Journal Description
Gases
Gases
is an international, peer-reviewed, open access journal on the field of applied science and engineering advances in natural gas, greenhouse gas control, and gas sensors, published quarterly online by MDPI.
- Open Access— free for readers, with article processing charges (APC) paid by authors or their institutions.
- Rapid Publication: first decisions in 16 days; acceptance to publication in 5.8 days (median values for MDPI journals in the second half of 2023).
- Recognition of Reviewers: APC discount vouchers, optional signed peer review, and reviewer names published annually in the journal.
- Gases is a companion journal of Energies.
Latest Articles
Carbon Dioxide Capture under Low-Pressure Low-Temperature Conditions Using Shaped Recycled Fly Ash Particles
Gases 2024, 4(2), 117-132; https://doi.org/10.3390/gases4020007 (registering DOI) - 23 May 2024
Abstract
Carbon-capture technologies are extremely abundant, yet they have not been applied extensively worldwide due to their high cost and technological complexities. This research studies the ability of polymerized fly ash to capture carbon dioxide (CO2) under low-pressure and low-temperature conditions via
[...] Read more.
Carbon-capture technologies are extremely abundant, yet they have not been applied extensively worldwide due to their high cost and technological complexities. This research studies the ability of polymerized fly ash to capture carbon dioxide (CO2) under low-pressure and low-temperature conditions via physical adsorption. The research also studies the ability to desorb CO2 due to the high demand for CO2 in different industries. The adsorption–desorption hysteresis was measured using infrared-sensor detection apparatus. The impact of the CO2 injection rate for adsorption, helium injection rate for desorption, temperature, and fly ash contact surface area on the adsorption–desorption hysteresis was investigated. The results showed that change in the CO2 injection rate had little impact on the variation in the adsorption capacity; for all CO2 rate experiments, the adsorption reached more than 90% of the total available adsorption sites. Increasing the temperature caused the polymerized fly ash to expand, thus increasing the available adsorption sites, thus increasing the overall adsorption volume. At low helium rates, desorption was extremely lengthy which resulted in a delayed hysteresis response. This is not favorable since it has a negative impact on the adsorption–desorption cyclic rate. Based on the results, the polymerized fly ash proved to have a high CO2 capture capability and thus can be applied for carbon-capture applications.
Full article
(This article belongs to the Topic Carbon Dioxide Capture or Removal and Valorisation: Advances in the Development of Materials and Technologies)
Open AccessArticle
Combustion Diagnosis in a Spark-Ignition Engine Fueled with Syngas at Different CO/H2 and Diluent Ratios
by
Santiago Martinez-Boggio, Pedro Teixeira Lacava, Felipe Solferini de Carvalho and Pedro Curto-Risso
Gases 2024, 4(2), 97-116; https://doi.org/10.3390/gases4020006 - 15 May 2024
Abstract
The gasification of residues into syngas offers a versatile gaseous fuel that can be used to produce heat and power in various applications. However, the application of syngas in engines presents several challenges due to the changes in its composition. Such variations can
[...] Read more.
The gasification of residues into syngas offers a versatile gaseous fuel that can be used to produce heat and power in various applications. However, the application of syngas in engines presents several challenges due to the changes in its composition. Such variations can significantly alter the optimal operational conditions of the engines that are fueled with syngas, resulting in combustion instability, high engine variability, and misfires. In this context, this work presents an experimental investigation conducted on a port-fuel injection spark-ignition optical research engine using three different syngas mixtures, with a particular focus on the effects of CO/H2 and diluent ratios. A comparative analysis is made against methane, considered as the baseline fuel. The in-cylinder pressure and related parameters are examined as indicators of combustion behavior. Additionally, 2D cycle-resolved digital visualization is employed to trace flame front propagation. Custom image processing techniques are applied to estimate flame speed, displacement, and morphological parameters. The engine runs at a constant speed (900 rpm) and with full throttle like stationary engine applications. The excess air–fuel ratios vary from 1.0 to 1.4 by adjusting the injection time and the spark timing according to the maximum brake torque of the baseline fuel. A thermodynamic analysis revealed notable trends in in-cylinder pressure traces, indicative of differences in combustion evolution and peak pressures among the syngas mixtures and methane. Moreover, the study quantified parameters such as the mass fraction burned, combustion stability (COVIMEP), and fuel conversion efficiency. The analysis provided insights into flame morphology, propagation speed, and distortion under varying conditions, shedding light on the influence of fuel composition and air dilution. Overall, the results contribute to advancing the understanding of syngas combustion behavior in SI engines and hold implications for optimizing engine performance and developing numerical models.
