Search Results (778)

Implantable technologies targeting the cerebral cortex and deeper brain structures are increasingly utilised in human–machine interfacing, advanced neuroprosthetics, and clinical interventions for neurological conditions. These systems require highly efficient and low-power methods for exchanging information between the implant and external electronics. Traditional approaches often rely on inductively coupled data transfer (ic-DT), where the same coils used for wireless power are modulated for communication. Other designs use high-frequency antenna-based radio systems, typically operating in the 401–406 MHz MedRadio band or the 2.4 GHz ISM band. A promising alternative is intrabody communication (IBC), which leverages the bioelectrical characteristics of body tissue to enable signal propagation. This work presents a theoretical investigation into two schemes—inductive coupling and galvanically coupled IBC (gc-IBC)—as applied to cortical data links, considering frequencies from 1 to 10 MHz and implant depths of up to 7 cm. We propose a hybrid solution where gc-IBC supports data transmission and inductive coupling facilitates wireless power delivery. Our findings indicate that gc-IBC can accommodate wider bandwidths than ic-DT and offers significantly reduced path loss, approximately 20 dB lower than those of conventional RF-based antenna systems. Full article

This paper provides a comprehensive review of recent advancements in radio-frequency (RF) multifunctional components with integrated filtering characteristics, including tunable filtering attenuators, filtering power dividers, filtering couplers, and filtering Butler matrices, all of which play critical roles in wireless communication systems. With the increasing demand for miniaturization, integration, and low-loss performance in RF front-ends, multifunctional components with filtering characteristics have become essential. This review first introduces tunable attenuators and filtering attenuators based on various technologies such as PIN diodes, graphene-based structures, and RF-MEMS switches, and also analyzes their advantages, limitations, and performance. Then, we discuss filtering power dividers developed from Wilkinson structures, three-line coupled structures, resonator-based coupling matrix methods, and SSPP-waveguide hybrids. Furthermore, filtering couplers and filtering Butler matrices are reviewed, highlighting their capability to simultaneously achieve amplitude and phase control, making them suitable for multi-beam antenna feeding networks. Finally, a brief conclusion is summarized. Future research directions, such as hybrid technologies, novel materials, broadband and multi-band designs, and antenna-matrix co-design, are suggested to further enhance the performance and practicality of multifunctional RF components for next-generation wireless communication systems. Full article

With the continuous increase in power capacity of spacecraft radio frequency payloads, low-pressure discharge effects have become a significant factor threatening the safe operation of spacecraft payloads. Clarifying the low-pressure discharge effects and their plasma evolution mechanisms is of great importance for elucidating the underlying discharge processes and proposing effective preventive measures. Based on the characteristics of the actual operating environment of spacecraft microwave payloads, this paper proposes a global simulation model for low-pressure discharge plasma in humid air. The validity of the model was verified through online diagnostic experiments on low-pressure discharge plasma. Using the constructed global plasma model, the influence of key parameters such as pressure and humidity on electron and ion densities in the plasma was investigated, revealing the impact mechanisms of initial discharge conditions on plasma characteristics. The potential hazards of these factors to spacecraft microwave payloads were also discussed. This model provides a foundation for improving the accurate prediction of key parameters in low-pressure discharge. Full article

Bud break is a critical phenological stage in muscadine grapevines, marking the start of the growing season and the increasing need for irrigation management. Real-time bud detection enables irrigation to match muscadine grape phenology, conserving water and enhancing performance. This study presents BudCAM, a low-cost, solar-powered, edge computing camera system based on Raspberry Pi 5 and integrated with a LoRa radio board, developed for real-time bud detection. Nine BudCAMs were deployed at Florida A&M University Center for Viticulture and Small Fruit Research from mid-February to mid-March, 2024, monitoring three wine cultivars (A27, noble, and Floriana) with three replicates each. Muscadine grape canopy images were captured every 20 min between 7:00 and 19:00, generating 2656 high-resolution (4656 × 3456 pixels) bud break images as a database for bud detection algorithm development. The dataset was divided into 70% training, 15% validation, and 15% test. YOLOv11 models were trained using two primary strategies: a direct single-stage detector on tiled raw images and a refined two-stage pipeline that first identifies the grapevine cordon. Extensive evaluation of multiple model configurations identified the top performers for both the single-stage (mAP@0.5 = 86.0%) and two-stage (mAP@0.5 = 85.0%) approaches. Further analysis revealed that preserving image scale via tiling was superior to alternative inference strategies like resizing or slicing. Field evaluations conducted during the 2025 growing season demonstrated the system’s effectiveness, with the two-stage model exhibiting superior robustness against environmental interference, particularly lens fogging. A time-series filter smooths the raw daily counts to reveal clear phenological trends for visualization. In its final deployment, the autonomous BudCAM system captures an image, performs on-device inference, and transmits the bud count in under three minutes, demonstrating a complete, field-ready solution for precision vineyard management. Full article

