Search Results (1,204)

The rational design of electrode materials with tailored composition and architecture is crucial for advancing high-capability electrochemical energy storage systems. This study reports that gadolinium-modified NiFe₂O₄ nanosheet electrodes were effectively synthesized on nickel foam via a hydrothermal approach followed by thermal treatment. A series of compositions (NiFe, NiFe–Gd1, NiFe–Gd2, and NiFe–Gd3) were prepared to systematically examine the effect of Gd incorporation on structural features and electrochemical properties. X-ray diffraction (XRD) analysis confirmed the formation of the cubic spinel NiFe₂O₄ phase without detectable secondary phases, indicating that the crystal structure remains intact after Gd introduction. X-ray photoelectron spectroscopy (XPS) further verified the presence of Ni²⁺, Fe³⁺, and Gd³⁺ species within the lattice environment. Morphological analysis using field-emission scanning electron microscopy (FESEM) revealed a nanosheet-based architecture, where the optimized NiFe–Gd2 electrode exhibited a porous and interconnected nanosheet framework with abundant exposed edges. This structural configuration improves electrolyte penetration and facilitates efficient ion transport during charge storage processes. Electrochemical measurements demonstrated that the NiFe–Gd2 electrode delivers an areal capacitance of 5235 mF cm⁻² at 10 mA cm⁻², along with improved reaction kinetics and low internal resistance. An asymmetric supercapacitor assembled using NiFe–Gd2 as the positive electrode and activated carbon as the negative electrode operated stably within a 0–1.5 V potential window, achieving an energy density of 0.136 mWh cm⁻² and a power density of 3.14 mW cm⁻², while retaining 86.55% of its initial capacitance after 7000 cycles. These results highlight the potential of rare-earth engineering as a viable strategy for designing advanced spinel ferrite electrodes and pave the way for the development of high-performance, durable, and scalable supercapacitor systems for practical energy storage applications. Full article

Non-invasive magnetic resonance imaging (MRI), as an extension of nuclear magnetic resonance (NMR) technology, enables detailed characterization of lithium-ion batteries (LIBs) in model systems. This review summarizes the fundamental principles of MRI and its applications in liquid/solid electrolytes, electrodes, and limited commercial diagnostics. Key capabilities include quantifying ion diffusion coefficients and mobility numbers in electrolytes, visualizing dendrite growth in lithium metal, and tracking lithium distribution in porous electrodes such as graphite and LiCoO₂. However, spatial and temporal resolution (typically 10–100 μm with acquisition times ranging from minutes to hours) and metal-induced shielding effects severely limit direct imaging in complete commercial batteries. Indirect methods like magnetic field imaging (MFI) show potential for defect detection. Future work should focus on sequence optimization and multimodal fusion, while emphasizing MRI’s primary role in fundamental research rather than conventional industrial testing. Full article

The development of reliable electrochemical interfaces for biosensor applications requires materials that combine high conductivity, large effective surface area, and suitable platforms for biomolecule immobilization. In this work, a hybrid electrochemical platform based on screen-printed carbon electrodes (SPCEs) modified with electropolymerized polypyrrole (PPy) and electrodeposited silver particles (AgPs) is presented for the subsequent immobilization of Ki-67 antibodies. PPy films were synthesized under optimized electrochemical conditions, producing homogeneous, porous, and electrochemically stable coatings that significantly enhanced the doping/undoping processes from 0.3280 C/0.3284 C to 0.3281 C/0.3284 C for SPCE and SPCE-PPy, respectively. Subsequently, silver particles were deposited onto the PPy matrix, resulting in a well-dispersed and uniform distribution of AgPs, promoted by the interaction between Ag⁰ and the nitrogen groups in the polymer backbone. The synergistic combination of PPy and AgPs resulted in improved charge-transfer properties and enhanced electrochemical reversibility, thereby decreasing the peak-to-peak separation of the ferricyanide/ferrocyanide redox couple used as a probe by 40%. Immobilization of Ki-67 antibodies was achieved via direct interaction with AgPs, resulting in a marked passivation effect, as evidenced by the suppression of redox probe signals, confirming successful biofunctionalization. The proposed SPCE-PPy-AgP architecture provides a robust, reproducible, and versatile platform for antibody immobilization, as demonstrated by oxidation and reduction peaks with relative standard deviations (RSDs) of 3.18% and 4.43%, respectively, highlighting its potential for developing label-free electrochemical immunosensors for clinically relevant proliferation biomarkers. Full article

