Search Results (34)

Reconfigurable intelligent surfaces (RISs) are regarded as a transformative technique for future wireless networks. Currently, the majority of research efforts have focused on channel estimation scenarios in communication systems assisted by a single passive RIS. However, single-RIS-assisted systems suffer from limited coverage performance, with significant performance degradation observed in dense obstacle environments. To mitigate the adverse impacts imposed by environmental factors, a dual-RIS-assisted communication system exhibits superior adaptability to practical scenarios. This work focuses on investigating such a system. It is worth noting that fully passive RISs lack the capability to process signals independently. Furthermore, when employing pilot-aided algorithms to acquire channel state information (CSI), wireless systems often encounter challenges arising from large channel matrix dimensions, thereby leading to substantial pilot overhead. To address the aforementioned issues, this paper proposes a novel semi-blind channel estimation method for multiple-input multiple-output (MIMO) systems aided by double reconfigurable intelligent surfaces (D-RISs). Specifically, we construct two tensor models, namely the Parallel Factor (PARAFAC) model and the Parallel Tucker2 model, for the received signal in two separate stages. By means of tensor decomposition, the joint channel estimation and symbol detection problem is reformulated as a least squares problem and solved using a two-stage algorithm. In the first stage, the ALS algorithm is adopted to estimate the transmitted symbols and provide initialization for the second stage. Then, in the second stage, the TALS algorithm is employed to obtain the final estimation results of the three sub-channels. Simulation results verify the effectiveness of the proposed receiver. Full article

This work presents the design and experimental validation of a 2 × 2 MIMO communication system assisted by a directly modulated analog radio-over-fiber (A-RoF) fronthaul, targeting low-complexity connectivity solutions for underserved/remote regions. The study details the complete end-to-end architecture, including a wireless access segment to complement the 20-km optical fronthaul link. The system is implemented on an software defined radio (SDR) platform using GNU Radio 3.7.11, running on Ubuntu 18.04 with kernel 4.15.0-213-generic. It also employs adaptive modulation driven by real-time signal-to-noise ratio (SNR) estimation to keep bit error rate (BER) close to zero while maximizing throughput. Performance is characterized over 20 km of single-mode fiber (SMF) using coarse wavelength division multiplexing (WDM) and assessed through root mean square error vector magnitude (${\mathrm{EVM}}_{\mathrm{RMS}}$), throughput, and spectral integrity. The results identify an optimum radio-frequency drive region around $-16$ dBm enabling high-order modulation (e.g., 256-QAM), whereas RF input powers above approximately $-10$ dBm increase ${\mathrm{EVM}}_{\mathrm{RMS}}$ due to nonlinearity in the RF front-end/low-noise amplifier (LNA) and direct modulation stage, forcing the adaptive scheme to reduce modulation order and throughput. Over the optical-power sweep, when the incident optical power exceeds approximately $-8$ dBm, the system reaches ∼130 Mbps (24-MHz channel) with ${\mathrm{EVM}}_{\mathrm{RMS}}$ approaching ∼1%, highlighting the need for careful joint tuning of RF drive, optical launch power, and wavelength allocation across transceivers. Finally, the integrated access link employs diplexers for transmitter/receiver separation in a 2 × 2 configuration with 2.8 m antenna separation and low channel correlation, demonstrating a 10 m proof-of-concept range and enabling end-to-end spectrum/EVM/throughput observations across the full communication chain. Full article

We propose a low-complexity hybrid beamforming method for massive Multiple-Input Multiple-Output (MIMO) systems that is robust to Channel State Information (CSI) estimation errors. These errors stem from hardware impairments, pilot contamination, limited training, and fast fading, causing spectral-efficiency loss. However, existing hybrid beamforming solutions typically either assume near-perfect CSI or rely on greedy/black-box designs without an explicit mechanism to regularize the error-distorted singular modes, leaving a gap in unified, low-complexity, and theoretically grounded robustness. We unfold the Alternating Direction Method of Multipliers (ADMM) into a trainable Deep Learning (DL) network, termed DL-ADMM, to jointly optimize Radio-Frequency (RF) and baseband precoders and combiners. In DL-ADMM, the ADMM update mappings are learned (layer-wise parameters and projections) to amortize the joint RF/baseband optimization, whereas Regularized Singular Value Decomposition (RSVD) acts as an analytical regularizer that reshapes the observed channel’s singular values to suppress noise amplification under imperfect CSI. RSVD is integrated to stabilize singular modes and curb noise amplification, yielding a unified and scalable design. For ${\sigma }_e^2=0.1$, the proposed DL-ADMM-Reg achieves approximately 8–11 bits/s/Hz higher spectral efficiency than Orthogonal Matching Pursuit (OMP) at Signal-to-Noise Ratio (SNR) $=20$–40 dB, while remaining within <1 bit/s/Hz of the digital-optimal benchmark across both $(N_t,N_r)=(32,32)$ and $(64,64)$ settings. Simulations confirm higher spectral efficiency and robustness than OMP and Adaptive Phase Shifters (APSs). Full article