The widespread integration of low-power electronic devices in IoT, biomedical, and sensing applications has intensified the demand for energy-autonomous solutions. Radio Frequency Energy Harvesting (RFEH) offers a promising alternative by leveraging ambient RF signals available in both indoor and outdoor environments. Despite its conceptual appeal, practical deployment still faces major challenges. This systematic literature review (SLR) examines 25 recent studies, following the PRISMA methodology, to provide a comprehensive overview of current RFEH architectures. It focuses on three critical components: receiving antennas, impedance matching circuits (IMCs), and RF-to-DC rectifiers. Design strategies are reviewed and compared across antenna types, matching techniques, and rectifier configurations. The review also highlights persistent challenges and outlines directions for the development of compact, efficient, and robust energy-harvesting systems for next-generation wireless technologies. Full article

This work presents an Internet of Things (IoT) node designed for low-power agrifood chain tracking in remote areas, where long-range terrestrial communication is either unavailable or severely limited. The novelty of this study lies in the development and characterization of an IoT node prototype that leverages direct-to-satellite connectivity through a geostationary Earth orbit (GEO) satellite, using long-range frequency-hopping spread spectrum (LR-FHSS) modulation in the licensed S-band. The prototype integrates a microcontroller unit that manages both the radio modem and a suite of sensors, enclosed in a plastic box suitable for field deployment. Characterization in an anechoic chamber demonstrated a maximum effective isotropic radiated power (EIRP) of $27.5$ dBm, sufficient to establish a reliable satellite link. The onboard sensors provide global positioning as well as measurements of acceleration, temperature, humidity, and solar radiation intensity. Prototype performance was assessed in two representative scenarios: stationary and mobile. Regarding energy consumption, the average charge drained by the radio modem per transmission cycle was measured to be 356 mC. With a battery pack composed of four 2500 mAh NiMH cells, the estimated upper bound on the number of transmitted packets is approximately 25,000. Full article

Children with intoeing gait are at increased risk of tripping and consequent injury, reduced mobility, and psychological issues. Quantification of tripping is needed outside the gait lab during daily life for improved clinical assessment and treatment evaluation and to enrich the database for artificial intelligence (AI) learning. This paper presents the development of a low-cost, wearable tripping monitor to log a child’s Tripping Hazard Events (THEs) and steps taken during two weeks of everyday activity. A combination of sensors results in a high probability of THE detection, even during rapid gait, while guarding against false positives and minimizing power and therefore monitor size. A THE is logged when the feet come closer than a predefined threshold during the intoeing foot swing phase. Foot proximity is determined by a Radio Frequency Identification (RFID) reader in “sniffer” mode on the intoeing foot and a target of passive Near-Field Communication (NFC) tags on the contralateral foot. A Force Sensitive Resistor (FSR) in the intoeing shoe sets a time window for sniffing during gait and enables step counting. Data are stored in 15 min epochs. Laboratory testing and an IRB-approved human participant study validated system performance and identified the need for improved mechanical robustness, prompting a redesign of the monitor. A custom Python (version 3.10.13)-based Graphical User Interface (GUI) lets clinicians initiate recording sessions and view time records of THEs and steps. The monitor’s flexible design supports broader applications to real-world activity detection. Full article

Reactive jamming remains a critical threat to low-latency telemetry of Unmanned Aerial Vehicles (UAVs) using Orthogonal Frequency Division Multiplexing (OFDM). In this paper, a Bi-scale Mahalanobis approach is proposed to detect and classify reactive jamming attacks on UAVs; it jointly exploits window-level energy and the Sevcik fractal dimension and employs self-adapting thresholds to detect any drift in additive white Gaussian noise (AWGN), fading effects, or Radio Frequency (RF) gain. The simulations were conducted on 5000 frames of OFDM signals, which were distorted by Rayleigh fading, a ±10 kHz frequency drift, and log-normal power shadowing. The simulation results achieved a precision of 99.4%, a recall of 100%, an F1 score of 99.7%, an area under the receiver operating characteristic curve (AUC) of 0.9997, and a mean alarm latency of 80 μs. The method used reinforces jam resilience in low-power commercial UAVs, yet it needs no extra RF hardware and avoids heavy deep learning computation. Full article

