Next Article in Journal
A Multidisciplinary Approach to High Throughput Nuclear Magnetic Resonance Spectroscopy
Previous Article in Journal
Physical Layer Security Using Two-Path Successive Relaying
 
 
Search for Articles:
Title / Keyword
Author / Affiliation / Email
Journal
Article Type
 
 
Advanced Search
 
Section
Special Issue
Volume
Issue
Number
Page
 
Journals
Sensors
Volume 16
Issue 6
10.3390/s16060852
sensors-logo
Submit to this Journal Review for this Journal Propose a Special Issue
► Article Menu

Article Menu

share Share announcement Help format_quote Cite question_answer Discuss in SciProfiles thumb_up
...
Endorse textsms
...
Comment
first_page
settings
Order Article Reprints
Font Type:
Arial Georgia Verdana
Font Size:
Aa Aa Aa
Line Spacing:
Column Width:
Background:
Article

Quality Detection of Litchi Stored in Different Environments Using an Electronic Nose

by
Sai Xu
1,2,
Enli Lü
1,2,*,
Huazhong Lu
1,2,
Zhiyan Zhou
2,
Yu Wang
1,2,
Jing Yang
1,2 and
Yajuan Wang
1,2
1
Guangdong Engineering Research Center of Agricultural Product Cold Chain Logistics, South China Agricultural University, Guangzhou 510642, China
2
College of Engineering, South China Agricultural University, Guangzhou 510642, China
*
Author to whom correspondence should be addressed.
Sensors 2016, 16(6), 852; https://doi.org/10.3390/s16060852
Submission received: 31 January 2016 / Revised: 20 May 2016 / Accepted: 2 June 2016 / Published: 8 June 2016
(This article belongs to the Section Chemical Sensors)
Browse Figures
Versions Notes

Abstract

:
The purpose of this paper was to explore the utility of an electronic nose to detect the quality of litchi fruit stored in different environments. In this study, a PEN3 electronic nose was adopted to test the storage time and hardness of litchi that were stored in three different types of environment (room temperature, refrigerator and controlled-atmosphere). After acquiring data about the hardness of the sample and from the electronic nose, linear discriminant analysis (LDA), canonical correlation analysis (CCA), BP neural network (BPNN) and BP neural network-partial least squares regression (BPNN-PLSR), were employed for data processing. The experimental results showed that the hardness of litchi fruits stored in all three environments decreased during storage. The litchi stored at room temperature had the fastest rate of decrease in hardness, followed by those stored in a refrigerator environment and under a controlled-atmosphere. LDA has a poor ability to classify the storage time of the three environments in which litchi was stored. BPNN can effectively recognize the storage time of litchi stored in a refrigerator and a controlled-atmosphere environment. However, the BPNN classification of the effect of room temperature storage on litchi was poor. CCA results show a significant correlation between electronic nose data and hardness data under the room temperature, and the correlation is more obvious for those under the refrigerator environment and controlled-atmosphere environment. The BPNN-PLSR can effectively predict the hardness of litchi under refrigerator storage conditions and a controlled-atmosphere environment. However, the BPNN-PLSR prediction of the effect of room temperature storage on litchi and global environment storage on litchi were poor. Thus, this experiment proved that an electronic nose can detect the quality of litchi under refrigeratored storage and a controlled-atmosphere environment. These results provide a useful reference for future studies on nondestructive and intelligent monitoring of fruit quality.

1. Introduction

As a typical subtropical fruit, litchi (Litchi chinensis) is popular all around the world. However, its freshness, flavor and nutritive value decline quickly during the transportation and storage process. From a statistical point of view, the loss of litchi caused by natural decay accounts for more than 20% of the total amount of crop loss each year in China [1]. Investigation and research show that when the brown area of the surface of a litchi occupies 1/4 of the whole surface area, the flavor of the litchi will be seriously influenced, and the total soluble solid content will be decreased, resulting in a reduction in the market value [2]. However, accurate and rapid food quality detection can provide a scientific reference for quality grading, shelf management and consumption, thereby decreasing the losses caused by decay, which is vitally important to the perishable postharvest litchi.
Two commonly used quality detection methods already exist for litchi, namely, the sensory evaluation method [3,4] and the physicochemical indexes detection method [5,6]. The sensory evaluation method evaluates the quality of litchi via human vision, taste and smell. This method is time-consuming, destructive and laborious and is highly influenced by subjective factors. In addition, the physicochemical indexes detection method judges the quality of a litchi by detecting its physical indexes and chemical indexes. It is an intuitive and effective quality detection method, without interference from subjective factors, but the physicochemical indexes detection method suffers from being a complex operation (including the extraction of fruit juice and preparation of testing reagents, etc.), with low detection speed (it takes a long time to acquire the physicochemical indexes of the samples one at a time), a high level of effort (a tester must perform the whole testing process) and the need to damage the food itself, so this method cannot meet the need for non-destructive and intelligent detection (automated sampling and analysis to obtain the information for a sample without damage). That is to say, these two commonly used litchi quality detection methods cannot be applied in a massive litchi quality detection program during a practical period of massive litchi storage, and will damage litchi fruits. Therefore, it is reasonable to explore nondestructive and intelligent detection methods for the problem of detection of litchi quality, a problem which has not yet been solved.
Two existing nondestructive and intelligent food quality detection methods are the near-infrared spectroscopy method [7,8] and the electronic nose detection method [9,10]. The near-infrared spectroscopy method can quickly acquire external and internal quality information of samples. However, due to mutual shadowing among litchi fruit during storage, the difficulty of the overall detection is increased greatly. As a method simulating the biological sense of smell, the electronic nose is capable of effectively detecting both simple and complex volatiles, which avoids the influence of subjective factors and field angle. Compared with other detection methods that exist, the electronic nose is more suitable and provides a new means for the quality detection of litchi. Currently, the electronic nose technology has been applied to many fields of research for food quality detection, such as fruits [11,12], vegetables [13,14], meats [15,16] and nuts [17,18], and all of these studies have shown the feasibility of applying an electronic nose to detect food quality. However, research on the application of an electronic nose for the quality detection of litchi during storage has not yet been reported in any publication. The realization of litchi quality detection via an electronic nose can also provide a nondestructive and intelligent way for mass real-time monitoring of litchi quality which cannot be achieved by other existing food quality detection methods. In addition, a set of appropriate recognition algorithms (including feature extraction and pattern recognition) is important for intelligent detection. This research work also provides a reference for selecting recognition algorithms for the intelligent detection of litchi quality.
Our preliminary study found a high correlation between the electronic nose response and the physicochemical indexes for litchi [19]. However, whether the electronic nose can predict the quality of litchi requires further research. To explore the feasibility of using electronic nose technology for the quality detection of litchi, this study acquired both electronic nose data and physicochemical indexes of litchi stored in three different environments (room temperature, refrigerator and controlled-atmosphere) for different storage times. Then, the four different methods of linear discriminant analysis (LDA), canonical correlation analysis (CCA), back-propagation neural network (BPNN) and back-propagation neural network-partial least squares regression (BPNN-PLSR) were employed for data analysis. The main objectives of this study were the following: (1) validating the feasibility of the electronic nose for detecting and monitoring the change in quality of litchi stored in different environments; and (2) predicting the physicochemical index of litchi stored in different environments based on the electronic nose data.

