Next Article in Journal
Numerical Approach to a Nonlocal Advection-Reaction-Diffusion Model of Cartilage Pattern Formation
Previous Article in Journal
The Complementary q-Lidstone Interpolating Polynomials and Applications
 
 
Font Type:
Arial Georgia Verdana
Font Size:
Aa Aa Aa
Line Spacing:
Column Width:
Background:
Article

On a Laminated Timoshenko Beam with Nonlinear Structural Damping

by
Tijani A. Apalara
1,*,†,
Aminu M. Nass
2,† and
Hamdan Al Sulaimani
1,†
1
Department of Mathematics, University of Hafr Al-Batin (UHB), Hafr Al-Batin 31991, Saudi Arabia
2
Department of Actuarial Science, Federal University Dutse (FUD), Dutse P.M.B. 7156 Jigawa State, Nigeria
*
Author to whom correspondence should be addressed.
These authors contributed equally to this work.
Math. Comput. Appl. 2020, 25(2), 35; https://doi.org/10.3390/mca25020035
Submission received: 19 May 2020 / Revised: 13 June 2020 / Accepted: 17 June 2020 / Published: 19 June 2020
(This article belongs to the Section Natural Sciences)

Abstract

:
In the present work, we study a one-dimensional laminated Timoshenko beam with a single nonlinear structural damping due to interfacial slip. We use the multiplier method and some properties of convex functions to establish an explicit and general decay result. Interestingly, the result is established without any additional internal or boundary damping term and without imposing any restrictive growth assumption on the nonlinear term, provided the wave speeds of the first equations of the system are equal.