Full article
(This article belongs to the Special Issue Bio-Energy: Biogas, Biomethane and Green-Hydrogen)
►▼
Show Figures
Figure 1
Open AccessArticle
Transitioning to a Hydrogen Economy: Exploring the Viability of Adapting Natural Gas Pipelines for Hydrogen Transport through a Case Study on Compression vs. Looping
by
Abubakar Jibrin Abbas, Salisu Kwalami Haruna, Martin Burby, Idoko Job John and Kabir Hassan Yar’Adua
Gases 2024, 4(2), 74-96; https://doi.org/10.3390/gases4020005 - 30 Apr 2024
Abstract
►▼
Show Figures
The growing importance of hydrogen as an energy carrier in a future decarbonised energy system has led to a surge in its production plans. However, the development of infrastructure for hydrogen delivery, particularly in the hard-to-abate sectors, remains a significant challenge. While constructing
[...] Read more.
The growing importance of hydrogen as an energy carrier in a future decarbonised energy system has led to a surge in its production plans. However, the development of infrastructure for hydrogen delivery, particularly in the hard-to-abate sectors, remains a significant challenge. While constructing new pipelines entails substantial investment, repurposing existing pipelines offers a cost-effective approach to jump-starting hydrogen networks. Many European countries and, more recently, other regions are exploring the possibility of utilising their current pipeline infrastructure for hydrogen transport. Despite the recent efforts to enhance the understanding of pipeline compatibility and integrity for hydrogen transportation, including issues such as embrittlement, blend ratios, safety concerns, compressor optimisation, and corrosion in distribution networks, there has been limited or no focus on pipeline expansion options to address the low-energy density of hydrogen blends and associated costs. This study, therefore, aims to explore expansion options for existing natural gas high-pressure pipelines through additional compression or looping. It seeks to analyse the corresponding cost implications to achieve an affordable and sustainable hydrogen economy by investigating the utilisation of existing natural gas pipeline infrastructure for hydrogen transportation as a cost-saving measure. It explores two expansion strategies, namely pipeline looping (also known as pipeline reinforcement) and compression, for repurposing a segment of a 342 km × 36 inch existing pipeline, from the Escravos–Lagos gas pipeline system (ELPS) in Nigeria, for hydrogen transport. Employing the Promax® process simulator tool, the study assesses compliance with the API RP 14E and ASME B31.12 standards for hydrogen and hydrogen–methane blends. Both expansion strategies demonstrate acceptable velocity and pressure drop characteristics for hydrogen blends of up to 40%. Additionally, the increase in hydrogen content leads to heightened compression power requirements until approximately 80% hydrogen in the blends for compression and a corresponding extension in looping length until around 80% hydrogen in the blend for looping. Moreover, the compression option is more economically viable for all investigated proportions of hydrogen blends for the PS1–PS5 segment of the Escravos–Lagos gas pipeline case study. The percentage price differentials between the two expansion strategies reach as high as 495% for a 20% hydrogen proportion in the blend. This study offers valuable insights into the technical and economic implications of repurposing existing natural gas infrastructure for hydrogen transportation.
Full article
Figure 1
Open AccessArticle
Towards the Isothermal Gas Compression—A Novel Finned Piston-Cylinder with Increased Efficiency
by
Alfred Rufer
Gases 2024, 4(2), 59-73; https://doi.org/10.3390/gases4020004 - 8 Apr 2024
Abstract
►▼
Show Figures
In this paper, a novel concept of a finned piston system is presented and analyzed in which the compression heat is continuously extracted from the compression chamber. The resulting compression characteristic moves in the direction of an isothermal process, reducing the temperature of
[...] Read more.
In this paper, a novel concept of a finned piston system is presented and analyzed in which the compression heat is continuously extracted from the compression chamber. The resulting compression characteristic moves in the direction of an isothermal process, reducing the temperature of the compressed fluid in the compression chamber and reducing the necessary mechanical work required to carry out the process. The finned piston concept consists in an integrated heat exchanger inside of the chamber that is constituted of imbricated flat fins placed on the stator part and on the mobile piston. The internal heat exchange on the surface is strongly increased in comparison with a classical piston/cylinder. The energetic performance of the new system is evaluated with the help of simulation. The pressures, forces, and temperature of the compressed gas are simulated as well as the mechanical work needed. The different curves are compared with the system’s adiabatic and isothermal characteristics.
Full article
Figure 1
Open AccessArticle
Thermodynamic Analysis of Low-Emission Offshore Gas-to-Wire Firing CO2-Rich Natural Gas: Aspects of Carbon Capture and Separation Systems
by
Alessandra de Carvalho Reis, Ofélia de Queiroz Fernandes Araújo and José Luiz de Medeiros
Gases 2024, 4(2), 41-58; https://doi.org/10.3390/gases4020003 - 25 Mar 2024
Abstract
►▼
Show Figures
Despite the growth of renewable energy, fossil fuels dominate the global energy matrix. Due to expanding proved reserves and energy demand, an increase in natural gas power generation is predicted for future decades. Oil reserves from the Brazilian offshore Pre-Salt basin have a
[...] Read more.
