1. Introduction
In recent times, numerous scientists and researchers have made significant efforts to offer different techniques to change the heat transfer rate owing to its incredible demand in applications in industry and processing. Consequently, the assignment of an enhanced heat transfer rate in common production equipment is a practical and novel advance for detailed assessment of the development of heat capabilities. This is commonly used in heat exchangers, microelectronics, nuclear reactors, bio-medicine, transportation, etc. A group of liquids with superior heat transfer characteristics was proposed by mixing some representative nanomaterials in the base liquids, such as ethylene-glycol, oil, and water. Choi [
1] exploited nanoliquids for the first time by adding a diluted nanoparticle suspension to the base liquids. Khanafer et al. [
2] considered a model to analyze the performance of heat transport of nanoliquids within an enclosure. Ali et al. [
3] reported the experimental results of water based ZnO nanoparticles to change the behavior of the heat transport for the radiator of a car. Ghasemi and Aminossadati [
4] considered the free convective flow through an inclined enclosure occupied with water based CuO nanoliquid. Ahmed and Pop [
5] studied the influence of three distinct nanoparticles on mixed convective flow entrenched in a permeable medium. The characteristics of the drop of pressure and heat transfer ofTiO
2 nanoparticles through a mini-channel heat sink were studied experimentally by Arshad and Ali [
6]. They showed that the thermal behavior of TiO
2 nanoparticles was strongly reliant on the power of heating, but at a lower power of heating, the heat transfer was more effective. Afterwards, numerous researchers [
7,
8,
9,
10,
11,
12,
13,
14] discussed the significance of nanoliquids from different viewpoints. Recently, Saffarian et al. [
15] utilized nanofluid to change the heat transfer (HETR) of a solar collector through a flat surface via the shapes of several flow paths.
Despite the practical insights into nanofluids, there have been few types of nanofluids identified as hybrid nanofluids. Hybrid nanoparticles are developed due to their higher thermo-physical properties, as well as their rheological performance in conjunction with the increasing heat transport properties. Hybrid nanoliquids are developed with nanoparticles created from two separate nanomaterials suspended in a base liquid. This novel class of magnetized heat transport fluids has been studied by numerous researchers to discover solutions to real-life problems and has been broadly exploited in many (HETR) fields, like machine and generator cooling, drug delivery, refrigeration, biomedicine, etc. Sarkar et al. [
16] explored the impact of hybrid nanoliquids by utilizing three distinct base liquids (water, ethylene glycol, and oil). According to their observations, a suitable method of hybridization might disrupt the thermal effectiveness of the hybrid nanoliquids. Furthermore, Sidik et al. [
17] came to a similar conclusion: the thermal properties of the hybrid nanoliquid (HNAN) were superior to the nanoliquid and regular liquid alone. The thermo-physical properties, as well as the synthesis of a hybrid nanoliquid, were explored by Gupta et al. [
18]. The types of host liquids (water, ethylene glycol, and oil) and the types of nanoparticles (metal oxides, metal, metal nitride, and carbon materials), their shape, and size were amongst the features that could affect the thermo-physical properties. Numerical, as well as analytical investigations of hybrid nanofluids were made by Huminic and Huminic [
19]. Shah and Ali [
20] utilized the fabrication technique along with the features of hybrid nanoliquids to investigate solar energy systems. They showed that the (HNANs) played a significant role in the augmentation of power production. A significant assessment of hybrid nanoliquids was presented by Baber et al. [
21]. Recently, Qiu et al. [
22] presented an exceptional review on the thermo-physical properties of nanofluids, as well as hybrid nanofluids.