1. Introduction

In the late 1990s, a model for structure of two identical beams with uniform thickness was developed by Hansen and Spies [1]. This model is called a laminated Timoshenko beam and is given by
ρ w t t + G ( ψ w x ) x = 0 , I ρ ( 3 s t t ψ t t ) D ( 3 s x x ψ x x ) G ( ψ w x ) = 0 , 3 I ρ s t t 3 D s x x + 3 G ( ψ w x ) + 4 γ s + 4 β s t = 0 ,
where the terms w , ψ , s represent the transverse displacement, the rotation angle, and the amount of slip along the interface, respectively. The positive parameters ρ , G , I ρ , D , γ , and β are known as the density, shear stiffness, mass moment of inertia, flexural rigidity, adhesive stiffness, and adhesive (structural) damping at the interface, respectively. It is very close to the well-known classical Timoshenko system because the equations of motion modeling the system are derived under the assumption of the Timoshenko beam theory. In addition, the third equation (which contains the structural damping s t ) is coupled with the first two describing the dynamic of the interfacial slip. These structures are highly important and have gained massive popularity in engineering fields.
Stabilization of the system with various internal or boundary damping mechanisms has been the subject of research over the years. Specifically, an increasing interest has been developed to determine the asymptotic behavior of the system which are paramount in classifying the empirical observations of the engineers.
Let us start with the boundary stabilization. To the best of our knowledge, the first known result in this case was established by Wang et al. [2]. They considered (1) together with some mixed homogeneous boundary conditions, introduced a change of variable ξ = 3 s ψ , and thereby established an exponential decay result provided ρ G I ρ D . Tatar [3] established the same exponential result of [2] provided ρ G < I ρ . Mustafa [4] also obtained a similar result under the condition of equality between velocities of wave propagation, that is
ρ G = I ρ D .
We refer the reader to [5,6,7,8] and the references cited therein for some other results on boundary stabilization.
For viscoelastic damping (memory term), we mention the work of Lo and Tatar [9]. They considered system (1) with viscoelastic damping of the form 0 t g ( t r ) ( 3 s x x ψ x x ) ( r ) d r on the second equation and proved that the resulting system is exponentially stable provided the relaxation function g decays exponentially and (2) is satisfied, in addition to some conditions on the parameter G. Mustafa [10] improved the result in [9] by adopting minimal and general conditions on g. Consequently, he established explicit energy decay result. Some other results can be found in [11,12,13,14,15] and the references cited therein.
The thermal effect (classical or second sound) is another way of stabilizing the laminated beams. Apalara in [16] proved that the heat effect is sufficiently strong enough to stabilize laminated beams exponentially without any other damping term, provided (2) holds. A similar result was obtained by Apalara [17] for the second sound in the presence of a structural damping term.
For frictional damping on the three equations, we mention the work of Raposo [18]. Recently, Alves et al. [19] established an exponential decay for the laminated system with only structural damping, provided the wave velocities are equal. It is imperative to mention that when s 0 , then the laminated beams reduced to the standard Timoshenko system, see [17,18]. We refer the reader to [19,20,21,22,23,24] for some other varios forms of damping mechanisms