2. Materials and Methods

2.1. Materials and Grouping

The experimental litchi samples (Guiwei, maturity grade is 8 to 9) were harvested from the Conghua litchi orchard, in Guangzhou (Guangdong, China), in July 2015. All litchi samples were transported to South China Agricultural University (SCAU, Guangzhou, Guangdong, China) within 2 h after harvesting. After removing the branches and leaves, undamaged litchi fruits of uniform size were selected. Then, they were randomly divided into three groups: the room temperature environment storage group, refrigerator environment storage group and controlled-atmosphere storage group. Before storage, litchies of the refrigerator environment and controlled-atmosphere storage groups were precooled [20] for 5 min using ice water (4 to 5 °C). Litchies for room temperature storage were not precooled considering that the decay rate of litchi will increase when transferring litchi from a cool to a warm environment [21]. Perforated polyethylene bags with a perforation ratio of 5% and a size of 300 mm × 200 mm × 0.05 mm were used to pack litchi samples, with 30 litchies per bag. All bags were bought from the SCAU market and manually punched with a hole punch. After that, all of the packed samples were put into plastic crates stored in the different environments. The room temperature storage environment was 25 °C; the refrigerator storage environment was 3 to 5 °C; the controlled-atmosphere storage environment was 3 to 5 °C at 90% to 95% relative humidity, 3% to 6% oxygen content.
Due to its fast decay, litchi stored at room temperature usually loses its commodity value within 5 days after harvest [2]. Thus, litchies in the room temperature environment were tested at 0, 1, 2, 3 and 4 days after harvest in this experiment. Because the refrigerator environment and controlled-atmosphere environment can extend the freshness lifetime of litchi [22], litchies in the refrigerator environment and controlled-atmosphere environment were tested at 0, 2, 4, 6 and 8 days after harvest. Thus, in this experiment, we tested electronic nose data and hardness for litchi during storage. Twenty samples from each storage environment were prepared for each test, so in total, this study obtained 300 sets of electronic nose data and 300 physicochemical indexes.

2.2. Experimental Storage Equipment

Air-conditioning (KFR-72LW, Gree Ltd., Zhuhai, China), a refrigerator (GX, Guangxiang Ltd., Guangzhou, China) and our laboratory-developed controlled-atmosphere storage platform [23] were used as the equipment for room temperature storage, refrigerator storage and controlled-atmosphere storage, respectively. The inside environment of the laboratory-developed controlled-atmosphere storage platform can be adjusted according to the requirements.

2.3. Electronic Nose Detection

A PEN3 portable electronic nose (Airsense Ltd., Schwerin, Germany) was employed in these experiments. This electronic nose system is mainly composed of sampling and cleaning channels, and a sensor array and pattern recognition unit. The sensor array is composed of 10 metal-oxide semiconductor-type chemical sensors, and their features are presented in Table 1. Each sample included one litchi fruit, and was enclosed in a 200-mL beaker, then sealed with plastic wrap for 0.5 h, and the electronic nose was used to sample its headspace. Beakers were washed using an ultrasonic cleaning instrument and cooled in the shade, and no peculiar aroma was detected. Before sampling, zero gas (room air that had been filtered through standard activated carbon) was pumped into the cleaning channel to normalize the gas sensors. The operating parameters of the electronic nose were setting at sampling interval of 1 s; flush time of 60 s; zero point trim time of 10 s; measurement time of 80 s; presampling time of 5 s; and injection flow of 300 mL/min.

2.4. Physicochemical Index Measurement

There are some studies focused on physicochemical index prediction of fruit such as soluble solids content [24], titratable acidity [25] and pH value [26], etc., based on electronic nose data. The hardness is an important quality index of fruit which is directly related to the taste [27], and often changes with the degree of freshness of fruit [28]. Some studies have focused on the correlation between electronic nose data and food hardness [29,30,31], and their results indicate the high correlation between electronic nose data and food hardness. However, whether the hardness of litchi can be predicted by an electronic nose has not yet been reported. Thus, this experiment tested the hardness as a quality index of litchi. After sampling by the electronic nose, the peel of litchi samples was removed immediately to measure the hardness of the pulp. The hardness measurement method applied in this experiment was the one proposed by Luo [32], and a portable fruit hardness tester (GY, Aidebao Ltd., Leqing, China) was used in these experiments. The average value of the hardness value for each sample was obtained from triplicate measurements.

2.5. Data Analysis Methods

2.5.1. LDA

LDA is one of the most commonly used classification procedures. The method maximizes the variance between categories and minimizes the variance within each single category. This method renders a certain number of orthogonal linear discriminant functions which equals the number of categories minus one [33].

