Next Article in Journal
A Cross-Layer Biometric Recognition System for Mobile IoT Devices
Previous Article in Journal
A Compact In-Line Waveguide-to-Microstrip Transition in the Q-Band for Radio Astronomy Applications
 
 
Font Type:
Arial Georgia Verdana
Font Size:
Aa Aa Aa
Line Spacing:
Column Width:
Background:
Article

Design of a Low-Cost Microstrip Directional Coupler with High Coupling for a Motion Detection Sensor

1
R&D Labs, CIAS Elettronica, 20158 Milano, Italy
2
Dipartimento di Ingegneria Elettrica ed Elettronica, Università degli Studi di Cagliari, 09123 Cagliari, Italy
3
EMC Research and Measurement Center of Navy, Shanghai 200235, China
*
Author to whom correspondence should be addressed.
Electronics 2018, 7(2), 25; https://doi.org/10.3390/electronics7020025
Submission received: 2 January 2018 / Revised: 21 February 2018 / Accepted: 22 February 2018 / Published: 24 February 2018

Abstract

:
A coupled-line coupler based on the asymmetric cascade connection of two coupled line sections is used to achieve a high coupling factor using low-cost material and technology in the X frequency band, and its performance is compared with a standard quarter-wave, coupled-line coupler, showing an increase in the coupling factor of about 3 dB. The proposed coupler can be effectively used in a Doppler motion detection sensor, due to its strong coupling and relatively high isolation. The coupler is designed through a simple, yet rigorous, equivalent circuital model. Then, an optimization procedure was performed using the commercial software Ansys HFSS in order to compensate for losses and second order effects. A prototype of the designed coupler was realized, and the measured data show very good agreement with simulations.

