Search Results (1,159)

In recent decades, pollutant emissions from the combustion of fossil fuels have become increasingly serious for the environment. The present paper reports experimental results for research carried out under laboratory conditions for a Selective Catalytic Reduction (SCR) system, implemented in different configurations on an ISUZU 4JB1 diesel engine. The obtained results allow for a comparative analysis of NOx formation as a function of diesel engine load (χ = 25–100%), at 1350, 2100, 2850, and 3600 rpm, with the engine operating under either cold (T < 343 K) or warm (T > 343 K) regimes. A preheating system for AdBlue droplets, in the form of a metal honeycomb that uses electromagnetic induction and incorporates a high-frequency generator, was introduced in the flow path of the combustion gases and tested to compare the experimental results. This system enabled temperatures of up to 643 K. A magneto-strictive system was also introduced in the SCR structure to atomize the AdBlue droplets to a minimum diameter of 3.5 μm. Using this principle, combined with preheating, the effect of calefaction was compared with the classical case of the internal heating of the SCR catalyst. For experimental purposes, piezoelectric cells dedicated to the transformation of the AdBlue solution into micro- or nano-droplets, which were entrained into the SCR by an ejector, were also used. Experimental results are presented in graphical form and reveal that the use of preheating, heating, or piezoelectric cells leads to improved NOx conversion. The tested solutions showed reductions in NOx emissions of up to eight times depending on the diesel engine load, demonstrating their strong impact on NOx reduction. Full article

The heat shock protein 70 (Hsp70) family mediates responses to environmental stress in insects. The wheat midge Sitodiplosis mosellana, a worldwide pest, avoids summer and winter temperature extremes by diapause of the third-instar larvae in the soil. To explore the functions of Hsp70s in this process, we characterized two cytoplasmic Hsp70 genes (SmHsp70A1-1 and SmHsp70A1-2) from this insect. Both SmHsp70s contained three signature motifs of the family and lacked introns. Developmental expression profiling revealed maximal SmHsp70A1-1 expression during early larval stages, while the expression of SmHsp70A1-2 was highest in the pupal stages. The expression of SmHsp70A1-1 was significantly upregulated during diapause, particularly during summer and winter, whereas SmHsp70A1-2 showed marked downregulation and dose-dependent induction by 20-hydroxyecdysone (20E). Furthermore, both genes exhibited similar expression patterns in over-summering and over-wintering larvae under thermal stress, with maximal expression at 40 °C and −10 °C, respectively, but were not significantly induced at prolonged extreme temperatures (50 °C or −15 °C). Knockdown of the two SmHsp70 genes by RNA interference (RNAi) significantly increased the susceptibility of the larvae to cold stress. These results suggest the important role of both SmHsp70 genes in diapause-associated stress tolerance and provide crucial insights into the mechanisms underlying thermal adaptation in S. mosellana. Full article

This study focuses on the detailed investigation of the eutectic Aluminium Silicon (Al-12.6 wt% Si) alloy, which was solidified without and with a 10 mT induction rotating magnetic field (RMF). The experiments were conducted as part of the MICAST Hungary project, as the mirror experiments were solidified in the Solidification and Quenching Furnace (SQF) at the International Space Station (ISS). The mirror samples were solidified using solidification parameters similar to the ISS experiments. This study examined the meso-structure of the samples and the eutectic microstructure in both stirred (RMF-applied) and non-stirred (RMF-free) samples. Special attention was given to the influence of magnetic stirring on key microstructural features, such as the eutectic lamellae distance, the length of the lamellae, and the spatial orientation of the lamellae were investigated. Measuring and analysing these parameters gives us an overall picture of the microstructure of the eutectics. The 10 mT low-intensity RMF used in the experiment has a demonstrable effect on the formation of the eutectic structure; short aluminium dendrites concentrate at both edges of the stirred sample, and their proportion decreases as the sample approaches its end. In contrast, in the non-stirred sample, long, elongated Al dendrites solidify parallel to the direction of heat removal, and their proportion and size continuously increase as the sample progresses. Furthermore, a possible relationship was found between the decrease in the eutectic lamella length and the lamellae’s average distance. Full article

