Search Results (855)

A multiphase model of hydrothermal liquefaction (HTL) using the computational fluid dynamics coupling discrete element method (CFD-DEM) is used to simulate biocrude oil production from sludge flocs in a continuous stirred tank reactor (CSTR). Additionally, the influence of the agitator speed and the slurry flow rate on dynamic biocrude oil production is investigated through full transient CFD analysis in a scaled-up CSTR study. The kinetics of the HTL mechanism as a function of temperature, pressure, and residence time distribution were employed in the model through a user-defined function (UDF). The multiphysics simulation of the HTL process in a stirred tank reactor using the Lagrangian–Eulerian (LE) approach, along with a standard k-ε turbulence model, integrated HTL kinetics. The simulation accounts for particle–fluid interactions by coupling CFD-derived hydrodynamic fields with discrete particle motion, enabling prediction of individual particle trajectories based on drag, buoyancy, and interphase momentum exchange. The three-phase flow using a compressible non-ideal gas model and multiphase interaction as design requirements increased process efficiency in high-pressure and high-temperature model conditions. Full article

Under elevated loading conditions, the aggregation of fillers emerges as a pivotal factor driving the degradation of separation performance in mixed matrix membranes. The two-dimensional (2D) modification of fillers, aimed at enhancing interfacial contact with polymers, has been recognized as an effective strategy to improve interphase compatibility and increase filler loading capacity. However, it is worth noting that the BET surface area of 2D fillers is typically relatively low. In this study, a two-step approach was developed. First, a “diffusion-mediated” process was combined with a solvent optimization strategy based on first-principles (DFT) calculations, achieving a 20-fold suppression in ZIF-67 nucleation-crystallization rate. This enabled the successful synthesis of a 2D amorphous nanoflower structure. Subsequently, the processing parameters were fine-tuned to enhance the specific surface area of ZIF-67 to 403 m²/g while preserving its 2D structural integrity. Ultimately, the as-prepared 2D ZIF-67 was incorporated into a hydrogenated styrene-butadiene block copolymer (SEBS) matrix to fabricate a mixed matrix membrane. Remarkably, at a filler loading of 20 wt%, the CH₄ permeability coefficient increased significantly from 11.7 barrer to 35.3 barrer, while the CH₄/N₂ selectivity was maintained at 3.21, indicating minimal interfacial defects and demonstrating the feasibility and effectiveness of the proposed methodology. Full article

The solid electrolyte interphase (SEI) is a passive layer, typically a few hundred angstroms thick, that forms on the electrode surface in the first few battery cycles when the electrode is in contact with the electrolyte in lithium-metal batteries. Composed of a combination of lithium salts and organic compounds, the SEI plays a critical role in battery performance, serving as a channel for Li-ion shuttling. Its structure typically comprises an inorganic component-rich sublayer near the electrode and an outer organic component-rich sublayer. Understanding heat transport through the SEI is crucial for improving battery pack safety, particularly since the Li-ion diffusion coefficient exhibits an exponential temperature dependence. This study employs first-principles calculations to investigate phonon-mediated temperature-dependent lattice thermal conductivity across the inorganic components of the SEI, including, LiF, Li₂O, Li₂S, Li₂CO₃, and LiOH. This study is also extended to the dependence of the grain size on thermal conductivity, considering the mosaic-structured nature of the SEI. Full article

Background: High-risk chromosomal abnormalities (HRCAs) detected by fluorescence in situ hybridization (FISH) have a well-established adverse prognostic impact in multiple myeloma (MM). It is increasingly recognized that the coexistence of two or more HRCAs identifies a particularly poor-risk subgroup, often referred to as double- or multiple-hit MM. However, there is currently no consensus on its definition. Methods: We retrospectively analyzed a multicenter cohort of 1122 newly diagnosed MM patients from 2008 to 2019. Double-hit MM was defined as the coexistence of at least two of the following four HRCAs: t(14;16), gain(1q), del(17p), and del(1p). Based on this definition, we constructed a novel prognostic model, the HBDH (Institute of Hematology & Blood Diseases Hospital) double-hit model, and assessed its prognostic value for progression-free survival (PFS) and overall survival (OS). Results: According to the HBDH model, double-hit patients showed significantly inferior outcomes compared to non-double-hit patients, with median PFS of 20.6 vs. 53.3 months (p < 0.001) and median OS of 40.2 vs. 84.2 months (p < 0.001). The addition of del(13q), t(4;14), or t(11;14) did not improve the prognostic performance of the model. Importantly, the HBDH model was independent of the International Staging System (ISS), elevated LDH, and advanced age. Conclusions: The HBDH double-hit model identifies a subset of ultra-high-risk MM patients carrying at least two major HRCAs, providing a simple and robust framework for prognostic stratification and a potential reference for future biologically driven treatment approaches. Full article