Despite the growth of renewable energy, fossil fuels dominate the global energy matrix. Due to expanding proved reserves and energy demand, an increase in natural gas power generation is predicted for future decades. Oil reserves from the Brazilian offshore Pre-Salt basin have a high gas-to-oil ratio of CO2-rich associated gas. To deliver this gas to market, high-depth long-distance subsea pipelines are required, making Gas-to-Pipe costly. Since it is easier to transport electricity through long subsea distances, Gas-to-Wire instead of Gas-to-Pipe is a more convenient alternative. Aiming at making offshore Gas-to-Wire thermodynamically efficient without impacting CO2 emissions, this work explores a new concept of an environmentally friendly and thermodynamically efficient Gas-to-Wire process firing CO2-rich natural gas (CO2 > 40%mol) from high-depth offshore oil and gas fields. The proposed process prescribes a natural gas combined cycle, exhaust gas recycling (lowering flue gas flowrate and increasing flue gas CO2 content), CO2 post-combustion capture with aqueous monoethanolamine, and CO2 dehydration with triethylene glycol for enhanced oil recovery. The two main separation processes (post-combustion carbon capture and CO2 dehydration) have peculiarities that were addressed at the light shed by thermodynamic analysis. The overall process provides 534.4 MW of low-emission net power. Second law analysis shows that the thermodynamic efficiency of Gas-to-Wire with carbon capture attains 33.35%. Lost-Work analysis reveals that the natural gas combined cycle sub-system is the main power destruction sink (80.7% Lost-Work), followed by the post-combustion capture sub-system (14% Lost-Work). These units are identified as the ones that deserve to be upgraded to rapidly raise the thermodynamic efficiency of the low-emission Gas-to-Wire process.
Full article
Figure 1
Open AccessReview
A Review on the Process of Greenhouse Gas Inventory Preparation and Proposed Mitigation Measures for Reducing Carbon Footprint
by
Cevat Yaman
Gases 2024, 4(1), 18-40; https://doi.org/10.3390/gases4010002 - 15 Mar 2024
Abstract
►▼
Show Figures
Greenhouse gases trap heat in the atmosphere, causing the Earth’s surface temperature to rise. The main greenhouse gases are carbon dioxide, methane, nitrous oxide, perfluorocarbons, hydrofluorocarbons, and sulfur hexafluoride. Human activities are increasing greenhouse gas concentrations rapidly, which is causing global climate change.
[...] Read more.
Greenhouse gases trap heat in the atmosphere, causing the Earth’s surface temperature to rise. The main greenhouse gases are carbon dioxide, methane, nitrous oxide, perfluorocarbons, hydrofluorocarbons, and sulfur hexafluoride. Human activities are increasing greenhouse gas concentrations rapidly, which is causing global climate change. Global climate change is increasing environmental and public health problems. To reduce greenhouse gas emissions, it is necessary to identify where the emissions are coming from, develop a plan to reduce them, and then implement and monitor the plan to ensure that emissions are actually reduced. Anthropogenic global climate change has large and increasingly adverse economic effects. Cities emit the most greenhouse gas due to fossil fuel burning and power usage. The four major greenhouse gas emitters are energy, transportation, waste management, and urban land use sectors. Organizations should prepare action plans to lower their greenhouse gas emissions and stop the worst consequences of climate change. These action plans require companies and local authorities to submit their greenhouse gas emissions reports on a yearly basis. A greenhouse gas emissions management system includes several processes and tools created by organizations to understand, measure, monitor, report, and validate their greenhouse gas emissions. Two of the most widely adapted frameworks for greenhouse gases inventory reporting are ISO 14064 and the greenhouse gas protocol. This review paper aims to identify some of the key points of GHG inventory preparation and mitigation strategies.
Full article
Figure 1
Open AccessArticle
Natural Gas Matters: LNG and India’s Quest for Clean Energy
by
Subhadip Ghosh, Rajarshi Majumder and Bidisha Chatterjee
Gases 2024, 4(1), 1-17; https://doi.org/10.3390/gases4010001 - 3 Feb 2024
Abstract
India, the world’s most populous country, is the world’s third-largest emitter of greenhouse gases (GHGs). Despite employing several energy sources, it still relies heavily on coal, its primary energy source. Given India’s swiftly rising energy demand, this challenges meeting emission reduction targets. In
[...] Read more.
India, the world’s most populous country, is the world’s third-largest emitter of greenhouse gases (GHGs). Despite employing several energy sources, it still relies heavily on coal, its primary energy source. Given India’s swiftly rising energy demand, this challenges meeting emission reduction targets. In recent years, India has significantly increased investments in renewables like solar and hydrogen. While commendable, these initiatives alone cannot meet the country’s expanding energy demands. In the short term, India must rely on both domestic and imported fossil fuels, with natural gas being the most environmentally friendly option. In this context, this paper attempts to forecast energy consumption, natural gas production, and consumption in India until 2050, using both univariate and multivariate forecasting methods. For multivariate forecasting, we have assumed two alternative possibilities for GDP growth: the business-as-usual and the high-growth scenarios. Each of our forecasts indicates a notable shortfall in the projected production of natural gas compared to the expected demand, implying our results are robust. Our model predicts that nearly 30–50 percent of India’s natural gas consumption will be met by imports, mainly in the form of LNG. Based on these findings, this paper recommends that Indian government policies emphasize increasing domestic natural gas production, importing LNG, and expanding renewable energy resources.