The article proposes a novel modulation scheme with a low peak-to-average ratio (PAPR), referred to as offset rotation interpolation modulation (ORIM), which is particularly suitable for low-power consumption and enhanced coverage scenarios in the sixth generation (6G) of wireless communication. ORIM comprises three modulation schemes: I-QPSK, I-BPSK, and I-π/2 BPSK. They are derived from cyclic offsetting, phase rotation, and interpolation, and applied to QPSK, BPSK, and π/2 BPSK, respectively. Simulation results in discrete Fourier transform-spread-orthogonal frequency division multiplexing (DFT-s-OFDM) systems demonstrate that ORIM achieves a lower peak-to-average power ratio (PAPR) than the π/2-BPSK scheme specified in the 5G New Radio (NR) protocol, without incurring any performance degradation in terms of block error rate (BLER). Moreover, with the addition of frequency domain spectrum shaping (FDSS), I-π/2 BPSK demonstrates superior performance over π/2-BPSK in both PAPR and BLER metrics under the TDL-A channel conditions. In addition, the complexity of modulation at the transmitting end or demodulation at the receiving end of ORIM is of the same order of magnitude as that of π/2 BPSK, thereby achieving a certain level of overall performance improvement. Full article

This paper presents an advanced radio frequency (RF)–direct current (DC) power conversion architecture based on a multistage Cockcroft–Walton topology. The proposed design achieves an enhanced voltage conversion ratio while maintaining superior RF-DC conversion efficiency under low input power conditions. To address the inherent limitations of cascading Cockcroft–Walton topologies with class-F load networks, a novel ground plane isolation technique was developed, which utilizes the reverse-side metallization of the circuit board. A 5.8 GHz two-stage Cockcroft–Walton voltage multiplier rectifier was fabricated and characterized. Measurement results demonstrate that the circuit achieves a maximum output voltage of 7.4 V and a peak conversion efficiency of 70.5% with an input power of only 30 mW, while maintaining stable performance across varying load conditions. A comparison with a two-stage Dickson rectifier reveals that the Cockcroft–Walton rectifier exhibits superior output voltage and conversion efficiency. The proposed architecture delivers significant improvements in power conversion efficiency and voltage multiplication capability compared to conventional designs, establishing a new benchmark for low-power wireless energy harvesting applications. Full article

Particle accelerators are powerful tools in fundamental research, medicine, and industry that provide high-energy beams that can be used to study matter and to enable advanced applications. The state-of-the-art particle accelerators are fundamentally constructed from superconducting radio-frequency (SRF) cavities, which act as resonant structures for the acceleration of charged particles. The performance of such cavities is governed by inherent superconducting material properties such as the transition temperature, critical fields, penetration depth, and other related parameters and material quality. For the last few decades, bulk niobium has been the preferred material for SRF cavities, enabling accelerating gradients on the order of ~50 MV/m; however, its intrinsic limitations, high cost, and complicated manufacturing have motivated the search for alternative strategies. Among these, sputter-deposited superconducting thin films offer a promising route to address these challenges by reducing costs, improving thermal stability, and providing access to numerous high-T_c superconductors. This review focuses on progress in sputtered superconducting materials for SRF applications, in particular Nb, NbN, NbTiN, Nb₃Sn, Nb₃Al, V₃Si, Mo–Re, and MgB₂. We review how deposition process parameters such as deposition pressure, substrate temperature, substrate bias, duty cycle, and reactive gas flow influence film microstructure, stoichiometry, and superconducting properties, and link these to RF performance. High-energy deposition techniques, such as HiPIMS, have enabled the deposition of dense Nb and nitride films with high transition temperatures and low surface resistance. In contrast, sputtering of Nb₃Sn offers tunable stoichiometry when compared to vapour diffusion. Relatively new material systems, such as Nb₃Al, V₃Si, Mo-Re, and MgB₂, are just a few of the possibilities offered, but challenges with impurity control, interface engineering, and cavity-scale uniformity will remain. We believe that future progress will depend upon energetic sputtering, multilayer architectures, and systematic demonstrations at the cavity scale. Full article

