Search Results (737)

The electrochemical performance of Li-ion batteries employing LiFePO₄ (LFP) cathodes supported by bio-sourced activated carbon derived from millet cob (MC) and water hyacinth (WH) were systematically investigated. Carbon activation was carried out using potassium hydroxide (KOH) at varying mass ratios of KOH to precursor material: 1:1, 2:1, and 5:1 for both WH and MC-derived carbon. The physical properties (X-ray diffraction patterns, BET surface area, micropore and mesopore volume, conductivity, etc.) and electrochemical performance (specific capacity, discharge at various current rates, electrochemical impedance measurement, etc.) were determined. Material characterization revealed that the activated carbon derived from MC exhibits an amorphous structure, whereas that obtained from WH is predominantly crystalline. High specific surface areas were achieved with activated carbons synthesized using a low KOH-to-carbon mass ratio (1:1), reaching 413.03 m²·g⁻¹ for WH and 216.34 m²·g⁻¹ for MC. However, larger average pore diameters were observed at higher activation ratios (5:1), measuring 8.38 nm for KOH/WH and 5.28 nm for KOH/MC. For both biomass-derived carbons, optimal electrical conductivity was obtained at a 2:1 activation ratio, with values of 14.7 × 10⁻³ S·cm⁻¹ for KOH/WH and 8.42 × 10⁻³ S·cm⁻¹ for KOH/MC. The electrochemical performance of coin cells based on cathodes composed of 85% LiFePO₄, 8% of these activated carbons, and 7% polyvinylidene fluoride (PVDF) as a binder, with lithium metal as the anode were studied. The LiFePO₄/C (LFP/C) cathodes exhibited specific capacities of up to 160 mAh·g⁻¹ at a current rate of C/12 and 110 mAh·g⁻¹ at 5C. Both LFP/MC and LFP/WH cathodes exhibit optimal energy density at specific values of pore size, pore volume, charge transfer resistance (R_ct), and diffusion coefficient (D_Li), reflecting a favorable balance between ionic transport, accessible surface area, and charge conduction. Maximum energy densities relative to active mass were recorded at 544 mWh·g⁻¹ for LFP/MC 2:1, 554 mWh·g⁻¹ for LFP/WH 2:1, and 568 mWh·g⁻¹ for the reference LFP/graphite system. These performance results demonstrate that the development of high-performing bio-sourced activated carbon depends on the optimization of various parameters, including chemical composition, specific surface area, pore volume and size distribution, as well as electrical conductivity. Full article

Shale reservoirs offer significant potential for CO₂ geological sequestration due to their extensive nanopore networks and heterogeneous pore systems. This study comparatively assessed the CO₂ storage potential of the Lower Silurian Longmaxi and Lower Cambrian Qiongzhusi shales through an integrated approach involving organic geochemical analysis, mineralogical characterization through X-ray diffraction (XRD), mercury intrusion capillary pressure (MICP), low-pressure nitrogen and carbon dioxide physisorption, field-emission scanning electron microscopy (FE-SEM), stochastic 3D microstructure reconstruction, multifractal analysis, and three-dimensional succolarity computation. The results demonstrate that mineral assemblages and diagenetic history govern pore preservation: Longmaxi shales, with moderate maturity and shallower burial, retain abundant organic-hosted mesopores, whereas overmature and deeply buried Qiongzhusi shales are strongly compacted and mineralized, reducing pore availability. Multifractal spectra and 3D reconstructions reveal that Longmaxi develops broader singularity spectra and higher succolarity values, reflecting more isotropic meso-/macropore connectivity at the SEM scale, while Qiongzhusi exhibits narrower spectra and lower succolarity, indicating micropore-dominated and anisotropic networks. Longmaxi has nanometer-scale throats (D₅₀ ≈ 10–25 nm) with high CO₂ breakthrough pressures (P₁₀ ≈ 0.57 MPa) and ultra-low RGPZ permeability (mean ≈ 1.5 × 10⁻² nD); Qiongzhusi has micrometer-scale throats (D₅₀ ≈ 1–3 μm), very low breakthrough pressures (P₁₀ ≈ 0.018 MPa), and much higher permeability (mean ≈ 4.63 × 10³ nD). Storage partitioning further differs: Longmaxi’s median total capacity is ≈15.6 kg m⁻³ with adsorption ≈ 93%, whereas Qiongzhusi’s median is ≈12.8 kg m⁻³ with adsorption ≈ 70%. We infer Longmaxi favors secure adsorption-dominated retention but suffers from injectivity limits; Qiongzhusi favors injectivity but requires reliable seals. Full article

