1. Introduction
Nowadays, 5G sub-6-GHz systems demand very high-speed transmission rates in order to be able to deliver the always increasing amount of data that are generated by millions of users around the world. This means that transmitters must cover large ranges of frequencies, and so they make use of a power amplifier (PA), which is responsible for increasing the wave energy with minimum waste, after the modulation process. Therefore, solutions to design high efficiency and wideband PAs are a challenge that is always present in the deployment of new communication networks.
In the literature, several approaches found hybrid PAs with a good efficiency for bandwidths wider than an octave. For instance, in [
1], a high efficiency PA with 145.5% fractional bandwidth was obtained using a simplified device model. A 153.2% fractional bandwidth PA was obtained in [
2], where an estimation of the power and efficiency contours was carried out in order to visualize a broadband output matching network (OMN). The design process shown in [
3] used an optimization algorithm to design a broadband PA with equalized gain over the band, and a 145.6% fractional bandwidth was obtained. In [
4], a design process based on L-sections was proposed, obtaining a high efficiency over a 152.9% fractional bandwidth. In addition, other methodologies have been implemented such as the real frequency technique [
5,
6,
7], wideband class J [
8], and class E [
9], among other harmonic tuned PAs.
This paper presents an approach to design ultrawideband power amplifiers using a simple OMN, focused only on the fundamental optimal load. This involves the use of a series transmission line, a shunt stub, and a multisection transformer. Two examples, using two different GaN HEMT devices, are theoretically studied, and one of them is implemented and characterized as a demonstration circuit. The characterization of the implemented amplifier shows state-of-the-art results in terms of high-efficiency bandwidth. Its bandwidth extends from very low frequencies (i.e., 0.1 GHz) to 4 GHz, which means that the PA covers 67% of the 5G sub-6-GHz band. The obtained drain efficiency is between 52 and 70.7% over the band. A comparison with other state-of-the-art works is presented in
Table 1.
2. Output Network Topology and Bandwidth Estimation
In [
10,
11], the effective use of an equivalent output reactive network was used to estimate the load dispersion, with respect to frequency, in high frequency field effect transistors (FET). This simplified method proposes a network formed by a shunt capacitor
and a series inductor
, which separates the drain current generator and the drain pin plane. Usually, these two reactive elements are referred to as the output parasitics or the parasitic output network of the device. They are an unavoidable characteristic of the device, which must be considered as part of the output matching network (OMN) or as something undesirable to be compensated for.
Based on the above, this was the start point in this work. Whether the parasitic output network is well compensated for a large bandwidth, is an important concept to exploit, as this bandwidth can in theory be achieved, because with a wideband, real to real matching is possible through a multi-section transformer. Let us consider a reference frequency
, which is used for all of the calculations presented in the following equations. It can be demonstrated that a simple network involving a series transmission line and an open shunt sufficiently compensate the parasitic effects through the correct selection of their electrical lengths and characteristic admittances. Moreover, the bandwidth will be directly related to
. Thus, the proposed solution is shown in
Figure 1, where
is the drain current, and the elements
and
represent the estimated output parasitic network of the device.
Therefore, the design consists of finding the appropriate values for the transmission lines’ characteristic admittances and electrical lengths. As the function of the distributed network is to compensate
and
, the value of the real load
is chosen as
, where
is the optimal load for tuned load conditions in order to simultaneously obtain the voltage and current saturation (i.e.,
). Looking at
Figure 1, the external load admittance at the drain pin is given by
where
and
.
However, the optimal external load to perfectly compensate for the parasitic effects
and
,
must be equal to
Thus, the solution for the reference frequency
is obtained by equalizing (1) and (2), which leads to the following pair of equations,
Solving (3) and (4) for
, a quadratic equation is obtained,
Therefore,
is given by
The sign before the square root is chosen to obtain a positive value for
, and the electrical length
is obtained as
As shown in
Figure 1,
is assumed to guarantee the optimal load, even at very low frequencies. Now, using (3),
and the electrical length
is given by
Notice that (7) and (9) depend on the characteristic admittances
and
. In this framework, they are left as the free selection variables. However, an estimation of the bandwidth is recommended to evaluate the selection of these variables. To this purpose, as a criterion for estimating the bandwidth, the following intrinsic reflection coefficient is defined as
with
Thus, the bandwidth here is defined by , the maximum value of that can be tolerated.
3. Design and Implementation
Let us consider two different devices to demonstrate the effectiveness of the design equations proposed in
Section 2. These are the Wolfspeed (Durham, NC, USA) CG2H40010 and CG2H40025 GaN HEMT devices.
Table 2 shows the values for
and
for both devices, respectively.
In this case,
is selected in order to match the physical dimensions of the device’s drain pin. Both devices have a drain pin width of
. Hence,
is a good selection for a Taconic RF35 substrate with
and 0.76 mm in height. This value ensures the needed soldering space at the drain pin.
is chosen only looking at
, as given in Equation (10). As an example, let us consider the CG2H40010 device and
. Using (6)–(9), for different implementable values of
,
and
are obtained, as presented in
Table 3.
Figure 2 shows
versus frequency, which provides a notion of the expected bandwidth. It is noticeable that, if
is considered, a bandwidth from almost 0 Hz to 4 GHz is expected for
. As can be seen in
Figure 2, for greater values of
, the bandwidth tends to increase slightly. Therefore,
is considered to be a very good implementable selection in this work.
With the values of
and
, using (6)–(11),
can also be studied for different values of
. This is shown in
Figure 3 for both devices. In
Table 4, the obtained values of
and
versus
are presented.
As the interest of this work is to design an amplifier that covers most of the 5G sub-6-GHz band,
together with CG2H40010 were selected as a suitable option for implementation and case study. However, the complete PA design can also be carried out using CG2H40025, as demonstrated in [
2], where an Input Matching Network (IMN) and stability network were designed for broadband applications for this device. Thus, the PA schematic is shown in
Figure 4. As mentioned above, the substrate RF 35 with
and
was used. As usual, the IMN has been designed including two low impedance shunt stubs and an RC stability network. Two choke inductors in series were implemented as part of the bias-T at the OMN, and the typical 50-ohm terminal load was transformed to
through a four-section Chebyshev transformer. A class AB bias point was adopted with
and
(
). The implemented PA is presented in
Figure 5. In this case, an ad hoc aluminum carrier was used as a heat sink.
The Continuos Wave (CW) characterization results are shown in
Figure 6. As can be noticed, a 4 GHz bandwidth was obtained from very low frequencies up to 4 GHz. Over this band, a drain efficiency between 52% and 70% was obtained, while the output power was from 40 dBm to 42.5 dBm. The transducer gain was always higher than 9 dB over the band. To the best of the authors´ knowledge, these results represent a state-of-the-art single stage PA design.