Search Results (616)

Excessive copper ions in the human body can cause a variety of diseases, such as gastrointestinal disorders, cirrhosis, and Alzheimer’s disease. Techniques like Inductively Coupled Plasma–Mass Spectroscopy and Atomic Absorption Spectroscopy are available for copper detection, but the associated cost issues for sample preparation and labor limit their application for on-site detection. Herein, we are reporting a versatile method for detecting copper ions using a peptide-functionalized gold nanoparticle sensor in combination with various optical spectroscopic techniques. The peptide (CW) exhibited selective sensing ability for Cu(II) with visual colorimetric and optical spectroscopic changes compared to other metal ions tested. CW showed a visual colorimetric response from colorless to light brown color after interaction with Cu(II). Converting CW to a gold nanoparticle appended (CW-AuNPs) nanoplatform enabled a multimodal detection platform for Cu (II), which utilizes colorimetric and optical spectrum changes and surface-enhanced Raman spectroscopy (SERS) to enable highly sensitive sensing of Cu(II), even at extremely low concentrations (76 nms.). CW-AuNPs exhibit a controlled aggregation property in the presence of Cu(II), resulting in the creation of hot spots for SERS-based detection. Moreover, the peptide unit attached to the gold nanoparticles serves both as a binding motif for Cu(II) and as a Raman reporter for Cu(II) sensing. Our comprehensive analysis, including solution-state and dry-mapping Raman spectroscopic studies, demonstrates remarkable picomolar sensitivity of the peptide–gold nanoparticle system for Cu(II) detection. Moreover, we prepared a paper test strip from CW-AuNPs and used it as a visual colorimetric platform for sensitive detection of copper ions. Full article

Non-thermal or cold plasma is an innovative agricultural technology used for the treatment of seeds, producing physicochemical and biochemical changes without thermal damage and stimulating germination and plant growth. The interaction of reactive species generated in cold plasma modifies the morphology of the seed surface, increasing porosity, producing microcracks, removing material or producing other physical changes, and chemically modifying it. The changes induced positively influence the rate, speed, and uniformity of germination, as it is believed that these changes take place as a result of activated metabolic pathways, regulated hormone balance, and stimulated production of enzymes involved in the mobilisation of nutrient reserves needed for seedling growth. Plasma sources, electrical parameters, feed gas, and processing time are some of the essential factors involved in tuning the effects on seeds. Optimising the outcomes and their adaptation for specific species is crucial to maximise the benefits and avoid inhibitory effects. In the frame of ecological and sustainable agriculture, with the benefits given by cold plasma, this review follows the modifications produced by different sources on the seeds, starting from morphological changes to biochemical ones, up to germination, aiming to facilitate the understanding of the interaction and outcomes. We also address the challenges, including variability of biological responses, the need for standard procedures and parameters, and development of scalable technologies. A thorough examination of the changes induced in seeds as a result of non-thermal plasma treatment not only facilitates the improvement of experimental designs and reproducibility but also plays an important role in advancing seed treatment technologies and, ultimately, enhancing crop yields in a sustainable manner. Full article

This study investigates the elemental composition of magnetic nanoparticles (MNPs) in eleven wildland–urban interface (WUI) fire ashes, including one vegetation, six structural, and four vehicle ashes, along with three fire-impacted soil samples. The WUI fire ash samples were collected following the 2020 North Complex (NC) Fire and Sonoma–Lake–Napa unit (LNU) Lightning Complex Fire in California. Efficiency of magnetic separation was confirmed via Time-Domain Nuclear Magnetic Resonance (TD-NMR); the relaxometry showed that the transverse relaxation rate R₂ decreased from 2.02 s⁻¹ before separation to 0.29 s⁻¹ after separation (ΔR₂ = −1.73 s⁻¹; −86%), due to the removal of magnetic particles. The particle number concentrations, size distributions, and elemental compositions (and ratios) of MNPs were determined using single particle-inductively coupled plasma–time-of-flight-mass spectrometry (SP-ICP-TOF-MS). The major types of nanoparticles (NPs) detected in the magnetically separated MNPs were Fe-, Ti-, Cr-, Pb-, Mn-, and Zn-bearing NPs. The iron-bearing NPs accounted for 3.2 to 83.5% of the magnetically separated MNPs, and decreased following the order vegetation ash (77.4%) > soil (63.2–69.9%) > structural (3.2–83.5%) ash. The titanium-bearing NPs accounted for 3.3 to 66.1% of the magnetically separated MNPs, and decreased following the order vehicle (14.1–66.1%) > structural (3.5–36.4%) > vegetation (3.3%) ash. The majority of the detected NPs in the fire ashes occurred in the form of multi-metal (mm) NPs, attributed to the presence of NPs as heteroaggregates and/or due to the sorption of metals on the surfaces of NPs during combustion. However, a notable fraction (3–91%) of the detected NPs occurred as single-metal (sm) NPs, particularly smFe-bearing NPs, which accounted for 48 to 91% of all the Fe-bearing particles in the magnetically separated MNPs. The elemental ratios (e.g., Al/Fe, Ti/Fe, Cr/Fe, and Zn/Fe) in the magnetically separated MNPs from structural and vehicle ashes were higher than those in the soil samples and vegetation ashes, indicating enrichment of metals in magnetically separated NPs from vehicle and structural ashes compared to vegetation ash. Overall, this study demonstrates that the MNPs generated by WUI fire ash are associated with potentially toxic elements (e.g., Cr and Zn), exacerbating the environmental and human health risks of WUI fires. This study also highlights the need for further research into the properties, environmental fate, transport, and interactions of MNPs with biological systems during and following WUI fires. Full article

