Search Results (5)

Limestone calcined clay cement (LC3), enhanced through reactions with volcanic ash and the interaction between limestone and clay, significantly improves the performance of cementitious materials. It has the potential to cut CO₂ emissions by up to 30% and energy consumption in cement manufacture by 15% to 20%, providing a promising prospect for the large-scale production of low-carbon cement with a lower environmental effect. To effectively manufacture LC3 concrete, this study utilized limestone (15%), calcined clay (30%), and gypsum (5%) as supplementary cementitious materials (SCMs), replacing 50% of ordinary Portland cement (OPC). However, in regions abundant in sulfate, sulfate attack can cause interior cracking of concrete, reducing the longevity of the building. To address this issue, microcapsules containing microcrystalline wax, ceresine wax, and nano-CaCO₃ encapsulated in epoxy resin were prepared and successfully incorporated into LC3 concrete. Sulfate resistance tests were conducted through sulfate dry–wet cycles, comparing samples with and without microcapsules. The findings revealed that the initial mechanical and permeability properties of LC3 concrete did not significantly differ from OPC concrete. LC3 concrete with added microcapsules (SP4) exhibited enhanced resistance to sulfate attack, reducing mass loss and compressive strength degradation. SEM images displayed a mesh-like structure of repair products in SP4. After 14 days of self-repair, SP4 exhibited a 44.2% harmful pore ratio, 98.1% compressive strength retention, 88.7% chloride ion diffusion coefficient retention, 91.12 mV maximum amplitude, and 9.14 mV maximum frequency amplitude. The experimental results indicate that the presence of microcapsules enhances the sulfate attack self-healing performance of LC3 concrete. Full article

When treating historical beeswax seals, it seems a natural choice to use materials as similar to the original as possible. The properties of analogous recent materials, however, differ from those of the aged ones, not to mention the fact that the exact composition of the particular sealing wax is usually uncertain. In order to obtain the material of desired properties, recent beeswax is often combined with various additives, including petroleum waxes, or even replaced by mixtures based solely on these products. Within this study, the relevant properties of Permulgin 3274, a ceresin-type wax, were compared with the characteristics of recent and historical beeswaxes. The aim was to evaluate its advantages and limitations, in terms of its possible use for the conservation of beeswax seals. The properties studied were comprised of the chemical composition, thermal properties, mechanical properties, possibilities of colour adjustment and ageing properties. Permulgin 3274′s workability was evaluated by conservators from the National Archives in Prague. The results indicate that, from the technological point of view, Permulgin 3274 could be considered a welcome alternative to the use of traditional conservation mixtures. Full article

As an intelligent material, microcapsules can efficiently self-heal internal microcracks and microdefects formed in cement-based materials during service and improve their durability. In this paper, microcapsules of nano-CaCO₃/ceresine wax composite shell encapsulated with E-44 epoxy resin were prepared via the melt condensation method. The core content, compactness, particle size distribution, morphologies, chemical structure and micromechanical properties of microcapsules were characterized. The results showed that the encapsulation ability, mechanical properties and compactness of microcapsules were further improved by adding nano-CaCO₃ to ceresine wax. The core content, elastic modulus, hardness and weight loss rate (60 days) of nano-CaCO₃/ceresine wax composite shell microcapsules (WM2) were 80.6%, 2.02 GPA, 72.54 MPa and 1.6%, respectively. SEM showed that WM2 was regularly spherical with a rough surface and sufficient space inside the microcapsules to store the healing agent. The incorporation of WM2 to mortar can greatly improve the self-healing ability of mortar after pre-damage. After 14 days of self-healing, the compressive strength recovery rate, proportion of harmful pores and chloride ion diffusion coefficient recovery rate increased to 90.1%, 45.54% and 79.8%, respectively. In addition, WM2 also has good self-healing ability for mortar surface cracks, and cracks with initial width of less than 0.35 mm on the mortar surface can completely self-heal within 3 days. Full article

This research was focused on the analysis of material composition and organic residues present in three molds found in the Moravian region (Czech Republic) belonging to the Roman era. X-ray fluorescence spectroscopy pointed out the possible remelting of Roman objects in Barbarian territory. The analysis of organic residues retrieved from the internal part of mold #2 by pyrolysis-gas chromatography/mass spectrometry proved the presence of ozokerite wax (“earth wax”). Consequent analysis of this organic residue by Atmospheric Solids Analysis Probe–ion mobility spectrometry–high-resolution mass spectrometry (ASAP-IMS-HRMS) confirmed the presence of ceresin, the main component of ozokerite. Ceresin was also detected in a sample of the organic residue from mold #1. Note that this is the first application of ASAP-IMS-HRMS in archaeological research. The remains of earth wax in molds suggest the production of wax models as an intermediate stage for the production of lost-wax ceramic casting molds. Full article

The removal of hydrophobic materials from a porous support, such as wax stains on wall paintings, is particularly challenging. In this context, traditional methods display several drawbacks. The limitations of these methods can be overcome by amphiphile-based aqueous nanostructured fluids, such as micellar solutions and microemulsions. In this study, a microemulsion for the removal of wax spots from artistic surfaces was formulated. The nanostructured fluid includes a non-ionic surfactant, i.e., Triton X-100, and two apolar solvents, namely p-xylene and n-nonane. The solvents were selected on the basis of solubility tests of three waxes in several organic solvents. The nanostructured fluid was characterized by means of small-angle X-rays scattering (SAXS) and the information about micelle structure was used to understand the interaction between the microemulsion and the selected waxes. The microemulsion was then tested during the restoration of the frescoes in the Major Chapel of the Santa Croce Basilica in Florence, Italy. After some preliminary tests on fresco mockups reproduced in the laboratory, the nanostructured fluid was successfully used to clean some wax deposits from the real paintings, hardly removable with traditional physico-mechanical methods. Full article