Search Results (192)

To address the issue of restricted grout diffusion caused by seepage effects during grouting in sandy soil layers, this study proposes an optimised grouting method for water-based polyurethane-cement composite grout (WPU-CS) under vacuum-pressure synergy. By establishing a porous medium flow model based on the mass conservation equation and linear filtration law, the influence mechanism of cement particle seepage effects was quantitatively characterised. An orthogonal test (L₉(3⁴)) optimised the grout composition, determining the optimal parameter combination as the following: water-to-cement ratio 1.5:1, polyurethane-to-cement ratio 5~10%, magnesium aluminium silicate content 1%, and hydroxypropyl methylcellulose content 0.15%. Vacuum permeation grouting tests demonstrated that compared to pure cement slurry, WPU-CS reduced filter cake thickness by 80%, significantly suppressing the leaching effect (the volume fraction $\delta$ of cement particles exhibited exponential decay with increasing distance $r$ from the grouting end, and the slurry front velocity gradually decreased). Concurrently, the porosity $\varphi$ in the grouted zone showed a gradient distribution (with more pronounced porosity reduction near the grouting end). When vacuum pressure increased from −10 kPa to −30 kPa, slurry diffusion distance rose from 11 cm to 18 cm (63.6% increase). When grouting pressure increased from 20 kPa to 60 kPa, diffusion distance increased from 8 cm to 20 cm (150% increase). The study confirms that synergistic control using WPU-CS with moderate grouting pressure and high vacuum effectively balances seepage suppression and soil stability, providing an innovative solution for efficient sandy soil reinforcement. Full article

Nanocellulose–graphene derivative (NC–GD) composite membranes have attracted increasing attention as sustainable separation materials with high specific surface area, mechanical strength, and controllable interfacial chemistry. This review contextualizes the development of NC–GD composite membranes within advanced membrane technologies and summarizes recent progress in their structural design, interfacial mechanisms, and water purification applications. The synthesis and assembly of nanocellulose and graphene derivatives are analyzed, focusing on how surface functionalization regulates interfacial compatibility and transport pathways. Comparative evaluation of fabrication approaches—including vacuum filtration, layer-by-layer assembly, and solution casting—highlights their influence on structural uniformity and permeability. Key findings indicate that hydrogen bonding, electrostatic coupling, and π–π interactions govern the layer stability of composite membranes and the synergistic formation of nanochannels (by NC and GDs), thereby enabling efficient water permeation, selective separation, and fouling resistance. Overall, NC–GD membranes exhibit outstanding performance in heavy metal adsorption, dye removal, oil–water separation, and antibacterial treatment, representing a promising platform for next-generation sustainable water purification systems. Full article

Hybrid buckypapers (BPs) composed of graphene nanoplatelets (GNPs) and carbon nanotubes (CNTs) hold great potential for applications in flexible electronics, electromagnetic shielding, and energy storage. In this study, hybrid BPs were fabricated and characterized to evaluate their structural, thermal, and electrical properties. Hybrid BPs with varying GNP/CNT mass ratios (0/100, 25/75, 50/50, 75/25, 85/15, 90/10, and 95/5 wt%) were prepared via vacuum-assisted filtration of well-dispersed aqueous suspensions stabilized by surfactants. The resulting hybrid GNP/CNT BPs were dried and subjected to post-treatment processes to enhance structural integrity and electrical performance. Characterization techniques included scanning electron microscopy (SEM), X-ray diffraction (XRD), Fourier transform infrared (FT-IR), Raman spectroscopy, thermogravimetric analysis (TGA), nitrogen adsorption/desorption isotherms, and impedance spectroscopy (IS). The hybrid GNP/CNT BPs exhibited electrical conductivities comparable to conventional CNT-based BPs. At GNP concentrations of 25 to 50 wt%, electrical conductivity values approached those of CNT-based BPs, while at GNP concentrations between 75 and 90 wt%, a slight increase in conductivity was observed (171%). These results highlight a synergistic effect at lower CNT concentrations, where the combination of CNTs and GNPs enhances conductivity. The findings suggest that optimal conductivity is achieved through a balanced incorporation of both materials, offering promising prospects for advanced BP applications. Full article