The induction quenching–tempering process typically enhances the surface strength and core toughness of alloy steels by utilizing the skin effect. However, the impact of parameters like quenching current and heating time on the microstructure and mechanical property of 34CrNiMo6 steel crankshafts remains unclear. In this work, the microstructure of 34CrNiMo6 steel after induction quenching exhibits three distinct zones: a martensite hardened layer; a transition zone of martensite and tempered sorbite; and a matrix of tempered sorbite. As the induction current (400, 500, and 600 mA) and heating time (3, 5, and 7 s) increase, the hardened layer thickness enhances (up to 3.21 mm). Under the 600 mA and 7 s, the hardened layer reaches peak hardness and residual stress values of 521.48 HV and −330.12 MPa, showing a decreasing trend from surface to core. After tempering at 330 °C for 2 h, the hardened layer mainly consists of tempered martensite, and the surface hardness and residual stress decrease to 417.94 HV and −12.33 MPa. The temperature gradient from quenching balances after tempering, with martensitic phase transformation and stress redistribution reducing hardness and residual stress. Furthermore, the induction quenching–tempering process enhances the toughness of 34CrNiMo6 steel when compared to the untreated specimen, boosting its tensile yield strength, elongation, and tensile strength by 15.3%, 14.9%, and 19.5%, respectively. This work deepens the understanding of induction quenching–tempering process and provides valuable insights for designing alloy steels with excellent mechanical properties. Full article

The vaporization of urea–water solution (AdBlue) plays a critical role in the performance of selective catalytic reduction (SCR) systems for modern diesel engines. This study presents mathematical models describing the vaporization of AdBlue droplets under ultrasonic excitation generated by a magnetostrictive effect, focusing on both film and volumetric regimes. The models rigorously incorporate heat and mass transfer equations, including acoustic cavitation effects induced by ultrasound. The influence of magnetostrictive-induced atomization and combined inductive preheating on droplet detachment and SCR catalyst efficiency was analyzed. Additionally, the impact of ultrasound frequency and amplitude on thermal vaporization efficiency and reactive mixture formation was investigated with the aim of enhancing NOx emission reduction. Model validation against literature data confirmed the practical applicability of the proposed approach, offering valuable insights for optimizing ultrasound-assisted AdBlue injection systems. Full article

Hydrate-based CO₂ sequestration is considered one of the most promising methods in the field of carbon capture, utilization, and storage. The abundant fractured environments in marine sediments provide an ideal setting for the sequestration of CO₂ hydrate. Investigating the kinetics and morphological characteristics of CO₂ hydrate formation within fractures is a critical prerequisite for achieving efficient and safe CO₂ sequestration using hydrate technology in subsea environments. Based on the aforementioned considerations, the kinetic experiments on the formation, dissociation, and reformation of CO₂ hydrates were conducted using a high-pressure visualization experimental system in this study. The kinetic behaviors and morphological characteristics of CO₂ hydrates within sandstone fractures were comprehensively investigated. Particular emphasis was placed on analyzing the effects of fracture width, type, and surface roughness on the processes of hydrate formation, dissociation, and reformation. The experimental results indicate the following: (1) At a formation pressure of 2.9 MPa, the 10 mm width fracture exhibited the shortest induction time, the longest formation duration, and the highest hydrate yield (approximately 0.52 mol) compared to the other two fracture widths. The formed CO₂ hydrates exhibited a smooth, thin-walled morphology. (2) In X-type fractures, the formation of CO₂ hydrates was characterized by concurrent induction and dissolution processes. Compared to I-type fractures, the hydrate formation process in X-type fractures exhibited shorter formation durations and generally lower hydrate yields. (3) An increase in fracture roughness enhances the number of nucleation sites for the formation of hydrates. In both fracture types (I-type and X-type), the induction time for CO₂ hydrate formation was nearly negligible. However, a significant difference in the trend of formation duration was observed under varying roughness conditions. (4) Hydrate dissociation follows a diffusion-controlled mechanism, progressing from the fracture walls towards the interior. The maximum gas production was achieved in the 10 mm-width fracture, reaching 0.24 mol, indicating optimal heat and mass transfer conditions under this configuration. (5) During the reformation process, the induction time was significantly shortened due to the “memory effect.” However, the hydrate yield after the reformation process remained consistently lower than that of the first formation, which is primarily attributed to the high solubility of CO₂ in the aqueous phase. Full article