Growing evidence suggests that Reelin signals and cleavages are affected in neurodegenerative diseases, prospecting a potential role for Reelin in the pathogenesis of neurodegenerative processes occurring in insulted retinas. We sought to determine whether Reelin, Aβ1-42, FTH1 and TAU proteins accumulate in ocular fluids of idiopathic epiretinal membrane (iERM) specimens and whether such accumulations depend on disease severity. Comparisons and correlation studies were used to verify the hypothesis of a Reelin, Aβ1-42, TAU and FTH1 marker expressions in this vitreoretinal disease, extending the knowledge on the pathological spectrum of neurodegenerative eye diseases. Aqueous, vitreous and peeled-off ERM samples were collected from patients who had undergone vitrectomy and grouped according to disease severity. We found out that Reelin and Aβ1-42 were expressed in ocular fluids and affected ERMs depending on disease severity. At stage 3, higher Reelin and Aβ1-42 immunofluorescence staining was detected in ERMs, in agreement with the higher Reelin, Aβ1-42, FTH1 and TAU transcript expressions by RT-PCR. Differential expressions of transcripts specific to Aβ1-42, FTH1, GFAP and TAU occurred in vitreal hyalocytes and astrocytes, which selectively responded to vitreal exposure. This is the first study reporting the association between Reelin and ERM disease, highlighting the potential role of Reelin in neurodegenerating and Drusen-affected retinas. The potential association of neurodegenerative mediators with ERM would suggest that part of the neuronal damage activated at the vitreoretinal interphase might be driven by Reelin. Full article

Lithium-ion batteries (LIBs) have attracted extensive attention as a distinguished electrochemical energy storage system due to their high energy density and long cycle life. However, the initial irreversible lithium loss during the first cycle caused by the formation of the solid electrolyte interphase (SEI) leads to the prominent reduction in the energy density of LIBs. Notably, lithium formate (HCOOLi, LFM) is regarded as a promising cathode prelithiation reagent for effective lithium supplementation due to its high theoretical capacity of 515 mAh·g⁻¹. Nevertheless, the stable Li-O bond of LFM brings out the high reaction barrier accompanied by the high decomposition potential, which impedes its practical applications. To address this issue, a feasible strategy for reducing the reaction barrier has been proposed, in which the decomposition potential of LFM from 4.84 V to 4.23 V resulted from the synergetic effects of improving the electron/ion transport kinetics and catalysis of transition metal oxides. The addition of LFM to full cells consisting of graphite anodes and LiNi_0.834Co_0.11Mn_0.056O₂ cathodes significantly enhanced the electrochemical performance, increasing the reversible discharge capacity from 156 to 169 mAh·g⁻¹ at 0.1 C (2.65–4.25 V). Remarkably, the capacity retention after 100 cycles improved from 72.8% to 94.7%. Our strategy effectively enables LFM to serve as an efficient prelithiation additive for commercial cathode materials. Full article