In this paper, we consider a laminated Timoshenko beam with only a single source of dissipation in the form of a nonlinear interfacial slip
ρ w t t + G ( ψ w x ) x = 0 in ( 0 , 1 ) × ( 0 , ) , I ρ ( 3 s t t ψ t t ) D ( 3 s x x ψ x x ) G ( ψ w x ) = 0 in ( 0 , 1 ) × ( 0 , ) , 3 I ρ s t t 3 D s x x + 3 G ( ψ w x ) + 4 γ s + 4 β h ( s t ) = 0 in ( 0 , 1 ) × ( 0 , ) , w ( x , 0 ) = w 0 , w t ( x , 0 ) = w 1 , ψ ( x , 0 ) = ψ 0 , ψ t ( x , 0 ) = ψ 1 , in ( 0 , 1 ) , s ( x , 0 ) = s 0 , s t ( x , 0 ) = s 1 , in ( 0 , 1 ) , w x ( 0 , t ) = ψ ( 0 , t ) = s ( 0 , t ) = w ( 1 , t ) = ψ x ( 1 , t ) = s x ( 1 , t ) = 0 , in ( 0 , )
and discuss the general decay of the energy of the system under suitable assumption on the nonlinear term and coefficients of wave propagation speed. On the nonlinear term h, we assume, as in Lasiecka and Tataru [25], that it satisfies the following hypotheses:
(A1)
h : R R is a non-decreasing C 0 -function such that there exist positive constants c 1 , c 2 , ϵ , and a strictly increasing function H C 1 ( [ 0 , + ) ) , with H ( 0 ) = 0 , and H is linear or strictly convex C 2 -function on ( 0 , ϵ ] such that
y 2 + h 2 ( y ) H 1 ( y h ( y ) ) for all | y | ϵ , c 1 | y | | h ( y ) | c 2 | y | for all | y | ϵ .
Remark 1.
  • Hypothesis (A1) implies that y h ( y ) > 0 , for all y 0 .
  • Lasiecka and Tataru in [25] used the monotonicity and continuity of h to establish the existence of H as defined in (A1).
For completeness purpose, we introduce the following spaces
H a 1 = { ψ : ψ H 1 ( 0 , 1 ) : ψ ( 0 ) = 0 } , H b 1 = { ψ : ψ H 1 ( 0 , 1 ) : ψ ( 1 ) = 0 } , H b 2 ( 0 , 1 ) = { ψ H 2 ( 0 , 1 ) : ψ x ( 0 ) = 0 } , H a 2 ( 0 , 1 ) = { ψ H 2 ( 0 , 1 ) : ψ x ( 1 ) = 0 }
and state, without proof, the following existence and regularity result:
Proposition 1.
For Φ = ( w , u , z , v , s , y ) T ; u = w t , z = 3 s ψ , v = z t , y = s t , and assume that (A1) is satisfied. Then for all Φ 0 H b 1 ( 0 , 1 ) × L 2 ( 0 , 1 ) × H a 1 ( 0 , 1 ) × L 2 ( 0 , 1 ) 2 , the system (1) has a unique global (weak) solution
w C ( R + ; H b 1 ( 0 , 1 ) ) C 1 ( R + ; L 2 ( 0 , 1 ) ) , z , s C ( R + ; H a 1 ( 0 , 1 ) ) C 1 ( R + ; L 2 ( 0 , 1 ) ) .
Moreover, if
Φ 0 H b 2 ( 0 , 1 ) H b 1 ( 0 , 1 ) × H b 1 ( 0 , 1 ) × H a 2 ( 0 , 1 ) H a 1 ( 0 , 1 ) × H a 1 ( 0 , 1 ) 2 ,
then the solution satisfies
w L ( R + ; H b 2 ( 0 , 1 ) H b 1 ( 0 , 1 ) ) W 1 , ( R + ; H b 1 ( 0 , 1 ) ) W 2 , ( R + ; L 2 ( 0 , 1 ) ) z , s L ( R + ; H a 2 ( 0 , 1 ) H a 1 ( 0 , 1 ) ) W 1 , ( R + ; H a 1 ( 0 , 1 ) ) W 2 , ( R + ; L 2 ( 0 , 1 ) ) .
Remark 2.
This result can be proved using standard arguments such as nonlinear semi-group method (see [26]) or the Faedo–Galerkin method (see [27]).
The rest of the paper is organized as follows. In Section 2, we state and prove some essential technical lemmas. We give our stability result in Section 3. We use c throughout this paper to denote a generic positive constant, which may be different from line to line (even in the same line). Our work gives an adequate answer to the possibility of stabilizing a Timoshenko Laminated beam with single non-linear damping present only in the third equation with some appropriate conditions.