The global freshwater scarcity crisis demands sustainable solutions aligned with circular economy principles. Solar-driven steam generation (SSG) has emerged as a promising approach to obtain freshwater from seawater or wastewater using solar energy. However, its widespread application relies on the development of energy-efficient, eco-friendly, and high-performance photothermal conversion materials. Herein, we present a sustainable strategy for converting autumn-fallen plane tree leaves into a photothermal material (AC-800) via KOH activation at 800 °C. AC-800 exhibits 91% broadband absorption (250–2500 nm). A light-absorbing layer fabricated by vacuum filtration was used for SSG tests. Under 1 sun irradiation, AC-800 achieves an evaporation rate of 1.5441 kg·m⁻²·h⁻¹ with 87.1% solar-to-vapor efficiency and a surface temperature of 48.3 °C. Ten repetitive cycles of experiments using AC-800 has demonstrated the cycling stability of SSG. Desalinated water meets World Health Organization (WHO) drinking water standards, and organic dye removal from wastewater in distilled water reaches ~100%. This low-cost, eco-friendly strategy advances sustainable SSG, with potential in seawater desalination and wastewater treatment to support circular economy objectives. Full article

To improve the efficiency of aquatic environmental monitoring, an in-situ solid-phase extraction (SPE) system using amphibious (waterproof) drones was developed and validated using recovery testing with samples containing known concentrations of systemic insecticides in the laboratory and using real samples from natural water bodies. The system used a water-resistant linear actuator for continuous aspiration at 1–10 mL min⁻¹ through a pre-washed hydrophilic–lipophilic balanced SPE cartridge. The system functioned properly during field sampling using vacuum-mode filtration to avoid overpressure, overcurrent, and contamination through repeated filtration. The recovery tests using 10 ng L⁻¹ of each target analyte in ultra-pure water samples produced satisfactory recovery results of 89–96% (relative standard deviation < 10%). In the real sampling of water bodies, the developed system was able to detect target analytes of 0.9–180 ng L⁻¹. The results are comparable to those obtained using in-situ manual SPE from boat sampling, irrespective of differences in the two aspiration systems. These findings suggest that the application of the developed drone-assisted in situ SPE system can improve the efficiency of real-sample monitoring of natural water bodies. Full article

Covalent organic framework (COF) membranes are eminent candidates in filtration and separation applications due to their high porosity, ordered pore size, versatile molecular structure, inherent mechanical properties, and excellent stability. However, large-scale COF membranes suffer from several issues, including stacking and crystal defects, which negatively impact their rejection performance. In this study, a continuous thin film of porphyrinic-based COF (i.e., COF-TCPP (Fe)) with various thicknesses was fabricated on a PVDF support layer via a vacuum-assisted interfacial polymerization method. The composite membranes were then characterized, and their filtration and dye/salt separation performance were evaluated using a dead-end filtration cell. The results showed that the rejection efficiencies of Congo red and acid fuchsin for the optimal proposed membrane were 99.5% and 95.8%, respectively. In comparison, the corresponding values for the pristine membrane were 73.3% and 62.8%. The results also showed that with an increase in the COF loading concentration during synthesis, the membrane flux decreased, while the rejection efficiency increased. This study proposes a simple and effective method to mitigate the large-scale issues of COF-based membranes and to enhance the separation performance of existing polymeric membranes. Full article

Currently, electrochemical devices and portable electronic equipment play a significant role in people’s daily lives. Zinc-ion batteries (ZIBs) are growing rapidly due to their excellent safety, eco-friendliness, abundance of resources, and cost-effectiveness. The application of biomass as a polymer separator is gradually expanding in order to promote a circular economy and sustainable materials. This research focuses on the usage of cellulose fibers obtained from coffee parchment (CP) waste. The extracted cellulose fibers are produced via both mechanical and chemical methods. The sustainable separators are fabricated through vacuum filtration using a polymer filter membrane. The impact of incorporating silica particles and varying silica content on the physical and electrochemical properties of a cellulose-based separator is examined. The optimum amount of silica integrated into the cellulose separator is determined to be 5 wt%. This content led to an effective distribution of the silica particles, enhanced wettability, and improved fire resistance. The ZIBs incorporating cellulose/recycled silica at 5 wt% demonstrate exceptional cycle stability and the highest capacity retention (190% after 400 cycles). This study emphasizes the promise of sustainable polymers as a clean energy resource, owing to their adaptability and simplicity of processing, serving as a substitute for synthetic polymers sourced from fossil fuels. Full article

The development of miniaturized sensors has become relevant for the detection of chemical/biological substances, since they use and detect low concentrations, such as flocculants based on amines for the mining industry. In this study, buckypaper (BP) films based on carboxylic acid functionalized multi-walled carbon nanotubes (f-MWCNTs) were produced through vacuum filtration on cellulose filter paper to carry out sensory function in samples containing ether-amine (volumes: 1%, 5%, 10% and 100%). The morphological characterization of the BPs by scanning electron microscopy showed f-MWCNT aggregates randomly distributed on the cellulose fibers. Vibrational analysis by Raman spectroscopy indicated bands and sub-bands referring to f-MWCNTs and vibrational modes corresponding to chemical bonds present in the ether-amine (EA). The electrical responses of the BP to the variation in analyte concentration showed that the sensor differentiates deionized water from ether-amine, as well as the various concentrations present in the different analytes, exhibiting response time of 3.62 ± 0.99 min for the analyte containing 5 vol.% EA and recovery time of 21.16 ± 2.35 min for the analyte containing 10 vol.% EA, revealing its potential as a real-time response chemiresistive sensor. Full article