Weighted sum-rate (WSR) maximization in downlink massive multi-user multiple-input (MU-MIMO) with per-antenna power constraints (PAPCs) and imperfect channel state information (CSI) is computationally challenging. Classical weighted minimum mean-square error (WMMSE) algorithms, in particular, have per-iteration costs that scale cubically with the number of base-station antennas. This article proposes a robust low-complexity WMMSE-based precoding framework (RLC-WMMSE) tailored for massive MU-MIMO downlink under PAPCs and stochastic CSI mismatch. The algorithm retains the standard WMMSE structure but incorporates three key enhancements: a diagonal dual-regularization scheme that enforces PAPCs via a lightweight projected dual ascent with row-wise safety projection; a Woodbury-based transmit update that replaces the dominant $M\times M$ inversion with an $\left(NK\right)\times \left(NK\right)$ symmetric positive-definite solve, greatly reducing the per-iteration complexity; and a hybrid switching mechanism with adaptive damping that blends classical and low-complexity updates to improve robustness and convergence under channel estimation errors. We also analyze computational complexity and signaling overhead for both TDD and FDD deployments. Simulation results over i.i.d. and spatially correlated channels show that the proposed RLC-WMMSE scheme achieves WSR performance close to benchmark WMMSE-PAPCs designs while providing substantial runtime savings and strictly satisfying the per-antenna power limits. These properties make RLC-WMMSE a practical and scalable precoding solution for large-scale MU-MIMO systems in future wireless sensor and communication networks. Full article

Electroencephalography (EEG) communication technology with ultra-low power consumption, high transmission data rates, and low latency plays a significant role in mHealth, telemedicine, and Internet of Medical Things (IoMT). In this paper, generalized frequency division multiplexing (GFDM)-based direct mapping (DM) multi-input—multi-output (MIMO) mobile EEG communication technology (MECT) is proposed for implementation with the above-mentioned applications. The (2000, 1000) low-density parity-check (LDPC) code, four-quadrature amplitude modulation (4-QAM), a power assignment mechanism, and the 3rd Generation Partnership Project (3GPP) cluster delay line (CDL) channel model D were integrated into the proposed EEGCT. The transmission bit error rates (BERs), mean square errors (MSEs), and Pearson-correlation coefficients (PCCs) of the original and received EEG signals were evaluated. Simulation results show that, with a signal to noise ratio (SNR) of 14.51 dB, with a channel estimation error (CEE) of 5%, the BER, MSE, and PCC of the original and received EEG signals were 9.9777 × 10⁻⁸, 1.440 × 10⁻⁵ and 0.999999998, respectively, whereas, with an SNR of 15.0004 dB and a CEE of 10%, they were 9.9777 × 10⁻⁸, 1.4368 × 10⁻⁵, and 0.999999997622151, respectively. As the BER value, and PS saving are 9.9777 × 10⁻⁸, and 40%, respectively. With the CEE changes from 0% to 5%, and 5% to 10%, the N₀ values of the proposed MECT decrease by approximately 0.0022 and 0.002, respectively. The MECT has excellent EEG signal transmission performance. Full article