Conidiation and stress tolerance are pivotal traits in entomopathogenic fungi, critically influencing their production costs and environmental tolerance. While the transcription factor high-mobility group protein (HMG), characterized by a conserved HMG-box domain, has been extensively studied for its role in sexual development, its functions in entomopathogenic fungi remain largely unexplored. This study employed gene knockout to investigate the role of MaHMG in Metarhizium acridum. The deletion of MaHMG delayed conidiation initiation and caused a highly significant 58% reduction in conidial yield versus that of the wild type (WT) after 15 days. Furthermore, the conidiation pattern on microcycle induction medium (SYA) shifted from microcycle to normal conidiation. The ΔMaHMG mutant exhibited decreased conidial germination rates and markedly reduced tolerance following UV-B irradiation and heat-shock treatments, alongside increased sensitivity to the cell wall perturbant calcofluor white (CFW). RNA-seq analysis during this conidiation shift identified 88 differentially expressed genes (DEGs), with functional annotation implicating their predominant association with hyphal development, cell wall biogenesis, cell cycle progression, and conidiation. In conclusion, MaHMG functions as a critical positive regulator governing both conidiation and stress tolerance in M. acridum, underscoring its fundamental role in fungal biology and potential as a target for enhancing biocontrol agent performance. Full article

Previous studies revealed that low expression of Selenoprotein S (SELS) could enhance osteogenic differentiation, but the underlying mechanisms remain unclear. In this study, we aimed to elucidate the role of SELS and its transcription-factor-based regulatory mechanism during osteogenic differentiation. In comparison with 12-week-old mice, which represent the stage of stable osteogenic differentiation, 3-week-old mice, representing the active ossification stage, showed significantly higher levels of SELS in the mandible. Transcriptomic analysis revealed that SELS is primarily associated with extracellular matrix organization and collagen biosynthesis during mandibular development. In bone marrow mesenchymal stem cells (BMSCs) with SELS knockdown, SP7 levels were elevated after 7 days of osteogenic induction in vitro. Consistently, immunohistochemical and immunofluorescence staining confirmed increased SP7 expression in the mandibles of 7-week-old Sels knockout mice. Dual-luciferase reporter assays and chromatin immunoprecipitation (ChIP) analysis demonstrated that SP7 directly binds to the heat shock protein 47 (HSP47) promoter and negatively regulates its transcription. Consequently, upregulation of SP7 following SELS knockdown led to downregulation of HSP47 and concurrent upregulation of the SP7 downstream targets, collagen type I alpha 1 chain (COL1A1) and Secreted protein acidic and rich in cysteine (SPARC). SELS expression is upregulated during active osteogenesis. Low expression of SELS regulates osteogenic differentiation in a bidirectional and fine-tuned manner through the SP7–HSP47/COL1A1/SPARC axis. Full article

Aiming at the drawback of unstable torque output caused by heat generation due to slip in magnetorheological fluid transmission devices, this paper proposes a new type of non-coaxial conical disk magnetorheological fluid transmission structure and deduces its mathematical model of output torque. The magnetic circuit design was carried out based on the conical disk configuration. The electromagnetic field analysis of the transmission device was conducted by the finite element method, and the influence laws of parameters such as the coil current, magnetic conductive material, the conical angle of the disk, and the working gap on the distribution of the magnetic induction intensity in the working area were obtained. The test system for the non-coaxial conical disk type magnetorheological fluid transmission device was established, and experiments on electromagnetic fields, transmission performance, torque response, etc., were carried out. Research results show that the magnetic induction intensity in the working area increases with the increase of the current in the excitation coil, decreases with the increase of the working gap between the two conical disks, and is positively correlated with the magnetic permeability of the conical disk and the magnetic conducting ring materials. The effective working area range and magnetic induction intensity of the governor both decrease as the conical angle of the disk increases. The magnitude of the magnetic induction intensity on the center line is basically the same, but the effective working area range corresponding to different angles shows significant differences. Full article

