Effect of Thermomechanical Cycling on Martensitic Transformation and Shape Memory Effect in 304 Austenitic Steel
Abstract
:1. Introduction
2. Materials and Methods
3. Results
3.1. Shape Memory Effect
3.2. Microstructures and Mechanical Behavior
4. Discussion
4.1. Improving SME Related to Stress-Induced ε Martensite by Thermomechanical Cycling
4.2. Promoting Effect of Thermomechanical Cycling on Stress-Induced γ→ε Transformation
4.3. Suppressing Effect of Thermomechanical Cycling on Stress-Induced ε→α’ Transformation
5. Conclusions
Author Contributions
Funding
Conflicts of Interest
References
- Lo, K.H.; Shek, C.H.; Lai, J.K.L. Recent developments in stainless steels. Mater. Sci. Eng. R 2009, 65, 39–104. [Google Scholar] [CrossRef]
- Unnikrishnan, R.; SatishIdury, K.S.N.; Ismail, T.P.; Bhadauria, A.; Shekhawat, S.K.; Khatirkar, R.K.; Sapate, S.G. Effect of heat input on the microstructure, residual stresses and corrosion resistance of 304L austenitic stainless steel weldments. Mater. Charact. 2014, 93, 10–23. [Google Scholar] [CrossRef]
- Mangonon, P.L., Jr.; Thomas, G. Martensite phases in 340 stainless steel. Metall Trans. 1970, 1, 1577–1586. [Google Scholar] [CrossRef]
- Enami, K.; Nenno, S.; Minato, Y. Shape memory effect associated with the martensite transformation in 304 type stainless steel. Scr. Metall. 1971, 5, 663–667. [Google Scholar] [CrossRef]
- Enami, K.; Nenno, S.; Minato, Y. Direct observations of the reverse transformation of ε martensite in type 304 stainless steel. Trans. JIM 1977, 18, 435–442. [Google Scholar] [CrossRef] [Green Version]
- Sato, A.; Chishima, E.; Soma, K.; Mori, T. Shape memory effect in γ→ε transformation in Fe-30Mn-1Si alloy single crystals. Acta Metall. 1982, 30, 1177–1183. [Google Scholar] [CrossRef]
- Wen, Y.H.; Peng, H.B.; Raabe, D.; Gutiérrez-Urrutia, I.; Chen, J.; Du, Y.Y. Large recovery strain in Fe-Mn-Si-based shape memory steels obtained by engineering annealing twin boundaries. Nat. Commun. 2014, 5, 4964. [Google Scholar] [CrossRef] [PubMed] [Green Version]
- Kajiwara, S. Characteristic features of shape memory effect and related transformation behavior in Fe-based alloys. Mater. Sci. Eng. A 1999, 273, 67–88. [Google Scholar] [CrossRef]
- Peng, H.B.; Chen, J.; Wang, Y.N.; Wen, Y.H. Key factors achieving large recovery strains in polycrystalline Fe-Mn-Si-based shape memory alloys: A review. Adv. Eng. Mater. 2018, 1700741, 1–18. [Google Scholar] [CrossRef]
- Tomota, Y.; Nakagawara, W.; Tsuzaki, K.; Maki, T. Reversion of stress-induced ε martensite and two-way shape memory in Fe-24Mn and Fe-24Mn-6Si alloys. Scr. Metall. Mater. 1992, 26, 1571–1574. [Google Scholar] [CrossRef]
- Peng, H.B.; Wang, G.X.; Wang, S.L.; Chen, J.; MacLaren, I.; Wen, Y.H. Key criterion for achieving giant recovery strains in polycrystalline Fe-Mn-Si based shape memory alloys. Mater. Sci. Eng. A 2018, 712, 37–49. [Google Scholar] [CrossRef] [Green Version]
- Peng, H.B.; Wen, Y.H.; Liu, G.; Wang, C.P.; Li, N. A role of α′ martensite introduced by thermo-mechanical treatment in improving shape memory effect of an Fe-Mn-Si-Cr-Ni alloy. Adv. Eng. Mater. 2011, 13, 388–394. [Google Scholar] [CrossRef]
- Reyhani, M.M.; McCormick, P.G. Effect of thermomechanical cycling in an Fe-Mn-Si-Cr-Ni shape memory alloy. Scr. Metall. Mater. 1994, 31, 875–878. [Google Scholar] [CrossRef]
- Stanford, N.; Dunne, D.P. Thermo-mechanical processing and the shape memory effect in an Fe-Mn-Si-based shape memory alloy. Mater. Sci. Eng. A 2006, 422, 352–359. [Google Scholar] [CrossRef]
- Druker, A.; Baruj, A.; Malarría, J. Effect of rolling conditions on the structure and shape memory properties of Fe-Mn-Si alloys. Mater. Charact. 2010, 61, 603–612. [Google Scholar] [CrossRef]
- Mangonon, P.L.; Thomas, G. Structure and properties of thermal-mechanically treated 304 stainless steel. Metall. Trans. 1970, 1, 1587–1594. [Google Scholar] [CrossRef] [Green Version]