CdSe-coated electrodes, formed by electrodeposition of CdSe barrier layers on metallic Ti or porous TiO₂ substrates, were characterized by electrochemical impedance spectroscopy in a (photo)cell using aqueous redox electrolytes based on the sulfide/polysulfide or ferro/ferricyanide couples. The influence of electrode material properties, electrolyte contact, thermal annealing, and measurement conditions (illumination, frequency, potential-scan speed) on the shape and features of Mott–Schottky plots was investigated. The obtained information was evaluated on the basis of the ideal Schottky diode model and photocurrent voltammetry data. Deviations from linear diode behavior and uncertainties in the determination of energetic parameters were examined and attributed to the presence of donor density gradients and surface states in the semiconductor electrode, further complicated by chemical corrosion. The origin of the observed non-idealities is inquired into, and specific aspects of the measuring procedure related to the non-stationary character of the interface are discussed. Full article

Background: The growing demand for sustainable, high-performance energy storage systems has intensified interest in biomass-derived materials for supercapacitor applications. This study presents a green and scalable approach to fabricating novel electrodes and solid-state electrolytes using Phoenix dactylifera (Ajwa date) seed biomass and palm waste-derived activated carbon. Methods: KOH-activated carbon from date pits was employed to enhance surface area and redox activity. A double-network hydrogel electrolyte (DSHC) was synthesized by incorporating 0.5 g of date seed powder with sodium alginate and wheat starch (0.2 g each), followed by chemical crosslinking in 2 M H₂SO₄. Structural and physicochemical properties were analyzed using SEM, XRD, and FTIR, while electrochemical performance was evaluated through cyclic voltammetry and galvanostatic charge–discharge measurements. Results: SEM revealed a densely ordered porous network with regular cylindrical channels favorable for ion transport. XRD and FTIR confirmed amorphous carbon formation and effective molecular crosslinking. The hydrogel electrolyte exhibited a wide potential window of ~2 V and strong pseudocapacitive behavior, delivering a maximum specific capacitance of 179 F g⁻¹ at 5 mV s⁻¹ and a discharge capacitance of 159 F g⁻¹ at 0.2 A g⁻¹, with excellent stability over 5500 cycles. Conclusions: Agricultural waste-derived materials demonstrate strong potential as low-cost, eco-friendly, and mechanically robust components for flexible supercapacitors, suitable for sustainable energy storage and rapid-charging applications. Full article

Antibiotics are extensively used in intensive livestock farming for disease prevention, resulting in the discharge of antibiotic-contaminated wastewater into aquatic environments. Addressing this issue, electrocatalytic oxidation has emerged as a promising alternative to conventional chemical oxidation due to its cost-effectiveness and minimal secondary pollution. Central to this technology is the development of catalytic electrodes with high specific surface area and superior electrocatalytic activity. In this work, an Fe₃O₄-modified activated carbon fiber electrode (Fe₃O₄@ACF) was fabricated via a co-precipitation method. The Fe₃O₄@ACF electrode exhibited a hierarchical porous structure with a specific surface area of 940.2 m²/g, and demonstrated significantly enhanced oxygen reduction reaction activity with a current density of 21.8 mA·cm⁻² at –3.25 V vs. Ag/AgCl, which is 2.3 times higher than that of pristine ACF. EIS analysis revealed a low charge transfer resistance of 7.18 Ω, indicating improved electron transfer kinetics. In electro-Fenton degradation of tetracycline, the electrode achieved 82% removal within 120 min with a first-order rate constant of 0.01335 min⁻¹, and maintained over 94% of its initial activity after ten cycles. This study offers a viable and sustainable strategy for the efficient treatment of antibiotic-containing medical wastewater. Full article

Electrochromic devices have emerged as promising candidates for non-emissive displays due to their particular photoelectric performance in complex lighting environments. They exhibit considerable potential in emerging fields such as Internet of Things terminals, flexible wearables and human–computer interaction interfaces. In this study, we developed a low-power electrochromic display based on a Pt/FTO (Fluorine doped tin oxide) electrocatalytic counter electrode and a Poly(vinylidene fluoride-co-hexafluoropropylene) (PVDF-HFP) porous gel electrolyte. The Pt catalyst enhances Br⁻/Br³⁻ redox reactivity, which reduces the driving voltage from 2 V to 1 V, and accelerates the electrode reaction kinetics. It is systematically explained by the Density Functional Theory (DFT) calculations and electrochemical characterization. Furthermore, we demonstrate a proof-of-concept multicolor display incorporating the electrocatalytic counter electrode with various viologen derivatives. This approach provides a significant advancement toward next-generation high-performance displays and is supportive of the development of energy-efficient optoelectronic devices. Full article

This project investigates how the orientation of the carbon cathode with a single-sided microporous layer (MPL) affects battery performance through electrochemical tests, neutron tomography, and titration experiments. The titration experiment quantitatively assesses the amount of solid product (Li₂O₂) deposited on the electrode surface. In addition, neutron imaging with a 16 µm voxel resolution provides details on the spatial distribution of the solid product within the porous electrodes. Additionally, the performance impact of two electrolyte solvents, tetra ethylene glycol dimethyl ether (TEGDME) and dimethyl sulfoxide (DMSO), is evaluated when used to soak the carbon cathode. The cathode orientation where the MPL faces toward the electrolyte and separator reaches higher discharge and charge capacities and greater average discharge voltages compared to when the MPL faces away from the separator. Batteries discharged with DMSO as the solvent have a 64.86% decrease on average in discharge capacity compared to batteries using TEGDME as the solvent. Both the titration experiments and neutron imaging confirmed that the amount of solid products exhibits a linear correlation with the discharged capacity. Additionally, electrolytes with a high donor number, such as DMSO, were found to result in a smaller amount of Li₂O₂ deposited on the electrode surface. Full article