2.5.2. CCA

CCA can focus on the relationship between two groups of variables [34]. The CCA analysis process involves building a linear combination for each group of variables based on the total variation of their original data matrixes, finding the most relevant aggregate variable (canonical correlation variable) from the linear combinations, and then, revealing the related properties of the two groups of variables via the canonical correlation variable. The correlation coefficient (r) and significance (sig) are two important parameters to judge the degree of correlation when using CCA for analysis. The definitional domain of r is [–1, 1]. The positive r value means positive correlation, and the negative value means a negative correlation. If the value of |r| is larger, the correlation is more significant. When the sig is less than 0.05, it means the correlation is significant. The smaller sig is, the more significant the correlation is. The “canoncorr” function tool of Matlab was used to perform the CCA analysis in this research.

2.5.3. BPNN

BPNN is one of the most widely employed ANN models [35]. It can be described as a non-linear projection between the input vectors and output vectors. A typical BPNN structure has three parts: one input layer, one hidden layer, and one output layer. In the process of training BPNN for analysis, the weights and threshold values of each layer are revised constantly, and this training lasts until the difference between the expected outputs and actual outputs is limited to a preliminary range or the scheduled training times are achieved.

2.5.4. PLSR

The partial least-squares regression (PLSR) is a technique used with data that contains correlated predictor variables. This technique constructs new predictor variables, known as components, as linear combinations of the original predictor variables. PLSR constructs these components while considering the observed response values, leading to a parsimonious model with reliable predictive power [36].

3. Results

3.1. Hardness Change of Litchi Stored in Three Environments

The change in hardness for the stored litchi in the three storage environments is shown in Figure 1. During storage, the hardness of all of the litchies decreased. In comparison, the litchi stored at room temperature had the fastest rate of decrease, followed by those in the refrigerator environment and controlled-atmosphere environment.

3.2. Change in Sensor Response Signal for Litchi Stored in Three Environments

To investigate the change in sensor response for litchi in different storage environments, the sensor response values in the 80th second were applied as each sample’s feature value. The average value of 20 samples was used as the sensor response value of each storage group (room temperature environment storage group, refrigerator environment storage group and controlled-atmosphere storage group) at a given storage time. The variation in the sensor response value for each storage group was measured on the 0th, 2nd and 4th day as presented in Table 2. On day 0, the differences in sensor response values between each storage group were small. However, after the 0th day, the electronic nose response value for the room temperature storage group changed greatly. In contrast, those of the refrigerator environment storage group and controlled-atmosphere storage group showed a slight change. With the increase in storage time, for litchi stored at room temperature, the response values of R1, R3, R5 and R10 were gradual; however, the response values of other sensors increased gradually. With an increase in storage time, for litchi stored in the refrigerator environment, the response values of R1, R3, R4, R5, R7 and R10 decreased gradually, and the response values of R8 and R10 first increased and then decreased, while the response values of the other sensors increased gradually. With an increased storage time for litchi stored in a controlled-atmosphere environment, the response values of R1, R3, R4 and R5 decreased gradually, and the response values of R7, R8 and R10 first increased and then decreased; in contrast, the response values of the other sensors increased gradually. Thus, according to the electronic nose response, the laws governing the change in volatiles in litchi stored in the three environments were different, which also proved the feasibility of using the electronic nose for detection of the changes in volatiles of litchi stored in different environments.

3.3. LDA for Storage Time Classification

In this study, three types of feature values were applied for pattern recognition: (1) the maximum value [37], the maximum value of a complete response value; (2) the average of the differential value [38], the average value of the differential of the electronic nose response curve for each sampling time; and (3) the 80th s value [39,40], the 80th s of each response curve. After feature extraction, those three feature values were tested by LDA.
The LDA analysis results of the storage time for the litchi stored at room temperature (from the 0th to the 4th day) based on the maximum values, the average of differential values and the 80th s values are shown in Figure 2a–c, respectively. When the maximum values were applied as the feature value of LDA analysis of the storage time for litchi stored in the room temperature environment (Figure 2a), all storage times overlap with others and cannot be classified. When the average of differential values was applied as the feature value for LDA analysis of litchi stored at room temperature (Figure 2b), none of the storage times can be classified, and the classification effect is poor. When the 80th s values were applied as the feature value for LDA analysis of storage time for the litchi stored at room temperature (Figure 2c), only the 4th day can be classified. Other storage times overlap with those of the other days, which shows that the classification effect is also unsatisfactory.
The LDA analysis results of the storage time for litchi stored in a refrigerator (from the 0th to the 8th day) based on the maximum values, the average of differential values and the 80th s values are shown in Figure 2d–f, respectively. When the maximum values were applied as the feature value for LDA analysis for the storage time for litchi stored in a refrigerator environment (Figure 2d), all storage times overlap with the others and cannot be classified. When the average of differential values was applied as the feature value for LDA analysis of the storage times for the litchies stored in the refrigerated environment (Figure 2e), none of the storage times can be classified, except those on the 0th and 5th day that were not overlapped by others. When the 80th s values were applied as the feature value for LDA analysis for the refrigerated environment storage group (Figure 2f), only the 0th and 5th day can be classified via this method. However, the 2nd, 4th, 6th and 8th day cannot be classified.
The LDA analysis results of the storage time for litchi stored under a controlled-atmosphere (from the 0th to the 8th day) based on the maximum values, the average of differential values and the 80th s values are shown in Figure 2g–i, respectively. When the maximum values were applied as the feature value for LDA analysis (Figure 2g), all of the storage times were overlapped by others except the 4th day that can be classified. When the average of the differential values was applied as the feature value for LDA analysis (Figure 2h), the 0th, 2nd and 8th days were not overlapped by any others and thus can be classified. However, the 4th and 6th cannot be classified. The data on the 4th and 6th days were overlapping each other and cannot be classified. When the 80th s values were applied as the feature value for LDA analysis (Figure 2h), the 0th, 2nd, and 8th days can be classified. However, the 4th day and 6th day overlap each other and cannot be classified.
Based on the analysis results above, the storage time classification effect of litchi stored in the controlled-atmosphere environment is the best, followed the by refrigerator environment and room temperature environment. In addition, according to the classification effect based on different feature values, the classification effects based on the average of differential values and the 80th s values were clearly better than the maximum values. The study of Hu et al. found that the total discriminant factor contribution is higher and that the classification effect is better [41]. Thus, we selected average of the differential values (which has the highest total contribution of LD1 and LD2) as the feature value for the next analysis in this experiment.