The proteolytic fraction (P1G10) from Vasconcellea pubescens displays pharmacological activity in diverse therapeutic settings. It is responsible for antifungal activity against Botrytis cinerea, impairing its germination and the integrity of the plasma membrane. The application of P1G10 is limited by stability in aqueous environments, where proteases lose activity. In this study, we aim to stabilize the proteolytic fraction, by complexation, to preserve the enzymatic activity ensued by controlled release. The proportion of each polymer, and the established reaction sequence, is chitosan (CS) plus P1G10 and alginate (ALG) using ALG:CS mass ratio = 1.0. Scanning electron microscopy (SEM) of the product shows the ALG-CS-P1G10 complex displaying a rough surface contrasting with the smoother surface of the ALG-CS complex, likely induced by interactions between the protein and ALG-CS complex. The optimal amount of protein taken up by the complex under this condition was 13 mg, and the incorporation yield was 72%. The melting temperature (Tm) determined by differential scanning calorimetry (DSC) in ALG-CS increased from 80 °C to 86 °C for the biocatalyst ALG-CS-P1G10; this difference was probably induced by the interactions between P1G10 and ALG-CS. Fourier transform infrared spectrometry (FTIR) comparison between ALG-CS and ALG-CS-P1G10 shows two bands in the biocatalyst at 1601 and 1523 cm⁻¹, suggesting the presence of amine residues from P1G10 which is rich in lysine residues. The release of P1G10 from the complex was assessed by increasing the ionic strength in the media between 0.1 and 0.4 M NaCl. The results show that, at 0.3 M NaCl, the protein released after 8 h attained 70% and expressed enzymatic activity of 0.90 × 10⁻³ U/mg protein compared to the enzymatic activity from free P1G10 protein, which was 5.55 × 10⁻⁴ U/mg protein. Full article

Graphene was directly grown on SiO₂/Si substrates using microwave plasma-enhanced chemical vapor deposition (PECVD) to investigate how synthesis-driven variations in structure and doping influence carrier transport. The effects of synthesis temperature, plasma power, deposition time, gas flow, and pressure on graphene’s structure and electronic properties were systematically studied. Raman spectroscopy revealed non-monotonic changes in layer number, defect density, and doping levels, reflecting the complex interplay between growth, etching, and self-doping mechanisms. The surface morphology and conductivity were assessed by atomic force microscopy (AFM). Charge carrier mobility, extracted from graphene-based field-effect transistors, showed strong correlations with Raman features, including the intensity ratios and positions of the Two-dimension (2D) and G peaks. Importantly, mobility did not correlate with defect density but was linked to reduced self-doping and a weaker graphene–substrate interaction rather than intrinsic structural disorder. These findings suggest that charge transport in PECVD-grown graphene is predominantly limited by interfacial and doping effects. This study offers valuable insights into the synthesis–structure–property relationship, which is crucial for optimizing graphene for electronic and sensing applications. Full article