Full article
(This article belongs to the Section Natural Gas)
►▼
Show Figures
Figure 1
Open AccessEditorial
Helium: Sources, Applications, Supply, and Demand
by
Juan Sebastian Serra Leal, Jimena Incer-Valverde and Tatiana Morosuk
Gases 2023, 3(4), 181-183; https://doi.org/10.3390/gases3040013 - 6 Dec 2023
Abstract
Helium is an inert gas with no color or odor [...]
Full article
Open AccessArticle
Greenhouse Gas Conversion into Hydrocarbons and Oxygenates Using Low Temperature Barrier Discharge Plasma Combined with Zeolite Catalysts
by
Oleg V. Golubev, Dmitry E. Tsaplin and Anton L. Maximov
Gases 2023, 3(4), 165-180; https://doi.org/10.3390/gases3040012 - 5 Dec 2023
Abstract
Global warming occurs as a result of the build-up of greenhouse gases in the atmosphere, causing an increase in Earth’s average temperature. Two major greenhouse gases (CH4 and CO2) can be simultaneously converted into value-added chemicals and fuels thereby decreasing
[...] Read more.
Global warming occurs as a result of the build-up of greenhouse gases in the atmosphere, causing an increase in Earth’s average temperature. Two major greenhouse gases (CH4 and CO2) can be simultaneously converted into value-added chemicals and fuels thereby decreasing their negative impact on the climate. In the present work, we used a plasma-catalytic approach for the conversion of methane and carbon dioxide into syngas, hydrocarbons, and oxygenates. For this purpose, CuCe zeolite-containing catalysts were prepared and characterized (low-temperature N2 adsorption, XRF, XRD, CO2-TPD, NH3-TPD, TPR). The process of carbon dioxide methane reforming was conducted in a dielectric barrier discharge under atmospheric pressure and at low temperature (under 120 °C). It was found that under the studied conditions, the major byproducts of CH4 reforming are CO, H2, and C2H6 with the additional formation of methanol and acetone. The application of a ZSM-12 based catalyst was beneficial as the CH4 conversion increased and the total concentration of liquid products was the highest, which is related to the acidic properties of the catalyst.
Full article
(This article belongs to the Section Gas Emissions)
►▼
Show Figures
Figure 1
Open AccessOpinion
Alternative Gaseous Fuels for Marine Vessels towards Zero-Carbon Emissions
by
Cherng-Yuan Lin, Pei-Chi Wu and Hsuan Yang
Gases 2023, 3(4), 158-164; https://doi.org/10.3390/gases3040011 - 17 Nov 2023
Abstract
The maritime industry is recognized as a major pollution source to the environment. The use of low- or zero-carbon marine alternative fuel is a promising measure to reduce emissions of greenhouse gases and toxic pollutants, leading to net-zero carbon emissions by 2050. Hydrogen
[...] Read more.
The maritime industry is recognized as a major pollution source to the environment. The use of low- or zero-carbon marine alternative fuel is a promising measure to reduce emissions of greenhouse gases and toxic pollutants, leading to net-zero carbon emissions by 2050. Hydrogen (H2), fuel cells particularly proton exchange membrane fuel cell (PEMFC), and ammonia (NH3) are screened out to be the feasible marine gaseous alternative fuels. Green hydrogen can reduce the highest carbon emission, which might amount to 100% among those 5 types of hydrogen. The main hurdles to the development of H2 as a marine alternative fuel include its robust and energy-consuming cryogenic storage system, highly explosive characteristics, economic transportation issues, etc. It is anticipated that fossil fuel used for 35% of vehicles such as marine vessels, automobiles, or airplanes will be replaced with hydrogen fuel in Europe by 2040. Combustible NH3 can be either burned directly or blended with H2 or CH4 to form fuel mixtures. In addition, ammonia is an excellent H2 carrier to facilitate its production, storage, transportation, and usage. The replacement of promising alternative fuels can move the marine industry toward decarbonization emissions by 2050.
Full article
Open AccessArticle
Influence of Hydrogen on the Performance and Emissions Characteristics of a Spark Ignition Ammonia Direct Injection Engine
by
Cheolwoong Park, Yonghun Jang, Seonyeob Kim, Yongrae Kim and Young Choi
Gases 2023, 3(4), 144-157; https://doi.org/10.3390/gases3040010 - 16 Oct 2023
Cited by 1
Abstract
Because ammonia is easier to store and transport over long distances than hydrogen, it is a promising research direction as a potential carrier for hydrogen. However, its low ignition and combustion rates pose challenges for running conventional ignition engines solely on ammonia fuel
[...] Read more.
