Search Results (3,703)

Traditional liquid electrolyte batteries face safety concerns such as leakage and flammability, while further optimization has reached a bottleneck. Solid electrolytes are therefore considered a promising solution. Here, a PEO–LiTFSI–LATP (PELT) composite electrolyte was developed by incorporating nanosized Li_1.3Al_0.3Ti_1.7(PO₄)₃ fillers into a polyethylene oxide matrix, effectively reducing crystallinity, enhancing mechanical robustness, and providing additional Li⁺ transport channels. The PELT electrolyte exhibited an electrochemical stability window of 4.9 V, an ionic conductivity of 1.2 × 10⁻⁴ S·cm⁻¹ at 60 °C, and a Li⁺ transference number (tLi+) of 0.46, supporting stable Li plating/stripping for over 600 h in symmetric batteries. More importantly, to address poor electrode–electrolyte contact in conventional layered cells, we proposed an integrated electrode–electrolyte architecture by in situ coating the PELT precursor directly onto LiFePO₄ cathodes. This design minimized interfacial impedance, improved ion transport, and enhanced electrochemical stability. The integrated PELT/LFP battery retained 74% of its capacity after 200 cycles at 1 A·g⁻¹ and showed superior rate capability compared with sandwich-type batteries. These results highlight that coupling LATP-enhanced polymer electrolytes with an integrated architecture is a promising pathway toward high-safety, high-performance solid-state lithium-ion batteries. Full article

With their considerable capacity and structurally favorable characteristics, layered transition metal oxides have become strong contenders for cathode use in sodium-ion batteries (SIBs). Nevertheless, their practical deployment is challenged by pronounced capacity loss, predominantly induced by unstable cathode–electrolyte interphase (CEI) at elevated voltages. In this study, difluoroethylene carbonate (DFEC) is introduced as a functional electrolyte additive to engineer a robust and uniform CEI. The fluorine-enriched CEI effectively suppresses parasitic reactions, mitigates continuous electrolyte decomposition, and facilitates stable Na⁺ transport. Consequently, Na/NaNi_1/3Fe_1/3Mn_1/3O₂ (Na/NFM) cells with 2 wt.% DFEC retain 78.36% of their initial capacity after 200 cycles at 1 C and 4.2 V, demonstrating excellent long-term stability. Density functional theory (DFT) calculations confirm the higher oxidative stability of DFEC compared to conventional solvents, further supporting its interfacial protection role. This work offers valuable insights into electrolyte additive design for high-voltage SIBs and provides a practical route to significantly improve long-term electrochemical performance. Full article

Optical transmission gratings with quasi-sinusoidal surface-relief profiles were inscribed in IOG and Pyrex glasses and in Bi₁₂GeO₂₀, Er: LiNbO_3, and Er: Fe: LiNbO₃ crystals by microbeams of carbon, nitrogen, and oxygen ions at ion energies of 5, 6, and 10.5 MeV. Grating constants were 4, 8, and 16 μm. Amplitudes of the surface-relief gratings were in the 10–2000 nm range. The diffraction efficiency of the gratings was measured at a wavelength of 640 nm. Maximum diffraction efficiencies were close to the theoretical maximum of 33% for thin gratings. Grating profiles were measured by optical microscopic profilometry. Measurement of the diffraction efficiencies at higher orders and Fourier analysis of the grating profiles revealed the dependence of the residual nonlinearity of the grating profiles on the implanted ion fluence. The ion microbeam-written gratings can be used as light coupling elements in integrated optics for sensors and telecommunication. Full article

