Search Results (27)

Solid-state lighting, especially light-emitting diodes (LEDs), is revolutionizing indoor lighting due to its energy efficiency, long lifespan, low heat output, and enhanced color rendering. LEDs can quickly adjust light intensity, enabling the development of visible light communication (VLC) technology. However, the modulation bandwidth of phosphor-converted white LEDs commonly used for illumination is limited, potentially affecting the speed of the VLC links. This paper presents a receiver-side equalization technique to overcome bandwidth limitations in VLC links due to LEDs. The proposed approach utilizes a novel transimpedance amplifier with an embedded T-network shunt-feedback equalizer (TIA-TE) to introduce adjustable high-frequency peaking in the TIA’s frequency response. By incorporating this peaking, the system’s bandwidth is extended without sacrificing important performance parameters like gain, noise, or power dissipation. The TIA-TE is followed by a main amplifier and a standalone continuous-time linear equalizer (CTLE) for further signal conditioning, while a 50 Ω buffer interfaces the receiver with measurement equipment. Post-layout simulations in a 0.35 µm CMOS process validate the approach. Using a 4 pF photodiode, the system bandwidth was initially limited by the LED’s 3 MHz modulation bandwidth. The proposed TIA-TE extends the bandwidth to 8.4 GHz without sacrificing the gain or power dissipation. The subsequent CTLE further extends the bandwidth to 14 MHz. The receiver front end achieves a mid-band transimpedance of 110 dBΩ and an input-referred noise current of 7.2 nA_rms, while dissipating 2.48 mW (excluding the 50 Ω buffer). Simulated 28 Mb/s NRZ eye diagrams demonstrate the feasibility of the proposed TIA-TE architecture for LED-limited VLC links. Full article

Addressing the limitations of conventional inorganic light-emitting diodes (LEDs) in flexible visible light communication (VLC) applications, this study investigates the feasibility of organic light-emitting diodes (OLEDs) as an integrated platform for illumination, display, and communication. The optoelectronic characteristics and modulation bandwidth of red, green, and blue (RGB) OLEDs were systematically measured. Based on the experimental data, a wavelength division multiplexing (WDM) VLC system employing non-return-to-zero on-off keying (NRZ-OOK) modulation was constructed in simulation software for validation. The results indicate stable optoelectronic performance for all three primary-color OLEDs, with a maximum modulation bandwidth of 466 kHz achieved for the blue device. The system simulation demonstrates stable parallel transmission of three independent data channels, attaining a minimum bit error rate (BER) as low as $3.74\times {10}^{-35}$ achieved for the green device. This work confirms the potential of OLEDs for emerging communication applications such as flexible displays and wearable devices. Full article

The nitrogen-vacancy (NV) center magnetic sensor, leveraging nitrogen-vacancy quantum effects, enables high-sensitivity magnetic field detection via optically detected magnetic resonance (ODMR). However, conventional single-point integrated devices suffer from limitations such as inefficient regional magnetic field detection and challenges in discerning the directional variations of dynamic magnetic fields. To address these issues, this study proposes an array- based architecture that innovatively substitutes the conventional 532 nm laser with quantum-dot light-emitting diodes (QLEDs). Capitalizing on the advantages of QLEDs—including compatibility with micro/nano-fabrication processes, wavelength tunability, and high luminance—a 2 × 2 monolithically integrated magnetometer array was developed. Each sensor unit achieves a magnetic sensitivity of below 26 nT·Hz^−1/2 and a measurable range of ±120 μT within the 1–10 Hz effective bandwidth. Experimental validation confirms the array’s ability to simultaneously resolve multi-regional magnetic fields and track dynamic field orientations while maintaining exceptional device uniformity. This advancement establishes a scalable framework for the design of large-scale magnetic sensing arrays, demonstrating significant potential for applications requiring spatially resolved and directionally sensitive magnetometry. Full article