This research presents an experimental analysis of the influence of atmospheric pressure plasma on the performance of a micro horizontal-axis wind turbine blade. The investigation was conducted using an NACA 4412 airfoil equipped with a dielectric barrier discharge (DBD) plasma actuator. The electrodes were configured asymmetrically, with a 2 mm gap and copper electrodes that are 0.20 mm in thickness. A high voltage of 6 kV was applied, resulting in a current of 0.071 mA and a power output of 0.426 W. Optical emission spectroscopy identified the excited components through the interaction of the high-voltage AC electric field with air molecules: ${\mathrm{N}}_2$, ${\mathrm{N}}_2^{+}$, ${\mathrm{O}}_2^{+}$, and O. The electrohydrodynamic force mainly results from the observed charged ions that, when accelerated by the electric field, transfer momentum to neutral molecules via collisions, leading to the formation of the observed jet plasma. The findings indicated a notable enhancement in aerodynamic performance attributable to the electrohydrodynamic (EHD) flow generated by the plasma. The estimated electrohydrodynamic force ($8.712\times {10}^{-4}$ N) is capable of maintaining the flow attached to the airfoil surface, thereby augmenting flow circulation and, consequently, enhancing the lift force. According to blade element theory, the lift and drag coefficients directly influence the torque and mechanical power generated by the wind turbine rotor. Schlieren imaging was utilized to observe alterations in air density and flow patterns. Lissajous curve analysis was used to examine the electrical discharge behavior, showing that only 7.04% of the input power was converted into heat. This indicates that nearly all input electric energy was transformed into EHD force by the atmospheric pressure plasma. Compared to traditional aerodynamic control methods, DBD actuators are a feasible alternative for small wind turbines due to their lightweight design, absence of moving parts, ability to be surface-embedded without altering blade geometry, and capacity to generate active, dynamic flow control with reduced energy consumption. Full article

During the laser cladding process, the temperature, flow velocity, and element concentration of the molten pool will be affected by the plasma. Quantitative analysis of the mechanism by which the plasma affects heat and mass transfer during the laser cladding process is of great significance for improving the quality of the cladding layer. In this paper, a multi-field coupled numerical model of the laser cladding process of Fe60 using an ASTM 1045 disk laser was established. In the modeling, the interaction between the plasma cloud and the laser beam (the ionization process of metal vapor absorbing photon energy and the absorption and shielding effect of the plasma on laser energy), as well as the influence of surface tension, buoyancy, and shock waves generated by the expansion of the plasma cloud on the Marangoni flow of the liquid metal, was considered. A comparative analysis was performed on the transient evolution of the temperature field, flow field, and concentration field during the laser cladding process in the presence of the plasma cloud. The results show that the ionization process of metal vapor and the shielding effect of the plasma cloud cause a decrease in laser energy and the temperature of the cladding layer. The Marangoni flow is affected by the shock waves generated by the expansion of the plasma cloud, resulting in a decrease in the flow velocity of the melt. A slight decrease in the concentration of Fe, Cr, and Ni elements and a slight increase in the concentration of C element in the cladding layer are caused by melt evaporation. Full article

This study investigates a novel approach based on micro-pulse plasma electrolytic oxidation (μPPEO), aiming to improve the control over key parameters such as the Ca/P ratio, the formation of anatase and rutile phases, and the porosity of titanium surfaces—factors that are critical for enhancing bioactivity. By employing electrical micro-pulses with widths of 50 μs or 100 μs, our aim was to restrict the discharge time and subsequent surface/electrolyte reactions. The results demonstrate that μPPEO-treated surfaces exhibit uniform pore diameters, a Ca/P ratio of approximately 1.67, and the better control of anatase/rutile formation. The μPPEO treatment successfully produced hydrophilic surfaces, with the 6Ti50 sample displaying the highest polar component of surface energy. Notably, this sample was the only one to support cell viability comparable to that of the polystyrene surface on the 24-well plate, emphasizing its strong potential for clinical applications. Across all treated surfaces, OFCOL osteoblasts displayed a spindle-like morphology with elongated filopodia, suggesting favorable cell interactions and adaptability to the treated surfaces. This study underscores the promise of PPEO as a valuable technique for biomedical applications, particularly in controlling and optimizing dental implant surfaces. Full article

Recent updates to European Union directives on drinking water have extended safety limits to hot water, increasing the need to assess materials commonly used in water storage systems, such as porcelain enamel. This study investigates the interaction between enameled surfaces and aqueous environments, focusing on element release and microstructural alterations. The mass loss and chemical stability of the enamel were evaluated through a combination of surface characterization and Inductively Coupled Plasma (ICP) analysis. Time-resolved quantification of selected elements confirmed that all concentrations remained within EU regulatory thresholds. Additionally, the enamel was subjected to acidic and alkaline environments to explore the influence of pH on degradation mechanisms. Scanning electron microscopy (SEM) revealed that while the enamel undergoes surface-level modifications, the bulk structure remains intact. Notably, alkaline exposure had the strongest impact, dissolving needle-like calcium-rich structures and altering the surface more significantly than water or acid alone. These structures appear to facilitate localized corrosion once degraded. The correlation between surface morphology and elemental release dynamics highlights the critical role of microstructural features in determining long-term chemical resistance. Overall, the results underscore the importance of optimizing both the composition and structure of enamel coatings for applications involving prolonged contact with potable water. Full article