2. Technical Lemmas

This section is devoted to the statements and proofs of some essential technical lemmas, which are highly influential in proving our main result.
Lemma 1.
Let ( w , ψ , s ) be the solution of system (3) and assume (A1) holds. Then the energy functional defined by
E ( t ) = 1 2 0 1 ρ w t 2 + I ρ ( 3 s t ψ t ) 2 + D ( 3 s x ψ x ) 2 + G ( ψ w x ) 2 + 3 I ρ s t 2 + 3 D s x 2 + 4 γ s 2 d x
satisfies
E ( t ) = 4 β 0 1 s t h ( s t ) d x 0 .
Proof
By multiplying (3) 1 by w t , (3) 2 by ( 3 s t ψ t ) , and (3) 3 by s t , then integrating over ( 0 , 1 ) , using integration by parts and the boundary conditions, we obtain
ρ 2 d d t 0 1 w t 2 d x = G 0 1 ( ψ w x ) w t x d x ,
I ρ 2 d d t 0 1 ( 3 s t ψ t ) 2 d x + D 2 d d t 0 1 ( 3 s x ψ x ) 2 d x = G 0 1 ( ψ w x ) ( 3 s t ψ t ) d x ,
3 ρ 2 d d t 0 1 s t 2 d x + 3 ρ 2 d d t 0 1 s x 2 d x + 2 d d t 0 1 s 2 d x = 3 G 0 1 s t ( ψ w x ) d x 4 β 0 1 s t h ( s t ) d x .
The combination of (6) to (8) bearing in mind (4) and the fact that
G 2 d d t 0 1 ( ψ w x ) 2 d x = G 0 1 ψ t ( ψ w x ) d x G 0 1 w t x ( ψ w x ) d x
gives (5). □
Lemma 2.
Let ( w , ψ , s ) be the solution of system (3). Then the functional
F 1 ( t ) : = 3 I ρ 0 1 s s t d x 3 ρ 0 1 s 0 x w t ( y ) d y d x
satisfies, for any ε 1 > 0 , the estimate
F 1 ( t ) 3 D 0 1 s x 2 d x 3 γ 0 1 s 2 d x + ε 1 0 1 w t 2 d x + c 0 1 1 + 1 ε 1 s t 2 + 1 ϵ 1 h 2 ( s t ) d x .
Proof
Using the first and third equations in (3), we obtain
F 1 ( t ) : = 3 D 0 1 s x 2 d x 4 γ 0 1 s 2 d x + 3 I ρ 0 1 s t 2 d x 4 β 0 1 s h ( s t ) d x 3 ρ 0 1 s t 0 x w t ( y ) d y d x .
Using Young’s and Cauchy–Schwarz inequalities, the last two terms in (10), gives
4 β 0 1 s h ( s t ) d x γ 0 1 s 2 d x + 4 β 2 γ 0 1 g 2 ( s t ) d x ,
3 ρ 0 1 s t 0 x w t ( y ) d y d x ε 1 0 1 w t 2 d x + 9 ρ 2 4 ε 1 0 1 s t 2 d x .
The substitution of (11) and (12) into (10), gives (6). □
Lemma 3.
Let ( w , ψ , s ) be the solution of system (3) and assume that G ρ = D I ρ . Then the functional
F 2 ( t ) : = 3 ρ D 0 1 w t s x d x + 3 I ρ G 0 1 ( ψ w x ) s t d x
satisfies, for any ε 2 > 0 , the estimate
F 2 ( t ) G 2 0 1 ( ψ w x ) 2 d x + ε 2 0 1 ( 3 s t ψ t ) 2 d x + c 0 1 s x 2 + 1 + 1 ε 2 s t 2 + h 2 ( s t ) d x .
Proof
Direct computations and the fact that ψ t = ( 3 s t ψ t ) + 3 s t , yield
F 2 ( t ) = 3 G 2 0 1 ( ψ w x ) 2 d x 4 γ G 0 1 ( ψ w x ) s d x + 9 I ρ G 0 1 s t 2 d x 3 I ρ G 0 1 ( 3 s t ψ t ) s t d x 4 β G 0 1 ( ψ w x ) h ( s t ) d x .
Using Young’s and Poincaré’s inequalities, we obtain
4 γ G 0 1 ( ψ w x ) s d x G 2 0 1 ( ψ w x ) 2 d x + 4 γ 2 0 1 s x 2 d x
4 β G 0 1 ( ψ w x ) h ( s t ) d x G 2 0 1 ( ψ w x ) 2 d x + 4 β 2 0 1 g 2 ( s t ) d x
3 I ρ G 0 1 ( 3 s t ψ t ) s t d x ε 2 0 1 ( 3 s t s t ) 2 d x + 9 I ρ 2 G 2 4 ε 2 0 1 s t 2 d x .
By substituting (15)–(17) into (14), we end up with (13). □
Lemma 4.
Let ( w , ψ , s ) be the solution of system (3) and assume that G ρ = D I ρ . Then the functional
F 3 ( t ) : = ρ D 0 1 ( 3 s x ψ x ) w t d x + 3 I ρ G 0 1 ( 3 s ψ ) s t d x I ρ G 0 1 ( 3 s t ψ t ) w x d x
satisfies, for any ε 2 > 0 , the estimate