3.4. BPNN for Storage Time Classification

Because the classification effect of the linear identification method (LDA) for storage time is not satisfactory, this study applied a nonlinear identification method (BPNN) for further classification. There are 20 samples tested at five storage times for each environment group. The experiment selected 15 samples randomly from 20 samples of each storage time for each environment group as a training set. The remaining five samples from the 20 samples are the test set. Thus, the training set includes 75 samples in total, and the test set includes 25 samples in total. We ranked the expected output of five storage times for each storage environment from small to large. They are (1, 0, 0, 0, 0), (0, 1, 0, 0, 0), (0, 0, 1, 0, 0), (0, 0, 0, 1, 0), (0, 0, 0, 0, 1). After repeated training, the model parameters and recognition accuracy are given in Table 3. The classification accuracy of training sets of the room temperature environment storage group, the refrigerator environment storage group and the controlled-atmosphere storage group are 89.33%, 100% and 100%, respectively. The classification accuracy of test sets of the room temperature environment storage group, the refrigerator environment storage group and the controlled-atmosphere storage group are 52%, 88% and 96%, respectively. Thus, the storage time of the refrigerator environment and the controlled-atmosphere stored litchi can be classified effectively via the electronic nose. However, the storage time classification effect of litchi stored in the room temperature environment is still poor.

3.5. CCA for Correlation Analysis between Electronic Nose Data and Hardness of Litchi

In this experiment, the CCA was applied to test the correlation between electronic nose data and hardness of litchi stored in three environments, and the “canoncorr” function command of Matlab was used to perform the CCA analysis. The CCA plots (Figure 3) illustrate a strong linear correlation between the canonical correlation variable of the sensor response data and the canonical correlation variable of the hardness values, indicating that the electronic nose response were linearly correlated with hardness values of litchi stored in the three environments. The |r| values between the electronic nose data and the hardness of litchi stored in the room temperature environment, the refrigerator environment and the controlled-atmosphere environment are 0.5919 (sig = 1.29 × 10−2), 0.7104 (sig = 8.85 × 10−3) and 0.7439 (sig = 8.04 × 10−3), respectively. Thus, CCA results show a significant correlation (|r| > 0.5, sig < 0.05) between electronic nose data and hardness data under the room temperature, and the correlation is more obvious (|r| > 0.7, sig < 0.01) for those under the refrigerator environment and controlled-atmosphere environment.

3.6. BPNN-PLSR for Hardness Prediction

To study the prediction effect of the physicochemical index of the litchi during its storage based on the electronic nose, this study applied BPNN-PLSR for hardness prediction of litchi stored in the three different environments. We used the same training set and test set as the BPNN analysis for storage time classification in this research. In addition, a global model (mixed litchi samples stored in all three environments were used for model training) was also be built instead of the three separate models to try to simplify the prediction process. We chose 75 samples randomly from each environment storage group as the training set of global environment storage group, and 25 samples were randomly selected from the remaining samples of each environment storage group as the test set of the global environment storage group. The expected outputs are the actual hardness of the litchi. The process of BPNN-PLSR for hardness prediction is: (1) build a BPNN model for hardness prediction; (2) obtain the predicted hardness value via the BPNN prediction model; and (3) apply PLSR for fitting the predicted hardness value and the actual hardness value and determining litchi’s physicochemical index prediction effect according to the PLSR fitting result. The training parameters of the BPNN prediction model after repeated training for three storage environments are shown in Table 4.
When PLSR is used for regression fitting, the fitting correlation coefficient (R2) and the root mean square error (RMSE) are two important indexes for judging the correlation effect. It is noted that according to [37], if the R2 value is greater than 0.8, this demonstrates that the prediction value has a high correlation with the actual value. If the R2 is closer or further from 1, the correlation is higher or lower, respectively. However, if the R2 is lower than 0.8, this demonstrates that the prediction value has a low correlation with the actual value and that the prediction is unfeasible. In addition, the closer the RSME value is to 0, the better the prediction effect. The BPNN-PLSR hardness prediction effects are illustrated in Figure 4.
The BPNN-PLSR hardness prediction results of the training set and the test set for the room temperature environment storage group are shown in Figure 4a,b, respectively. For the BPNN-PLSR hardness prediction results of the training set of the room temperature environment stored litchi, the R2 and RMSE values are 0.61 and 0.25, respectively. For the BPNN-PLSR hardness prediction results for the test set of the room temperature environment storage group, the R2 and RMSE are 0.73 and 0.17, respectively. Thus, the quality-prediction effect of the electronic nose for the room temperature environment storage group is weak (the R2 values of the training set and test set are less than 0.8). The BPNN-PLSR hardness prediction results of the training set and the test set of the refrigerator environment storage group are shown in Figure 4c,d, respectively. For the BPNN-PLSR hardness prediction results of the training set of the refrigerator environment storage group, the R2 and RMSE values are 0.82 and 0.08, respectively. For the BPNN-PLSR hardness prediction results of the test set of the refrigerator environment storage group, the R2 and RMSE values are 0.81 and 0.08, respectively. Thus, it is feasible to apply the electronic nose for the prediction of the quality of litchi stored in a refrigerator environment (the R2 values of the training set and test set are greater than 0.8). The BPNN-PLSR hardness prediction results of the training set and the test set of the controlled-atmosphere environment storage group are shown in Figure 4e,f, respectively. For the BPNN-PLSR hardness prediction results of the training set of the controlled-atmosphere environment storage group, the values if R2 and RMSE are 0.85 and 0.06, respectively. For the BPNN-PLSR hardness prediction results of the test set of the controlled-atmosphere environment storage group, the values of R2 and RMSE are 0.86 and 0.07, respectively. Thus, the quality prediction effect of the electronic nose for litchi stored in a controlled-atmosphere environment is good (the R2 values of the training set and test set are not less than 0.85). Thus, the electronic nose can effectively predict the hardness of stored litchi in a controlled-atmosphere environment and refrigerator environment. However, the prediction effect of hardness at room temperature is poor. The BPNN-PLSR hardness prediction results of the training set and the test set for the global group are shown in Figure 4g,h, respectively. For the BPNN-PLSR hardness prediction results of the training set of the global environment stored litchi, the R2 and RMSE values are 0.67 and 0.13, respectively. For the BPNN-PLSR hardness prediction results for the test set of the global environment storage litchi, the R2 and RMSE are 0.67 and 0.12, respectively. Thus, the quality-prediction effect of the electronic nose for the room temperature environment storage group is weak (the R2 values of the training set and test set are less than 0.8).