- Chen, J.; Peng, H.B.; Wang, S.L.; Du, Y.Y.; Wen, Y.H. Remarkable improvement of shape memory effect in austenitic stainless steel by thermo-mechanical training. Adv. Eng. Mater. 2015, 17, 330–333. [Google Scholar] [CrossRef]
- Watanabe, Y.; Miyazaki, E.; Okada, H. Smart materials-fundamentals and applications. Enhanced mechanical properties of Fe-Mn-Si-Cr shape memory fiber/plaster smart composite. Mater. Trans. 2002, 43, 974–983. [Google Scholar] [CrossRef] [Green Version]
- Kaoumi, D.; Liu, J. Deformation induced martensitic transformation in 304 austenitic stainless steel: In-situ vs. ex-situ transmission electron microscopy characterization. Mater. Sci. Eng. A 2018, 715, 73–82. [Google Scholar] [CrossRef]
- Liu, J.; Kaoumi, D. Use of in-situ TEM to characterize the deformation-induced martensitic transformation in 304 stainless steel at cryogenic temperature. Mater. Charact. 2018, 136, 331–336. [Google Scholar] [CrossRef]
- Li, N.; Wang, Y.D.; Liu, W.J.; An, Z.N.; Liu, J.P.; Su, R.; Li, J.; Liaw, P.K. In situ X-ray microdiffraction study of deformation-induced phase transformation in 304 austenitic stainless steel. Acta Metall. 2014, 64, 12–23. [Google Scholar] [CrossRef]
- Zheng, C.S.; Liu, C.J.; Ren, M.H.; Jiang, H.; Li, L.F. Microstructure and mechanical behavior of an AISI 304 austenitic stainless steel prepared by cold-or cryogenic-rolling and annealing. Mater. Sci. Eng. A 2018, 724, 260–268. [Google Scholar] [CrossRef]
- Talonen, J.; Hänninen, H. Formation of shear bands and strain-induced martensite during plastic deformation of metastable austenitic stainless steels. Acta Mater. 2007, 55, 6108–6118. [Google Scholar] [CrossRef]
- Stanford, N.; Dunne, D.P. Effect of NbC and TiC precipitation on shape memory in an iron-based alloy. J. Mater. Sci. 2006, 41, 4883–4891. [Google Scholar] [CrossRef]
- Wang, Y.N.; Chen, J.; Peng, H.B.; Wen, Y.H. Shape memory effect induced by stress-induced α′ martensite in a metastable Fe-Cr-Ni austenitic stainless steel. Acta Metall. Sin. (Engl. Lett.) 2017, 30, 513–520. [Google Scholar] [CrossRef] [Green Version]
- Kruml, T.; Polák, J.; Degallaix, S. Microstructure in 316LN stainless steel fatigued at low temperature. Mater. Sci. Eng. A 2000, 293, 275–280. [Google Scholar] [CrossRef]
- Lee, W.S.; Lin, C.F. The morphologies and characteristics of impact-induced martensite in 304L stainless steel. Scr. Mater. 2000, 43, 777–782. [Google Scholar] [CrossRef]
- Sato, K.; Ichinose, M.; Hirotsu, Y.; Inoue, Y. Effects of deformation induced phase transformation and twinning on the mechanical properties of austenitic Fe-Mn-Al alloys. ISIJ Int. 1989, 20, 868–877. [Google Scholar] [CrossRef]
- Dai, Q.X.; Cheng, X.N.; Luo, X.M.; Zhao, Y.T. Structural parameters of the martensite transformation for austenitic steels. Mater. Charact. 2002, 49, 367–371. [Google Scholar] [CrossRef]
© 2020 by the authors. Licensee MDPI, Basel, Switzerland. This article is an open access article distributed under the terms and conditions of the Creative Commons Attribution (CC BY) license (http://creativecommons.org/licenses/by/4.0/).
Share and Cite
Chen, J.; Zhang, Y.; Ge, J.; Peng, H.; Huang, S.; Yang, Q.; Wen, Y. Effect of Thermomechanical Cycling on Martensitic Transformation and Shape Memory Effect in 304 Austenitic Steel. Metals 2020, 10, 901. https://doi.org/10.3390/met10070901
Chen J, Zhang Y, Ge J, Peng H, Huang S, Yang Q, Wen Y. Effect of Thermomechanical Cycling on Martensitic Transformation and Shape Memory Effect in 304 Austenitic Steel. Metals. 2020; 10(7):901. https://doi.org/10.3390/met10070901
Chicago/Turabian StyleChen, Jie, Yonghao Zhang, Jiqiang Ge, Huabei Peng, Shuke Huang, Qin Yang, and Yuhua Wen. 2020. "Effect of Thermomechanical Cycling on Martensitic Transformation and Shape Memory Effect in 304 Austenitic Steel" Metals 10, no. 7: 901. https://doi.org/10.3390/met10070901