F 3 ( t ) D G 2 0 1 ( 3 s x ψ x ) 2 d x + ε 2 0 1 ( 3 s t ψ t ) 2 d x + c 0 1 s x 2 d x + c 0 1 ( ψ w x ) 2 d x + c 0 1 1 + 1 ε 2 s t 2 d x + c 0 1 h 2 ( s t ) d x .
Proof
Exploiting (3) and integrating by parts, we obtain
F 3 ( t ) = D G 0 1 ( 3 s x ψ x ) 2 d x + 3 I ρ G 0 1 ( 3 s t ψ t ) s t d x 3 G 2 0 1 ( 3 s ψ ) ( ψ w x ) d x 4 γ G 0 1 ( 3 s ψ ) s d x 4 β G 0 1 ( 3 s ψ ) h ( s t ) d x G 2 0 1 ( ψ w x ) w x d x .
Using the fact that w x = ( ψ w x ) ( 3 s ψ ) + 3 s , we end up with
F 3 ( t ) = D G 0 1 ( 3 s x ψ x ) 2 d x + 3 I ρ G 0 1 s t ( 3 s t ψ t ) d x 2 G 2 0 1 ( 3 s ψ ) ( ψ w x ) d x 4 γ G 0 1 s ( 3 s ψ ) d x 4 β G 0 1 s t ( 3 s ψ ) d x + G 2 0 1 ( ψ w x ) 2 d x 3 G 2 0 1 s ( ψ w x ) d x .
The use of Young’s and Poincaré inequalities, similar to (15)–(17), yields estimate (18). □
Lemma 5.
Let ( w , ψ , s ) be the solution of system (3). Then the functional
F 4 ( t ) : = 3 ρ 0 1 w t w d x 3 I ρ 0 1 s t ψ d x
satisfies
F 4 ( t ) 3 ρ 0 1 w t 2 d x + I ρ 4 0 1 ( 3 s t ψ t ) 2 d x + c 0 1 ( 3 s x ψ x ) 2 + ( ψ w x ) 2 + s x 2 + s t 2 + h 2 ( s t ) d x .
Proof
Using (3) and the substitution of ψ = ( 3 s ψ ) + 3 s along with its appropriate derivatives, gives
F 4 ( t ) = 3 ρ 0 1 w t 2 d x + 3 G 0 1 ( ψ w x ) 2 d x + 3 I ρ 0 1 ( 3 s t ψ t ) s t d x + 9 D 0 1 s x 2 d x 4 γ 0 1 ( 3 s ψ ) s d x + 12 β 0 1 s h ( s t ) d x + 12 γ 0 1 s 2 d x 4 β 0 1 ( 3 s ψ ) h ( s t ) d x 3 D 0 1 ( 3 s x ψ x ) s x d x .
As in the previous lemmas, (19) follows thanks to Young’s and Poincaré’s inequalities. □
Lemma 6.
Let ( w , ψ , s ) be the solution of system (3). Then the functional
F 5 ( t ) : = I ρ 0 1 ( 3 s ψ ) ( 3 s t ψ t ) d x
satisfies
F 5 ( t ) I ρ 0 1 ( 3 s t ψ t ) 2 d x + c 0 1 ( 3 s x ψ x ) 2 + ( ψ w x ) 2 d x .
Proof
Estimate (21) quickly follows thanks to system (3), integration by parts, Young’s, and Poincaré inequalities. □
Lemma 7.
Let ( w , ψ , s ) be the solution of system (3). Then, for N , N i ( i = 1 3 ) > 0 sufficiently large, the Lyapunov functional defined by
F ( t ) : = N E ( t ) + N 1 F 1 ( t ) + N 2 F 2 ( t ) + N 3 F 3 ( t ) + F 4 ( t ) + F 5 ( t )
satisfies, for some positive constant k ,
F ( t ) k E ( t ) + c 0 1 ( s t 2 + h 2 ( s t ) ) d x , t 0 .
Proof
Direct computations using (5), (9), (13), (18), (19), (21), and let
ε 1 = 2 ρ N 1 , ε 2 = I ρ 4 ( N 2 + N 3 ) ,
give
F ( t ) 3 D N 1 c N 2 c N 3 c 0 1 s x 2 d x 3 γ N 1 0 1 s 2 d x G 2 N 2 c N 3 c 0 1 ( ψ w x ) 2 d x ρ 0 1 w t 2 d x D G 2 N 3 c 0 1 ( 3 s x ψ x ) 2 d x + c N 1 2 + N 2 + N 3 + 1 0 1 h 2 ( s t ) d x I ρ 2 0 1 ( 3 s t ψ t ) 2 d x + c N 1 1 + N 1 + N 2 + ( N 2 + N 3 ) 2 + 1 0 1 s t 2 d x .
We now carefully choose the rest of the constants. First, we choose N 3 large so that
D G 2 N 3 c > 0 .
Next, we pick N 2 large so that
G 2 N 2 c N 3 c > 0 .
Finally, we select N 1 large so that
3 D N 1 c N 2 c N 3 c > 0 .
Thus, we end up with
F ( t ) α 0 1 s x 2 + s 2 + ( ψ w x ) 2 + w t 2 + ( 3 s x ψ x ) 2 + ( 3 s t ψ t ) 2 d x + c 0 1 s t 2 + h 2 ( s t ) d x
for some α > 0 . Using the energy functional defined by (4), we obtain (23), for some k > 0 .  □
Remark 3.
Choosing N large, it can easily be shown that F E in the sense that there exist two positive constants a and b such that
a E ( t ) F ( t ) b E ( t ) , t 0 .