1. Introduction

The aim of motion detection systems (MDS) is the detection of the movement of scattering objects. MDS are normally used for security purpose, such as to protect indoor areas, and locations where important assets are located (museums, libraries), or in automotives to avoid car collisions. The detection of a movement usually triggers an alarm, or, more generally, activates other electronic subsystems.
MDS use different methods to detect movement, and can be divided into two main categories: passive detectors and active detectors. Passive detectors (for example, most infrared detectors) do not send out signals but merely receive signals, such as changes in brightness temperature, light intensity and so on. On the other hand, active detectors (such as microwave detectors) act as a radar, i.e., they transmit energy that propagates in the protected area, it is scattered by the existing bodies, and then it is received back by the MDS. In this case, for example, an alarm can be triggered by any perturbation of the reflected waves caused by a moving object or by any movement of a body with a Radar Cross Section (RCS) larger than a prescribed threshold (e.g., to detect humans but prevent the detection of mice). A block diagram of a microwave MDS is shown in Figure 1. The microwave part of the MDS is made by a voltage-controlled oscillator, a low pass filter, a transmitting and a receiving antenna, a mixer and a directional coupler. The directional coupler is required to perform coherent detection of the received signal, thus allowing a larger receiver sensitivity and then a larger detection range. Thus, this coupler requires both strong coupling and large isolation. On the other hand, it should be compact and low-cost. As such, the directional coupler is one of the most critical components of a microwave MDS.
In this paper we focus on the design of the directional coupler employed to feed the mixer for the “MURENA” Doppler motion detection sensor (DMDS) [1]. MURENA is a volumetric X band microwave sensor, using the Doppler effect and digital signal processing, for external protection. Like all sensors using microwave technology to detect motion, MURENA exploits the principle of a Doppler radar, where a continuous wave of microwave radiation is emitted by a RF source. The frequency shift in the reflected waves, due to the motion of an object toward (or away from) the receiver, results in a signal at low frequency. The MURENA interface between the microwave transmitter–receiver is designed using a special circuit, which generates a modulation signal on the transmitter, demodulating and pre-amplifying the received signal using two separate channels. This performance is then enhanced by subsequent signal processing which, after amplification, is digitized using an analogue/digital convertor. This digital signal is handled in real time by the on-board microprocessor. Using appropriate algorithms it is possible to measure the distance and the mass of the object moving within the detection area, analyzing all the received data using a “fuzzy” logic. Figure 1 reports a block diagram of the whole sensor. The mixer used in this system is a single balanced 180° “rat-race” type, which, in order to work properly, requires a DC-isolated directional coupler with a large coupling, typically larger than −7 dB. The operating frequency range, 10–11 GHz, was chosen to comply with different national regulations.
The most popular configuration of a directional coupler is the standard coupled-line directional coupler (SC) [2,3,4], which allows the realization of quite a compact coupler with good bandwidth. Moreover, the coupled port is DC isolated from the through line. On the other hand, the strongest coupling factor of a standard coupler realization is limited to about 9–10 dB [2]. Such values are too small for our application (and for many similar applications). Increasing the coupling requires very close coupling lines, which can be realized only using high-cost processing over expensive PCB [5]. As an alternative, stronger coupling factors can be obtained with more complex (and bigger) structures, such as the Lange coupler [2], or other special techniques [6,7], not compatible with the system target price. Therefore, a compact coupler configuration, able to realize a relatively strong coupling factor, with low-cost material and technology (and therefore using large inter-line spacing), such as those needed by a MDS, requires a different configuration.