Fourier’s law illustrates the relation between the temperature gradient and energy flux and is obtained through the correlation of the concentration gradient and mass flux. The Dufour or diffusion-thermo happened due to energy flux, which was posed via a composite gradient. Whereas, the Soret or thermal-diffusion is due to mass fluxes, which are generated by temperature gradient. In another manner, the Soret influence refers to species discrimination rising in an initial homogeneous mixture proposed to a thermal gradient and the Dufour impact submitted to heat-flux generated via a concentration gradient. The influence of the Dufour effect, as well as the Soret effect, in liquids with superior concentration and temperature gradients is highly critical. The physical insight into the liquid’s mechanics is also very critical. Such effects can be calculated in the areas of reactor protection, solar collectors, combustion flames, and building energy conservation. Prasad [
23] discussed the impact of the electric field on the flow from a vertical surface in a non-Darcy medium through the influence of the Dufour and Soret effects. Pal and Mondal [
24] explored the merged magnetic and radiation impacts on viscous mixed convective flow by a nonlinear stretched surface in a non-Darcy permeable medium with the influence of the Dufour and Soret effects. Makinde [
25] studied the Soret effect on magneto hydrodynamic flow across a vertical solid surface with the Dufour number. Chamkha and Rashad [
26] considered the unsteady flow along with the heat and mass transport through a rotated upright cone. They observed that the concentration and thermal fields were additionally influenced by the amount of the Dufour and Soret constraints. Zaib and Shafie [
27] researched the impacts of viscous dissipation and chemical reactions on magneto flow from a stretched radiation sheet. Reddy and Chamkha [
28] surveyed the combination of Dufour numbers and as well as Soret numbers on MHD flow comprised of water-based nanomaterials Al
2O
3 and TiO
2 from a permeable stretched surface by heat generation and absorption. Dzulkifli et al. [
29] discussed the time dependent flow comprised of water-based copper nanomaterial through a stretched/shrinking sheet with the Dufour, slip, and Soret effects, and performed a stability analysis. In recent times, Falodun and Idowu [
30] used the spectral relaxation technique to discuss the Dufour non-Newtonian fluid and Soret numbers from a half-infinite plate.
Secondary or cross flow occurs when the boundary layer portion of the velocity is normal in the free-stream direction. The transverse motion in these flows is presumed to be fully developed. The effect of cross-flow can be seen in many engineering cases, including wind flow phenomena and mechanical aerospace. Jones [
31] demonstrated appealing cross-flow solutions where he noticed the sweep-back effect on the boundary layer. He also reported that the coefficient of lift decreased while the laminar flow stable area increased. Weidman [
32] proposed new results of cross flow for laminar boundary layers. He examined five distinct problems involving cross flow. The forced convection flow along with heat transport containing cross flow were explored by Bhattacharyya and Pop [
33]. Dual results were found for some values of the moving constraint. Haq et al. [
34] scrutinized the impact of viscous dissipation comprised of single, as well as multiple wall carbon nanotubes through the cross flow (CRF) and stream-wise (STWE) directions. Khan et al. [
35] explored the chemical reaction and activation energy of Ti
6Al
4V alloy nanoparticles in the (CRF) and (STWE) directions.
The impacts of the Soret and Dufour effects in the (CRF) and (STWE) direction of nanofluids containing hybrid alloys have not been considered so far. Here, the single-phase model is considered in the presence of these effects. The alloy is a metallic solid or a liquid comprised of the grouping of homogenous and non-homogenous mixtures of two or more nanometer-sized metalloid particles. The alloy is used in many processes like hip joint replacement, surgical implantation, and several biological treatments. Thus, this is the impetus of existing works to analysis the impact of the Soret and Dufour numbers on magneto flow comprised of hybrid AA7075 and Ti6Al4Valloy nanoparticles through a cross flow with nonlinear radiation. The leading PDEs are modified to nonlinear ODEs via a similarity method. The transformed ODE system is then worked out via the built-in solver called bvp4c. The impacts of physical constraints on the flow field are portrayed.
3. Results and Discussion
In this section, we look at the problem formulation where the model consists of highly nonlinear partial differential equations (PDE) [
1,
2,
3,
4,
5], and the exact solution of such a model is quite complicated and seems impossible if the number of parameters involved in the problem is greater than the control of the solution. In our case, the problem was, firstly, tackled numerically through the bvp4c package in MATLAB, where we could exercise the similarity transformations along with the aforementioned PDEs transmuted into nonlinear ODEs [
9,
10,
11,
12] with the related constraint equation [
13]. The pertinent parameters in the problem that were taken to be fixed for computational purposes throughout the process were the following [
37]:
, and
The values of the hybrid nanoparticle volume fraction and the Prandtl number lay in the range
and
, respectively. On the other hand, Oztop and Abu-Nada [
38] investigated the regular viscous fluid when
. The dual solutions (more than one solution) were obtained numerically to analyze the MHD impact on non-linear radiative hybrid nanoliquid flow for the hybrid alloy nanomaterials made of AA7075 and Ti
6Al
4V nanoparticles along with the base fluid, water. The (Sr) and (Du) numbers imposed in the concentration and energy equations were taken, respectively, also travelling along the secondary or stream-wise and cross flow directions. Physically, the stable and unstable solutions, called the upper and lower branch solutions for the corresponding parameters, respectively, were plotted in various graphs. In the entire study, the smaller solid red circles display the critical points at which both branches change their solutions. For computational purposes, the thermo-physical features of the
and
hybrid alloy nanomaterials, along with the host fluid, water, are shown in
Table 2.