Background Plasma membrane proteins (PMPs) play key roles in cell signalling, adhesion, and trafficking, and are attractive therapeutic targets in cancer due to their surface accessibility. However, their typically low abundance limits detection by conventional proteomic approaches. Methods: To improve PMP detection, we employed a surface proteomics workflow combining cell surface biotinylation and affinity purification prior to LC-MS/MS analysis in cervical (SiHa) and bladder (UMUC3) cancer cell lines cultured under normoxic (21% O₂) or hypoxic (0.1% O₂) conditions. Results: In SiHa cells, 43 hypoxia-upregulated proteins were identified exclusively in the biotin-enriched fraction, including ITGB2, ITGA7, AXL, MET, JAG2, and CAV1/CAV2. In UMUC3 cells, 32 unique upregulated PMPs were detected, including CD55, ADGRB1, SLC9A1, NECTIN3, and ACTG1. These proteins were not observed in corresponding whole-cell lysates and are associated with extracellular matrix remodelling, immune modulation, and ion transport. Biotinylation enhanced the detection of membrane-associated pathways such as ECM organisation, integrin signalling, and PI3K–Akt activation. Protein–protein interaction analysis revealed links between membrane receptors and intracellular stress regulators, including mitochondrial proteins. Conclusions: These findings demonstrate that surface biotinylation improves the sensitivity and selectivity of plasma membrane proteomics under hypoxia, revealing hypoxia-responsive proteins and pathways not captured by standard whole-cell analysis. Full article

The paper shows the effect of using a lubricant in the form of an ionic liquid, 1-butyl-3-methylimidazolium hexafluorophosphate (BMIM-PF₆), on the tribological properties of a hydrogenated diamond-like coating (DLC) doped with tungsten a-C:H:W. The coatings were deposited on 100Cr6 steel by plasma-enhanced chemical vapor deposition PECVD. Tribological tests were carried out on a TRB³ tribometer in a rotary motion in a ball–disc combination. 100Cr6 steel balls were used as a counter-sample. Friction and wear tests were carried out for discs made of 100Cr6 steel and 100Cr6 steel discs with a DLC coating. They were performed under friction conditions with and without lubrication under 10 N and 15 N loads. The ionic liquid BMIM-PF₆ was used as a lubricant. Coating thickness was observed on a scanning microscope, and the linear analysis of chemical composition on the cross-section was analyzed using the EDS analyzer. The confocal microscope with an interferometric mode was used for analysis of the geometric structure of the surface before and after the tribological tests. The contact angle of the samples for distilled water, diiodomethane and ionic liquid was tested on an optical tensiometer. The test results showed good cooperation of the DLC coating with the lubricant. It lowered the coefficient of friction in comparison to steel about 20%. This indicates the synergistic nature of the interaction: DLC coating–BMIM-PF₆ lubricant–100Cr6 steel. Full article

In this study, a simple, mild, and eco-friendly cold plasma-solution interaction method is employed to rapidly prepare gold colloids. Through modification with multi-walled carbon nanotubes (MWCNTs), a non-enzymatic glucose-sensing electrode material is successfully fabricated. The prepared electrode material is characterized via X-ray diffraction (XRD), Fourier transform infrared spectroscopy (FTIR), X-ray photoelectron spectroscopy (XPS), and transmission electron microscopy (TEM). The results show that compared with the chemically reduced AuNPs-C-MWCNTs, the plasma-prepared AuNPs-P-MWCNTs exhibits enhanced glucose catalytic performance with a higher sensitivity of 73 μA·mM⁻¹·cm⁻² (approximately 3.2 times that of AuNPs-C-MWCNTs), lower response time of 2.1 s, and ultra-low detection limit of 0.21 μM. It also demonstrates excellent selectivity, reproducibility (RSD = 4.37%), repeatability (RSD = 3.67%), and operational stability (RSD = 4.51%). This improvement can be attributed to the smaller particle size and better dispersion of plasma-derived AuNPs on the surface of MWCNTs. Furthermore, the AuNPs-P-MWCNTs surface is enriched with oxygen-containing functional groups, which is conducive to the enhancement of the hydrophilicity of the electrode surface. These synergistic effects facilitate the AuNPs-catalyzed glucose oxidation reaction, ultimately leading to superior glucose catalytic performance. Full article