4. Discussion

This experiment explored the feasibility of using an electronic nose for the detection of the quality litchi fruits stored in different environments (a room temperature environment, refrigerator environment and controlled-atmosphere environment). The experimental results show that the electronic nose can effectively recognize the storage time and hardness of litchi stored in a refrigerator environment and controlled-atmosphere environment. However, the storage time and hardness detection effect of litchi stored in a room temperature environment based on the electronic nose is poor.
The hardness of litchi in the three environments gradually decreased with increasing storage time. The hardness of the litchi stored in the room temperature environment has the fastest rate of decrease, followed by the litchi stored in the refrigerator environment and controlled-atmosphere environment. Research by Yang et al. [41] showed that the hardness of litchi usually decreases gradually during storage due to the influence of respiration and enzymatic degradation of the cell wall. The decrease in hardness is important in demonstrating the ripening and aging of the litchi. Thus, compared with a room temperature environment, the controlled-atmosphere environment and refrigerator environment can better inhibit the rate of respiration intensity and the formation of enzymes that degrade the cell wall and can slow the litchi aging process. The research results of this study showed that among the three storage environments, the storage effect of the controlled-atmosphere environment is the best, followed by the refrigerator environment and room temperature environment.
LDA is poor for storage time classification of litchi stored in the three environments. However, BPNN is useful for storage time classification of litchi stored in the refrigerator and controlled-atmosphere environments. The classification effect of BPNN is better than LDA for storage time classification of litchi. The reason is that LDA is a linear classification method, the classification performance of LDA is based on the sample’s distribution in two-dimensional space. However, BPNN is a nonlinear classification method that can achieve arbitrary nonlinear mapping from input to output. BPNN displays good performance when applied to functional mapping, functional approximation and self-adaption. Thus, the BPNN is better than LDA for nonlinear problems, such as litchi’s quality classification. LDA is used to preliminarily observe the classification effect and the distribution of electronic nose response data points.
The electronic nose can effectively recognize quality information for litchi stored in a refrigerator environment or controlled-atmosphere environment. However, the quality information reorganization effect of litchi stored in a room temperature environment and global environment are poor. Research by Cai et al. [42] indicated the differences of volatile compositions and relative contents of frozen and not frozen litchi, which tallied with the results of the sensors’ response value changes for litchi stored in the three different environments. As we know, the electronic nose is an instrument for detection according to a sample’s volatiles. However, not all volatiles in a sample have great contributions to the electronic nose detection, and some of them may disturb the classification and recognition. Thus, future research can use gas chromatography-mass spectrometry (GC-MS) to explore in detail the volatile changes in litchi stored in different environments. To further improve the quality detection accuracy of litchi via the electronic nose, several gas sensors sensitive to the volatiles (which have a remarkable variation trend during storage according to the GC-MS results) can be selected and combined with a suitable recognition algorithm to set up a specialized recognition device for the intelligent detection of litchi quality.
During the practical process of storing litchi, from the transportation after harvest to the market, a refrigerator environment and controlled-atmosphere environment are the main means of storage. Storage in a room temperature environment usually only occurs in the sales of small quantities of litchi. These experimental results show that it is feasible to use an electronic nose combined with the BPNN analysis method for quality detection of litchi stored in refrigerator and controlled-atmosphere environments.

5. Conclusions

This experiment applied electronic nose technology for storage time classification and hardness prediction of litchi in different environments (room temperature environment, refrigerator environment and controlled-atmosphere environment). The electronic nose can effectively detect the quality of litchi stored in a refrigerator environment and controlled- atmosphere environment. The quality detection effect of litchi stored in a room temperature environment is poor. The details are as follows:
(1)
The hardness of litchi decreases with an increase in storage time. However, the decrease rate in order from fast to slow is room temperature, in a refrigerator environment and in a controlled-atmosphere environment.
(2)
The LDA classification effects of the three litchi storage environments on storage time were poor. Comparatively, the classification effect of litchi in a controlled-atmosphere environment is the best, followed by those in the refrigerator environment and room temperature environment.
(3)
According to the LDA classification effect, by using the feature extraction methods such as the maximum value method, average of differential value method and the 80th s value method, the classification effect is the best when using the average of differential value method.
(4)
BPNN can effectively recognize the storage time of litchi stored in a refrigerator and controlled-atmosphere environment, but its recognition of litchi stored in a room temperature environment is poor. The classification accuracy of the training sets of the room temperature environment storage group, the refrigerator environment storage group and the controlled-atmosphere storage group are 89.33%, 100% and 100%, respectively. The classification accuracy of the test sets of the room temperature environment storage group, the refrigerator environment storage group and the controlled-atmosphere storage group are 52%, 88% and 96%, respectively.
(5)
CCA results show a significant correlation between electronic nose data and hardness data under room temperature, and the correlation is more obvious for those under the refrigerator environment and controlled-atmosphere environment. The BPNN-PLSR prediction effect of hardness for litchi in either a refrigerated or controlled-atmosphere environment is good, but it is poor for that in a room temperature environment and in a global environment.
(6)
According to the research results of this study, among the three storage environments, the storage effect of the controlled-atmosphere environment is the best, followed by those of the refrigerator environment and room temperature environment.

Acknowledgments

The authors thank the College Outstanding Young Teacher Training Program in Guangdong Province of China (Y92014025), National Natural Science Foundation of China (Project No. 31571561) and the Modern Agricultural Industry Technology System Construction Special Foundation of China (Project No. CARS-33-13) for financing this research.