The Internet of Underwater Things (IoUT) has attracted significant attention from researchers due to the fact that seventy percent of the Earth’s surface is covered by water. Reliable underwater communication is the enabler of IoUT. Different carriers, such as electromagnetic waves, sound, and light, are used to transmit data through the water. Among these, optical waves are considered promising due to their high data rates and relatively good bandwidth efficiency, as water becomes transparent to light in the visible spectrum (400–700 nm). However, limitations such as link range, path loss, and turbulence lead to low power and, consequently, a low signal-to-noise ratio (SNR) at the receiver. In this article, we present the design of a smart transceiver for bidirectional communication. The system adapts the divergence angle of the optical beam from the transmitter based on the power of the signal received. This paper details the real-time data transmission process, where the transmitting station consists of a light fidelity (Li-Fi) transmitter with a 470 nm blue-light-emitting diode (LED) and a software-defined radio (SDR) for underwater optical communication. The receiving station is equipped with a Li-Fi receiver, which includes a photodetector with a wide field of view and an SDR. Furthermore, we use pulse position modulation (PPM), which demonstrates promising results for real-time transmission. A key innovation of this paper is the integration of the Li-Fi system with the SDR, while the system adapts dynamically using a servo motor and an Arduino microcontroller assembly. The experimental results show that this approach not only increases throughput but also enhances the robustness and efficiency of the system. Full article

In indoor visible light communication (VLC) and visible light positioning (VLP) systems, the performance of conventional orthogonal frequency-division multiplexing (OFDM) schemes is often compromised due to the nonlinear characteristics and limited modulation bandwidth of light-emitting diodes, the multipath effect in enclosed indoor environments, and the relative positions of transmitters and receivers. This paper proposes an OFDM scheme based on the fractional Fourier transform (FRFT) to address these issues, demonstrating promising results when applied to indoor VLC and VLP systems. The FRFT, a generalization of the conventional Fourier transform (FT) in the fractional domain, captures information in both the time and frequency domains, offering greater flexibility than the FT. In this paper, we first introduce the computation method of the reality-preserving FRFT for an intensity modulation/direct detection VLC system and integrate it with OFDM to optimize system performance. By adopting FRFT-OFDM under the optimal fractional order, we enhance both the bit error ratio (BER) performance and positioning accuracy. Simulation results reveal that the FRFT-OFDM scheme with an optimized fractional order significantly improves the BER and positioning accuracy compared to the FT-OFDM scheme across most receiver positions within the indoor observation plane. For communication, the FRFT-OFDM scheme achieves over 6 dB $E_b/N_0$ gain compared to the FT-OFDM scheme at a BER of $3\times {10}^{-4}$ when the receiver is positioned at most locations in the room. For positioning, the FRFT-OFDM scheme enhances positioning accuracy by more than 1 cm relative to the FT-OFDM scheme at most locations in the room. Notably, both systems maintain the same computational complexity and spectral efficiency. Full article

Visible light communication (VLC) has been viewed as one promising candidate to mitigate the challenging spectrum crisis and radio frequency interference in future 6G mobile communications and networking. Due to the relatively limited baseband modulation bandwidth of VLC light sources—typically, light-emitting diodes—non-orthogonal multiple access (NOMA) techniques have been proposed and explored to enhance the spectral efficiency (SE) of VLC systems. However, almost all reported NOMA VLC schemes focus on well-discussed applications employing a Lambertian light beam configuration and ignore the potential applications with distinct non-Lambertian optical beam configurations. To address this issue, in this work, the performance of non-Lambertian optical beam configuration-based NOMA VLC is comparatively investigated for future 6G mobile networks. The numerical results demonstrate that, for a fundamental two-user application scenario with the far user located at the corner position, a maximum sum rate gain of about 15.6 Mbps could be provided by the investigated distinct non-Lambertian beam-based NOMA VLC, compared with the maximum sum rate of about 93.3 Mbps for the conventional Lambertian configuration with the same power splitting factor. Full article