With the frequent occurrence of global droughts, modified biochar has demonstrated the potential to be an efficient soil amendment, which could affect carbon and nitrogen sequestration in arid soil. Therefore, this study investigated the co-application of pristine biochar (BC), Fe-modified biochar (FB) and H₂O₂-modified biochar (HB) with green manure during a 70-day laboratory incubation under drought conditions and normal moisture conditions. The emissions were quantified using gas chromatography, while microbial necromass carbon and nitrogen were measured by quantifying the amino sugar content by gas chromatography–mass spectrometry, and other soil carbon and nitrogen fractions were determined through chemical analysis. The results revealed that under drought conditions, compared to BC co-application with green manure, the total carbon loss of FB and HB co-application with green manure was reduced from 24.38% to 13.14% and 14.27%, respectively, and the total nitrogen loss was also reduced from 14.61% to 7.23% and 7.27%, respectively. This reduction occurred because FB and HB protected soil organic matter through iron oxide binding and micropore adsorption, thereby increasing the content of soil total humus acid (>5%) and microbial necromass nitrogen (>16%). In addition, under normal moisture conditions, BC, FB and HB co-application with green manure enhanced microbial activity and promoted the formation of stable total humus acid, thereby enhancing carbon and nitrogen sequestration. In conclusion, this study provides crucial theoretical support for the optimization of the green manure return via modified biochar co-application in arid environments. Full article

Environmental contamination is a critical global concern, primarily due to detrimental greenhouse gas (GHG) emissions, especially carbon dioxide (CO₂), which significantly contribute to climate change. Moreover, the presence of harmful heavy metals like Ni, Cd, Cu, Hg, and Pb in soil and water ecosystems has led to poor water quality. Noble metal nanoparticles (MNPs), for instance, Pd, Ag, Pt, and Au, have emerged as promising solutions for addressing environmental pollution. However, the practical utilization of MNPs faces challenges as they tend to aggregate and lose stability. To overcome this issue, the reverse double-solvent method (RDSM) was utilized to synthesis melamine-based porous polyaminals (POPs) as a supportive material for the in situ growing of silver nanoparticles (Ag NPs). The porous structure of melamine-based porous polyaminals, featuring aminal-linked (-HN-C-NH-) and triazine groups, provides excellent binding sites for capturing Ag⁺ ions, thereby improving the dispersion and stability of the nanoparticles. The resulting material exhibited ultrafine particle sizes for Ag NPs, and the incorporation of Ag NPs within the porous polyaminals demonstrated a high surface area (~279 m²/g) and total pore volume (1.21 cm³/g), encompassing micropores and mesopores. Additionally, the Ag NPs@POPs showcased significant capacity for CO₂ capture (2.99 mmol/g at 273 K and 1 bar) and effectively removed Cu (II), with a remarkable removal efficiency of 99.04%. The nitrogen-rich porous polyaminals offer promising prospects for immobilizing and encapsulating Ag nanoparticles, making them outstanding adsorbents for selectively capturing carbon dioxide and removing metal ions. Pursuing this approach holds immense potential for various environmental applications. Full article

Reservoirs and caprocks overlap with each other in heterogeneous carbonate rocks. The sealing capacity of caprocks and their controlling factors are not clear, which restricts the prediction, exploration, and development of carbonate hydrocarbon reservoirs. We selected core samples from the Ordovician reservoirs and caprocks in the Tarim Basin, China, for scanning electron microscopy, thin section, breakthrough pressure (BP), high-pressure mercury intrusion porosimetry (HMIP), and nitrogen adsorption method (N₂GA). The experimental results show that the reservoir and caprock can be distinguished by BP. The BP of the reservoir is less than 3.0 MPa, and the BP of the caprock is less than 3.0 Mpa. We analyzed the heterogeneity characteristics and differences in reservoirs and caprocks with different lithologies from the perspectives of monofractal and multifractal. The results indicate that the differences in pore structure of grainstone, dolomite, and micrite/argillaceous limestone result in significant heterogeneity differences between samples. The correlation analysis between the fractal parameters and BP indicates that the characteristics of reservoir microporous structures have a decisive impact on BP (correlation coefficient > 0.7). The pore structure of the carbonate reservoir–caprock system exhibits self-similarity. The heterogeneity of the caprock has no significant control effect on BP (correlation coefficient < 0.3), while the higher the heterogeneity of the reservoir, the greater the BP. The sealing capacity of the caprock depends on the heterogeneity differences in pore types and pore structures between the reservoirs and caprocks. When both the reservoir and the caprock are grainstone, the micropores in the reservoirs and caprocks are dispersed but evenly distributed, and little heterogeneous differences can achieve sealing. When the lithology of reservoirs and caprocks is different, the enhancement of heterogeneity differences in micropores will improve the sealing capacity of the caprock. In summary, fractal dimension is an effective method for studying the heterogeneous structure and sealing capacity of pore–throat in carbonate caprocks. This study proposes a new perspective that the difference between the heterogeneity of micropore structures of reservoirs and caprocks affects the sealing capacity of carbonate rocks, and provides a new explanation and model for the sealing mode of carbonate rock caprocks. Full article