Author Contributions

E.L. designed the reported study, evaluated the results, prepared and reviewed the manuscript. J.Y. and Y.J.W. helped S.X. to conduct the experiments. S.X. is responsible for the entire experiment, analysed the results, and prepared the manuscript. H.L. contributed to planning the reported research, evaluate the results, review and approve the manuscript. Z.Z. helped in preparing the experimental setup. Y.W. revised the manuscript. All authors both read and approved the manuscript.

Conflicts of Interest

The authors declare no conflict of interest.

References

  1. Zou, Y.F.; Xie, R.H.; Qiu, Z.Q. Safety assessment of lichee cold chain logistics system based on go-flow methodology. Ind. Eng. J. 2008, 11, 47–49. [Google Scholar]
  2. Zhou, X.; Chen, Y.; Tang, J.; Huang, S.; Cao, Y. Loss estimation of litchi fruit due to pericarp browning. Chin. J. Trop. Crops 2012, 1403–1408. [Google Scholar]
  3. Zhang, Z.Q.; Pang, X.Q. Change of anthocyanin content and its determination during lychee pericarp browning. J. South China Agric. Univ. 2002, 23, 16–19. [Google Scholar]
  4. Scott, K.J.; Brown, B.I.; Chaplin, G.R.; Wilcox, M.E.; Bain, J.M. The control of rotting and browning of litchi fruit by hot benomyl and plastic film. Sci. Hortic.-Amst. 1982, 16, 253–262. [Google Scholar] [CrossRef]
  5. Singh, P.; Singh, I.S. Physico-chemical changes during storage of litchi (Litchi chinensis) beverages. Indian J. Agric. Sci. 1994, 64, 168–170. [Google Scholar]
  6. Singh, B.; Chadha, K.L.; Sahai, S. Performance of litchi cultivar for yield and physico-chemical quality of fruits. Indian J. Hortic. 2010, 67, 96–98. [Google Scholar]
  7. Zhou, L.J.; Wu, H.; Li, J.T.; Wang, Z.Y.; Zhang, L.Y. Determination of fatty acids in broiler breast meat by near-infrared reflectance spectroscopy. Meat Sci. 2012, 90, 658–664. [Google Scholar] [CrossRef] [PubMed]
  8. Barbin, D.; Elmasry, G.; Sun, D.; Allen, P. Near-infrared hyperspectral imaging for grading and classification of pork. Meat Sci. 2012, 90, 259–268. [Google Scholar] [CrossRef] [PubMed]
  9. Ghasemi-Varnamkhasti, M.; Aghbashlo, M. Electronic nose and electronic mucosa as innovative instruments for real-time monitoring of food dryers. Trends Food Sci. Technol. 2014, 38, 158–166. [Google Scholar] [CrossRef]
  10. Roy, R.B.; Tudu, B.; Shaw, L.; Jana, A.; Bhattacharyya, N.; Bandyopadhyay, R. Instrumental testing of tea by combining the responses of electronic nose and tongue. J. Food Eng. 2012, 110, 356–363. [Google Scholar]
  11. Baietto, M.; Wilson, A.D. Electronic-nose applications for fruit identification, ripeness and quality grading. Sensors 2015, 15, 899–931. [Google Scholar] [CrossRef] [PubMed]
  12. Hui, G.H.; Wu, Y.L.; Ye, D.D.; Ding, W.W. Fuji apple storage time predictive method using electronic nose. Food Anal. Method 2013, 6, 82–88. [Google Scholar]
  13. Messina, V.; Domínguez, P.G.; Sancho, A.M.; Walsöe De Reca, N.; Carrari, F.; Grigioni, G. Tomato quality during short-term storage assessed by colour and electronic nose. Int. J. Electrochem. 2012, 2012, 687429. [Google Scholar] [CrossRef]
  14. Zhou, Y.B.; Wang, J. Evaluation of maturity and shelf life of tomato using an electronic nose. Trans. Chin. Soc. Agric. Eng. 2005, 4, 25. [Google Scholar]
  15. Tian, X.; Wang, J.; Cui, S. Analysis of pork adulteration in minced mutton using electronic nose of metal oxide sensors. J. Food Eng. 2013, 119, 744–749. [Google Scholar] [CrossRef]
  16. Wang, D.; Wang, X.; Liu, T.; Liu, Y. Prediction of total viable counts on chilled pork using an electronic nose combined with support vector machine. Meat Sci. 2012, 90, 373–377. [Google Scholar] [CrossRef] [PubMed]
  17. Yoshida, K.; Ishikawa, E.; Joshi, M.; Lechat, H.; Ayouni, F.; Bonnefille, M. Quality control and rancidity tendency of nut mix using an electronic nose. In Perception and Machine Intelligence; Springer: Kolkata India, 2012; pp. 163–170. [Google Scholar]
  18. Osborn, G.S.; Lacey, R.E.; Singleton, J.A. A method to detect peanut off-flavors using an electronic nose. Trans. ASAE 2001, 44, 929–938. [Google Scholar]
  19. Xu, S.; Lu, H.Z.; Zhou, Z.Z.; Lü, E.L.; Jiang, Y.M.; Wang, Y.J. Identification of litchi’s maturing stage in orchard based on physicochemical indexes and electronic nose. Trans. Chin. Soc. Agric. Mach. 2015, 46, 226–232. [Google Scholar]
  20. Ruan, W.; Liu, B.; Song, X. Comparison of cooling method for litchi fruit. Sci. Technol. Food Ind. 2012, 33, 352–353. [Google Scholar]
  21. Chen, H.; Wang, Y.; Peng, Y. Shelf-quality and physiological indices of litchi subjected to cool storage. Subtrop. Plant Sci. 2001, 3, 2. [Google Scholar]
  22. Mahajan, P.V.; Goswami, T.K. Extended storage life of litchi fruit using controlled atmosphere and low temperature. J. Food Process. Preserv. 2004, 28, 388–403. [Google Scholar] [CrossRef]
  23. Guo, J.M.; Lv, E.L.; Lu, H.Z.; Li, Y.H.; Zheng, Z.X. Relationship between color index a* value and other quality indicators of litchi pericarp during storage. Modern Food Sci. Technol. 2014, 30, 68–73. [Google Scholar]
  24. Zhang, W.; Pan, L.; Zhao, X.; Tu, K. A Study on Soluble Solids Content Assessment Using Electronic Nose: Persimmon Fruit Picked on Different Dates. Int. J. Food Prop. 2016, 19, 53–62. [Google Scholar] [CrossRef]
  25. Sanaeifar, A.; Mohtasebi, S.S.; Ghasemi-Varnamkhasti, M.; Ahmadi, H. Application of MOS based electronic nose for the prediction of banana quality properties. Measurement 2016, 82, 105–114. [Google Scholar] [CrossRef]
  26. Qiu, S.; Wang, J.; Gao, L. Discrimination and characterization of strawberry juice based on electronic nose and tongue: Comparison of different juice processing approaches by LDA, PLSR, RF, and SVM. J. AGR Food Chem. 2014, 62, 6426–6434. [Google Scholar] [CrossRef] [PubMed]
  27. Harker, F.R.; Amos, R.L.; Echeverríaa, G.; Gunson, F.A. Influence of texture on taste: Insights gained during studies of hardness, juiciness, and sweetness of apple fruit. J. Food Sci. 2006, 71, S77–S82. [Google Scholar] [CrossRef]
  28. Zhang, Y. Combined technology of kiwifruit storage and freshness-keeping with freshness-keeping reagent at low temperature and modified atmosphere. Trans. Chin. Soc. Agric. Eng. 2001, 18, 138–141. [Google Scholar]
  29. Di Natale, C.; Macagnano, A.; Martinelli, E.; Proietti, E.; Paolesse, R.; Castellari, L.; Campani, S.; D’Amico, A. Electronic nose based investigation of the sensorial properties of peaches and nectarines. Sens. Actuat. B: Chem. 2001, 77, 561–566. [Google Scholar] [CrossRef]
  30. Lee, Y.; Kum, J.; Ahn, Y.; Kim, W. Effect of packaging material and oxygen absorbant on quality properties of Yukwa. Korean J. Food Sci. Technol. 2001, 33, 728–736. [Google Scholar]
  31. Li, Y.; Ren, Y.M.; Zhang, S.; Zhao, H.; Zhou, L.A.; Ren, X.L. Prediction of low-temperature storage time and quality of apples based on electronic nose. J. Northwest A&F Univ. (Nat. Sci. Ed.) 2015, 43, 183–191. [Google Scholar]
  32. Luo, J.; Tian, L.P.; Zhang, C.; Xue, L. Analysis of firmness and related characters of processing tomato. Chin. Agric. Sci. Bull. 2011, 27, 217–220. [Google Scholar]
  33. Buratti, S.; Benedetti, S.; Scampicchio, M.; Pangerod, E.C. Characterization and classification of Italian Barbera wines by using an electronic nose and an amperometric electronic tongue. Anal. Chim. Acta 2004, 525, 133–139. [Google Scholar] [CrossRef]
  34. Aleixandre, M.; Santos, J.P.; Sayago, I.; Cabellos, J.M.; Arroyo, T.; Horrillo, M.C. A Wireless and Portable Electronic Nose to Differentiate Musts of Different Ripeness Degree and Grape Varieties. Sensors (Basel) 2015, 15, 8429–8443. [Google Scholar] [CrossRef] [PubMed]