Simultaneous illumination and communication using solid-state lighting devices like white light-emitting diode (LED) light sources is gaining popularity. The white light LED comprises a single-colored yellow phosphor excited by the blue LED chip. Therefore, color-quality determining parameters like color-rendering index (CRI), correlated color temperature (CCT), and CIE 1931 chromaticity coordinates of generic white LED sources are poor. This article presents the development of multi-color phosphors excited by a blue LED to improve light quality and bandwidth. A multi-layer stacking of phosphor layers excited by a blue LED led to the quenching of photoluminescence (PL) and showed limited bandwidth. To solve this problem, a lens-free, electrically powered, broadband white light source is designed by mounting multi-color phosphor LEDs in a co-planar ring-topology. The CRI, CCT, and CIE 1931 chromaticity coordinates of the designed lamp (DL) were found to be 90, 5114 K, and (0.33, 0.33), respectively, which is a good quality lamp for indoor lighting. CRI of DL was found to be 16% better than that of white LED (WL). Assessment of visible light communications (VLC) feasibility using the DL includes time interval error (TIE) of data pattern or jitter analysis, eye diagram, signal-to-noise ratio (SNR), fast Fourier transform (FFT), and power spectral density (PSD). DL transmits binary data stream faster than WL due to a reduction in rise time and total jitter by 31% and 39%, respectively. The autocorrelation function displayed a narrow temporal pulse for DL. The DL is beneficial for providing high-quality illumination indoors while minimizing PL quenching. Additionally, it is suitable for indoor VLC applications. Full article

Newly introduced Photovoltaic (PV) devices, featuring a built-in chip with an illuminating Light Emitting Diode (LED), have emerged in the commercial market. These devices are touted for their utility as both low- and high-side power switch drivers and for data acquisition coupling. However, comprehensive knowledge and experimentation regarding the limitations of these Photovoltaic Drivers in both switching and signal processing applications remain underexplored. This paper presents a detailed characterization of a Photovoltaic Driver, focusing on its performance under resistive and capacitive loads. Additionally, it delineates the device’s constraints when employed in signal processing. Through the analysis of switching losses across various power switches (Silicon and Silicon Carbide) in both series and parallel driver configurations, this study assesses the driver’s efficacy in operating Junction Field-Effect Transistors (JFETs). Findings suggest that Photovoltaic Drivers offer a low-cost, compact solution for specific applications, such as high-voltage, low-bandwidth measurements, and low-speed turn-on with fast turn-off power switching scenarios, including solid-state switches and hot-swap circuits. Moreover, they present a straightforward, cost-effective method for driving JFETs, simplifying the circuit design and eliminating the need for an additional negative power source. Full article

In medium- and short-range underwater application scenarios, thanks to the superior performance in transmission bandwidth, link latency, and security, underwater wireless optical communication (UWOC) is growing to be a promising complement to the mature underwater acoustic communication technique. In order to extend the future 6G Internet of Things (IOT) to various challenging and valuable underwater scenarios, the underwater spatial coverage and transmission performance has been actively discussed in typical seawater environments. However, almost all current works focus on underwater scenarios including light-emitting diode (LED) transmitters with well-known Lambertian optical beams and fail to characterize the scenarios adopting LED transmitters with distinctive non-Lambertian beam patterns. For addressing this limitation, in this article, the coverage performance of non-Lambertian UWOC for 6G is analyzed and illustrated. Furthermore, the switchable optical beam configuration scheme is proposed and estimated for UWOC. Numerical results illustrate that, compared with about 15.42 dB signal-to-noise ratio (SNR) fluctuation amplitude for UWOC with baseline Lambertian optical beam configuration, the corresponding SNR fluctuation amplitudes of UWOC based with two typical non-Lambertian optical beams are 8.71 dB and 24.60 dB. Furthermore, once the receiver depth is increased to 6.0 m, the SNR fluctuation amplitude for the above three UWOC coverage with distinct beam configuration could be reduced to 5.61 dB, 1.58 dB, and 10.33 dB, respectively. Full article

