur. Polym. J. 2003, 39, 561–567. [Google Scholar]
  29. Bastos, Q.C.; Marques, D.F.V. Polypropylene reactor mixture obtained with homogeneous and supported catalysts. J. Polym. Sci. A 2005, 43, 263–272. [Google Scholar] [CrossRef]
  30. Tynys, A.; Eilertsen, J.L.; Seppala, J.V.; Rytter, E. Propylene polymerizations with a binary metallocene system—Chain shuttling caused by trimethylaluminium between active catalyst centers. J. Polym. Sci. A 2007, 45, 1364–1376. [Google Scholar] [CrossRef]
  31. Tynys, A.; Saarinen, T.; Bartke, M.; Löfgren, B. Propylene polymerisations with novel heterogeneous combination metallocene catalyst systems. Polymer 2007, 48, 1893–1902. [Google Scholar] [CrossRef]
  32. Reddy, B.R.; Shamshoum, E.S.; Fina Technology, Inc. Process for a Isotactic/Syndiotactic Polymer Blend in a Single Reactor. U.S. Patent US5,804,524, 8 September 1998. [Google Scholar]
  33. Ahn, T.O.; Hong, S.C.; Kim, J.H.; Lee, D.H. Control of molecular weight distribution in propylene polymerization with Ziegler–Natta/metallocene catalyst mixtures. J. Appl. Polym. Sci. 1998, 67, 2213–2222. [Google Scholar] [CrossRef]
  34. Shamshoum, E.S.; Bauch, C.G. Catalyst Yield from Supported Metallocene Catalysts. U.S. Patent 5,847,059, 8 December 1998. [Google Scholar]
  35. Auriemma, F.; De Rosa, C.; Corradi, M. Stereoblock Polypropylene as a Prototype Example of Elasticity via a Flip-Flop Reorientation of Crystals in a Compliant Matrix. Adv. Mater. 2007, 19, 871–874. [Google Scholar] [CrossRef]
  36. Macko, T.; Cutillo, F.; Busico, V.; Brüll, R. Separation of poly(propylene) samples according to tacticity using a hypercarb column. Macromol. Symp. 2010. [Google Scholar] [CrossRef]
  37. Descour, C.; Macko, T.; Cavallo, D.; Parkinson, M.; Hubner, G.; Spoelstra, A.; Villani, M.; Duchateau, R. Synthesis and characterization of iPP-sPP stereoblock produced by a binary metallocene system. J. Polym. Sci. A 2014, 52, 1422–1434. [Google Scholar] [CrossRef]
  38. Arabi, H.; Mobarakeh, H.S.; Balzadeh, Z.; Nejabat, G.R. Copolymerization of ethylene/5-ethylidene-2-norbornene with bis (2-phenylindenyl) zirconium dichloride catalyst: I. Optimization of the operating conditions by response surface methodology. J. Appl. Polym. Sci. 2013, 129, 3047–3053. [Google Scholar] [CrossRef]
  39. Balboni, D.; Camurati, I.; Ingurgio, A.C.; Guidotti, S.; Focante, F.; Resconi, L. A counterintuitive, yet efficient synthesis of bis (indenyl) zirconium dihalides. J. Organomet. Chem. 2003, 683, 2–10. [Google Scholar] [CrossRef]
  40. Ozzetti, R.A.; de Oliveira Filho, A.P.; Schuchardt, U.; Mandelli, D. Determination of tacticity in polypropylene by FTIR with multivariate calibration. J. Appl. Polym. Sci. 2002, 85, 734–745. [Google Scholar] [CrossRef]
  41. Burfield, D.R.; Loi, P.S. The use of infrared spectroscopy for determination of polypropylene stereoregularity. J. Appl. Polym. Sci. 1988, 36, 279–293. [Google Scholar] [CrossRef]
  42. Sundell, T.; Fagerholm, H.; Crozier, H. Isotacticity determination of polypropylene using FT-Raman spectroscopy. Polymer 1996, 37, 3227–3231. [Google Scholar] [CrossRef]
  43. Luongo, J.P. Infrared Study of Polypropylene. J. Appl. Polym. Sci. 1960, 3, 302–309. [Google Scholar] [CrossRef]
  44. Mojarrad, A.; Jahani, Y.; Barikani, M. Investigation on the correlation between rheology and morphology of PA6/ABS blends using ethylene acrylate terpolymer as compatibilizer. J. Appl. Polym. Sci. 2011, 120, 2173–2182. [Google Scholar] [CrossRef]
  45. Mojarrad, A.; Jahani, Y.; Barikani, M. Influence of nanoclay on the rheological properties of polyamide 6/acrylonitrile butadiene styrene nanocomposites. J. Appl. Polym. Sci. 2012, 125, E571–E582. [Google Scholar] [CrossRef]
  46. Seock, C.H.; Suck, C.Y.; Young, L. Control of molecular weight distribution for polyethylene catalyzed over Ziegler–Natta/Metallocene hybrid and mixed catalysts. J. Mol. Catal. A 2000, 159, 203–213. [Google Scholar]
  47. Chen, Y.; Zou, H.; Liang, M.; Liu, P. Study on the dynamic rheological behavior of four different bimodal polyethylenes. J. Macromol. Sci. B 2013, 52, 924–936. [Google Scholar] [CrossRef]
  48. Starck, P.; Malmberg, A.; Löfgren, B. Thermal and rheological studies on the molecular composition and structure of metallocene-and Ziegler–Natta-catalyzed ethylene–α-olefin copolymers. J. Appl. Polym. Sci. 2002, 83, 1140–1156. [Google Scholar] [CrossRef]
  49. Muñoz-Escalona, A.; Lafuente, P.; Vega, J.F.; Santamaría, A. Rheology of metallocene-catalyzed monomodal and bimodal polyethylenes. Polym. Eng. Sci. 1999, 39, 2292–2303. [Google Scholar] [CrossRef]
  50. Wood-Adams, P.M.; Dealy, J.M.; Degroot, A.W.; Redwine, O.D. Effect of molecular structure on the linear viscoelastic behavior of polyethylene. Macromolecules 2000, 33, 7489–7499. [Google Scholar] [CrossRef]
  51. Coates, G.W.; Waymouth, R.M. Oscillating stereocontrol: A strategy for the synthesis of thermoplastic elastomeric polypropylene. Science 1995, 267, 217. [Google Scholar] [CrossRef] [PubMed]
  52. Hu, Y.; Carlson, E.D.; Fuller, G.G.; Waymouth, R.M. Elastomeric polypropylenes from unbridged 2-phenylindene zirconocene catalysts: Temperature dependence of crystallinity and relaxation properties. Macromolecules 1999, 32, 3334–3340. [Google Scholar] [CrossRef]