Solid-state lithium batteries (SSLBs) have emerged as a promising alternative to conventional lithium-ion systems due to their superior safety profile, higher energy density, and potential compatibility with lithium metal anodes. However, a major challenge hindering their widespread deployment is the formation and growth of lithium dendrites, which compromise both performance and safety. This review provides a comprehensive and structured overview of recent advances in dendrite suppression strategies, with special emphasis on the role played by the nature of the solid electrolyte. In particular, we examine suppression mechanisms and material innovations within the three main classes of solid electrolytes: sulfide-based, oxide-based, and polymer-based systems. Each electrolyte class presents distinct advantages and challenges in relation to dendrite behavior. Sulfide electrolytes, known for their high ionic conductivity and good interfacial wettability, suffer from poor mechanical strength and chemical instability. Oxide electrolytes exhibit excellent electrochemical stability and mechanical rigidity but often face high interfacial resistance. Polymer electrolytes, while mechanically flexible and easy to process, generally have lower ionic conductivity and limited thermal stability. This review discusses how these intrinsic properties influence dendrite nucleation and propagation, including the role of interfacial stress, grain boundaries, void formation, and electrochemical heterogeneity. To mitigate dendrite formation, we explore a variety of strategies including interfacial engineering (e.g., the use of artificial interlayers, surface coatings, and chemical additives), mechanical reinforcement (e.g., incorporation of nanostructured or gradient architectures, pressure modulation, and self-healing materials), and modifications of the solid electrolyte and electrode structure. Additionally, we highlight the critical role of advanced characterization techniques—such as in situ electron microscopy, synchrotron-based X-ray diffraction, vibrational spectroscopy, and nuclear magnetic resonance (NMR)—for elucidating dendrite formation mechanisms and evaluating the effectiveness of suppression strategies in real time. By integrating recent experimental and theoretical insights across multiple disciplines, this review identifies key limitations in current approaches and outlines emerging research directions. These include the design of multifunctional interphases, hybrid electrolytes, and real-time diagnostic tools aimed at enabling the development of reliable, scalable, and dendrite-free SSLBs suitable for practical applications in next-generation energy storage. Full article

One of the advantages of the EPR spectroscopy method in assessing structural defects caused by irradiation is the fact that using this method it is possible to determine not only the concentration dependences of the defect structure but to also establish their type, which is not possible with methods such as X-ray diffraction or scanning electron microscopy. Based on the data obtained, the role of variation in the ratio of components in Li₄SiO₄–Li₂TiO₃ ceramics on the processes of softening under high-dose irradiation with protons simulating the accumulation of hydrogen in the damaged layer, as well as the concentration of structural defects in the form of oxygen vacancies and radiolysis products on the processes of high-temperature degradation of ceramics, was determined. It was found that the main changes in the defect structure during the prolonged thermal exposure of irradiated samples are associated with the accumulation of oxygen vacancies, the density of which was estimated by the change in the intensity of singlet lithium, characterizing the presence of E-centers. At the same time, it was found that the formation of interphase boundaries in the structure of Li₄SiO₄–Li₂TiO₃ ceramics leads to the inhibition of high-temperature degradation processes in the case of post-radiation thermal exposure for a long time. Also, during the conducted studies, the role of thermal effects on the structural damage accumulation rate in Li₄SiO₄–Li₂TiO₃ ceramics was determined in the case when irradiation is carried out at different temperatures. During the experiments, it was determined that the main contribution of thermal action in the process of proton irradiation at a fluence of 5 × 10¹⁷ proton/cm² is an increase in the concentration of radiolysis products, described by changes in the intensities of spectral maxima, characterized by the presence of defects such as ≡Si–O, SiO₄³⁻ and Ti³⁺ defects. Full article

Many speech coding strategies have been developed over the years, but comparing them has been convoluted due to the difficulty in disentangling brand-specific and patient-specific factors from strategy-specific factors that contribute to speech understanding. Here, we present a comparison with a ‘virtual’ patient, by comparing two strategies from two different manufacturers, Advanced Combination Encoder (ACE) versus HiResolution Fidelity 120 (F120), running on two different implant systems in a computational model with the same anatomy and neural properties. We fitted both strategies to an expected T-level and C- or M-level based on the spike rate for each electrode contact’s allocated frequency (center electrode frequency) of the respective array. This paper highlights neural and electrical differences due to brand-specific characteristics such as pulse rate/channel, recruitment of adjacent electrodes, and presence of subthreshold pulses or interphase gaps. These differences lead to considerably different recruitment patterns of nerve fibers, while achieving the same total spike rates, i.e., loudness percepts. Also, loudness growth curves differ significantly between brands. The model is able to demonstrate considerable electrical and neural differences in the way loudness growth is achieved in CIs from different manufacturers. Full article