This study investigates the formation of hydroxyl radicals (OH radicals) in cavitation bubble plasma-treated water (CBPTW) using a chemical probe method. CBPTW samples were prepared with different electrode materials (W, Fe, Cu, and Ag), and the chemical scavenger was added two minutes after the completion of cavitation and plasma treatments. The concentrations of metal ions and hydrogen peroxide (H₂O₂) generated in the CBPTW were also measured over time. This study reveals a novel mechanism whereby metal nanoparticles and ions released from electrodes catalyze the continuous generation of hydroxyl radicals in CBPTW, which has not been fully addressed in previous studies. The results suggest a continuous generation of OH radicals in CBPTW prepared with W, Fe, and Cu electrodes, with the amount of OH radicals produced in the order Cu > Fe > W. The study reveals a correlation between OH radical production and electrode wear, suggesting that the continuous generation of OH radicals in CBPTW results from the catalytic decomposition of H₂O₂ by metal nanoparticles or ions released from the electrodes. It should be noted that cavitation bubble plasma (CBP) is fundamentally different from sonochemistry. While sonochemistry utilizes ultrasound-induced cavitation to generate radicals, CBP relies on plasma discharge generated inside cavitation bubbles. No ultrasound was applied in this study; therefore, all observed radical formation is attributable exclusively to plasma processes rather than sonochemical effects. However, the precise mechanism of continuous OH radical formation in CBPTW remains unclear and requires further investigation. These findings provide new insights into the role of electrode materials in continuous OH radical generation in cavitation bubble plasma treated water, offering potential applications in water purification and sterilization technologies. Full article

In this work, the removal of Cu(II) ions from an aqueous effluent was studied using an Mg/Fe layered double hydroxide (LDH) as the adsorbent. The material was synthesized and characterized before and after the adsorption process to identify structural and morphological changes induced by copper uptake. Techniques such as X-ray diffraction (XRD), scanning electron microscopy with energy-dispersive spectroscopy (SEM-EDS), ultraviolet-visible spectroscopy (UV-Vis), Raman spectroscopy, and nitrogen physisorption (BET) were employed to confirm the interaction between the metal ions and the LDH surface. The LDH-Mg/Fe exhibited a high maximum adsorption capacity of 526 mg/g, and the adsorption kinetics followed a pseudo-second-order model, achieving over 90% removal of Cu(II) within 2.5 h. The Cu(II)-loaded material was subsequently evaluated as a sustainable catalyst in two applications: (i) an organic synthesis via “click” chemistry, reaching yields of up to 85%, and (ii) the decoloration of Congo Red via a Fenton-like process, achieving a decoloration efficiency of at least 84%. These dual uses demonstrate the potential of Cu(II)-loaded LDH as a cost-effective and environmentally friendly approach to simultaneous pollutant removal and catalytic valorization. Full article

NASICON-type Li_1+XFe_XTi_2-X(PO₄)₃ (x = 0.1, 0.3, 0.4) solid electrolytes for all-solid-state Li-ion batteries were synthesized using a sol–gel method. This study investigated the impact of substituting Fe³⁺ (0.645 Å), a trivalent cation, for Ti⁴⁺ (0.605 Å) on ionic conductivity. Li_1+XFe_XTi_2-X(PO₄)₃ samples, subjected to various sintering temperatures, were characterized using TG-DTA, XRD with Rietveld refinement, XPS, FE-SEM, and AC impedance to evaluate composition, crystal structure, fracture-surface morphology, densification, and ionic conductivity. XRD analysis confirmed the formation of single-crystalline NASICON-type Li_1+XFe_XTi_2-X(PO₄)₃ at all sintering temperatures. However, impurities in the secondary phase emerged owing to the high sintering temperature above 1000 °C and increased Fe content. Sintered density increased with the densification of Li_1+XFe_XTi_2-X(PO₄)₃, as evidenced by FE-SEM observations of sharper edges of larger quasi-cubic grains at elevated sintering temperatures. At 1000 °C, with Fe content exceeding 0.4, grain coarsening resulted in additional grain boundaries and internal cracks, thereby reducing the sintered density. Li_1.3Fe_0.3Ti_1.7(PO₄)₃ sintered at 900 °C exhibited the highest density among the other conditions and achieved the maximum total ionic conductivity of 1.51 × 10⁻⁴ S/cm at room temperature, with the lowest activation energy for Li-ion transport at 0.37 eV. In contrast, Li_1.4Fe_0.4Ti_1.6(PO₄)₃ sintered at 1000 °C demonstrated reduced ionic conductivity owing to increased complex impedance associated with secondary phases and grain crack formation. Full article