3. Stability Result

This section concerns the proof of our stability result, and it states as follows
Theorem 1.
Let ( w , ψ , s ) be the solution of system (3) and assume (A1) holds. Then there exist positive constants k 1 , k 2 , k 3 , and ϵ 0 such that the solution of (1) satisfies
E ( t ) k 1 H 1 1 k 2 t + k 3 , t 0 ,
where
H 1 ( t ) = t 1 1 H 0 ( y ) d y and H 0 ( t ) = t H ( ϵ 0 t ) .
Proof
Using (23), we consider two cases:
Case I:H is linear. In this case, from (A1), we have
c 1 | y | | h ( y ) | c 2 | y | y R ,
so,
h 2 ( y ) c 2 y h ( y ) y R .
Thus, using (5), (23), and (27), we conclude that
F ( t ) k E ( t ) + c 0 1 h ( s t ) s t d x . = k E ( t ) c E ( t ) t R + .
So, by exploiting (25), it follows that
F 0 ( t ) : = F ( t ) + c E ( t ) E ( t ) .
satisfies, for some positive constant λ 1
F 0 ( t ) λ 1 F 0 ( t ) , t 0 .
Simple integration and using (28), yield
E ( t ) E ( 0 ) e λ 1 t .
Case II:H is nonlinear on [ 0 , ϵ ] . In this case, as in [25], we choose 0 < ϵ 1 ϵ such that
y h ( y ) min ϵ , H ( ϵ ) , | y | ϵ 1 .
Using (A1) and the continuity of h along the fact that | h ( y ) | > 0 , for s 0 , we deduce that
y 2 + h 2 ( y ) H 1 ( y h ( y ) ) , | y | ϵ 1 , c 1 | y | | h ( y ) | c 2 | y | , | y | ϵ 1 .
We now shift our attention to the last integral in (23):
0 1 ( s t 2 + h 2 ( s t ) ) d x .
To estimate this integral, we consider, as in [28], the following partition:
I 1 = x ( 0 , 1 ) : | s t | ϵ 1 , I 2 = x ( 0 , 1 ) : | s t | > ϵ 1 .
Thus, with I ( t ) defined by
I ( t ) = I 1 s t h ( s t ) d x ,
we obtain, thanks to Jensen inequality and the fact that H 1 is concave
H 1 ( I ( t ) ) c I 1 H 1 s t h ( s t ) d x .
Hence, using (30) and (31), we end up with
0 1 s t 2 + h 2 ( s t ) d x = I 1 s t 2 + h 2 ( s t ) d x + I 2 s t 2 + h 2 ( s t ) d x I 1 H 1 s t h ( s t ) d x + c I 2 s t h ( s t ) d x c H 1 ( I ( t ) ) c E ( t ) .
The substitution of (32) into (23) and using (28), we have
F 0 ( t ) k E ( t ) + c H 1 ( I ( t ) ) t R + .
Now, for ϵ 0 < ϵ and δ 0 > 0 , using (33) and the following properties of E and H:
E 0 , H > 0 , H > 0 on ( 0 , ϵ ] ,
we deduce that the functional F 1 , defined by
F 1 ( t ) : = H ϵ 0 E ( t ) E ( 0 ) F 0 ( t ) + δ 0 E ( t ) ,
satisfies, for some c 1 , c 2 > 0 ,
c 1 F 1 ( t ) E ( t ) c 2 F 1 ( t )
and
F 1 ( t ) : = ϵ 0 E ( t ) E ( 0 ) H ϵ 0 E ( t ) E ( 0 ) F 0 ( t ) + H ϵ 0 E ( t ) E ( 0 ) F ( t ) + δ 0 E ( t ) k E ( t ) H ϵ 0 E ( t ) E ( 0 ) + c H ϵ 0 E ( t ) E ( 0 ) H 1 I ( t ) T + δ 0 E ( t ) .
In order to estimate T in (35), we let H * be the convex conjugate of H defined by
H * ( y ) = y ( H ) 1 ( y ) H [ ( H ) 1 ( y ) ] y ( H ) 1 ( y ) , if y ( 0 , H ( ϵ ) ] ,
then, using the general Young’s inequality
A B H * ( A ) + H ( B ) , if A ( 0 , H ( ϵ ) ] , B ( 0 , ϵ ]
for A = H ϵ 0 E ( t ) E ( 0 ) and B = H 1 I ( t ) , we obtain
c H ϵ 0 E ( t ) E ( 0 ) H 1 I ( t ) c H * H ϵ 0 E ( t ) E ( 0 ) + c I ( t ) .
By using the energy functional (4) and (36), we end up with
c H ϵ 0 E ( t ) E ( 0 ) H 1 I ( t ) c ϵ 0 E ( t ) E ( 0 ) H ϵ 0 E ( t ) E ( 0 ) c E ( t ) .
Combining (35) and (37), we obtain
F 1 ( t ) k E ( t ) H ϵ 0 E ( t ) E ( 0 ) + c ϵ 0 β E ( t ) E ( 0 ) H ϵ 0 E ( t ) E ( 0 ) c E ( t ) + δ 0 E ( t ) k E ( 0 ) c ϵ 0 E ( t ) E ( 0 ) H ϵ 0 E ( t ) E ( 0 ) + ( δ 0 c ) E ( t ) .
Letting ϵ 0 = k 2 c E ( 0 ) , δ 0 = 2 c , and using the fact that E ( t ) 0 , we get
F 1 ( t ) a 1 E ( t ) E ( 0 ) H ϵ 0 E ( t ) E ( 0 ) = a 1 H 0 E ( t ) E ( 0 ) ,
where a 1 > 0 and H 0 ( t ) = t H ( ϵ 0 t ) .
So, using the fact that H is strictly convex on ( 0 , ϵ ] , we find that H 0 ( t ) , H 0 ( t ) > 0 on ( 0 , 1 ] . Hence, with F ˜ ( t ) = c 1 F 1 ( t ) E ( 0 ) and using (34) and (38), we have
F ˜ ( t ) E ( t )
and, for some k 2 > 0 ,
F ˜ ( t ) k 2 H 0 F ˜ ( t ) .
Inequality (40) implies that H 1 F ˜ ( t ) k 2 , where
H 1 ( t ) = t 1 1 H 0 ( y ) d y .
Thus, by integrating over [ 0 , t ] , bearing in mind the properties of H 0 , and the fact that H 1 is strictly decreasing on ( 0 , 1 ] we obtain, for some k 3 > 0 ,
F ˜ ( t ) H 1 1 k 2 t + k 3 t R + .
We complete the proof of Theorem 1 by using (39) and (41). □