Simple and compact coupler configurations, based on the asymmetric cascade connection of two coupled line sections, are proposed in [8] in the lower UHF frequency band (600 MHz) in order to improve flexibility in the design of couplers for complex circuit environments, within a limited area. In this paper, we use essentially the same configuration presented in [8], but for a different purpose, i.e., in order to achieve tight coupling and high directivity, compared to the SC [2], in the X frequency band, using low-cost materials and technology. However, the improvement is not straightforward, since increasing the coupling factor using low-cost material in a far higher frequency range, where dielectric and ohmic losses could be critical, can be challenging. We will demonstrate that the selected configuration is able to strengthen the coupling factor over that of a SC with the same inter-line spacing. This improvement is obtained at the expense of the total coupler size. However, as shown in Section 3, this size increase does not significantly affect the coupler loss efficiency. In fact, in our case, the actual coupling region increases only by 10% compared to the SC (from 90° to 100°).
The design of the directional coupler was performed through a simplified circuital model, and then optimized by using the commercial software HFSS by Ansys. A prototype has been realized by R&D Labs of CIAS Elettronica, using a low-cost laminate. Measured results on the realized prototype are in very good agreement with simulations, allowing the achievement of the coupling factor required by the design specifications. The proposed directional coupler was also compared with a SC with the same inter-line spacing, showing its ability to increase the coupling factor.

2. Analysis of the Proposed Configuration

The scheme of the proposed coupler is shown in Figure 2a. Networks A and D are two equal coupled line sections (CLSs) acting as directional couplers with port impedances Z0 = 50 Ω, whereas B and C are microstrip transmission lines with characteristic impedances Z0. Let ϑB and ϑC denote the electrical lengths of the transmission lines B and C; ϑB should be equal to the required spacing between the two CLSs, whereas ϑC is usually chosen to be longer than ϑB, as line C can be realized as a meander line. The microstrip realization of the proposed coupler is reported in Figure 2b.
Since we are interested in achieving the strongest coupling factor available, the inter-line spacing S is the smallest spacing compatible with the chosen technology. Then, the matching condition (ZeZo)/(Zo2) = 1 [2] must be enforced, wherein Ze, Zo are the even and odd mode impedances of the coupled line section. As a consequence, the width W (see Figure 2b) is also completely determined [2].
We further assume, for the moment, that the CLSs are ideal, i.e., that the propagation constants of both the even and the odd mode are equal, and we denote this constant by βC. In this case, we have all ports matched and an infinite isolation over the whole frequency range [2].
Letting ϑA = βCLA be the electrical length of the first CLS, its scattering matrix can be obtained by [2]
S 21 = T 0 ( ϑ A ) = 1 k 2 1 k 2 cos ( ϑ A ) + j sin ( ϑ A )
S 31 = K 0 ( ϑ A ) = j k sin ( ϑ A ) 1 k 2 cos ( ϑ A ) + j sin ( ϑ A )
where k = (ZeZo)/(Ze + Zo) is the maximum of the coupling coefficient S31 achieved for ϑA = π/2. Then, the total coupling factor of the coupler in Figure 2 is derived in ([8], Equation (4)), and can be written as
C = | K 0 1 + [ T o 2 K o 2 ] exp [ j ( ϑ B + ϑ C ) ] 1 K o 2 exp [ j ( ϑ B + ϑ C ) ] |
Now, k is determined by the CLS geometry, so C is only a function of ϑA and of ϑB + ϑC. Therefore, the individual lengths ϑB and ϑC can be chosen to cope with the size requirements. In Figure 3 we show the behavior of C as a function of ϑB + ϑC (for different ϑA values) for k = −9.6 dB. From the results in Figure 3, it follows that the optimal value of ϑB + ϑC is around 280° for short CLSs, and becomes smaller as the length of the CLS increases. Moreover, the longer the ϑA, the stronger the optimal coupling factor.