Developing advanced antimicrobial agents is critically imperative to address antibiotic-resistant infection crises. MXenes have emerged as a potential nanomedicine for antibacterial applications, but they suffer from suboptimal photothermal conversion efficiency and inherent cytotoxicity. Herein, we report the synthesis of MXene (Ti₃C₂)-based nanohybrids and hybrid membranes through firstly interfacial conjugation of self-assembled β-lactoglobulin nanofibers (β-LGNFs)-inspired copper sulfide nanoparticles (CuS NPs) onto MXene nanosheets, and subsequent vacuum filtration of the created β-LGNF-CuS/MXene nanohybrids. The constructed β-LGNF-CuS/MXene nanohybrids exhibit excellent photothermal conversion performances and satisfactory biocompatibility and minimal cytotoxicity toward mammalian cells, ascribing to the introduction of highly biocompatible β-LGNFs into the hybrid system. In addition, the fabricated β-LGNF-CuS/MXene hybrid membranes demonstrate high efficiency in antibacterial application through the synergistic photothermal and material-related antibacterial effects of both MXene and CuS NPs. Therefore, the ideas and findings shown in this study are useful for inspiring researchers to design and fabricate functional and biocompatible 2D material-based hybrid membranes for antimicrobial applications. Full article

Resource reutilization of industrial waste mud has encountered challenges due to its high water content, enhanced fluidity, and inherent difficulty in segregating mud and water phases. The author first screened out efficient flocculants through flocculation dehydration tests and then adopted the technology of vacuum filtration combined with electroosmosis dehydration to conduct deep dehydration of waste mud. Among them, the independently designed vacuum filtration electroosmosis system effectively solves the problems of easy clogging and bending of the traditional system. On this basis, geopolymer fluid solidified soil was prepared using dehydrated mud, furnace slag, and fly ash as raw materials, and the influencing factors of its long-term service performance were studied. It was confirmed that the efficient treatment capacity of the combined dehydration technology for industrial waste mud, and the geopolymer fluid solidified soil prepared from dehydrated mud has engineering application potential. This research provides a reference for the resource utilization of industrial waste mud. Full article

The intrinsic trade-off among sensitivity, response speed, and measurement range continues to hinder the wider adoption of flexible pressure sensors in areas such as medical diagnostics and gesture recognition. In this work, we propose a grid-structured polycaprolactone/thermoplastic-polyurethane nanofiber pressure sensor decorated with multi-walled carbon nanotubes (PCL/TPU@MWCNTs). By introducing a gradient grid membrane, the strain distribution and reconstruction of the conductive network can be modulated, thereby alleviating the conflict between sensitivity, response speed, and operating range. First, static mechanical simulations were performed to compare the mechanical responses of planar and grid membranes, confirming that the grid architecture offers superior sensitivity. Next, PCL/TPU@MWCNT nanofiber membranes were fabricated via coaxial electrospinning followed by vacuum-filtration and assembled into three-layer planar and grid piezoresistive pressure sensors. Their sensing characteristics were evaluated by simple index-finger motions and slide the mouse wheel identified. Within 0–34 kPa, the sensitivities of the planar and grid sensors reached 1.80 kPa⁻¹ and 2.24 kPa⁻¹, respectively; in the 35–75 kPa range, they were 1.03 kPa⁻¹ and 1.27 kPa⁻¹. The rise/decay times of the output signals were 10.53 ms/11.20 ms for the planar sensor and 9.17 ms/9.65 ms for the grid sensor. Both sensors successfully distinguished active index-finger bending at 0–0.5 Hz. The dynamic range of the grid sensor during the extension motion of the index finger is 105 dB and, during the scrolling mouse motion, is 55 dB, affording higher measurement stability and a broader operating window, fully meeting the requirements for high-precision hand-motion recognition. Full article