Because ammonia is easier to store and transport over long distances than hydrogen, it is a promising research direction as a potential carrier for hydrogen. However, its low ignition and combustion rates pose challenges for running conventional ignition engines solely on ammonia fuel over the entire operational range. In this study, we attempted to identify a stable engine combustion zone using a high-pressure direct injection of ammonia fuel into a 2.5 L spark ignition engine and examined the potential for extending the operational range by adding hydrogen. As it is difficult to secure combustion stability in a low-temperature atmosphere, the experiment was conducted in a sufficiently-warmed atmosphere (90 ± 2.5 °C), and the combustion, emission, and efficiency results under each operating condition were experimentally compared. At 1500 rpm, the addition of 10% hydrogen resulted in a notable 20.26% surge in the maximum torque, reaching 263.5 Nm, in contrast with the case where only ammonia fuel was used. Furthermore, combustion stability was ensured at a torque of 140 Nm by reducing the fuel and air flow rates.
Full article
(This article belongs to the Special Issue Gas Emissions from Combustion Sources)
►▼
Show Figures
Figure 1
Open AccessCommunication
Effect of Mixing Technique on Physico-Chemical Characteristics of Blended Membranes for Gas Separation
by
Danial Qadir, Humbul Suleman and Faizan Ahmad
Gases 2023, 3(4), 136-143; https://doi.org/10.3390/gases3040009 - 26 Sep 2023
Abstract
Polymer blending has attracted considerable attention because of its ability to overcome the permeability–selectivity trade-off in gas separation applications. In this study, polysulfone (PSU)-modified cellulose acetate (CA) membranes were prepared using N-methyl-2-pyrrolidone (NMP) and tetrahydrofuran (THF) using a dry–wet phase inversion technique.
[...] Read more.
Polymer blending has attracted considerable attention because of its ability to overcome the permeability–selectivity trade-off in gas separation applications. In this study, polysulfone (PSU)-modified cellulose acetate (CA) membranes were prepared using N-methyl-2-pyrrolidone (NMP) and tetrahydrofuran (THF) using a dry–wet phase inversion technique. The membranes were characterized using scanning electron microscopy (SEM) for morphological analysis, thermogravimetric analysis (TGA) for thermal stability, and Fourier transform infrared spectroscopy (FTIR) to identify the chemical changes on the surface of the membranes. Our analyses confirmed that the mixing method (the route chosen for preparing the casting solution for the blended membranes) significantly influences the morphological and thermal properties of the resultant membranes. The blended membranes exhibited a transition from a finger-like pore structure to a dense substructure in the presence of macrovoids. Similarly, thermal analysis confirmed the improved residual weight (up to 7%) and higher onset degradation temperature (up to 10 °C) of the synthesized membranes. Finally, spectral analysis confirmed that the blending of both polymers was physical only.
Full article
(This article belongs to the Special Issue Membrane Processes for Decarbonisation)
►▼
Show Figures
Graphical abstract
Open AccessArticle
Experimental Study and Thermodynamic Analysis of Carbon Dioxide Adsorption onto Activated Carbons Prepared from Biowaste Raw Materials
by
Olga V. Solovtsova, Ilya E. Men’shchikov, Andrey V. Shkolin, Alexander E. Grinchenko, Elena V. Khozina and Anatoly A. Fomkin
Gases 2023, 3(3), 112-135; https://doi.org/10.3390/gases3030008 - 14 Aug 2023
Abstract
►▼
Show Figures
Nutshells are regarded as cost-effective and abundant raw materials for producing activated carbons (ACs) for CO2 capture, storage, and utilization. The effects of carbonization temperature and thermochemical KOH activation conditions on the porous structure as a BET surface, micropore volume, micropore width,
[...] Read more.
Nutshells are regarded as cost-effective and abundant raw materials for producing activated carbons (ACs) for CO2 capture, storage, and utilization. The effects of carbonization temperature and thermochemical KOH activation conditions on the porous structure as a BET surface, micropore volume, micropore width, and pore size distribution of ACs prepared from walnut (WNS) and hazelnut (HNS) shells were investigated. As a result, one-step carbonization at 900/800 °C and thermochemical KOH activation with a char/KOH mass ratio of 1:2/1:3 were found to be optimal for preparing ACs from WNS/HNS: WNS-AC-3 and HNS-AC-2, respectively. The textural properties of the WNS/HNS chars and ACs were characterized by low-temperature nitrogen vapor adsorption, XRD, and SEM methods. Dubinin’s theory of volume filling of micropores was used to evaluate the microporosity parameters and to calculate the CO2 adsorption equilibrium over the sub- and supercritical temperatures from 216.4 to 393 K at a pressure up to 10 MPa. The CO2 capture capacities of WNS- and HNS-derived adsorbents reached 5.9/4.1 and 5.4/3.9 mmol/g at 273/293 K under 0.1 MPa pressure, respectively. A discrepancy between the total and delivery volumetric adsorption capacities of the adsorbents was attributed to the strong binding of CO2 molecules with the adsorption sites, which were mainly narrow micropores with a high adsorption potential. The high initial differential heats of CO2 adsorption onto ACs of ~32 kJ/mol confirmed this proposal. The behaviors of thermodynamic functions (enthalpy and entropy) of the adsorption systems were attributed to changes in the state of adsorbed CO2 molecules determined by a balance between attractive and repulsive CO2–CO2 and CO2–AC interactions during the adsorption process. Thus, the chosen route for preparing ACs from the nutshells made it possible to prepare efficient carbon adsorbents with a relatively high CO2 adsorption performance due to a substantial volume of micropores with a size in the range of 0.6–0.7 nm.