Heteroatom doping is an effective strategy for improving the sodium storage performance of hard carbon. However, the use of sulfur and fluorine codoped carbon materials as anodes for sodium-ion batteries has not been reported. Here, an S-infused/S, F-codoped PVDF-derived carbon SFC5 was prepared by one-step carbonization of PVDF and synchronously used as an anode for a sodium-ion battery. The prepared SFC5 containing 10.11 at% S and 9.54 at% F is a short-range ordered amorphous carbon with a microporous structure. Owing to the structural advantages of S, F codoping, and the high specific capacity of S, SFC5 exhibited an outstanding sodium storage performance of 365 mAh g⁻¹ after 200 cycles at 50 mA g⁻¹ and 212 mAh g⁻¹ after 500 cycles at 400 mA g⁻¹. Moreover, theoretical calculations based on density functional theory (DFT) verify that S and F codoping can considerably reduce the Na⁺ adsorption energy and increase the electronic conductivity of SFC5. The current study presents a viable and facile approach to prepare high-performance, low-cost anode materials for SIBs, supported by empirical evidence and theoretical computations. Full article

To evaluate lignite degradation efficiency and the enhancement of biogas production by different microbial treatments, lignite was pre-treated with Streptomyces viridosporus (actinomycete), Phanerochaete chrysosporium (fungus), and Pseudomonas sp. (bacterium), followed by biogasification experiments. Among the three, Phanerochaete chrysosporium exhibited the highest lignite degradation rate. All microbial treatments improved both cumulative biogas yield and methane conversion, with Phanerochaete chrysosporium again demonstrating the most significant enhancement. Ultimate analysis after degradation showed the following consistent trends across all treatments: increases in carbon, hydrogen, and nitrogen contents, and reductions in sulfur and oxygen contents. A linear correlation was observed between the H/C atomic ratio and total biogas yield. Functional group analysis revealed the greatest reductions in key functional groups with Phanerochaete chrysosporium, followed by moderate changes with Pseudomonas and Streptomyces viridosporus. Pore structure characterization indicated that all microorganisms influenced lignite porosity, particularly in mesopore and micropore regions. Increases in pore volume and connectivity were associated with improved biogas production efficiency. Full article

Shale pore architecture governs gas storage capacity, permeability, and production potential in reservoirs. Therefore, this study systematically investigates the pore structure features and influencing factors of the Niutitang Formation shale from the QX1 well in northern Guizhou using field emission scanning electron microscopy (FE-SEM), high-pressure mercury intrusion (HPMI), low-temperature nitrogen adsorption (LTNA), and nuclear magnetic resonance (NMR) experiments. The results show that ① The pore size of the QX1 well’s Niutitang Formation shale is primarily in the nanometer range, with pore types including intragranular pores, intergranular pores, organic matter pores, and microfractures, with the former two types constituting the primary pore network. ② Pore shapes are plate-shaped intersecting conical microfractures or plate-shaped intersecting ink bottles, ellipsoidal, and beaded pores. ③ The pore size distribution showed a multi-peak distribution, predominantly mesopores, followed by micropores, with the fewest macropores. ④ The fractal dimension D₁ > D₂ indicates that the shale pore system is characterized by a rough surface and some connectivity of the pore network. ⑤ Carbonate mineral abundances are the main controlling factors affecting the pore structure of shales in the study area, and total organic carbon (TOC) content also has some influence, while clay mineral content shows negligible statistical correlation. Full article