  53. Kurzbeck, S.; Oster, F.; Münstedt, H.; Nguyen, T.Q.; Gensler, R. Rheological properties of two polypropylenes with different molecular structure. J. Rheol. 1999, 43, 359–374. [Google Scholar] [CrossRef]
  54. Hussein, I.A.; Hameed, T.; Williams, M.C. Influence of molecular structure on the rheology and thermorheology of metallocene polyethylenes. J. Appl. Polym. Sci. 2006, 102, 1717–1728. [Google Scholar] [CrossRef]
Scheme 1. Precursor (I): rac-Me2Si(2-Me-4-Ph In)2ZrCl2 and (II): activated oscillating (2-Ph In)2ZrCl2 catalyst.
Scheme 1. Precursor (I): rac-Me2Si(2-Me-4-Ph In)2ZrCl2 and (II): activated oscillating (2-Ph In)2ZrCl2 catalyst.
Polymers 09 00075 sch001
Figure 1. MWD Curves of the synthesized PP reactor blends by use of individual and binary catalysts: (a) PP-Cat I; (b) PP-Cat II; (c) PP-H Cat (25); (d) PP-H Cat (32); (e) PP-H Cat (40).
Figure 1. MWD Curves of the synthesized PP reactor blends by use of individual and binary catalysts: (a) PP-Cat I; (b) PP-Cat II; (c) PP-H Cat (25); (d) PP-H Cat (32); (e) PP-H Cat (40).
Polymers 09 00075 g001
Figure 2. FTIR spectra of PP reactor blends synthesized with the binary and individual catalyst systems.
Figure 2. FTIR spectra of PP reactor blends synthesized with the binary and individual catalyst systems.
Polymers 09 00075 g002
Figure 3. Storage modulus versus strain amplitude at a constant frequency of 10 rad/s and temperature of 200 °C.
Figure 3. Storage modulus versus strain amplitude at a constant frequency of 10 rad/s and temperature of 200 °C.
Polymers 09 00075 g003
Figure 4. Storage modulus versus frequency for the PP reactor blends synthesized using binary metallocene catalysts at different molar ratios.
Figure 4. Storage modulus versus frequency for the PP reactor blends synthesized using binary metallocene catalysts at different molar ratios.
Polymers 09 00075 g004
Figure 5. Complex viscosity versus frequency for the synthesized PP reactor blends.
Figure 5. Complex viscosity versus frequency for the synthesized PP reactor blends.
Polymers 09 00075 g005
Figure 6. Storage modulus and complex viscosity as a function of molar ratio of the catalysts at a frequency of 0.01 rad/s.
Figure 6. Storage modulus and complex viscosity as a function of molar ratio of the catalysts at a frequency of 0.01 rad/s.
Polymers 09 00075 g006
Figure 7. G’, G” and η* values in terms of frequency for the synthesized PP reactor blends with different molar ratios of cat (II)/cat (I).
Figure 7. G’, G” and η* values in terms of frequency for the synthesized PP reactor blends with different molar ratios of cat (II)/cat (I).
Polymers 09 00075 g007
Figure 8. Gc and ωC values for the synthesized PP reactor blends at different molar ratios of cat (II)/cat (I).
Figure 8. Gc and ωC values for the synthesized PP reactor blends at different molar ratios of cat (II)/cat (I).
Polymers 09 00075 g008
Figure 9. H(λ)λ and H(λ) for the PP reactor blends synthesized at different molar ratios of cat (II)/cat (I).
Figure 9. H(λ)λ and H(λ) for the PP reactor blends synthesized at different molar ratios of cat (II)/cat (I).
Polymers 09 00075 g009
Figure 10. Relaxation time values for the PP reactor blends synthesized at different molar ratios of cat (II)/cat (I).
Figure 10. Relaxation time values for the PP reactor blends synthesized at different molar ratios of cat (II)/cat (I).
Polymers 09 00075 g010
Figure 11. Relationship between the morphology and linear rheology of PP reactor blends synthesized at different cat (II)/cat (I) molar ratios.
Figure 11. Relationship between the morphology and linear rheology of PP reactor blends synthesized at different cat (II)/cat (I) molar ratios.
Polymers 09 00075 g011
Table 1. Polymerization results of catalysts (I) and (II) and their binary systems.
Table 1. Polymerization results of catalysts (I) and (II) and their binary systems.
RunSample rodeZr(II)/Zr(I) (Molar ratio)Zr(t) × 104 (mmol)Al/Zr(t)Polymer wt (g)Productivity (kg PP/mmol Zr(t)·h)
1PP-Cat I(I) only3.5110010.028.8
2PP-Cat II(II) only7511006.00.80
3PP-H Cat (25)2545.6110054.311.9
4PP-H Cat (32)3257.8110066.511.5
5PP-H Cat (40)4071.8110030.94.3
Polymerization condition: Toluene = 350 mL, P = 6 bar, T = 40 °C, t = 60 min, methyl aluminoxane (as Scavenger) = 1 mL, rpm = 500, pre-activation time: 10 min.
Table 2. MW and MWD of the synthesized PP reactor blends.
Table 2. MW and MWD of the synthesized PP reactor blends.
RunSample codeZr(II)/Zr(I)MW (g/mol)PDI aPeak maxXylene solubility (wt %)
Low MW (g/mol)High MW (g/mol)
1PP-Cat I(I) only469,0002.8383,000 b2.6
2PP-Cat II(II) only115,0004.543,000 b84
3PP-H Cat (25)251,340,000b.m c66,000704,00023
4PP-H Cat (32)322,850,000b.m201,0002,410,00028
5PP-H Cat (40)404,420,000b.m366,0004,120,00035
a Polydispersity Index, b Unimodal, c Bimodal.
Table 3. FTIR results of PP reactor blends synthesized with the binary and individual catalyst systems.
Table 3. FTIR results of PP reactor blends synthesized with the binary and individual catalyst systems.
Sample codeZr(II)/Zr(I)A998 (Peak height)A973 (Peak height)A998/A973Isotacticity 1Isotacticity 2
PP-Cat I(I) only64.775.20.8696.897.4
PP-Cat II(II) only7.877.90.102016
PP-H Cat (25)2549.174.40.6676.277
PP-H Cat (32)3243.576.30.5770.172
PP-H Cat (40)4040.477.60.5263.365
1 Calculated from the calibration curve reported in [41]; 2 From xylene solubility.