In this work, graphite anodes and lithium iron phosphate (LFP) cathodes are used to examine the effects of sodium hexafluorophosphate (NaPF₆) and potassium hexafluorophosphate (KPF₆) electrolyte additives on the formation of the solid electrolyte interphase and the performance of lithium-ion batteries in both half-cell and full-cell designs. The objective is to assess whether these additives may increase cycle performance, decrease irreversible capacity loss, and improve interfacial stability. Compared to the control electrolyte (1.22 M Lithium hexafluorophosphate (LiPF₆)), cells with NaPF₆ and KPF₆ additives produced less SEI products, which decreased irreversible capacity loss and enhanced initial coulombic efficiency. Following the formation of the solid electrolyte interphase, the specific capacity of the control cell was 607 mA·h/g, with 177 mA·h/g irreversible capacity loss. In contrast, irreversible capacity loss was reduced by 38.98% and 37.85% in cells containing KPF₆ and NaPF₆ additives, respectively. In full cell cycling, a considerable improvement in capacity retention was achieved by adding NaPF₆ and KPF₆. The electrolyte, including NaPF₆, maintained 67.39% greater capacity than the LiPF₆ baseline after 20 cycles, whereas the electrolyte with KPF₆ demonstrated a 30.43% improvement, indicating the positive impacts of these additions. X-ray photoelectron spectroscopy verified that sodium (Na⁺) and potassium (K⁺) ions were present in the SEI of samples containing NaPF₆ and KPF₆. While K⁺ did not intercalate in LFP, cyclic voltammetry confirmed that Na⁺ intercalated into LFP with negligible impact on the energy storage of full cells. These findings demonstrate that NaPF₆ and KPF₆ are suitable additions for enhancing lithium-ion battery performance in the popular artificial graphite/LFP system. Full article

Botulinum neurotoxins (BoNTs) are known to inhibit synaptic transmission by targeting SNARE proteins, but their selectivity toward central excitatory and inhibitory pathways is not yet fully understood. In this study, the interaction of serotypes A (BoNT/A) and B (BoNT/B) with the glutamatergic and GABAergic systems has been investigated using a pharmacological approach in an animal model of inflammatory pain, i.e., the formalin test in mice. BoNTs were administered intracerebroventricularly, three days before testing, followed 15 min before testing by systemic administration of sub-analgesic doses of MK801, an NMDA receptor antagonist, or muscimol, a GABA_A receptor agonist. BoNT/A reduced the second phase of the formalin test without affecting both the first phase and the interphase, suggesting a selective action on excitatory glutamatergic circuits while sparing GABAergic inhibition. Co-administration of MK801 with BoNT/A did not enhance analgesia, and muscimol did not further reduce interphase, confirming preserved GABAergic transmission. In contrast, BoNT/B abolished the interphase, consistent with impaired GABA release. Co-administration of MK801 or muscimol with BoNT/B restored the interphase, indicating compensatory rebalancing of excitatory-inhibitory networks. These results demonstrate that BoNT/A and BoNT/B exert distinct effects on central neurotransmission and support the hypothesis that BoNT/A preferentially targets excitatory synapses, while BoNT/B targets inhibitory synapses. This work contributes to a deeper understanding of anti-inflammatory mechanisms of BoNTs and their selective interaction with central pain pathways. Full article

The remarkable advantages of zinc anodes render aqueous zinc-ion batteries (ZIBs) a highly promising energy storage solution. Nevertheless, the uncontrolled growth of zinc dendrites and side reactions pose significant obstacles to the practical application of ZIBs. To address these issues, a straightforward strategy has been proposed, involving the addition of a minute quantity of AgNO₃ to the electrolyte to stabilize zinc anodes. This additive spontaneously forms a hierarchically porous Ag interphase on the zinc anodes, which is characterized by its zinc-affinitive nature. The interphase offers abundant zinc nucleation sites and accommodation space, leading to uniform zinc plating/stripping and enhanced kinetics of zinc deposition/dissolution. Moreover, the chemically inert Ag interphase effectively curtails side reactions by isolating water molecules. Consequently, the incorporation of AgNO₃ enables zinc anodes to undergo cycling for extended periods, such as over 4000 h at a current density of 0.5 mA/cm² with a capacity of 0.5 mAh/cm², and for 450 h at 2 mA/cm² with a capacity of 2 mAh/cm². Full zinc-ion cells equipped with this additive not only demonstrate increased specific capacities but also exhibit significantly improved cycle stability. This research presents a cost-effective and practical approach for the development of reliable zinc anodes for ZIBs. Full article

