1. Introduction
As the exploitation of offshore oil and gas and renewable energies has gradually stepped into deeper waters, anchor foundations are required to moor the floating facilities. As shown in
Figure 1a, the floating facility and the anchor foundation are connected through mooring chains; the chain profile in soil is usually a reverse catenary-shaped due to chain–soil interaction under the tension load. The chain is subject to the normal and tangential resistances applied by soil, with tension at the padeye and along the chain varying by time and depth. The chain–soil interaction leads to variations in the magnitude and inclination of the tension load at the padeye, which determines the potential mobilized anchor capacity [
1,
2,
3,
4,
5,
6].
The analysis of the interaction between the chain and soil mainly estimates soil resistances in the normal and tangential directions of the chain segment, noted as
Q and
F, respectively, in
Figure 1a. The mooring chains used in practical applications can be categorized as those with or without the stud. The length of each pair of stud-link chains is 8
d where
d is the nominal diameter of the chain; the length of each pair of link chains without a stud is 6
d (see
Figure 1b). To facilitate designs, the chain was usually simplified as a cylindrical line which was discretized with a number of curvilinear segments. For each chain segment, the tensions at both ends were in balance with the normal and tangential resistances applied by neighboring soil. By solving the equilibrium equations for these forces, the chain profile in soil can be predicted [
2,
7,
8]. Therefore, it is vital to estimate the normal and tangential resistances appropriately.
In their previous analysis, Neubecker and Randolph assumed that the conventional friction ratio,
F/
Q, was constant to determine the chain friction coefficient, which was taken as 0.4–0.6 [
9]. However, several recent investigations indicate great variations in friction mobilization for the chain segments [
10]; therefore, the assumption of a constant friction ratio may not be on the conservative side for routine designs. An alternative option is to develop an interaction envelope to capture the friction mobilization along the chain profile. The envelopes have been employed in the designs of various offshore footings, such as spudcan footings [
11,
12] and suction anchors [
13,
14,
15].
The chain was simplified as a series of cylindrical segments with an equivalent diameter derived from the effective area in bearing or in shearing in most previous analytical and numerical analyses. Therefore, the influence of the chain’s actual geometry on capacities was essentially ignored. The actual physical shape of the chain is rather complicated; the typical shape and size of the studless chain is shown in
Figure 1b. The soil flow mechanism around the physical segment may be different from that caused by the motion of a cylindrical segment.
This study accounts for the actual shape of the chain and analyzes the difference from the simplified solution. The studless chain segment’s dynamics within clayey soil were simulated using a large deformation finite element approach, to obtain its uniaxial capacities and yield envelope in the Q-F load space. The results are compared to previous studies that simplified the chain segment as a cylinder, to highlight the need to also consider the chain geometry. Additionally, the influence of the chain roughness on the capacities is investigated. The yield envelope obtained is capable of predicting the magnitude and direction of tension at the padeye more accurately; energy firms can then use these data to create more economical and reasonable designs for anchoring systems.
3. Uniaxial Capacities
In the existing analytical solutions, the uniaxial resistances in the normal and tangential directions,
Q and
F, were determined by [
9]:
where bearing capacity factor
Nc is suggested increasing from 5.1 at the seabed to 7.6 at a chain depth of 6
d for the plane strain failure; and
En and
Et are multipliers to give the effective widths in the normal and tangential directions, respectively.
En and
Et were suggested as 2.5 and 8.0 by Degenkamp and Dutta; their view was adopted by later studies, such as Neubecker and Randolph [
9] and Li et al. [
4]. Equations (2) and (3) were used in terms of cylindrical chain segments, and the actual shape of the chain was represented by the multipliers
En and
Et.
In the LDFE simulations, the chain segments with actual geometry are displaced in the normal and tangential directions such that the ultimate normal and frictional capacities (
Q and
F) could be obtained for comparison with the analytical solutions. Here, the normalized normal resistance,
Nb, is defined for convenience of discussions:
where
A is the projected area of the chain segment with actual geometry, and the normal capacity per unit length
Q is derived from the numerical results.
Nb is more suitable to express the normal capacity factor of the chain segment.