Share and Cite

MDPI and ACS Style

Vaezi, J.; Nekoomanesh, M.; Khonakdar, H.A.; Jafari, S.H.; Mojarrad, A. Correlation of Microstructure, Rheological and Morphological Characteristics of Synthesized Polypropylene (PP) Reactor Blends Using Homogeneous Binary Metallocene Catalyst. Polymers 2017, 9, 75. https://doi.org/10.3390/polym9030075

AMA Style

Vaezi J, Nekoomanesh M, Khonakdar HA, Jafari SH, Mojarrad A. Correlation of Microstructure, Rheological and Morphological Characteristics of Synthesized Polypropylene (PP) Reactor Blends Using Homogeneous Binary Metallocene Catalyst. Polymers. 2017; 9(3):75. https://doi.org/10.3390/polym9030075

Chicago/Turabian Style

Vaezi, Javid, Mehdi Nekoomanesh, Hossein Ali Khonakdar, Seyed Hassan Jafari, and Alireza Mojarrad. 2017. "Correlation of Microstructure, Rheological and Morphological Characteristics of Synthesized Polypropylene (PP) Reactor Blends Using Homogeneous Binary Metallocene Catalyst" Polymers 9, no. 3: 75. https://doi.org/10.3390/polym9030075

Note that from the first issue of 2016, this journal uses article numbers instead of page numbers. See further details here.

Article Metrics

Back to TopTop