Integrated Sensing And Communication (ISAC) has been applied to the Internet of Things (IoT) network as a promising 6G technology due to its ability to enhance spectrum utilization and reduce resource consumption, making it ideal for high-precision sensing applications. However, while the introduction of millimeter Wave (mmWave) and massive Multiple-Input Multiple-Output (MIMO) technologies can enhance the performance of ISAC systems, they extend the near-field region, rendering traditional channel parameter estimation algorithms ineffective due to the spherical wavefront channel model. Aiming to address the challenge, we propose a tensor-based channel parameter estimation and localization algorithm for the near-field mmWave massive MIMO-Orthogonal Frequency Division Multiplexing (OFDM) ISAC systems. Firstly, the received signal at the User Terminal (UT) is constructed as a third-order tensor to retain the multi-dimensional features of the data. Then, the proposed tensor-based algorithm achieves the channel parameter estimation and target localization by exploiting the second-order Taylor expansion and intrinsic structure of tensor factor matrices. Furthermore, the Cramér–Rao Bounds (CRBs) of channel parameters and position are derived to establish the lower bound of errors. Simulation results show that the proposed tensor-based algorithm is superior compared to the existing algorithms in terms of channel parameter estimation and localization accuracy in ISAC systems for IoT network, achieving errors that approach the CRBs. Specifically, the proposed algorithm attains a 79.8% improvement in UT positioning accuracy compared to suboptimal methods at SNR = 5 dB. Full article

This paper presents a blind source separation (BSS)-based framework for joint communication and sensing (JCAS) in in-band full-duplex (IBFD) multiple-input multiple-output (MIMO) systems operating under time-varying channel conditions. Conventionally, self-interference (SI) in IBFD systems is a major obstacle to recovering the signal of interest (SOI). Under the JCAS paradigm, however, this high-power SI signal presents an opportunity for efficient sensing. Since each transceiver node has access to the original SI signal, its environmental reflections can be exploited to estimate channel conditions and detect changes, without requiring dedicated radar waveforms. We propose a blind source separation (BSS)-based framework to simultaneously perform self-interference cancellation (SIC) and extract sensing information in IBFD MIMO settings. The approach applies the Fast Independent Component Analysis (FastICA) algorithm in dynamic scenarios to separate the SI and SOI signals while enabling simultaneous signal recovery and channel estimation. Simulation results quantify the trade-off between estimation accuracy and channel dynamics, demonstrating that while FastICA is effective, its performance is fundamentally limited by a frame size optimized for the rate of channel variation. Specifically, in static channels, the signal-to-residual-error ratio (SRER) exceeds 22 dB with 500-symbol frames, whereas for moderately time-varying channels, performance degrades significantly for frames longer than 150 symbols, with SRER dropping below 4 dB. Full article

Reconfigurable Intelligent Surfaces (RISs) are among the key technologies envisaged for sixth-generation (6G) multiple-input multiple-output (MIMO)–orthogonal frequency division multiplexing (OFDM) wireless systems. However, their passive nature and the frequent absence of a line-of-sight (LoS) path in dense urban environments make uplink channel estimation and localization challenging tasks. Therefore, to achieve channel estimation and localization, this study models the RIS-mobile station (MS) channel as a double-sparse angular structure and proposes a hybrid channel parameter estimation framework for RIS-assisted MIMO-OFDM systems. In the hybrid framework, Simultaneous Orthogonal Matching Pursuit (SOMP) first estimates coarse angular supports. The coarse estimates are refined by a novel refinement stage employing a Variational Bayesian Expectation Maximization (VBEM)-based Off-Grid Sparse Bayesian Learning (OG-SBL) algorithm, which jointly updates azimuth and elevation offsets via Newton-style iterations. An Angle of Arrival (AoA)–Angle of Departure (AoD) matching algorithm is introduced to associate angular components, followed by a 3D localization procedure based on non-LoS (NLoS) multipath geometry. Simulation results show that the proposed framework achieves high angular resolution; high localization accuracy, with 97% of the results within 0.01 m; and a channel estimation error of 0.0046% at 40 dB signal-to-noise ratio (SNR). Full article