The roughness of chain–soil interaction is accounted for by varying values of 0.3, 0.5 and 1 in the finite element model. The LDFE result of normal resistance is demonstrated in
Figure 5, and more solutions of structural elements with similar geometries are plotted as well. As shown in
Figure 5, the normalized normal resistance is increased rapidly with displacement at the early stage of the loading, followed by gradual enhancement until an ultimate value was reached. The ultimate values of
Nb, defined as
Nb,ult, were estimated as 11.8, 12.2 and 12.8 for
α = 0.3, 0.5 and 1, respectively. As shown in
Figure 5, the divergence of
Nb,ult induced by the chain roughness is insignificant, at less than 8.5% between the cases with
α = 0.3 and 1. Sun et al. simulated simplified cylinder chain segments using a LDFE approach termed “Coupled Eulerian-Lagrangian” [
10]. They proposed
Nb,ult = 14.0 with
α = 0.5, which is 14.8% larger than our results for chain segments with actual geometry. When the chain segment moved, part of the soil embedded in the holes of the chain segment moved together with the chain; therefore, the soil flow mechanism may be similar to those of the deep foundations addressed below. Randolph and Houlsby suggested that the capacity factor of a circle pile in deep soil is ranged between 9.14 for smooth ones and 11.94 for rough ones, based on the upper-bound limit analyses [
19]. The upper-bound solution by Merifield et al. indicated a capacity factor of 11.4 for an ultrathin rough strip plate buried deeply [
20]. Wang et al. proposed that the rough deep rectangular plate with an aspect ratio of 2 was with
Nb,ult = 13.3 [
17], which is close to 12.8 for the rough chain segment in
Figure 5. The soil incremental displacements around the chain segment were demonstrated in
Figure 6, and the incremental displacement of the chain in each step was 0.001 m. The soil displacements above and underneath the segment are symmetric since the chain was assumed to be buried deeply. It was observed as well that the soil displacements around the left and right ends of the chain segments were relatively small. Therefore, for the chain segment subjected to normal loading, the soil flow mechanism mobilized was similar to that around a plate with the same projected plan. The projected plan of the chain segment in
Figure 2 can be simplified roughly as a rectangle with length of 6
d and width of 3.6
d. That explains why the
Nb,ult values of chain segment and rectangular plate are close to each other. It is worth noting again that the normal resistances discussed above are for the structural elements embedded deeply. The chain segments buried shallowly are beyond the concern of this paper.
Based on the values of
Nb shown in
Figure 5, the multiplier for the effective width in the normal direction
En can be obtained by substituting Equation (4) into Equation (2). The expression becomes:
Equation (5) suggests that the chain roughness has no obvious effect on the value of
En, at least for the chain simplified as cylindrical. According to Equation (5),
En is function of the area per unit length and the nominal diameter of the chain segment; thus, it is a constant value for a particular geometry of the chain. It is not clear if Equation (5) is suitable for the chain segment with actual geometry, so the LDFE results of
En are replotted in
Figure 7a. The numerical values of
En against
α = 0.3, 0.5 and 1 were the same as 2.3, indicating that the influence of the chain roughness was minimal. Degenkamp and Dutta conducted several model tests for chain segments with actual geometry [
21]. The undrained shear strength of clay used in their tests was measured as 4.52 kPa, with a deviation of about 0.57 kPa. They found that
En was ranged between 2 and 3, and their recommended value of 2.5 is close to that indicated by the LDFE analyses.
The model tests by Degenkamp and Dutta provided a relatively large range of
Et = 5.5–12.0, and
Et = 8.0 was recommended [
21]. Most recently, Sampa et al. measured the friction along the chain in their model tests, and suggesting a narrow range of
Et = 8.4–10.8 [
22]. Sampa et al. proposed that the
Et value tends to decrease in tandem with an increase in the nominal diameter
d. The LDFE load–displacement curves for tangential displacements of segments are demonstrated in
Figure 7b. All three ultimate resistances are reached at a displacement of around 0.04
d. The
Et values deduced from the LDFE analyses are 8.2, 8.9 and 9.7 as
α = 0.3, 0.5 and 1.0, respectively, which are in agreement with the values recommended by Degenkamp and Dutta [
21], and Sampa et al. [
22]. In contrast to the phenomenon observed for
En (see
Figure 7a), the value of
Et is enhanced with the chain roughness, with a difference of 18.3% between
α = 0.3 and 1. Similar to Equation (4), the normalized tangential resistance
Ns is defined as
The ultimate value of
Ns is defined as
Ns,ult. The
Ns,ult values range between 3.6 and 4.3 in
Figure 7b; these values are moderately lower than 4.7 from the numerical simulations in terms of the simplified cylindrical chain [
10].
4. Yield Envelope for Chain under Combined Loading
Although the ultimate uniaxial capacities in the normal and tangential have been estimated above, the capacities of the chain segment subjected to combined loading remain unknown. The tangential resistance may be impaired by the appearance of normal loading and vice versa. A potential solution for tackling the problem of combined loading is to develop an interaction diagram of the yield envelope. The forces of components outside of the yield envelope are not represented on such a diagram.