Full article
Figure 1
Open AccessCommunication
A New Ignition Source for the Determination of Safety Characteristics of Gases
by
Stefan H. Spitzer, Gerald Riesner, Sabine Zakel and Carola Schierding
Gases 2023, 3(3), 106-111; https://doi.org/10.3390/gases3030007 - 3 Jul 2023
Abstract
►▼
Show Figures
Safety characteristics are used to keep processes, including flammable gases, vapors, and combustible dusts, safe. In the standards for the determination of safety characteristics of gases and vapors, the induction spark is commonly used. However, classic transformers are hard to obtain, and replacement
[...] Read more.
Safety characteristics are used to keep processes, including flammable gases, vapors, and combustible dusts, safe. In the standards for the determination of safety characteristics of gases and vapors, the induction spark is commonly used. However, classic transformers are hard to obtain, and replacement with new electronic transformers is not explicitly allowed in the standards. This article presents the investigation of five gases that are normally used to calibrate devices for the determination of safety characteristics, the maximum experimental safe gap (MESG), with an electronic transformer, and the values are compared to the ones that are obtained with the standard transformer. Additionally, calorimetric measurements on the net energy of both ignition sources were performed as well as open-circuit voltage measurements. It is concluded that the classic type of transformer can be replaced by the new type obtaining the same results for the MESG and introducing the same amount of energy into the system.
Full article
Figure 1
Open AccessArticle
Hydrogen Purification through a Membrane–Cryogenic Integrated Process: A 3 E’s (Energy, Exergy, and Economic) Assessment
by
Ahmad Naquash, Amjad Riaz, Fatma Yehia, Yus Donald Chaniago, Hankwon Lim and Moonyong Lee
Gases 2023, 3(3), 92-105; https://doi.org/10.3390/gases3030006 - 27 Jun 2023
Cited by 2
Abstract
Hydrogen (H2) is known for its clean energy characteristics. Its separation and purification to produce high-purity H2 is becoming essential to promoting a H2 economy. There are several technologies, such as pressure swing adsorption, membrane, and cryogenic, which can
[...] Read more.
Hydrogen (H2) is known for its clean energy characteristics. Its separation and purification to produce high-purity H2 is becoming essential to promoting a H2 economy. There are several technologies, such as pressure swing adsorption, membrane, and cryogenic, which can be adopted to produce high-purity H2; however, each standalone technology has its own pros and cons. Unlike standalone technology, the integration of technologies has shown significant potential for achieving high purity with a high recovery. In this study, a membrane–cryogenic process was integrated to separate H2 via the desublimation of carbon dioxide. The proposed process was designed, simulated, and optimized in Aspen Hysys. The results showed that the H2 was separated with a 99.99% purity. The energy analysis revealed a net-specific energy consumption of 2.37 kWh/kg. The exergy analysis showed that the membranes and multi-stream heat exchangers were major contributors to the exergy destruction. Furthermore, the calculated total capital investment of the proposed process was 816.2 m$. This proposed process could be beneficial for the development of a H2 economy.
Full article
(This article belongs to the Special Issue Membrane Processes for Decarbonisation)
►▼
Show Figures
Figure 1
Open AccessArticle
Computational Fluid Dynamics Analysis of a Hollow Fiber Membrane Module for Binary Gas Mixture
by
Salman Qadir, Muhammad Ahsan and Arshad Hussain
Gases 2023, 3(2), 77-91; https://doi.org/10.3390/gases3020005 - 22 May 2023
Cited by 1
Abstract
The membrane gas separation process has gained significant attention using the computational fluid dynamics (CFD) technique. This study considered the CFD method to find gas concentration profiles in a hollow fiber membrane (HFM) module to separate the binary gas mixture. The membrane was
[...] Read more.