4. Concluding Remarks

In this work, as in [19], we show (see (29)) that the structural damping is strong enough to exponentially stabilize the laminated Timoshenko beam system provided the wave speeds of the first two equations of the system are equal. A similar result was recently obtained in [29] when frictional damping is acting on the second equation. For the nonlinear case, the result is more general. For this case (nonlinear), it is an interesting open problem to investigate the case when the wave speeds of the first two equations of the system are not equal.

Author Contributions

Conceptualization, T.A.A.; Formal analysis, T.A.A. and A.M.N.; Funding acquisition, T.A.A.; Investigation, T.A.A., A.M.N. and H.A.S.; Methodology, T.A.A.; Validation, T.A.A.; Writing—original draft, T.A.A. and A.M.N.; Writing—review and editing, T.A.A., A.M.N. and H.A.S. All authors have read and agreed to the published version of the manuscript.

Funding

The first and third authors are supported by UHB under project number #G-106-2020. The second author thank FUD for continuous support.

Conflicts of Interest

The authors declare no conflict of interest.

References

  1. Hansen, S.W.; Spies, R.D. Structural damping in laminated beams due to interfacial slip. J. Sound Vib. 1997, 204, 183–202. [Google Scholar] [CrossRef]
  2. Wang, J.M.; Xu, G.Q.; Yung, S.P. Exponential Stabilization of Laminated Beams with Structural Damping and Boundary Feedback Controls. SIAM J. Control Optim. 2005, 44, 1575–1597. [Google Scholar] [CrossRef] [Green Version]
  3. Tatar, N.E. Stabilization of a laminated beam with interfacial slip by boundary controls. Bound. Value Probl. 2015, 2015, 169. [Google Scholar] [CrossRef] [Green Version]
  4. Mustafa, M.I. Boundary control of laminated beams with interfacial slip. J. Math. Phys. 2018, 59, 051508. [Google Scholar] [CrossRef]
  5. Cao, X.G.; Liu, D.Y.; Xu, G.Q. Easy test for stability of laminated beams with structural damping and boundary feedback controls. J. Dyn. Control Syst. 2007, 13, 313–336. [Google Scholar] [CrossRef]
  6. Feng, B. Well-posedness and exponential decay for laminated Timoshenko beams with time delays and boundary feedbacks. Math. Methods Appl. Sci. 2018, 41, 1162–1174. [Google Scholar] [CrossRef]
  7. Feng, B.; Ma, T.F.; Monteiro, R.N.; Raposo, C.A. Dynamics of laminated Timoshenko beams. J. Dyn. Differ. Equ. 2018, 30, 1489–1507. [Google Scholar] [CrossRef]
  8. Raposo, C.A.; Villagrá, O.V.; Muñoz Rivera, J.E.; Alves, M.S. Hybrid laminated Timoshenko beam. J. Math. Phys. 2017, 58, 101512. [Google Scholar] [CrossRef]
  9. Lo, A.; Tatar, N.E. Stabilization of laminated beams with interfacial slip. Electron. J. Differ. Equ. 2015, 129, 1–14. [Google Scholar]
  10. Mustafa, M.I. Laminated Timoshenko beams with viscoelastic damping. J. Math. Anal. Appl. 2018, 466, 619–641. [Google Scholar] [CrossRef]
  11. Mustafa, M.I. On the stabilization of viscoelastic laminated beams with interfacial slip. Z. Angew. Math. Phys. 2018, 69, 33. [Google Scholar] [CrossRef]
  12. Lo, A.; Tatar, N.E. Uniform stability of a laminated beam with structural memory. Qual. Theory Dyn. Syst. 2016, 15, 517–540. [Google Scholar] [CrossRef]
  13. Lo, A.; Tatar, N.E. Exponential stabilization of a structure with interfacial slip. Discrete Contin. Dyn. Syst. A 2016, 36, 6285–6306. [Google Scholar] [CrossRef] [Green Version]
  14. Li, G.; Kong, X.; Liu, W. General decay for a laminated beam with structural damping and memory: The case of non-equal wave speeds. J. Integral Equ. Appl. 2018, 30, 95–116. [Google Scholar] [CrossRef]