Nearly four decades have passed since fluorescence in situ hybridisation was first applied in plants to support molecular cytogenetic analyses across a wide range of species. Subsequent advances in DNA sequencing, bioinformatic analysis, and microscopy, together with the immunolocalisation of various nuclear components, have provided unprecedented insights into the cytomolecular organisation of the nuclear genome in both model and non-model plants, with crop species being perhaps the most significant. The ready availability of sequenced genomes is now facilitating the application of state-of-the-art cytomolecular techniques across diverse plant species. However, these same advances in genomics also pose a challenge to the future of plant molecular cytogenetics, as DNA sequence analysis is increasingly perceived as offering comparable insights into genome organisation. This perception persists despite the continued relevance of FISH-based approaches for the physical anchoring of genome assemblies to chromosomes. Furthermore, cytogenetic approaches cannot currently rival purely genomic methods in terms of throughput, standardisation, and automation. This review highlights the latest key topics in plant cytomolecular research, with particular emphasis on chromosome identification and karyotype evolution, chromatin and interphase nuclear organisation, chromosome structure, hybridisation and polyploidy, and cytogenetics-assisted crop improvement. In doing so, it underscores the distinctive contributions that cytogenetic techniques continue to offer in genomic research. Additionally, we critically assess future directions and emerging opportunities in the field, including those related to CRISPR/Cas-based live-cell imaging and chromosome engineering, as well as AI-assisted image analysis and karyotyping. Full article

The solid electrolyte interphase (SEI) on the anode of lithium-ion batteries (LIBs) has been studied thoroughly due to its crucial importance to the battery’s long-term performance. At the same time, most studies of the SEI apply ex situ characterization methods, which may introduce artifacts or misinterpretations as they do not investigate the SEI in its unaltered state immersed in liquid battery electrolyte. Thus, in this work, we focus on using the non-destructive combination of electrochemical quartz crystal microbalance with dissipation monitoring (EQCM-D) and impedance spectroscopy (EIS) in the same electrochemical cell. EQCM-D can not only probe the solidified products of the SEI but also allows for the monitoring of viscoelastic layers and viscosity changes of the electrolyte at the interphase during the SEI formation. EIS complements those results by providing electrochemical properties of the formed interphase. Our results highlight substantial differences in the physical and electrochemical properties between the SEI formed on copper and on amorphous carbon and show how formation parameters and the additive vinylene carbonate (VC) influence their growth. The EQCM-D results show consistently that much thicker SEIs are formed on carbon substrates in comparison to copper substrates. Full article

The cointercalation of solvated Mg²⁺ ions into graphite has typically been considered challenging because of concerns regarding the instability of the electrolyte and the potential for structural degradation. However, recent developments in electrolyte design suggest that this process may be reversible under appropriate conditions. In this study, the interfacial behavior of graphite in a magnesium-ion system was investigated using in situ electrochemical atomic force microscopy. Electrochemical tests in a triglyme-based electrolyte revealed a reversible capacity of 158 mAh g⁻¹, attributed to the insertion of triglyme-solvated Mg²⁺ ions. Real-time surface imaging of highly oriented pyrolytic graphite revealed the formation of a passivating surface film during the initial cycle, along with nanoscale hill-like (~1 nm) and blister-like (~5 nm) structures, which were partially reversible and showed good correlation with the redox peaks observed in the cyclic voltammetry experiments, suggesting that the surface film enables Mg²⁺ transport while mitigating electrolyte decomposition. These findings demonstrate that stable co-intercalation of solvated Mg²⁺ ions is achievable in the early cycles in graphite and highlight the importance of interfacial engineering and solvation structures in the development of magnesium-ion batteries. Full article