3. Coupler Design and Testing

The proposed coupler can be used in many different microwave systems. However, in order to experimentally assess the proposal, we decided to realize and test a coupler to be used in X-band DMDS. The requirements are therefore a strong coupling (C ≥ −7 dB) between the through line and the coupling port over the bandwidth 10–11 GHz, using a low-cost PCB and process. Therefore, we selected an organic–ceramic laminate, with εr = 3.5 and tan(δ) = 0.003. The dielectric slab thickness was 0.762 mm and the copper thickness was 35 μm. The smallest spacing available on this PCB with a standard (cheap) process was 0.15 mm, and this value was used for the gap S between the coupled lines.
Using [9], the matching condition (ZeZo)/(Zo2) = 1 results in W = 1.4 mm. Then, the even and odd impedances (computed using HFSS) are Ze = 69.8 Ω, Zo = 35.2 Ω, leading to k = −9.6 dB.
The main available degree of freedom is the length ϑA of the CLSs. It is apparent from Figure 3 that the longer the ϑA, the larger both C and the increase in coupling, C/k. However, increasing ϑA produces larger losses in the CLSs and a trade-off is required between C/k on the one hand, and total coupler size and losses on the other. We selected ϑA = 50° as a value, giving C/k = 3.3 dB, aiming at C ≥ −7 dB over the operating bandwidth. From ϑA = 50° and choosing ϑB = 90°, we get, from Figure 3, the starting value of ϑC = 160°.
An optimization is then needed for ϑC (i.e., on LC2 in Figure 2, since LC1 is fixed by LB) to compensate for losses and second-order effects. As a matter of fact, the bend angles of the meander line (αC2) and the bends towards the coupler ports (αF1) also need to be optimized (see Figure 2). Moreover, in order to avoid the tapering of the microstrip lines B and C in connection with the CLSs (W = 1.4 mm, whereas a 50 Ω microstrip line has width W0 = 1.7 mm), in the optimized configuration these lines were selected with the same width W = 1.4 mm as the CLSs. Since this value corresponds to a characteristic impedance of about 56 Ω, we can assume that this approximation does not affect the required coupler behavior.
To perform the optimization, the coupler of Figure 2a was simulated using HFSS. The optimization parameters are: LC2, the angles αC2 (determining the electrical length ϑC), and the angles αF1 of the bends in the feeding lines. The geometrical parameters of the optimized geometry, obtained after a short trial and error procedure on LC2, αC2, and αF1, are summarized in Table 1 (optimized parameters are in bold). The last bend in the feeding lines, before each feeding port, must leave room for the soldering of SMA PCB connectors, whereas the length LF2 (= 3 mm) was to be as short as possible, provided that it did not affect the coupler behavior.
A prototype of the designed coupler was realized by the R&D Labs of CIAS Elettronica (see Figure 4, right). For comparison, a SC with the same inter-line spacing S was also realized (Figure 4, left). In Figure 5 the simulated (HFSS) and measured frequency response of the couplers in Figure 4 are reported. The agreement between the simulated and experimental data is very good for both prototypes.
From the results in Figure 5b it appears that the response of the directional coupler in Figure 4 (right) is coherent with the simplified analysis based on Equation (3) and fully complies with the design specifications, since C ≥ −7 dB in the operating bandwidth. Moreover, the resulting coupling factor at the center frequency (6.1 dB—measured data) is about 2.9 dB stronger than the standard quarter-wave coupler on the same PCB and with the same inter-line spacing (see Figure 5). From Figure 5, it also follows that the directivity (measured data) of the proposed coupler (28–30 dB in the operating bandwidth) is about 7 dB larger than the directivity of the SC. Therefore, the initial hypothesis on the equality of the phase velocities can be accepted, and no compensation for the difference in those speeds is needed [10].
Finally, we wanted to evaluate the loss efficiency of the modified coupler in Figure 2 compared to a SC. In order to do this, we observe that, for a lossless network, the dot product of any column of its scattering matrix with the conjugate of that column is equal to one [2]. Therefore, the loss efficiency can be computed evaluating how much the parameter η, defined as η = | S 11 | 2 + | S 21 | 2 + | S 31 | 2 + | S 41 | 2 , deviates from unity. In Figure 6, we plot the parameter η for both the modified and the standard coupler. The average η over the bandwidth 10–11 GHz for the SC is about 88%, whereas the average η of the modified coupler is about 84%. This difference is mainly due to the overall longer CLS (100° compared to 90°), since the losses are concentrated at and around the gaps of the CLSs, where the surface current density is stronger.