High route loss and line-of-sight requirements are two of the fundamental challenges of millimeter-wave (mm-wave) communications that are mitigated by incorporating sensor technology. Sensing gives the deep reinforcement learning (DRL) agent comprehensive environmental feedback, which helps it better predict channel fluctuations and modify beam patterns accordingly. For multi-user massive multiple-input multiple-output (mMIMO) systems, hybrid precoding requires sophisticated real-time low-complexity power allocation (PA) approaches to achieve near-optimal capacity. This study presents a unique angular-based hybrid precoding (AB-HP) framework that minimizes radio frequency (RF) chain and channel estimation while optimizing energy efficiency (EE) and spectral efficiency (SE). DRL is essential for mm-wave technology to make adaptive and intelligent decision-making possible, which effectively transforms wireless communication systems. DRL optimizes RF chain usage to maintain excellent SE while drastically lowering hardware complexity and energy consumption in an AB-HP architecture by dynamically learning optimal precoding methods using environmental angular information. This article proposes enabling dual optimization of EE and SE while drastically lowering beam training overhead by incorporating maximum reward beam training driven (RBT) in the DRL. The proposed RBT-DRL improves system performance and flexibility by dynamically modifying the number of active RF chains in dynamic network situations. The simulation results show that RBT-DRL-driven beam training guarantees good EE performance for mobile users while increasing SE in mm-wave structures. Even though total power consumption rises by 45%, the SE improves by 39%, increasing from 14 dB to 20 dB, suggesting that this strategy could successfully achieve a balance between performance and EE in upcoming B5G networks. Full article

Modern wireless communication systems have undergone a radical change with the introduction of multiple-input multiple-output (MIMO) antennas, which provide increased channel capacity, fast data rates, and secure connections. To achieve real-time requirements, such antenna technology needs to have good gains, wider bandwidths, satisfactory radiation characteristics, and high isolation. This article presents an eight-element CPW-fed antenna for the 5G mid-band. The proposed antenna consists of eight symmetrical, modified circular monopole antennas with a connected CPW-fed ground plane that offers 24 dB isolation over the operating range. The antenna is further investigated in terms of the scattering parameters, and radiation characteristics under both the x and y-axis bending scenarios. The antenna holds a volume of 83 × 129 × 0.1 mm³ and covers a measured impedance bandwidth of 4.5–5.5 GHz (20%) with an average gain of 4 dBi throughout the operating band. MIMO diversity performance of the antenna is performed, and the antenna exhibits good performance suitable for MIMO applications. Furthermore, the channel capacity (CC) is estimated, and the antenna gives a value of 41.8–42.6 bps/Hz within the operating bandwidth, which is very close to an ideal 8 × 8 MIMO system. The antenna shows an excellent match between the simulated and measured findings. Full article

Reconfigurable Intelligent Surface (RIS)-assisted Unmanned Aerial Vehicle (UAV) communications face a critical security threat from impersonation attacks, where adversaries impersonate legitimate entities to infiltrate networks to obtain private data or unauthorized access. To combat such security threats, this paper proposes a novel physical layer (PHY-layer) authentication scheme for validating UAV identity in RIS-enabled UAV wireless networks. Considering that most existing works focus on traditional communication systems such as IoT and millimeter wave multiple-input multiple-output (MIMO) systems, there is currently no mature PHY-layer authentication scheme to serve RIS-UAV communication systems. To this end, our scheme leverages the unique characteristics of cascaded channels related to RIS to verify the legitimacy of UAV transmitting signals to the base station (BS). To be more precise, we first use the least squares estimate method and coordinate a descent-based algorithm to extract the cascaded channel feature. Next, we explore a quantizer to quantize the fluctuations of the channel gain that are related to the extracted channel feature. The 1-bit quantizer’s output findings are exploited to generate the authentication decision criteria, which are then tested using a binary hypothesis. The statistical signal processing technique is utilized to obtain the analytical formulations for detection and false alarm probabilities. We also conduct a computational complexity analysis of the proposed scheme. Finally, the numerical results validate the effectiveness of the proposed performance metric models and show that our detection performance can reach over 90% accuracy at a low signal-to-noise ratio (e.g., −8 dB), with a 10% improvement in detection accuracy compared with existing schemes. Full article