Discrete Silicon Carbide Metal-Oxide-Semiconductor Field-Effect Transistors (SiC MOSFETs) are characterized by their lower parasitic parameters and single-chip design, enabling them to achieve even faster switching speeds. However, the rapid rate of change in voltage (dv/dt) and current (di/dt) can lead to overshoot and oscillation in both voltage and current, ultimately limiting the performance of high-frequency operations. To address this issue, this paper presents a high-switching-frequency motor controller that utilizes discrete SiC MOSFETs. To achieve a high switching frequency for the controller while minimizing current oscillation and voltage overshoot, a novel electronic system architecture is proposed. Additionally, a passive driving circuit is designed to suppress gate oscillation without the need for additional control circuits. A new printed circuit board (PCB) laminate stack featuring low parasitic inductance, high current conduction capacity, and efficient heat dissipation is also developed using advanced wiring technology and a specialized heat dissipation structure. Compared to traditional methods, the proposed circuit and bus design features a simpler structure, a higher power density, and achieves a 13% reduction in current overshoot, along with a 15.7% decrease in switching loss. The silicon carbide (SiC) controller developed from this research has successfully undergone double-pulse and power testing. The results indicate that the designed controller can operate reliably over extended periods at a switching frequency of 50 kHz, achieving a maximum efficiency of 98.2% and a power density of 9 kW/kg (10 kW/L). The switching frequency and quality density achieved by the controller have not been observed in previous studies. This controller is suitable for use in the development of new energy electrical systems. Full article

This study investigates the influence of temperature measurement accuracy on tool failure mechanisms in industrial hot forging processes. Challenges related to extreme operational conditions, including high temperatures, limited access to measurement surfaces, and optical interferences, significantly hinder reliable data acquisition. Thermal imaging, pyrometry, thermocouples, and finite element modeling were employed to characterize temperature distributions in forging tools and billets. Analysis of multi-stage forging of stainless steel valve forgings revealed significant discrepancies between induction heater settings and actual billet surface temperatures, measured by thermal imaging. This thermal non-uniformity led to localized underheating and insufficient dissolution of hard inclusions, confirmed by dilatometric tests, resulting in billet jamming and premature tool failure. In slender bolt-type forgings, excessive or improperly controlled billet temperatures increased adhesion between the forging and tool surface, causing process resistance, billet sticking, and accelerated tool degradation. Additional challenges were noted in tool preheating, where non-uniform heating and inaccurate temperature assessment compromised early tool performance. Measurement errors associated with thermal imaging, particularly due to thermal reflections in robotic gripper monitoring, led to overestimated temperatures and overheating of gripping elements, impairing forging manipulation accuracy. The results emphasize that effective temperature measurement management, including cross-validation of methods, is crucial for assessing tool condition, enhancing process reliability, and preventing premature failures in hot forging operations. Full article

In a warming world, mechanisms, such as the heat shock response, which plays a role in the recovery from or tolerance towards heat stress, are of increasing importance. Certain heat shock protein genes (hsps) have previously been shown to be highly inducible in several paper wasp species during high temperature stress under laboratory conditions. Here, we sought to investigate how hsps are expressed under natural daily temperature fluctuations by collecting broods from wild nests of two species of paper wasps (Polistes dominula, P. nimpha). We collected them at 06:00 and 16:00, the expected low and high points in daily hsp expression, and measured the expression of three hsps (hsp70, hsp83, hsc70). We found that the nest temperature in July could reach temperatures that result in a large upregulation of hsp expression in the laboratory. Under natural conditions, however, we found that the induction response was much more moderate and limited to the larvae. The pupae showed no response to the daily fluctuating temperature and had a constant expression similar to that of larvae in the afternoon. The similarities and differences between natural and laboratory hsp expressions highlight the importance of field studies, as they add valuable context when interpreting laboratory results. Full article