4. Conclusions

We presented a coupled-line microstrip coupler for high coupling over a relatively large bandwidth (10%). This coupler was designed and realized using a low cost PCB in the X frequency band, with standard technology, and allows us to achieve stronger coupling over a standard coupled-line directional coupler with the same inter-line spacing. It presents a simple and compact structure compared to other configurations used to increase the coupling factor, and with its strong coupling and relatively high isolation, can be effectively used in a Doppler motion detection sensor.

Author Contributions

All the authors contributed to the design of the directional couplers, Giovanni Sanna and Giorgio Montisci performed the experimental characterization of the realized prototypes; Giorgio Montisci wrote the paper.

Conflicts of Interest

The authors declare no conflict of interest.

References

  1. Cias Elettronica Srl. Available online: http://www.cias.it/en/products/sensors/murena/ (accessed on 2 January 2018).
  2. Collin, R.E. Foundations for Microwave Engineering, 2nd ed.; McGraw–Hill: New York, USA, 1992; Section 6.4; ISBN 0-7803-6031-1. [Google Scholar]
  3. Valente, G.; Montisci, G.; Mariotti, S. High–performance microstrip directional coupler for radioastronomical receivers at cryogenic temperature. Electron. Lett. 2014, 50, 449–451. [Google Scholar] [CrossRef]
  4. Ladu, A.; Montisci, G.; Valente, G.; Navarrini, A.; Marongiu, P.; Pisanu, T.; Mazzarella, G. High performance cryogenic fractal 180° hybrid power divider with integrated directional coupler. Radio Sci. 2017, 52, 757–766. [Google Scholar] [CrossRef]
  5. Chen, C.C.; Kuo, J.T.; Jiang, M.; Chin, A. A Fully Planar Microstrip Coupled–line Coupler with a High Coupling Level. Microw. Opt. Technol. Lett. 2005, 46, 170–172. [Google Scholar] [CrossRef]
  6. Kim, C.S.; Kim, Y.T.; Song, S.H.; Jung, W.S.; Kank, K.Y.; Park, J.S.; Ahn, D. A Design of Microstrip Directional Coupler for High Directivity and Tight Coupling. In Proceedings of the 31st European Microwave Conference, London, UK, 24–26 September 2001; pp. 1–4. [Google Scholar] [CrossRef]
  7. Wu, Y.; Sun, W.; Leung, S.W.; Diao, Y.; Chan, K.H.; Siu, Y.M. Single–Layer Microstrip High-Directivity Coupled–Line Coupler with Tight Coupling. IEEE Trans. Microw. Theory Tech. 2013, 61, 746–753. [Google Scholar] [CrossRef]
  8. Park, M.J.; Lee, B. Compact foldable coupled line cascade couplers. IEE Proc. Microw. Antennas Propag. 2006, 153, 237–240. [Google Scholar] [CrossRef]
  9. Kirschning, M.; Jansen, R.H. Accurate Wide–Range Design Equations for the Frequency–Dependent Characteristics of Parallel Coupled Microstrip Lines. IEEE Trans. Microw. Theory Tech. 1984, 32, 83–90. [Google Scholar] [CrossRef]
  10. Mongia, R.K.; Bahl, I.J.; Bhartia, P.; Hong, J. RF and Microwave Coupled–Line Circuits, 2nd ed.; Artech House: Boston, FL, USA, 2007; Section 6.4.1; ISBN 978-1-59693-156-5. [Google Scholar]
Figure 1. Block diagram of the whole MURENA sensor (the microwave subsystem is included in a dashed box).
Figure 1. Block diagram of the whole MURENA sensor (the microwave subsystem is included in a dashed box).
Electronics 07 00025 g001
Figure 2. Structure of the proposed coupler: (a) Circuital model; (b) Microstrip realization, including test ports (dashed box shows the actual coupler size).
Figure 2. Structure of the proposed coupler: (a) Circuital model; (b) Microstrip realization, including test ports (dashed box shows the actual coupler size).
Electronics 07 00025 g002
Figure 3. Coupling C of the directional coupler in Figure 2.
Figure 3. Coupling C of the directional coupler in Figure 2.
Electronics 07 00025 g003
Figure 4. Photo of the realized prototypes. Right: directional coupler of Figure 2 with the parameters of Table 1; left: Standard quarter-wave, coupled-line-directional coupler (SC) with the same inter-line spacing S.
Figure 4. Photo of the realized prototypes. Right: directional coupler of Figure 2 with the parameters of Table 1; left: Standard quarter-wave, coupled-line-directional coupler (SC) with the same inter-line spacing S.
Electronics 07 00025 g004
Figure 5. Simulated and measured frequency response: (a) standard quarter-wave, coupled-line-directional coupler of Figure 4, left; the simulated S41 is below −40 dB (b) proposed directional coupler of Figure 4, right.
Figure 5. Simulated and measured frequency response: (a) standard quarter-wave, coupled-line-directional coupler of Figure 4, left; the simulated S41 is below −40 dB (b) proposed directional coupler of Figure 4, right.
Electronics 07 00025 g005
Figure 6. Comparison (loss efficiency η) between the proposed coupler, and the standard coupler with the same inter-line spacing.
Figure 6. Comparison (loss efficiency η) between the proposed coupler, and the standard coupler with the same inter-line spacing.
Electronics 07 00025 g006
Table 1. Geometrical parameters of the optimized coupler (see Figure 2). The optimized parameters are reported in bold.
Table 1. Geometrical parameters of the optimized coupler (see Figure 2). The optimized parameters are reported in bold.
ParameterValue
W01.7 mm
W1.4 mm
S0.15 mm
LA2.6 mm
LB4.3 mm
LC11.5 mm
LC21.6 mm
αC145 degrees
αC220 degrees
αF143 degrees
LF17.45 mm
αF245 degrees

Share and Cite

MDPI and ACS Style

Sanna, G.; Montisci, G.; Jin, Z.; Fanti, A.; Casula, G.A. Design of a Low-Cost Microstrip Directional Coupler with High Coupling for a Motion Detection Sensor. Electronics 2018, 7, 25. https://doi.org/10.3390/electronics7020025

AMA Style

Sanna G, Montisci G, Jin Z, Fanti A, Casula GA. Design of a Low-Cost Microstrip Directional Coupler with High Coupling for a Motion Detection Sensor. Electronics. 2018; 7(2):25. https://doi.org/10.3390/electronics7020025

Chicago/Turabian Style

Sanna, Giovanni, Giorgio Montisci, Zushen Jin, Alessandro Fanti, and Giovanni Andrea Casula. 2018. "Design of a Low-Cost Microstrip Directional Coupler with High Coupling for a Motion Detection Sensor" Electronics 7, no. 2: 25. https://doi.org/10.3390/electronics7020025

Note that from the first issue of 2016, this journal uses article numbers instead of page numbers. See further details here.

Article Metrics

Back to TopTop