The membrane gas separation process has gained significant attention using the computational fluid dynamics (CFD) technique. This study considered the CFD method to find gas concentration profiles in a hollow fiber membrane (HFM) module to separate the binary gas mixture. The membrane was considered with a fiber thickness where each component’s mass fluxes could be obtained based on the local partial pressures, solubility, diffusion, and the membrane’s selectivity. COMSOL Multiphysics was used to solve the numerical solution at corresponding operating conditions and results were compared to experimental data. The two different mixtures, CO2/CH4 and N2/O2, were investigated to obtain concentration gradient and mass flux profiles of CO2 and O2 species in an axial direction. This study allows assessing the feed pressure’s impact on the HFM system’s overall performance. These results demonstrate that the increment in feed pressures decreased the membrane system’s separation performance. The impact of hollow fiber length indicates that increasing the active fiber length has a higher effective mass transfer region but dilutes the permeate-side purities of O2 (46% to 28%) and CO2 (93% to 73%). The results show that increasing inlet pressure and a higher concentration gradient resulted in higher flux through the membrane.
Full article
(This article belongs to the Special Issue Membrane Processes for Decarbonisation)
►▼
Show Figures
Figure 1
Open AccessArticle
Assessment of the Reverberations Caused by Predominant Air Pollutants on Urban Vegetation: A Multi-Site Study in Varanasi Located in Indo-Gangetic Plains
by
Harshita Singh, Pallavi Singh, Shashi Bhushan Agrawal and Madhoolika Agrawal
Gases 2023, 3(2), 57-76; https://doi.org/10.3390/gases3020004 - 5 Apr 2023
Cited by 2
Abstract
Plant responses to air pollution have been extensively studied in urban environments. Nevertheless, detailed and holistic studies assessing their retaliation to air contaminants are still limited. The present study evaluates the effect of criteria pollutants (SO2, NO2, PM10
[...] Read more.
Plant responses to air pollution have been extensively studied in urban environments. Nevertheless, detailed and holistic studies assessing their retaliation to air contaminants are still limited. The present study evaluates the effect of criteria pollutants (SO2, NO2, PM10 and O3) on the overall biochemistry and resource allocation strategy of plants in order to categorize the dominant roadside species (Mangifera indica, Psidium guajava, Ficus religiosa, Azadirachta indica, Dalbergia sissoo, Cascabela thevetia and Bougainvillea spectabilis) of the Indo-Gangetic Plains (IGP), with different morphologies and habits, into species that are tolerant and sensitive to the prevailing air pollutants. This study was performed at three different land-use sites (industrial, commercial and reference) in Varanasi for two seasons (summer and winter). It was inferred that NO2 and PM10 consistently violated the air quality standards at all the sites. The fifteen assessed parameters reflected significant variations depending upon the site, season and plant species whereupon the enzymatic antioxidants (superoxide dismutase and catalase) and resource utilization parameters (leaf area and leaf dry matter content) were remarkably affected. Based on the studied parameters, it was entrenched that deciduous tree species with compound leaves (D. sissoo > A. indica) were identified as the less sensitive, followed by a shrub (C. thevetia > B. spectabilis), while evergreen species with simple leaves were the most sensitive. It was also substantiated that the morphology of the foliage contributed more toward the differential response of the plants to air pollutants than its habit.
Full article
(This article belongs to the Special Issue Air Quality: Monitoring and Assessment)
►▼
Show Figures
Figure 1
Open AccessArticle
Greenhouse Gas Emissions of the Poultry Sector in Greece and Mitigation Potential Strategies
by
Konstantina Akamati, George P. Laliotis and Iosif Bizelis
Gases 2023, 3(1), 47-56; https://doi.org/10.3390/gases3010003 - 14 Mar 2023
Cited by 1
Abstract
►▼
Show Figures
The poultry sector is considered to be one of the most industrialized sectors of livestock production. Although the livestock sector contributes the 14.5% of total anthropogenic greenhouse gas (GHG) emissions, less attention has been paid in the respective emissions of the poultry sector
[...] Read more.
The poultry sector is considered to be one of the most industrialized sectors of livestock production. Although the livestock sector contributes the 14.5% of total anthropogenic greenhouse gas (GHG) emissions, less attention has been paid in the respective emissions of the poultry sector compared to other farmed animals such as ruminants. The aim of the study was to estimate the carbon footprint of the poultry sector (layers, broilers, and backyards) in the Greek territory during the last 60 years as a means of exploring further mitigation strategies. Tier 2 methodology was used to estimate GHG emissions. Different mitigation scenarios related to changes in herd population, feeds, and manure management were examined. GHG emissions showed an increased trend over time. The different scenarios explored showed moderate to high mitigating potential depending on the parameters that were changed. Changes in manure management or diet revealed to have a higher potential to eliminate GHG emissions. Changes in population numbers showed a low mitigating potential. However, if mortality could be improved within industrialized farming systems, then it could be an indirect increase in product quantities with a slight increase in emissions. Therefore, depending on national priorities, the sector could improve its environmental impact by targeting aspects related to husbandry/management practices.