In this work, a novel solid polymer electrolyte with a disordered structure has been designed, combining polyethylene glycol (PEG) as the flexible segments and hexamethylene diisocyanate (HDI) as the rigid segments. The synthesis was realized by alternating flexible PEG with rigid HDI through a peptide bond (–CO–NH–), which disrupts the ordered structures of PEG, generating electron-deficient Lewis acid groups. The pathbreaking introduction of HDI blocks not only bridges links between the PEG molecules but also generates electron-deficient Lewis acid groups. Therefore, the original ordered structures of PEG are disrupted by both the alternating chains between PEG and HDI and the Lewis acid groups. As a result, the PEG_H/L4000 electrolytes (PEG molecular weight of 4000) exhibit a strong anion-capture ability that decreases the crystallinity of polymers, which further achieves a high ionic conductivity close to 10⁻³ S·cm⁻¹ with the lithium-ion transference numbers up to 0.88. The symmetric Li|PEG_H/L4000|Li cells maintain a low and stable voltage polarization for more than 800 h at 0.1 mA·cm⁻². Furthermore, the LiFePO₄|PEG_H/L4000|Li all-solid-state cells perform well both in cycling and rate performances. The design of polymer disordered structures for polymer electrolytes provides a new thought for manufacturing all-solid-state lithium-ion batteries with high safety as well as long life. Full article

This study investigates the corrosion inhibition efficiency of [2-(thiophen-2-yl)-1-(thiophen-2-ylmethyl)-1H-benzo[d]imidazole] and its Zn and Cu complexes for mild steel in 1.0 M HCl. The ligand was selected for its non-toxic profile and high electron density, favoring strong adsorption onto the metal surface. Electrochemical methods, including EIS, PDP, LPR, and CASP, were employed to evaluate the inhibitors’ performance. The results showed a significant decrease in corrosion current density and increased polarization resistance, with the Zn complex achieving the highest inhibition efficiency (93.8%). EIS fitting confirmed the formation of a protective film with high charge transfer and film resistance. Surface analyses by SEM and EDS revealed smoother steel morphology and inhibitor adsorption. XPS confirmed the presence of Fe³⁺, Zn²⁺and Cu²⁺ oxides, as well as all active inhibitor elements on the surface, supporting a mixed inhibition mechanism. The enhanced performance of the metal complexes is attributed to synergistic effects between the metal ions and the heterocyclic ligand, offering a promising strategy for the design of effective and environmentally friendly corrosion inhibitors. Full article

The electrochemical performance of Li-ion batteries employing LiFePO₄ (LFP) cathodes supported by bio-sourced activated carbon derived from millet cob (MC) and water hyacinth (WH) were systematically investigated. Carbon activation was carried out using potassium hydroxide (KOH) at varying mass ratios of KOH to precursor material: 1:1, 2:1, and 5:1 for both WH and MC-derived carbon. The physical properties (X-ray diffraction patterns, BET surface area, micropore and mesopore volume, conductivity, etc.) and electrochemical performance (specific capacity, discharge at various current rates, electrochemical impedance measurement, etc.) were determined. Material characterization revealed that the activated carbon derived from MC exhibits an amorphous structure, whereas that obtained from WH is predominantly crystalline. High specific surface areas were achieved with activated carbons synthesized using a low KOH-to-carbon mass ratio (1:1), reaching 413.03 m²·g⁻¹ for WH and 216.34 m²·g⁻¹ for MC. However, larger average pore diameters were observed at higher activation ratios (5:1), measuring 8.38 nm for KOH/WH and 5.28 nm for KOH/MC. For both biomass-derived carbons, optimal electrical conductivity was obtained at a 2:1 activation ratio, with values of 14.7 × 10⁻³ S·cm⁻¹ for KOH/WH and 8.42 × 10⁻³ S·cm⁻¹ for KOH/MC. The electrochemical performance of coin cells based on cathodes composed of 85% LiFePO₄, 8% of these activated carbons, and 7% polyvinylidene fluoride (PVDF) as a binder, with lithium metal as the anode were studied. The LiFePO₄/C (LFP/C) cathodes exhibited specific capacities of up to 160 mAh·g⁻¹ at a current rate of C/12 and 110 mAh·g⁻¹ at 5C. Both LFP/MC and LFP/WH cathodes exhibit optimal energy density at specific values of pore size, pore volume, charge transfer resistance (R_ct), and diffusion coefficient (D_Li), reflecting a favorable balance between ionic transport, accessible surface area, and charge conduction. Maximum energy densities relative to active mass were recorded at 544 mWh·g⁻¹ for LFP/MC 2:1, 554 mWh·g⁻¹ for LFP/WH 2:1, and 568 mWh·g⁻¹ for the reference LFP/graphite system. These performance results demonstrate that the development of high-performing bio-sourced activated carbon depends on the optimization of various parameters, including chemical composition, specific surface area, pore volume and size distribution, as well as electrical conductivity. Full article