As a contender in the competitive landscape of next-generation wireless communication technologies, visible light communication (VLC) stands out due to its potential for enhancing transmission rates and spectrum resource utilization. VLC offers various advantages, including license-free operation, high confidentiality, and cost-effectiveness. However, practical implementation faces challenges stemming from the limited modulation bandwidth of light-emitting diodes (LEDs), constraining system capacity and VLC communication rates. To address this limitation, non-orthogonal multiple access (NOMA) emerges as a novel multiple access strategy, particularly suitable for enhancing the capacity and communication rates of downlink VLC systems through power multiplexing. This paper delves into the energy-efficient design of joint LED association and power allocation (LA–PA) for downlink NOMA-based VLC systems. Through an analysis of channel capacity, we transform the non-convex energy-efficient optimization model, accounting for signal non-negativity, per-LED optical power constraints, and user rate constraints, into a convex form. Subsequently, we propose an iterative power allocation algorithm to attain solutions for the optimization problem with pre-established LED associations. Furthermore, we derive a feasibility condition for an LED association, considering signal non-negativity, per-LED optical power constraints, power constraints for successive interference cancellation (SIC), and channel gain between transceiver signals. This condition identifies feasible LEDs capable of maximizing energy efficiency (EE) when combined with the aforementioned power allocation algorithm. Finally, we illustrate the superiority of the joint LA–PA scheme in terms of the EE, transmission reliability, and transmission capacity performance gain over NOMA in the context of VLC. Full article

All-inorganic perovskite nanocrystals (NCs) of CsPbX₃ (X = Cl, Br, I) are promising for displays due to wide color gamut, narrow emission bandwidth, and high photoluminescence quantum yield (PLQY). However, pure red perovskite NCs prepared by mixing halide ions often result in defects and spectral instabilities. We demonstrate a method to prepare stable pure red emission and high-PLQY-mixed-halide perovskite NCs through simultaneous halide-exchange and ligand-exchange. CsPbBr₃ NCs with surface organic ligands are first synthesized using the ligand-assisted reprecipitation (LARP) method, and then ZnI₂ is introduced for anion exchange to transform CsPbBr₃ to CsPbBr_xI_3−x NCs. ZnI₂ not only provides iodine ions but also acts as an inorganic ligand to passivate surface defects and prevent ion migration, suppressing non-radiative losses and halide segregation. The luminescence properties of CsPbBr_xI_3−x NCs depend on the ZnI₂ content. By regulating the ZnI₂ exchange process, red CsPbBr_xI_3−x NCs with organic/inorganic hybrid ligands achieve near-unity PLQY with a stable emission peak at 640 nm. The CsPbBr_xI_3−x NCs can be combined with green CsPbBr₃ NCs to construct white light-emitting diodes with high-color gamut. Our work presents a facile ion exchange strategy for preparing spectrally stable mixed-halide perovskite NCs with high PLQY, approaching the efficiency limit for display or lighting applications. Full article

DC-biased optical orthogonal frequency division multiplexing (DCO-OFDM) has been introduced to visible light networking framework for connected vehicles (LiNEV) systems as a modulation and multiplexing scheme. This is to overcome the light-emitting diode (LED) bandwidth limitation, as well as to reduce the inter-symbol interference caused by the multipath road fading. Due to the implementation of the inverse fast Fourier transform, DC-OFDM suffers from its large peak-to-average power ratio (PAPR), which degrades the performance in LiNEV systems, as the LEDs used in the vehicles’ headlights have a limited optical power-current linear range. To tackle this issue, discrete Fourier transform spread-optical pulse amplitude modulation (DFTS-OPAM) has been proposed as an alternative modulation scheme for LiNEV systems instead of DCO-OFDM. In this paper, we investigate the system performance of both schemes considering the light-emitting diode linear dynamic range and LED 3 dB modulation bandwidth limitations. The simulation results indicate that DCO-OFDM has a 9 dB higher PAPR value compared with DFTS-OPAM. Additionally, it is demonstrated that DCO-OFDM requires an LED with a linear range that is twice the one required by DFTS-OPAM for the same high quadrature amplitude modulation (QAM) order. Furthermore, the findings illustrate that when the signal bandwidth of both schemes significantly exceeds the LED modulation bandwidth, DCO-OFDM outperforms DFTS-OPAM, as it requires a lower signal-to-noise ratio at a high QAM order. Full article