As a core functional device in microwave systems, attenuators play a crucial role in key aspects such as signal power regulation, amplitude attenuation, and impedance matching. Addressing the pressing technical issues currently exposed by attenuators in practical applications, such as excessive insertion loss, low attenuation accuracy, large physical dimensions, and insufficient process reliability, this paper proposes a design scheme for an RF three-bit reconfigurable stepped attenuator based on radio frequency micro-electromechanical systems (RF MEMS) switches. The attenuator employs planar integration of the T-type attenuation network, Coplanar Waveguide (CPW), Y-shaped power divider, and RF MEMS switches. While ensuring rational power distribution and stable attenuation performance over the full bandwidth, it reduces the number of switches to suppress parasitic parameters, thereby enhancing process feasibility. Test results confirm that this device demonstrates significant advancements in attenuation accuracy, achieving a precision of 1.18 dB across the 0–25 dB operational range from DC to 20 GHz, with insertion loss kept below 1.65 dB and return loss exceeding 12.15 dB. Additionally, the device boasts a compact size of merely 0.66 mm × 1.38 mm × 0.32 mm, significantly smaller than analogous products documented in existing literature. Meanwhile, its service life approaches 5 × 10⁷ cycles. Together, these two attributes validate the device’s performance reliability and miniaturization advantages. Full article

Wireless sensor networks (WSNs) are an advanced solution for data collection in Internet of Things (IoT) applications and remote and harsh environments. These networks rely on a collection of distributed sensors equipped with wireless communication capabilities to collect low-cost and small-scale data. WSNs face numerous challenges, including network congestion, slow speeds, high energy consumption, and a short network lifetime due to their need for a constant and stable power supply. Therefore, improving the energy efficiency of sensor nodes through solar energy harvesting (SEH) would be the best option for charging batteries to avoid excessive energy consumption and battery replacement. In this context, modern wireless communication technologies, such as Wi-Fi and Li-Fi, emerge as promising solutions. Wi-Fi provides internet connectivity via radio frequencies (RF), making it suitable for use in open environments. Li-Fi, on the other hand, relies on data transmission via light, offering higher speeds and better energy efficiency, making it ideal for indoor applications requiring fast and reliable data transmission. This paper aims to integrate Wi-Fi and Li-Fi technologies into the SEH-WSN architecture to improve performance and efficiency when used in all applications. To achieve reliable, efficient, and high-speed bidirectional communication for multiple devices, the paper utilizes a Markov model, sleep scheduling, and smart switching algorithms to reduce power consumption, increase signal-to-noise ratio (SNR) and throughput, and reduce bit error rate (BER) and latency by controlling the technology and power supply used appropriately for the mode, sleep, and active states of nodes. Full article

The rapid growth of the Internet of Things (IoT) has driven the need for ultra-low-power wireless communication systems. Wake-up receivers (WuRXs) have emerged as a key technology to enable energy-efficient, near-always-on operation for IoT devices. This review explores the state of the art in WuRXs design, focusing on low-power architectures, key trade-offs, and recent advancements. We discuss the challenges in achieving low power consumption while maintaining sensitivity, power consumption, and interference resilience. The review highlights the evolution from radio frequency (RF) envelope detection architectures to more complex heterodyne and subthreshold designs and concludes with future directions for WuRXs research. Full article

With the booming development of the 5G market in recent years, super-high frequency (SHF) resonators will play an increasingly critical role in 5G and future communication systems. Facing the growing market demand for miniaturized, high-bandwidth, and low insertion loss filters, the design of SHF resonators and filters with a high effective electromechanical coupling coefficient (K²_eff) and quality factor, low insertion loss, high passband flatness, strong out-of-band rejection, and high power handling capacity has placed high demands on piezoelectric material preparation, process optimization, and resonator design. The polarity-inverted Al(Sc)N multilayer substrate has become one of the key solutions for SHF resonators. This review provides a comprehensive overview of the recent advances in SHF Al(Sc)N bulk acoustic wave (BAW) resonators. It systematically discusses the device design methodologies, structural configurations, and material synthesis techniques for high-quality Al(Sc)N thin films. Particular emphasis is placed on the underlying mechanisms and engineering strategies for polarity control in Al(Sc)N-based periodically poled multilayer structures. The progress in periodically poled piezoelectric film (P3F) BAW resonators is also examined, with special attention to their ability to significantly boost the operating frequency of BAW devices without reducing the thickness of the piezoelectric layer, while maintaining a high K²_eff. Finally, the review outlines current challenges and future directions for achieving a higher quality factor (Q), improved frequency scalability, and greater integration compatibility in SHF acoustic devices, paving the way for next-generation radio frequency (RF) front-end technologies in 5G/6G and beyond. Full article