  15. Chen, Z.; Liu, W.; Chen, D. General decay rates for a laminated beam with memory. Taiwan. J. Math. 2019, 23, 1227–1252. [Google Scholar] [CrossRef]
  16. Apalara, T.A. On the Stability of a Thermoelastic Laminated Beam. Acta Math. Sci. 2019, 39, 1517–1524. [Google Scholar] [CrossRef]
  17. Apalara, T.A. Uniform stability of a laminated beam with structural damping and second sound. Z. Angew. Math. Phys. 2017, 68, 41. [Google Scholar] [CrossRef]
  18. Raposo, C.A. Exponential stability for a structure with interfacial slip and frictional damping. Appl. Math. Lett. 2016, 53, 85–91. [Google Scholar] [CrossRef]
  19. Alves, M.S.; Monteiro, R.N. Exponential stability of laminated Timoshenko beams with boundary/internal controls. J. Math. Anal. Appl. 2020, 482, 123516. [Google Scholar] [CrossRef]
  20. Seghour, L.; Tatar, N.E.; Berkani, A. Stability of a thermoelastic laminated system subject to a neutral delay. Math. Methods Appl. Sci. 2020, 43, 281–304. [Google Scholar] [CrossRef]
  21. Liu, W.; Luan, Y.; Liu, Y.; Li, G. Well-posedness and asymptotic stability to a laminated beam in thermoelasticity of type III. Math. Methods Appl. Sci. 2020, 43, 3148–3166. [Google Scholar] [CrossRef]
  22. Liu, W.; Zhao, W. Stabilization of a thermoelastic laminated beam with past history. Appl. Math. Opt. 2019, 80, 103–133. [Google Scholar] [CrossRef]
  23. Liu, W.; Kong, X.; Li, G. Asymptotic stability for a laminated beam with structural damping and infinite memory. Math. Mech. Solids 2020. [Google Scholar] [CrossRef]
  24. Feng, B.; Soufyane, A. Memory-type boundary control of a laminated Timoshenko beam. Math. Mech. Solids 2020. [Google Scholar] [CrossRef]
  25. Lasiecka, I.; Tataru, D. Uniform boundary stabilization of semilinear wave equations with nonlinear boundary damping. Differ. Integral Equ. 1993, 6, 507–533. [Google Scholar]
  26. Haraux, A. Nonlinear Evolution Equations—Global Behavior of Solutions; Springer: Berlin, Germany, 1981; Volume 841. [Google Scholar]
  27. Lions, J.L.; Magenes, E. Non-Homogeneous Boundary Value Problems and Applications; Springer: Berlin, Germany, 1972; Volume 1. [Google Scholar]
  28. Komornik, V. Exact Controllability and Stabilization: The Multiplier Method; John Wiley and Sons: Chichester, UK, 1995. [Google Scholar]
  29. Apalara, T.A.; Raposo, C.A.; Nonato, C.A. Exponential stability for laminated beams with a frictional damping. Arch. Math. 2020, 114, 471–480. [Google Scholar]

Share and Cite

MDPI and ACS Style

Apalara, T.A.; Nass, A.M.; Al Sulaimani, H. On a Laminated Timoshenko Beam with Nonlinear Structural Damping. Math. Comput. Appl. 2020, 25, 35. https://doi.org/10.3390/mca25020035

AMA Style

Apalara TA, Nass AM, Al Sulaimani H. On a Laminated Timoshenko Beam with Nonlinear Structural Damping. Mathematical and Computational Applications. 2020; 25(2):35. https://doi.org/10.3390/mca25020035

Chicago/Turabian Style

Apalara, Tijani A., Aminu M. Nass, and Hamdan Al Sulaimani. 2020. "On a Laminated Timoshenko Beam with Nonlinear Structural Damping" Mathematical and Computational Applications 25, no. 2: 35. https://doi.org/10.3390/mca25020035

APA Style

Apalara, T. A., Nass, A. M., & Al Sulaimani, H. (2020). On a Laminated Timoshenko Beam with Nonlinear Structural Damping. Mathematical and Computational Applications, 25(2), 35. https://doi.org/10.3390/mca25020035

Article Metrics

Back to TopTop