This study investigates the thermal performance of induction motors powered by multilevel H-bridge inverters using a novel pulse-width phase shift triangle modulation (PSTM-PWM) technique. Conventional PWM methods introduce significant harmonic distortion, increasing copper and iron losses and causing overheating and reduced motor lifespan. Through experimental testing and comparison with standard PWM techniques (LS-PWM and PS-PWM), the proposed PSTM-PWM reduces harmonic distortion by up to 64% compared to the worst one and internal motor losses by up to 5.5%. A first-order thermal model is used to predict motor temperature, validated with direct thermocouple measurements and infrared thermography. The results also indicate that the PSTM-PWM technique improves thermal performance, particularly at a triangular waveform peak value of 3.5 V, reducing temperature by around 6% and offering a practical and simple solution for industrial motor drive applications. The modulation order was set to M = 7 to reduce both the losses in the power inverter and to prevent the generation of very high voltage pulses (high dV/dt), which can deteriorate the insulation of the induction motor windings over time. Full article

Pitaya (Selenicereus undatus) is a long-day climbing cactus that blooms in waves mostly on 1-year old, succulent leafless shoots called cladodes. Nonetheless, pitaya can also bloom on new-year growth if the buds of the cladodes are mature enough and competent for flower induction. Here, we tested, during two consecutive years, whether early pruning could have a positive effect on promoting more flowering waves, better fruiting, and heavier yield of ‘Korean White’ pitaya cultivated in unheated greenhouses of Southeastern Spain. The results show that pruning in January instead of March did not consistently modify the reproductive behavior of ‘Korean White’ pitaya in our conditions. Therefore, no significant effects on the number of blooming waves, flowering intensity, fruit set, quality or yield were observed. The only positive effect, not always significant, was an increase in fruit size that led to better fruit distribution into commercial categories in one out of the two experimental seasons. The lack of effect of early pruning was attributed to the prevalent low temperatures during winter in Spain. The results, however, suggest it is worthwhile exploring whether greenhouse heating with temperatures above pitaya’s base temperature may have the desired effects on increasing blooming waves. The profitability of this practice have to be carefully assessed. Full article

(1) Background: Polyploid fish are highly important in increasing fish production, improving fish quality, and breeding new varieties. The loach (Misgurnus anguillicaudatus), as a naturally polyploid fish, serves as an ideal biological model for investigating the mechanisms of chromosome doubling; (2) Methods: In this study, tetraploidization in diploid loach was induced by heat shock treatment, and, for the first time, the role of the key cell cycle gene cdk1 (cyclin-dependent kinase 1) in chromosome doubling was investigated; (3) Results: The experimental results show that when eggs are fertilized for 20 min and then subjected to a 4 min heat shock treatment at 39–40 °C, this represents the optimal induction condition, resulting in a tetraploid rate of 44%. Meanwhile, the results of the cdk1 knockout model (2n cdk1^−/−) constructed using CRISPR/Cas9 showed that the absence of cdk1 significantly increased the chromosome doubling efficiency of the loach. The qPCR analysis revealed that knockout of cdk1 significantly upregulated cyclin genes (ccnb3,ccnc, and ccne1), while inhibiting expression of the separase gene espl1 (p < 0.05); (4) Conclusions: During chromosome doubling in diploid loaches induced by heat shock, knocking out the cdk1 gene can increase the tetraploid induction rate. This effect may occur through downregulation of the espl1 gene. This study offers novel insights into optimizing the induced breeding technology of polyploid fish and deciphering its molecular mechanism, while highlighting the potential application of integrating gene editing with physical induction. Full article