  35. Hong, X.; Wang, J.; Hai, Z. Discrimination and prediction of multiple beef freshness indexes based on electronic nose. Sens. Actuators B Chem. 2012, 161, 381–389. [Google Scholar] [CrossRef]
  36. Wei, Z.; Wang, J.; Zhang, W. Detecting internal quality of peanuts during storage using electronic nose responses combined with physicochemical methods. Food Chem. 2015, 177, 89–96. [Google Scholar] [CrossRef] [PubMed]
  37. Brudzewski, K.; Osowski, S.; Dwulit, A. Recognition of coffee using differential electronic nose. IEEE Trans. Instrum. Meas. 2012, 61, 1803–1810. [Google Scholar] [CrossRef]
  38. Yu, H.; Wang, J. Discrimination of LongJing green-tea grade by electronic nose. Sens. Actuators B Chem. 2007, 122, 134–140. [Google Scholar] [CrossRef]
  39. Saurina, J.; López-Aviles, E.; Le Moal, A.; Hernández-Cassou, S. Determination of calcium and total hardness in natural waters using a potentiometric sensor array. Anal. Chim. Acta 2002, 464, 89–98. [Google Scholar] [CrossRef]
  40. Hu, G.; Wang, J.; Wang, J.; Wang, X. Detection for rice odors and identification of varieties based on electronic nose technique. J. Zhejiang Univ. (Agric. Life Sci.) 2011, 6, 13. [Google Scholar]
  41. Yang, S.; Lv, E.; Lu, H.; Zeng, Z.; Tang, B. Effects of different fresh-keeping transportation modes on quality of litchi fruit. Trans. Chin. Soc. Agric. Eng. 2014, 30, 225–232. [Google Scholar]
  42. Cai, C.; Chen, Y.; Zeng, Q.; Zhang, A. Study on effects of freezing treatment on aroma components in litchi fruit. Food Sci. 2008, 29, 557–561. [Google Scholar]
Sensors 16 00852 g001 1024
Figure 1. Change in hardness of litchi stored in the three environments.
Figure 1. Change in hardness of litchi stored in the three environments.
Sensors 16 00852 g001
Sensors 16 00852 g002 1024
Figure 2. LDA analysis results of litchies stored in different environments based on (a,d,g) the maximum value; (b,e,h) the average of the differential values; (c,f,i) the 80th s value. (a–c) are the LDA analysis results of the room temperature storage group (d), (e) and (f) are the LDA analysis results of the refrigerator environment storage group; (g–i) are the LDA analysis results of the controlled-atmosphere environment storage group. Note: LD1 is the contribution rate of the first linear discriminant factor, LD2 is the contribution rate of the second linear discriminant factor.
Figure 2. LDA analysis results of litchies stored in different environments based on (a,d,g) the maximum value; (b,e,h) the average of the differential values; (c,f,i) the 80th s value. (a–c) are the LDA analysis results of the room temperature storage group (d), (e) and (f) are the LDA analysis results of the refrigerator environment storage group; (g–i) are the LDA analysis results of the controlled-atmosphere environment storage group. Note: LD1 is the contribution rate of the first linear discriminant factor, LD2 is the contribution rate of the second linear discriminant factor.
Sensors 16 00852 g002
Sensors 16 00852 g003 1024
Figure 3. The CCA plot of electronic nose data and hardness of litchi stored in (a) the room temperature environment; (b) the refrigerator environment; and (c) the controlled-atmosphere environment. Note: The CCVS is the canonical correlation variable of the sensor response data, the CCVH is the canonical correlation variable of the hardness values.
Figure 3. The CCA plot of electronic nose data and hardness of litchi stored in (a) the room temperature environment; (b) the refrigerator environment; and (c) the controlled-atmosphere environment. Note: The CCVS is the canonical correlation variable of the sensor response data, the CCVH is the canonical correlation variable of the hardness values.
Sensors 16 00852 g003
Sensors 16 00852 g004 1024
Figure 4. Hardness prediction results of litchi stored in different environments based on BPNN-PLSR. (a) Training set of litchi stored at room temperature; (b) test set of room temperature storage group; (c) training set of the refrigerator environment storage group; (d) test set of refrigerator environment storage group; (e) training set of the controlled-atmosphere environment storage group; (f) test set of the controlled-atmosphere environment storage group; (g) training set of the global environment storage group; (f) test set of the global environment storage group.
Figure 4. Hardness prediction results of litchi stored in different environments based on BPNN-PLSR. (a) Training set of litchi stored at room temperature; (b) test set of room temperature storage group; (c) training set of the refrigerator environment storage group; (d) test set of refrigerator environment storage group; (e) training set of the controlled-atmosphere environment storage group; (f) test set of the controlled-atmosphere environment storage group; (g) training set of the global environment storage group; (f) test set of the global environment storage group.
Sensors 16 00852 g004
Table
Table 1. Response features of the sensor array.
Table 1. Response features of the sensor array.
Number in ArraySensor NameObject Substances for SensingThreshold Value (mL·m−3)
R1W1CAromatics10
R2W5SNitrogen oxides1
R3W3CAmmonia and aromatic molecules10
R4W6SHydrogen100
R5W5CMethane, propane and aliphatic non-polar molecules1
R6W1SBroad methane100
R7W1WSulfur-containing organics1
R8W2SBroad alcohols100
R9W2WAromatics, sulfur-and chlorine-containing organics1
R10W3SMethane and aliphatics10
Table
Table 2. Sensor response signal data for litchi in different storage environments.
Table 2. Sensor response signal data for litchi in different storage environments.
TimeStorage GroupsR1R2R3R4R5R6R7R8R9R10
0dRT0.3132.4480.4861.1030.5426.422630.5584.9363.3161.214
RE0.3942.2630.5741.0890.6334.491583.5613.6602.7591.114
CA0.3512.3050.5211.3880.5805.057552.2933.8762.7401.109
2dRT0.2414.3770.3841.1210.4339.3372601.4096.2954.6481.202
RE0.3432.6800.5111.0780.5726.080526.3324.4872.9741.158
CA0.3022.6630.4731.1690.5356.347355.4195.063.1291.168
4dRT0.16613.5310.2621.1540.28612.3475873.8427.48717.0221.184
RE0.3282.7390.4761.0640.5365.641389.6354.1853.1431.116
CA0.2732.7380.4011.1520.4686.63275.8874.7543.2061.100
Note: RT is the room temperature environment storage group, RE is the refrigerator environment storage group, and CA is the controlled-atmosphere storage group.
Table
Table 3. BPNN classification results of storage times of litchi stored in three environments.
Table 3. BPNN classification results of storage times of litchi stored in three environments.
Storage GroupsInput LayersHidden LayerOutput LayersLearning FactorDynamic FactorTraining TimesAccuracy/%
Training SetTest Set
RT101950.050.8520,00089.3352
RE102150.0250.7520,00010088
CA101850.050.8520,00010096
Note: RT is the room temperature environment storage group, RE is the refrigerator environment storage group, and CA is the controlled-atmosphere storage group.
Table
Table 4. Training parameters of BPNN hardness prediction models for different storage environments.
Table 4. Training parameters of BPNN hardness prediction models for different storage environments.
Storage GroupsInput LayersHidden LayerOutput LayersLearning FactorDynamic FactorTraining Times
RT1023750.050.8720,000
RE1025750.0550.8720,000
CA1023750.0450.8020,000
GL1025750.430.8720,000
Note: RT is the room temperature environment storage group, RE is the refrigerator environment storage group, CA is the controlled-atmosphere storage group, and GL is the global environment storage group.