This study investigates the adsorption performance of activated carbon (AC) derived from food and agricultural waste, specifically coffee grounds, coffee skin, bamboo, and palm leaves, for the removal of two antibiotics: amoxicillin (AMX) and sulfamethoxazole (SMX). The ACs were synthesized via KOH and ZnCl₂ chemical activation and characterized through BET surface area analysis, thermal stability, electrical conductivity, SEM, EDS, and FTIR. Among all samples, bamboo-derived AC (B-AC) exhibited superior properties, such as the highest surface area (860 m²/g), thermal stability (855 °C), conductivity (0.063 S/cm), and adsorption capacities (292.6 mg/g for AMX and 195.7 mg/g for SMX). SEM and EDS analyses confirmed successful antibiotic adsorption with morphological and elemental changes, while FTIR spectra indicated interaction with surface functional groups. Adsorption data were best described by the Langmuir and Dubinin–Radushkevich isotherm models, suggesting a monolayer physical adsorption process dominated by micropore filling (E < 8 kJ/mol). In contrast, BET and Flory–Huggins models exhibited poor fit, confirming the absence of multilayer or partition-based adsorption mechanisms. Kinetic modeling showed that AMX followed a pseudo-second-order model, while SMX exhibited a more complex adsorption behavior. Thermodynamic studies confirmed that both processes were spontaneous, with AMX adsorption being endothermic and entropy-driven and SMX being exothermic but favorable. These findings demonstrate the high potential of B-AC as a low-cost, eco-friendly, and efficient adsorbent for pharmaceutical removal from water, supporting circular economy and sustainability goals. Full article

Blast-furnace staves serve as critical protective components in ironmaking, requiring synergistic optimization of slag-coating behavior and self-protection capability to extend furnace lifespan and reduce energy consumption. Traditional integer-order heat transfer models, constrained by assumptions of homogeneous materials and instantaneous heat conduction, fail to accurately capture the cross-scale thermal memory effects and non-local diffusion characteristics in multiphase heterogeneous blast-furnace systems, leading to substantial inaccuracies in predicting dynamic slag-layer evolution. This review synthesizes recent advancements across three interlinked dimensions: first, analyzing design principles of zonal staves and how refractory material properties influence slag-layer formation, proposing a “high thermal conductivity–low thermal expansion” material matching strategy to mitigate thermal stress cracks through optimized synergy; second, developing a mechanistic model by introducing the Caputo fractional derivative to construct a non-Fourier heat-transfer framework (i.e., a heat-transfer model that accounts for thermal memory effects and non-local diffusion, beyond the instantaneous heat conduction assumption of Fourier’s law), which effectively describes fractal heat flow in micro-porous structures and interfacial thermal relaxation, addressing limitations of conventional models; and finally, integrating industrial case studies to validate the improved prediction accuracy of the fractional-order model and exploring collaborative optimization of cooling intensity and slag-layer thickness, with prospects for multiscale interfacial regulation technologies in long-life, low-carbon stave designs. Full article

This paper discusses the integrated technology of CO₂ adsorption and catalysis, which combines adsorption and catalytic conversion, simplifies the traditional process, reduces energy consumption, and improves efficiency. The traditional carbon capture technology has the problems of high energy consumption, equipment corrosion, and absorbent loss, while the integrated technology realizes the adsorption, conversion, and catalyst regeneration of CO₂ in a single reaction system, avoiding complex desorption steps. Through micropore confinement and surface electron transfer mechanism, the technology improves the reactant concentration and mass transfer efficiency, reduces the activation energy, and realizes the low-temperature and high-efficiency conversion of CO₂. In terms of materials, MOF-based composites, alkali metal modified oxides, and carbon-based hybrid materials show excellent performance, helping to efficiently adsorb and transform CO₂. However, the design and engineering of reactors still face challenges, such as the development of new moving bed reactors. This technology provides a new idea for CO₂ capture and resource utilization and has important environmental significance and broad application prospects. Full article

Severe polysulfide shuttling and sluggish redox kinetics critically hinder lithium–sulfur (Li-S) battery commercialization. In this study, a multifunctional diatomite (DE)/TiO₂/MoS₂/N-doped carbon nanofiber (NCNF) composite separator was fabricated via hydrothermal synthesis, electrospinning, and carbonization. DE provides dual polysulfide suppression, encompassing microporous confinement and electrostatic repulsion. By integrating synergistic catalytic effects from TiO₂ and MoS₂ nanoparticles, which accelerate polysulfide conversion, and conductive NCNF networks, which facilitate rapid charge transfer, this hierarchical design achieves exceptional electrochemical performance: a 1245.6 mAh g⁻¹ initial capacity at 0.5 C and 65.94% retention after 200 cycles. This work presents a rational multi-component engineering strategy to suppress shuttle effects in high-energy-density Li-S batteries. Full article