This study aims to determine the optimal Mo content for corrosion resistance in two alloys, FeCoCrNiMo_x and Fe_0.5CoCrNiMo_x. The alloys were fabricated using laser powder bed fusion (LPBF) technology with varying Mo contents (x = 0, 0.05, 0.1, 0.15). The corrosion behavior of these alloys was investigated in 3.5 wt.% NaCl solution at room temperature and 60 °C using electrochemical testing and X-ray photoelectron spectroscopy (XPS). The results show that all alloys exhibit good corrosion resistance at room temperature. However, at 60 °C, both alloys without Mo addition exhibit severe corrosion, while the Fe_0.5CoCrNiMo_0.1 alloy demonstrates the best corrosion resistance while maintaining the highest strength. The enhanced corrosion resistance is attributed to the optimal molybdenum addition, which refines the passive film structure and promotes the formation of Cr₂O₃. Furthermore, molybdenum oxide exists as MoO₄²⁻ ions on the surface of the passive film, significantly improving the alloy’s corrosion resistance in chloride-containing environments. Full article

The activation of persulfate (PS) to oxidize and degrade 2,4-dichlorophenol (2,4-DCP) in aqueous solution represents a prevalent advanced oxidation technology. This study established a PS activation system using sulfide-modified nanoscale zero-valent iron supported on biochar (S-nZVI@BC). The optimal conditions included a PS:2,4-DCP mass ratio of 70:1 and S-nZVI@BC:PS of 1.5:1. The activator had excellent stability after being reused five times, which lead to high cost-effectiveness and sustainable usability. This system exhibited broad pH adaptability (3–11), with enhanced efficiency under acidic/neutral conditions. Chloride ion, nitrate, and carbonate had effects during the degradation. During the initial degradation phase, S-nZVI@BC played a primary role, with a greater contribution rate of adsorption than reduction. Fe⁰ played a dominant role in the PS activation process; reactive species—including HO•, SO₄•⁻, and O₂•⁻—were identified as key agents in subsequent degradation stages. The overall degradation processes comprised three distinct stages: dechlorination, ring-opening, and mineralization. Full article

In the present study three composite materials based on iron in combination with bismuth, copper or lithium carbonates FeNO₃@Li₂CO₃ (SFL), FeNO₃@CuCO₃ (SFC), and FeNO₃@(BiO)₂CO₃ (SFB) were synthesized by coprecipitation. The purpose was to obtain materials that possess targeted adsorbent properties for the recovery of silver ions from aqueous solutions. After synthesis, to emphasize the adsorptive qualities of materials for the recovery of silver ions, the synthesized composite materials, as well as those doped with silver ions following the adsorption process (SFL-Ag, SFC-Ag, and SFB-Ag), were characterized and several adsorption-specific parameters were examined, including temperature, contact time, pH, adsorbent dose, and the initial concentration of silver ions in solution. Subsequently, the ideal adsorption conditions were determined to be as follows: pH > 4, contact time 60 min, temperature 298 K, and solid–liquid ratio (S–L) of 0.1 g of adsorbent to 25 mL of Ag (I) solution for all three materials. The Langmuir model properly fits the experimental equilibrium data of the adsorption process; however, the Ho–McKay model closely represents the adsorption kinetics. The maximum adsorption capacities of the materials, 19.7 mg Ag(I)/g for SFC, 19.3 mg Ag(I)/g for SFB, and 19.9 mg Ag(I)/g for SFL, are comparable. The adsorption mechanism is physical in nature, as evidenced by the activation energies of 1.6 kJ/mol for SFC, 4.15 kJ/mol for SFB, and 1.32 kJ/mol for SFL. The highest Ag(I) concentration used for doping all three materials in the study was 150 mg Ag(I)/L. The process is endothermic, spontaneous, and takes place at the interface between the adsorbent and the adsorbate, according to thermodynamic theory. Subsequently, the antimicrobial activity against Staphylococcus aureus, Escherichia coli, Pseudomonas aeruginosa, and Candida albicans microorganisms was evaluated by rate of inhibition assessment. The SFC-Ag material showed a percentage of 100% inhibition with respect to the positive control for each microorganism. All synthetized materials have better efficiency as antifungal agents. Full article