Figure 2 is prepared to test the numerical scheme via the accessible graphical results of Bhattacharyya and Pop [
33] in the case of the stream-wise direction in the restrictive case. The assessments confirm a marvelous harmony between the current and available graphical results.
Figure 3 and
Figure 4 display the impact of the
parameter against the shrinking/stretching parameter
for the skin factor coefficients along the stream-wise direction
and the cross flow direction
, while the influences of the same parameter against
on the heat transfer
and the mass transfer
rate are emphasized in
Figure 5 and
Figure 6, respectively. The solution behavior and the critical values of the local skin factor coefficients
, the local heat transfer
, and the mass transfer
against
for the two changed values of the parameter
are exposed in
Figure 3,
Figure 4,
Figure 5 and
Figure 6, respectively. It can be discerned from
Figure 3 that the lower branch solution failed to increase, while the upper solution was boosted with increasing
. It was further noted that the solution for the
was coarser in the shrinking case
than that detected for the case of stretching
.
Figure 4 illustrates the same behavior as in
Figure 3 for the skin coefficient along the cross flow direction
against the moving parameter
as the choice for the numerals of the suction parameter decreases; the upper solution showed a downtrend in motion while the lower solution showed an uptrend. Generally, the skin friction augmented as we increased the parameter
against the moving parameter
due to the inverse relation with the velocity, and by way of a consequence, the momentum boundary layer was thicker and blooming in the first solution and thinner in the second solution, as depicted in
Figure 3 and
Figure 4. The influences of the mass suction parameter
for the two different values against the non-dimensional constant
(say, moving parameter) for the Nusselt and Sherwood numbers were calculated and presented graphically in
Figure 5 and
Figure 6, respectively. It is observed individually for both branches in
Figure 5 that when the values of
decreases against
for the heat transfer profile, both branches of the solutions changed. Moreover, this solution behavior totally changes in
Figure 6 for the rate of mass transfer, which decreases as the value of
decays. In the situation in terms of the plate moving into the origin for
, both the local Nusselt number and local Sherwood number became smaller as compared to the case out of the origin
, but in comparison with
Figure 3 and
Figure 4, this situation is totally different, such as the mass and heat transfer rate computed in terms of
and
were lower for
than examined for
. The variation of the magnetic constraint
for the two different values against the shrinking/stretching parameter
for the skin factor along the stream-wise and the cross flow directions, the rate of heat, and mass transfer are mathematically calculated in terms of the expressions like
,
,
, and
, which are behaviorally emphasized in
Figure 7,
Figure 8,
Figure 9 and
Figure 10, respectively.
The skin factor along the (STW) and (CRF) directions, which was computed by the expression
and
, is portrayed in
Figure 7 and
Figure 8, respectively, where the parameter
is imposed against
, whose critical values are
.
Figure 7 clarifies that as the value of the magnetic parameter decreases, the values of
went down in both branch solutions in the range of
, and then went up for the second branch solution in the range
. In addition, it was predicted clearly in the figure that the values of
for the situation of shrinking were lower than the circumstance of stretching.
Figure 8 displays the behavior of the solution as different from
Figure 7; here, the values of
changed with the decrease of magnetic parameter
.
Figure 9 and
Figure 10 elucidate the influence of
on the rate of heat and mass transfer along the dimensionless constant
, respectively. The critical points along the moving parameter
for the two selected values of
were considered as
for both the mass and heat transfer rate, respectively. Clearly, from the graphical results, the reverse trend of these multiple solutions can be observed in both of these figures. In a more compact way, it was interpreted that for the finer choices of
, the first branch solution showed a declining behavior, whilst for the second branch solution, an uptrend behavior was perceived. In addition, such graphs exemplified that the erratic engineering features like mass and heat transfer rate were quite fine for the lower branch as compared to the upper branch solution.