Share and Cite

MDPI and ACS Style

Xu, S.; Lü, E.; Lu, H.; Zhou, Z.; Wang, Y.; Yang, J.; Wang, Y. Quality Detection of Litchi Stored in Different Environments Using an Electronic Nose. Sensors 2016, 16, 852. https://doi.org/10.3390/s16060852

AMA Style

Xu S, Lü E, Lu H, Zhou Z, Wang Y, Yang J, Wang Y. Quality Detection of Litchi Stored in Different Environments Using an Electronic Nose. Sensors. 2016; 16(6):852. https://doi.org/10.3390/s16060852

Chicago/Turabian Style

Xu, Sai, Enli Lü, Huazhong Lu, Zhiyan Zhou, Yu Wang, Jing Yang, and Yajuan Wang. 2016. "Quality Detection of Litchi Stored in Different Environments Using an Electronic Nose" Sensors 16, no. 6: 852. https://doi.org/10.3390/s16060852

APA Style

Xu, S., Lü, E., Lu, H., Zhou, Z., Wang, Y., Yang, J., & Wang, Y. (2016). Quality Detection of Litchi Stored in Different Environments Using an Electronic Nose. Sensors, 16(6), 852. https://doi.org/10.3390/s16060852

Note that from the first issue of 2016, this journal uses article numbers instead of page numbers. See further details here.

Article Metrics

Back to TopTop