This paper investigates single-user uplink and two-user downlink channel estimation in reconfigurable intelligent surface (RIS)-aided millimeter-wave (mmWave) massive multiple-input multiple-output (MIMO) wireless communication systems. Because of the difficulty associated with the estimation of channels in RIS-aided wireless communication systems, channel state information (CSI) is assumed to be known at the receiver in some previous works in the literature. By assuming that prior knowledge of the line-of-sight (LoS) channel between the RIS and the base station (BS) is known, two compressive sensing-based channel estimation schemes that are based on simultaneous orthogonal matching pursuit and structured matching pursuit (StrMP) algorithms are proposed for estimation of uplink channel between RIS and user equipment (UE), and joint estimations of downlink channels between BS and a UE, and between RIS and another UE, respectively. The proposed channel estimation schemes exploit the inherent common sparsity shared by the angular domain mmWave channels at different subcarriers. The superiority of one of the proposed channel estimation techniques, the StrMP-based channel estimation technique, with negligibly higher computational complexity cost compared with other channel estimators, is documented through extensive computer simulation. Specifically, with a reduced pilot overhead, the proposed StrMP-based channel estimation scheme exhibits better performance than other channel estimation schemes considered in this paper for signal-to-noise ratio (SNR) between 0 dB and 5 dB upward at different instances for both uplink and downlink scenarios, respectively. However, below these values of SNR the proposed StrMP-based channel estimation scheme will require higher pilot overhead to perform optimally. Full article

Unmanned aerial vehicle (UAV) air-to-ground (AG) communication plays a critical role in the evolving space–air–ground integrated network of the upcoming sixth-generation cellular network (6G). The integration of massive multiple-input multiple-output (MIMO) systems has become essential for ensuring optimal performing communication technologies. This article presents a novel dual-driven learning-based network for millimeter-wave (mm-wave) massive MIMO symbol detection of UAV AG communications. Our main contribution is that the proposed approach combines a data-driven symbol-correction network with a model-driven orthogonal approximate message passing network (OAMP-Net). Through joint training, the dual-driven network reduces symbol detection errors propagated through each iteration of the model-driven OAMP-Net. The numerical results demonstrate the superiority of the dual-driven detector over the conventional minimum mean square error (MMSE), orthogonal approximate message passing (OAMP), and OAMP-Net detectors at various noise powers and channel estimation errors. The dual-driven MIMO detector exhibits a 2–3 dB lower signal-to-noise ratio (SNR) requirement compared to the MMSE and OAMP-Net detectors to achieve a bit error rate (BER) of $1\times {10}^{-2}$ when the channel estimation error is −30 dB. Moreover, the dual-driven MIMO detector exhibits an increased tolerance to channel estimation errors by 2–3 dB to achieve a BER of $1\times {10}^{-3}$. Full article

This study investigates receiver design solutions for distributed Massive Multiple Input Multiple Output (D-m MIMO) systems, taking into account parameters such as number of access points as well as concerns related to channel estimates that use single-carrier frequency-domain equalization (SC-FDE). A significant contribution of this research is the integration of Low-Density Parity-Check (LDPC) codes to simplify coding complexity and enhance communication efficiency. The research examines different receiver designs, such as spatial antenna correlation and sophisticated channel estimation methods. The authors propose integrating LDPC codes into the receiver architecture to simplify computations and enhance error correction and decoding. Moreover, the paper examines performance evaluation measures and approaches, highlighting the trade-offs among complexity, spectral efficiency, and error performance. The comparative analysis indicates the benefits, in terms of performance, of incorporating LDPC codes and improving system throughput and dependability. We examine four distinct receiver algorithms: zero-forcing (ZF), minimum mean square error (MMSE), maximum ratio combining (MRC), and equal gain combining (EGC). The study shows that MRC and EGC receivers work well in D-m MIMO because they make the receiver system less computationally demanding. Full article

To address the limitations of poor environmental adaptability, unsatisfactory bit-error performance, and high complexity of conventional antenna selection algorithms applied to a multi-array visible-light optical generalized spatial multiplexing–multiple-input multiple-output (OGSMP-MIMO) system, an OGSMP-MIMO system based on Pearson coefficient antenna selection is proposed. The algorithm adopts the correlation of Pearson coefficients among photoelectric detector (PD) terminals at different positions and active transmit antennas to select the optimal antenna combination without relying on the accuracy of channel estimation, for realizing the multiplexing of the time and space domains, and to improve the bit-error performance. Finally, experiments were conducted to verify the feasibility of the antenna selection algorithm, based on the Pearson coefficients. The results indicated that when the bit-error rate reached 10⁻⁶, using the antenna selection algorithm based on the Pearson coefficient, the signal-to-noise ratio was improved by 2.7 dB and 3.7 dB when compared with the norm-based antenna and random selection algorithms, respectively. In addition, increasing the number of active transmitting antennas can improve the transmission rate; however, the bit-error performance will be compromised. In the same modulation mode, increasing the number of transmitting antennas will reduce the bit-error performance. Full article