The vibration properties of materials play a role in their conduction of electric charges. Ionic conductors such as electrodes and solid electrolytes are also relevant in this respect. The vibration properties are typically assessed with infrared and Raman spectroscopy, and inelastic neutron scattering, which all allow for the derivation of the phonon density of states (PDOS) in part of a full portion of the Brioullin zone. Nuclear resonant vibration spectroscopy (NRVS) is a novel method that produces the element-specific PDOS from Mössbauer-active isotopes in a compound. We employed NRVS operando on a pouch cell battery containing a Li⁵⁷FePO₄ electrode, and thus could derive the PDOS of the ⁵⁷Fe in the electrode during charging and discharging. The spectra reveal reversible vibrational changes associated with the two-phase conversion between LiFePO₄ and FePO₄, as well as signatures of metastable intermediate states. We demonstrate how the NRVS data can be used to tune the atomistic simulations to accurately reconstruct the full vibration structures of the battery materials in operando conditions. Unlike optical techniques, NRVS provides bulk-sensitive, element-specific access to the full phonon spectrum under realistic operando conditions. These results establish NRVS as a powerful method to probe lattice dynamics in working batteries and to advance the understanding of ion transport and phase transformation mechanisms in electrode materials. Full article

Lithium iron phosphate (LFP) batteries have become a popular choice for energy storage, electrified mobility, and plants. All lithium-based batteries produce flammable vent gas as a result of failure through thermal runaway. LFP cells produce less gas by volume than nickel-based cells, but the composition of this gas most often contains less carbon dioxide and more hydrogen. However, when LFP cells fail, they generate lower temperatures, so the vent gas is rarely ignited. Therefore, the hazard presented by a LFP cell in thermal runaway is less of a direct battery fire hazard but more of a flammable gas source hazard. This research identified the constituents and components of the vent gas for different sized LFP prismatic cells when overcharged to failure. This data was used to calculate the maximum homogenous concentration of gas that would be released into a 1.73 m³ test rig and the percentage of the lower explosive limit (LEL). Overcharge experiments were conducted using the same type of cells in the test rig in the presence of remote ignition sources. Ignition and deflagration of the vent gas were possible at concentrations below the theoretical LEL of the vent gas if it was homogeneously mixed. Full article

Background: The rapid emergence of antibiotic resistance in Acinetobacter baumannii has led the World Health Organization (WHO) to designate it as a “high priority” pathogen. The emergence of multidrug-resistant (MDR) and pandrug-resistant (PDR) strains poses considerable treatment challenges. As antimicrobial resistance (AMR) escalates toward a post-antibiotic era, innovative therapeutic solutions are urgently needed. Objectives: To clone, over-express, and characterize a novel endolysin, LysTAC1, from Acinetobacter phage TAC1 for its antibacterial efficacy against multidrug-resistant bacteria. Methods: A 24 kDa endolysin featuring a glycoside hydrolase Family 19 chitinase domain was tested against carbapenem-resistant Acinetobacter baumannii clinical isolates and various Escherichia coli strains following outer membrane permeabilization with Ethylenediaminetetraacetic acid (EDTA). Stability assays and molecular docking studies were performed. Results: LysTAC1 demonstrated potent lytic activity against Gram-negative bacteria but showed no activity against Gram-positive bacteria (Staphylococcus aureus ATCC 29213 and Enterococcus gallinarum HCD 28-1). LysTAC1 maintained activity across pH 6–9 and temperatures 4–65 °C, with differential sensitivity to metal ions where K⁺ showed no inhibitory effect at any concentration (0.1–100 mM), and Fe²⁺ was non-inhibitory at lower concentrations (0.1–1 mM), while Mg²⁺ and Ca²⁺ demonstrated concentration-dependent inhibition across the tested range (0.1–100 mM). Molecular docking revealed LysTAC1 interactions with chitinase substrates 4-nitrophenyl N-acetyl-β-D-glucosaminide and 4-nitrophenyl N, N-Diacetyl-β-D-chitobioside, with binding energies of −5.82 and −6.85 kcal/mol, respectively. Conclusions: LysTAC1 shows significant potential as a targeted therapeutic agent against A. baumannii with robust stability under physiological conditions. Full article