Figure 11,
Figure 12,
Figure 13 and
Figure 14 illustrate the effect of the Dufour and Soret numbers on the heat and mass transfer rate against the moving parameter
, respectively. Furthermore,
Figure 11 displays the Dufour effect of the two different values on
against
. The value of the Dufour parameter increases, and as a result, both branches of the solutions showed a decaying behavior, while the reverse behavior was detected for
as the Dufour parameter uplifts, highlighted in
Figure 12. The influences of the Soret
parameter against
for the Nusselt and Sherwood numbers are investigated in
Figure 13 and
Figure 14, respectively. The local heat transfer was growing in both branch solutions along parameter
as the Soret number upsurges, while the contradictory behavior was noticed for the mass transfer rate.
The influence of the magnetic field parameter for the three different selected values in terms of computing the velocities in the stream-wise direction
and the cross flow direction
is highlighted graphically in
Figure 15 and
Figure 16. This showed that the first solution, which is also called the lower branch solution, decreased in both aforementioned graphs and the second solution, called the upper branch, was growing as the values of
changed. Physically, one could notice this obvious behavior due to the change of the magnetic parameter creating a large Lorentz (drag) force, which retarded the motion of the fluids significantly, and thus, the profiles in terms of the velocity and the boundary layer thickness decelerated as the magnetic parameter increased.
Figure 17 and
Figure 18 display the flow trend of the fields such as temperature
and concentration
for the numerous values of
, respectively. It is discerned from
Figure 17 that by increasing
, the behavior of the solution for the temperature increased in the upper branch. Physically, the strong Lorentz force dropped to slow down the fluid flow, which, accordingly, caused extra friction amid the fluid molecules. Thus, additional heat was generated, therefore increasing the temperature of fluid. However, this trend totally changed in the behavior of the second branch solution; the temperature profile declined with growing
. A similar behavior is noticed in
Figure 18 as in
Figure 17, which shows that the influence of the magnetic field constraint on the concentration profile of the hybrid nanofluid was increased in the first branch solution, while it decreased in the second branch solution.
Figure 19 shows the influence of the temperature ratio parameter
on the temperature profile. It is observed clearly from its graphical results that both branch solutions became higher for the three different ascending values of
.
Figure 20 shows that the first solution decreased for the temperature profile
, and the second solution increased as the radiation parameter
became successively larger. A greater amount of radiation implied the dominance of conduction, and thus, the thermal boundary layer thickness diminished. The effect of the Schmidt parameter
on
is depicted in
Figure 21. Moreover, its shows that the behavior of the multiple or dual solution and the concentration of the boundary layer decelerated in both the branches of outcomes due to changing the values of
. The Schmidt number exemplified the ratio of kinematic viscosity to molecular mass diffusivity for the enhancement of
Sc, which differed from a decline in mass diffusivity in the system, and which consequently lowered the concentration profile.
Figure 22,
Figure 23,
Figure 24 and
Figure 25 show the impacts of the hybrid nanomaterial parameters
on the velocity in the stream-wise direction
the velocity in the cross flow direction
temperature distribution
, and the concentration profile
, respectively. Further, it was observed that when the values of the hybrid alloy nanomaterials
increase, the first solution decreases, while the lower solution increases in the velocities profile, and their graphical behavior is captured in
Figure 22 and
Figure 23, respectively. This is apparent from the reality that greater amounts of
communicate to intensify the hybrid nanofluids thermal conductivity, which inspires the diffusion of heat so that the heat impulsively disperses near the surface.
Figure 24 and
Figure 25 present the importance of the hybrid alloy nanomaterials
on the temperature and concentration profiles. More precisely, it is noted that the temperature and the nanofluid concentration is enhanced in both branches of the solution (lower and upper) when
upsurge. Since, the large amounts of
generate a great quantity of energy during the flow connected with the uneven progress of the ultrafine materials, they, hence, produce a substantial improvement in the rate of heat and mass transfer, which consequently augments the temperature and the concentration.