The cement sheath is critical for ensuring the long-term safety and operational efficiency of oil and gas wells. However, complex geological conditions and operational stresses during production can induce cement sheath deterioration and cracking, leading to reduced zonal isolation, diminished hydrocarbon recovery, and elevated operational expenditures. This study investigates the development of a novel microbial self-healing well cement slurry system, employing fly ash as microbial carriers and sustained-release microcapsules encapsulating calcium sources and nutrients. Systematic evaluations were conducted, encompassing microbial viability, cement slurry rheology, fluid loss control, anti-channeling capability, and the mechanical strength, permeability, and microstructural characteristics of set cement stones. Results demonstrated that fly ash outperformed blast furnace slag and nano-silica as a carrier, exhibiting superior microbial loading capacity and viability. Optimal performance was observed with additions of 3% microorganisms and 3% microcapsules to the cement slurry. Microscopic analysis further revealed effective calcium carbonate precipitation within and around micro-pores, indicating a self-healing mechanism. These findings highlight the significant potential of the proposed system to enhance cement sheath integrity through localized self-healing, offering valuable insights for the development of advanced, durable well-cementing materials tailored for challenging downhole environments. Full article

This study explored the potential of reusing eggshell powders as a renewable activating agent for producing porous carbon materials from coffee husk. Carbonization and activation experiments were conducted by heating the samples at a rate of 10 °C/min up to 850 °C under a nitrogen atmosphere. A custom-designed double steel-mesh sample holder was used to hold approximately 2.0 g coffee husk on the top, with varying masses of eggshell at the bottom to achieve eggshells to coffee husk mass ratios of 2:1, 4:1, 6:1 and 8:1. The results demonstrated that CO₂ released from the thermal decomposition of the eggshell powder significantly enhanced pore development at 850 °C. Compared to the pore properties of carbon material produced without eggshell (e.g., BET surface area of 321 m²/g), the activated carbon samples exhibited substantially improved pore properties (e.g., BET surface area in the range of 592 to 715 m²/g). Furthermore, the pore characteristics improved consistently with increasing eggshell content. Observations by scanning electron microscopy (SEM), energy dispersive X-ray spectroscopy (EDS) and Fourier-transform infrared spectroscopy (FTIR) confirmed the structural and chemical transformations of the resulting carbon materials. Under optimal carbonization-activation conditions, the resulting carbon materials derived from coffee husk exhibited microporous structures and slit-shaped pores, as indicated by the Type I isotherms and H4 hysteresis loops. Full article

In comparison to shallow coal seams, deep coal seams exhibit characteristics of high temperature, pressure, and in-situ stress, leading to significant differences in reservoir properties that constrain the effective development of deep coalbed methane (CBM). This study takes the Carboniferous deep 8# coal seam in the Yulin area of Ordos basin as the research subject. Based on the test results from core drilling wells, a comprehensive analysis of the characteristics and variation patterns of coal reservoir properties and a comparative analysis of the exploration and development potential of deep CBM are conducted, aiming to provide guidance for the development of deep CBM in the Ordos basin. The research results indicate that the coal seams are primarily composed of primary structure coal, with semi-bright to bright being the dominant macroscopic coal types. The maximum vitrinite reflectance (R_o,max) ranges between 1.99% and 2.24%, the organic is type III, and the high Vitrinite content provides a substantial material basis for the generation of CBM. Longitudinally, influenced by sedimentary environment and plant types, the lower part of the coal seam exhibits higher Vitrinite content and fixed carbon (FC_ad). The pore morphology is mainly characterized by wedge-shaped/parallel plate-shaped pores and open ventilation pores, with good connectivity, which is favorable for the storage and output of CBM. Micropores (<2 nm) have the highest volume proportion, showing an increasing trend with burial depth, and due to interlayer sliding and capillary condensation, the pore size (<2 nm) distribution follows an N shape. The full-scale pore heterogeneity (fractal dimension) gradually increases with increasing buried depth. Macroscopic fractures are mostly found in bright coal bands, while microscopic fractures are more developed in Vitrinite, showing a positive correlation between fracture density and Vitrinite content. The porosity and permeability conditions of reservoirs are comparable to the Daning–Jixian block, mostly constituting oversaturated gas reservoirs with a critical depth of 2400–2600 m and a high proportion of free gas, exhibiting promising development prospects, and the middle and upper coal seams are favorable intervals. In terms of resource conditions, preservation conditions, and reservoir alterability, the development potential of CBM from the Carboniferous deep 8# coal seam is comparable to the Linxing block but inferior to the Daning–Jixian block and Baijiahai uplift. Full article