Nowadays, Visible Light Communication (VLC) has gained much attention due to the significant advancements in Light Emitting Diode (LED) technology. However, the bandwidth of LEDs is one of the important concerns that limits the transmission rates in a VLC system. In order to eliminate this limitation, various types of equalization methods are employed. Among these, using digital pre-equalizers can be a good choice because of their simple and reusable structure. Therefore, several digital pre-equalizer methods have been proposed for VLC systems in the literature. Yet, there is no study in the literature that examines the implementation of digital pre-equalizers in a realistic VLC system based on the IEEE 802.15.13 standard. Hence, the purpose of this study is to propose digital pre-equalizers for VLC systems based on the IEEE 802.15.13 standard. For this purpose, firstly, a realistic channel model is built by collecting the signal recordings from a real 802.15.13-compliant VLC system. Then, the channel model is integrated into a VLC system modeled in MATLAB. This is followed by the design of two different digital pre-equalizers. Next, simulations are conducted to evaluate their feasibility in terms of the system’s BER performance under bandwidth-efficient modulation schemes, such as 64-QAM and 256-QAM. Results show that, although the second pre-equalizer provides lower BERs, its design and implementation might be costly. Nevertheless, the first design can be selected as a low-cost alternative to be used in the VLC system. Full article

Over the past decade, perovskite technology has been increasingly applied in solar cells, nanocrystals, and light-emitting diodes (LEDs). Perovskite nanocrystals (PNCs) have attracted significant interest in the field of optoelectronics owing to their exceptional optoelectronic properties. Compared with other common nanocrystal materials, perovskite nanomaterials have many advantages, such as high absorption coefficients and tunable bandgaps. Owing to their rapid development in efficiency and huge potential, perovskite materials are considered the future of photovoltaics. Among different types of PNCs, CsPbBr₃ perovskites exhibit several advantages. CsPbBr₃ nanocrystals offer a combination of enhanced stability, high photoluminescence quantum yield, narrow emission bandwidth, tunable bandgap, and ease of synthesis, which distinguish them from other PNCs, and make them suitable for various applications in optoelectronics and photonics. However, PNCs also have some shortcomings: they are highly susceptible to degradation caused by environmental factors, such as moisture, oxygen, and light, which limits their long-term performance and hinders their practical applications. Recently, researchers have focused on improving the stability of PNCs, starting with the synthesis of nanocrystals and optimizing (i) the external encapsulation of crystals, (ii) ligands used for the separation and purification of nanocrystals, and (iii) initial synthesis methods or material doping. In this review, we discuss in detail the factors leading to instability in PNCs, introduce stability enhancement methods for mainly inorganic PNCs mentioned above, and provide a summary of these approaches. Full article

Visible Light Communication (VLC) represents an emerging technology where a short-range data connection is obtained by modulating the energy radiated by Light Emitting Diodes (LEDs) at frequencies from a few kHz up to hundreds of MHz. The bandwidth/distance performance of such links is a compromise related to the available Signal-to-Noise ratio (SNR). At present, VLC links with bandwidth beyond the Gb/s and distance limited to a few cm or distances up to 100 m but data rates of a few kb/s have been demonstrated. Chirp coding with pulse compression is a well-known technique capable of recovering useful data from low SNR signals, widely employed, for example, in radar. In spite of the possible advantages, its application in VLC has never been investigated. Unfortunately, the pulse compressor is quite calculation-intensive, and only devices like Field-Programmable-Gate-Arrays (FPGAs) can support a low-latency real-time implementation. In this paper we demonstrate a real-time VLC link based on chirp coding and pulse compression coded in FPGA. For example, a chirp with bandwidth and length of 1.7 MHz and 17.92 µs, respectively, is demonstrated to support a link at 1.56 Mb/s over 2.8 m distance and a latency below 40 µs. Moreover, the communication-distance increase achievable by chirps of increasing temporal length is demonstrated and compared to the theoretical background. Full article