When a semiconducting sample is illuminated by an intensity-modulated monochromatic light beam with photon energy exceeding the band gap, part of the absorbed energy is directly converted into heat through photon–lattice interactions. This gives rise to a heat source that closely follows the temporal profile of the optical excitation, known as the fast heat source. Simultaneously, another portion of the absorbed energy is used to generate electron-hole pairs. These charge carriers diffuse together and recombine via electron–electron and electron–hole interactions, transferring their kinetic energy to the lattice and producing additional heating of the sample. This indirect heating mechanism, associated with carrier recombination, is referred to as the slow heat source. In this study, we develop a model describing surface temperature variations on the non-illuminated side of a thermally thin semiconductor exposed to a rectangular optical pulse, explicitly accounting for the contribution of surface charge carrier recombinations. Using this model, we investigate the influence of surface recombination velocity and the material’s plasma properties on the time-domain temperature response for both plasma-opaque and plasma-transparent samples. Our results demonstrate that charge carrier recombinations can significantly affect the transient photoacoustic signal recorded using a minimum volume cell, highlighting the potential of time-resolved photoacoustic techniques for probing the electronic properties of semiconductors. Full article

Trichomonas vaginalis, a prevalent sexually transmitted protozoan parasite, is associated with adverse birth outcomes, increased risk of HIV and other sexually transmitted infections, infertility, and cervical cancer. Despite its widespread impact, trichomoniasis remains underdiagnosed and underreported globally. Trichomonas vaginalis virus (TVV), a double-stranded RNA (dsRNA) virus infecting T. vaginalis, could impact T. vaginalis pathogenicity. We provide an overview of TVV, including its genomic structure, transmission, impact on protein expression, role in 5-nitroimidazole drug susceptibility, and clinical significance. TVV is a ~5 kbp dsRNA virus enclosed within a viral capsid closely associated with the Golgi complex and plasma membrane of infected parasites. Hypothetical mechanisms of TVV transmission have been proposed. TVV affects protein expression in T. vaginalis, including cysteine proteases and surface antigens, thus impacting its virulence and ability to evade the immune system. Additionally, TVV may influence the sensitivity of T. vaginalis to treatment; clinical isolates of T. vaginalis not harboring TVV are more likely to be resistant to metronidazole. Clinically, TVV-positive T. vaginalis infections have been associated with a range in severity of genital signs and symptoms. Further research into interactions between T. vaginalis and TVV is essential in improving diagnosis, treatment, and the development of targeted interventions. Full article

Erosion detection in materials exposed to plasma-generated species, such as those used for space propulsion systems, is critical for ensuring their reliability and longevity. This study introduces an efficient image processing technique to monitor the evolution of the erosion depth in boron nitride (BN) subjected to multiple cycles of iodine plasma exposure. Utilising atomic force microscopy (AFM) images from both untreated and treated BN samples, the technique uses a modified semi-automated image registration method that accurately aligns surface profiles—even after substantial erosion—and overcomes challenges related to changes in the eroded surface features. The registered images are then processed through frequency-domain subtraction to visualise and quantify erosion depth. Our technique tracks changes across the BN surface at multiple spatial locations and generates erosion maps at exposure durations of 24, 48, 72 and 84 min using both one-stage and multi-stage registration methods. These maps not only reveal localised material loss (up to 5.5 μm after 84 min) and assess its uniformity but also indicate potential re-deposition of etched material and redistribution across the surface through mechanisms such as diffusion. By analysing areas with higher elevations and observing plasma-treated samples over time, we notice that these elevated regions—initially the most affected—gradually decrease in size and height, while overall erosion depth increases. Progressive surface smoothing is observed with increasing iodine plasma exposure, as quantified by AFM-based erosion mapping. Notably, up to 89.3% of surface heights were concentrated near the mean after 72–84 min of plasma treatment, indicating a more even distribution of surface features compared to the untreated surface. Iodine plasma was compared to argon plasma to distinguish material loss during degradation between these two mechanisms. Iodine plasma causes more aggressive and spatially selective erosion, strongly influenced by initial surface morphology, whereas argon plasma results in milder and more uniform surface changes. Additional scale-dependent slope and curvature analyses confirm that iodine rapidly smooths fine features, whereas argon better preserves surface sharpness over time. Tracking such sharpness is critical for maintaining the fine structures essential to the fabrication of modern semiconductor components. Overall, this image processing tool offers a powerful and adaptable method for accurately assessing surface degradation and morphological changes in materials used in plasma-facing and space propulsion environments. Full article