The probe test and swipe test are the two methods most commonly used in numerical and experimental explorations to obtain the yield envelope. The envelopes established by these methods may be close for a few foundation types; however, non-negligible divergence between the envelopes may appear for a given foundation, as found in [
23] and [
24]. Therefore, both the swipe and probe tests are employed here, to quantify the potential error. The probe test is featured with fixed-ratios of displacement, i.e., the chain segment is loaded with the tangential and normal displacement increments, d
u and d
w, applied proportionally. As suggested by Tan [
25], the swipe test is implemented by the swipe-loading path. It consists of two steps: the chain segment is moved in the normal direction until the ultimate normal resistance is achieved, and; a tangential displacement is subsequently imposed while the normal displacement remains zero. The envelope is obtained by connecting these force components.
The LDFE curves based on the probe tests and the yield envelope established are demonstrated in
Figure 8. For chain segments with roughness of 0.3, a total number of nine loading paths with different ratios of displacement are plotted in
Figure 8a. At the early phase of the loading, the loading path is controlled by the elastic stiffnesses, followed by the elasto-plastic response. The final phases of the loading paths, which have a variety of d
u/d
w values, are used to shape the envelope. For the loading paths with low d
u/d
w values, such as d
u/d
w ranged between 0.1 and 0.5 in
Figure 8a, the curves end at the envelope. If the d
u/d
w value range is large, such as d
u/d
w = 2–10, the loading path reaches the yield envelope rapidly; the curve then moves along the envelope. Similar phenomena are observed in the LDFE cases with
α = 0.5 and 1 in
Figure 8b,c.
The yield envelopes demonstrated in
Figure 8 can be expressed in the form of an ellipse
where the exponents
m and
n are to denote the shape of the envelope and they are determined by fitting the LDFE results in
Figure 8. The
Nb,ult values of 11.8, 12.2 and 12.8 are estimated from data in
Figure 5 for the chain roughness, with
α = 0.3, 0.5 and 1.0, respectively, while
Ns,ult = 3.6, 3.9 and 4.3, as demonstrated in
Figure 7b. The exponents are selected as
m = 2.1 and
n = 2.3 for all chain roughness values. It indicates that the shape of the yield envelope is nearly independent of the chain roughness, although
Nb,ult and
Ns,ult are functions of the roughness. As shown in
Figure 8, Equation (7) with the values stated above can accurately depict the final phases of the loading paths. As the normal and tangential resistances are varied along the yield envelope, the friction ratio
F/
Q could not be a constant value, even though the assumption of constant ratio was recognized widely in the previous studies [
9].
The swipe tests are employed as well to derive the yield envelopes. The envelopes by the swipe test and probe test are compared in
Figure 9, in terms of the segment with
α = 0.5. The two envelopes in the
F-
Q plane achieve reasonable consistency. Again, the robustness and accuracy of the LDFE simulations are validated. The LDFE results based on the probe tests are chosen to establish the expression of the yield envelope (i.e., Equation (7)).
The envelopes deduced from Equation (7), with
α = 0.3, 0.5 and 1, are compared with that by Sun et al. [
10] in
Figure 9. Sun et al. proposed an envelope with the chain segment simplified as a cylinder with
α = 0.5. Their envelope is moderately larger than those with actual chain geometry. For example, as
α = 0.5 and
Nb = 4,
Ns of the segment with actual geometry is 16% lower than that of the cylindrical segment; the difference then becomes 16.8% as
Nb = 10.
5. Conclusions
This paper presents the numerical investigations of chain capacities in clayey soil using a large deformation finite element approach and the actual chain geometry. The numerical model is calibrated by investigating the uniaxial normal and tangential capacities of chain segments, followed by the yield envelope developed for the segments under combined loading.
The ultimate normalized normal resistance is in the range of 11.8–12.8, which is close to the recommendations for the deep foundation with similar projected plan, such as a rectangular plate. However, this range is considerably lower than the value based on the simplified cylindrical chain. A similar phenomenon is observed for the ultimate value of normalized tangential resistance. The resulting multipliers for effective widths, En and Et, agree with the existing model tests. The yield envelopes for the chain segments under combined loading are established using the probe and swipe tests, and both tests provide yield envelopes with similar shapes. A general form of ellipse expression is proposed to capture all the yield envelopes with different values of the chain roughness. As the chain roughness increases, the uniaxial tangential capacities and yield envelope are increased gradually. To account for the actual geometry of the chain segment, the yield envelope obtained is located against the simplified cylindrical chain.
However, this paper is mainly focused on the ultimate resistance for the chain segment under combined loading, and mobilizations of the soil resistances in normal and tangential directions. The problem of chain cutting through soil can be investigated by developing a global chain–soil interaction model based on the conclusions of this paper.