Full article
Figure 1
Open AccessReview
The Hydrogen Color Spectrum: Techno-Economic Analysis of the Available Technologies for Hydrogen Production
by
Jose M. Marín Arcos and Diogo M. F. Santos
Gases 2023, 3(1), 25-46; https://doi.org/10.3390/gases3010002 - 3 Feb 2023
Cited by 38
Abstract
►▼
Show Figures
Hydrogen has become the most promising energy carrier for the future. The spotlight is now on green hydrogen, produced with water electrolysis powered exclusively by renewable energy sources. However, several other technologies and sources are available or under development to satisfy the current
[...] Read more.
Hydrogen has become the most promising energy carrier for the future. The spotlight is now on green hydrogen, produced with water electrolysis powered exclusively by renewable energy sources. However, several other technologies and sources are available or under development to satisfy the current and future hydrogen demand. In fact, hydrogen production involves different resources and energy loads, depending on the production method used. Therefore, the industry has tried to set a classification code for this energy carrier. This is done by using colors that reflect the hydrogen production method, the resources consumed to produce the required energy, and the number of emissions generated during the process. Depending on the reviewed literature, some colors have slightly different definitions, thus making the classifications imprecise. Therefore, this techno-economic analysis clarifies the meaning of each hydrogen color by systematically reviewing their production methods, consumed energy sources, and generated emissions. Then, an economic assessment compares the costs of the various hydrogen colors and examines the most feasible ones and their potential evolution. The scientific community and industry’s clear understanding of the advantages and drawbacks of each element of the hydrogen color spectrum is an essential step toward reaching a sustainable hydrogen economy.
Full article
Graphical abstract
Open AccessReview
A Review on Qualitative Assessment of Natural Gas Utilisation Options for Eliminating Routine Nigerian Gas Flaring
by
Robin Abu, Kumar Patchigolla and Nigel Simms
Gases 2023, 3(1), 1-24; https://doi.org/10.3390/gases3010001 - 28 Jan 2023
Cited by 8
Abstract
►▼
Show Figures
Natural gas flaring, with its harmful environmental, health, and economic effects, is common in the Nigerian oil and gas industry because of a lower tax regime for flared gases. Based on the adverse effects of flared gas, the Nigerian government has renewed and
[...] Read more.
Natural gas flaring, with its harmful environmental, health, and economic effects, is common in the Nigerian oil and gas industry because of a lower tax regime for flared gases. Based on the adverse effects of flared gas, the Nigerian government has renewed and improved its efforts to reduce or eliminate gas flaring through the application of natural gas utilisation techniques. However, because the conventional approach to flare gas utilisation is heavily reliant on achieving scale, fuel, and end-product prices, not all technologies are technically and economically viable for typically capturing large and small quantities of associated gas from various flare sites or gas fields (located offshore or onshore). For these reasons, this paper reviews and compares various flare gas utilisation options to guide their proper selection for appropriate implementation in the eradication of routine gas flaring in Nigeria and to promote the Zero Routine Flaring initiative, which aims to reduce flaring levels dramatically by 2030. A qualitative assessment is used in this study to contrast the various flare gas utilisation options against key decision drivers. In this analysis, three natural gas utilisation processes—liquefied natural gas (LNG), gas to wire (GTW), and gas to methanol (GTM)—are recommended as options for Nigeria because of their economic significance, technological viability (both onshore and offshore), and environmental benefits. All these gas utilisation options have the potential to significantly reduce and prevent routine gas flaring in Nigeria and can be used separately or in combination to create synergies that could lower project costs and product market risk. This article clearly identifies the environmental benefits and the technical and economic viability of infrastructure investments to recover and repurpose flare gasses along with recommendation steps to select and optimise economies of scale for an associated natural gas utilisation option.
Full article
Figure 1
Highly Accessed Articles
Latest Books
E-Mail Alert
News
Topics
Topic in
Energies, Gases, Geosciences, Minerals
Microstructural Analysis of Organic Matter in Shale
Topic Editors: Kouqi Liu, Mehdi OstadhassanDeadline: 30 June 2024
Topic in
Energies, JMSE, Materials, Minerals, Molecules, Gases
Formation, Exploration and Development of Natural Gas Hydrate
Topic Editors: Lunxiang Zhang, Hongsheng DongDeadline: 31 July 2024
Topic in
Catalysts, Clean Technol., Energies, Gases, Sustainability
Carbon Dioxide Capture or Removal and Valorisation: Advances in the Development of Materials and Technologies
Topic Editors: Paula Teixeira, María Pilar Lisbona, Carmen BacarizaDeadline: 30 November 2024
Conferences
Special Issues
Special Issue in
Gases
Gas Emissions from Combustion Sources
Guest Editors: Cinzia Tornatore, Andrea De FilippoDeadline: 30 June 2024
Special Issue in
Gases
Smart Gas Sensors
Guest Editors: Praveen Sekhar, Alessia Di GilioDeadline: 15 September 2024
Special Issue in
Gases
Editorial Board Members' Collection Series: Actions to Keep Global Warming in 1.5 Degrees
Guest Editors: Ben J. Anthony, Paola AmmendolaDeadline: 31 December 2024