Heavy metal pollution in landfill soil poses a dual challenge of environmental toxicity and resource depletion. Enzyme-induced carbonate precipitation (EICP) was systematically evaluated as a sustainable stabilization method for cadmium (Cd), lead (Pb), and chromium (Cr) under both solution- and soil-phase conditions. Laboratory-scale experiments demonstrated that EICP achieved over 80% removal efficiency for Cd, Pb, and copper (Cu) in solution-phase systems, while soil-phase trials focused on Cd, Pb, and Cr to simulate realistic field conditions. Optimal performance was achieved using a 1:1 molar ratio of soybean-derived urease (1.0 U/mL) to CaCl₂ (0.5 M), with Cd stabilization reaching 91.5%. Vacuum-assisted filtration improved treatment uniformity by 29.2% in clay soils. X-ray diffraction identified crystalline otavite in Cd systems, while Pb and Cu were stabilized via surface adsorption. Sequential extraction confirmed that over 70% of Cd was transformed into carbonate-bound phases. Treated soils met TCLP leaching standards and reuse criteria, maintaining neutral pH (7.2–8.1) and low salinity. Compared to cement-based methods, EICP avoids CO₂ release from calcination and fossil fuel use. Carbon in urea is retained as solid CaCO₃, reducing emissions by 0.3–0.5 t CO₂-eq per ton of soil. These findings support EICP as a scalable, low-carbon alternative for landfill soil remediation. Full article

Adsorption is one of the simplest and most cost-effective techniques for water decontamination. In this field, biochar has recently emerged as a promising alternative to traditional adsorbents, exhibiting a high surface area and affinity to metal ions, as well as often being waste-derived. Similarly, reduced graphene oxide (rGO) shows an excellent adsorption capacity. Having self-assembling properties, it has already been employed to obtain self-standing heavy-metal-adsorbing membranes. In this research, a novel self-standing membrane of biochar and rGO is presented. It was obtained through an eco-friendly method, consisting of the simple mechanical mixing of the two components, followed by vacuum filtration and mild drying. Vine pruning biochar (VBC) was employed in different rGO/biochar mass ratios, ranging from 1/1 to 1/9. The best compromise between membrane integrity and biochar content was achieved with a 4/6 proportion. This sample was also replicated using chestnut-shell-derived biochar. The composite rGO–biochar membranes were characterized through XRD, FTIR-ATR, TG-DTG, SEM-EDX, BET, ZP, particle dimension, and EPR analyses. Then, they were tested for metal ion adsorption with 10 mM Cu²⁺ and 100 mM Zn²⁺ aqueous solutions. The adsorption capacity of copper and zinc was found to be in the range of 1.51–4.03 mmol_Cu g⁻¹ and 18.16–21.99 mmol_Zn g⁻¹, respectively, at an acidic pH, room temperature, and contact time of 10 min. Interestingly, the composite rGO–biochar membranes exhibited a capture behavior between that of pure rGO and VBC. Full article

Ti-based MXenes such as Ti₃C₂T_X and Ti₂CT_X have attracted considerable attention because of their superior electromagnetic interference (EMI) shielding effectiveness compared to other EMI shielding materials, especially for high electromagnetic (EM) wave absorption. In this study, we investigated the microstructural changes produced by heat treatment and their effect on the EMI shielding properties of Ti-based MXenes. Ti₃C₂T_X and Ti₂CT_X films were prepared using vacuum filtration and annealed at temperatures up to 300 °C. The microstructures and chemical bonding properties of these heat-treated Ti₃C₂T_X and Ti₂CT_X films were analyzed, and the EMI shielding effectiveness was measured in the X-band and THz frequency range. The porous Ti₃C₂T_X film showed higher EM absorption than that calculated using the transfer matrix method. On the other hand, the Ti₂CT_X films had a more densely stacked structure and lower EM absorption. As the heat treatment temperature increased, Ti₃C₂T_X developed a more porous structure without significant changes in its chemical bonding. Its EM absorption per unit of thickness increased up to 6 dB/μm, while the reflectance remained constant at less than 1 dB/μm after heat treatment. This suggested that the heat treatment of Ti-based MXenes can increase the porosity of the film by removing residual organics without changing the chemical bonds, thereby increasing electromagnetic shielding through absorption. Full article

Manual processing of lipoaspirate can enhance stem cell concentration, thereby improving the take rate, which still represents a major challenge in autologous fat transfer. However, since the preparation consists of many manual steps that are difficult to standardize, we investigated the influence of residual tumescent solution on the macroscopic and microscopic outcome of the mechanically processed lipoaspirate. Additionally, we investigated whether sedimentation followed by vacuum filtration of the aqueous phase could accelerate processing by replacing the initial centrifugation step. Samples with more than 5% remaining aqueous phase show no clearly defined oil phase, preventing any volume reduction. In contrast, all centrifuged samples produced a clear oil phase. The remaining tissue, as confirmed by both histology and viability assays, was superior to nanofat. Although sedimentation and filtration in the LipoCollector did not sufficiently separate enough aqueous phase from the lipoaspirate, tissue viability was significantly higher compared to our control container. Our findings indicate that centrifugation remains essential for effective aqueous phase separation and further mechanical processing, while the automatic filtration may enhance processing efficiency. These results indicate that further work is needed to simplify mechanical processing, as the outcome can be significantly influenced by parameters such as tumescent impurities. Full article