Bifunctional materials present a promising route to develop advanced devices, yet the dual performance of CoNi₂S₄ nanosheets anchored on a porous scaffold is seldom reported. Herein, we propose a rational fabrication strategy to construct a three-dimensional hierarchical electrode via the in-situ growth of densely aligned CoNi₂S₄ nanosheets on a conductive fabric scaffold. This integrated porous architecture concurrently offers an ultrahigh specific surface area, efficient mass transport, and rapid electron conduction. As a supercapacitor, the electrode achieves a high areal capacitance of 3198 mF cm⁻² at 4 mA cm⁻² and retains 98.1% of its initial capacitance after 1000 cycles at 20 mA cm⁻². As a non-enzymatic glucose sensor, it exhibits outstanding selectivity (<4.1% interference), high sensitivity (1049 μA mM⁻¹ cm⁻²), a wide linear range (1–8 mM), and a low detection limit (1 μM). These results highlight the significant potential of this binder-free, scaffold-supported nanosheet design for advancing integrated energy storage and biosensing systems. Full article

Benefiting from their outstanding porosity, considerable specific surface area, and natural flexibility, cellulose nanofibers (CNFs)/MOF materials have emerged as competitive candidates for advanced flexible energy storage devices. However, conventional CNFs/MOFs aerogels or films often suffer from poor recoverability under compression, bending, and folding, accompanied by severe plastic deformation that compromises the cycling and structural stability of devices. To address this issue, we report a rationally designed flexible PU/CNFs/ZIF-8/PANI composite foam with an interconnected micro-mesoporous structure. Using polyurethane foam as a soft substrate and CNFs/ZIF-8 as building blocks, the composite was fabricated through a combined strategy of impregnation, in situ ZIF-8 growth, hot-pressing, and in situ aniline polymerization with simultaneous etching of the ZIF-8. The incorporation of carboxylated CNFs enhances the hydrophilicity of the PU skeleton. This, in combination with the hot-pressed framework, establishes an interconnected 3D network, thereby effectively preventing the agglomeration of active materials. Meanwhile, the hierarchical pores derived from the sacrificial ZIF-8 template provide abundant electroactive sites, accelerate ion transport, and facilitate high PANI loading. By virtue of this synergistic architectural effect, the resultant electrode achieves a high specific capacitance of 449 F/g at 0.2 A/g, with 97% capacitance retention after 2000 cycles at 5 A/g. Furthermore, the composite foam demonstrates excellent mechanical flexibility, with a tensile strength of 0.87 MPa and an elongation at break of 230%. This work offers a feasible approach for developing high-performance flexible supercapacitors and provides novel perspectives for the rational design of portable energy storage devices. Full article

In this study, a novel layered WO₃@Co₃O₄ composite electrode was synthesized via a controlled electrodeposition method employing different surfactants to finely tune its nanostructure. The incorporation of polyacrylic acid (PAA) surfactant yielded an optimized P-W@Co electrode with a hierarchical porous morphology and reduced crystallite size, markedly enhancing electroactive site exposure and electron transport. Structural analyses confirmed the amorphous nature of WO₃ and crystalline spinel Co₃O₄ phases forming an integrated composite architecture. Electrochemical characterizations in a three-electrode system revealed that the P-W@Co electrode exhibited superior pseudocapacitive behavior, with an areal capacitance of 11.70 F/cm² at 20 mA/cm² and excellent rate capability, retaining 80% capacitance at 40 mA/cm². Kinetic studies demonstrated enhanced diffusion-controlled charge storage attributed to improved ion accessibility and charge transfer kinetics. To evaluate practical feasibility, asymmetric supercapacitor devices incorporating P-W@Co as the positive electrode coupled with activated carbon as the negative electrode were fabricated. This device showcased a widened operational voltage (1.5 V), outstanding areal capacitance (211 mF/cm²), and energy density (0.066 mWh/cm²). Importantly, the device exhibited exceptional cycling stability, retaining 81.8% capacitance after 7000 cycles. This work signifies a major advancement in surfactant-mediated design of WO₃@Co₃O₄ layered electrodes for scalable, high-performance supercapacitor applications, combining structural stability, enhanced conductivity, and multifaceted charge storage mechanisms. Full article

In this work, Fe, Co, Ni, Cu, and Mo powders were used as starting materials to prepare high-entropy alloy (HEA) thin films by a coating and vacuum sintering process. Using the HEA thin film as the substrate, selenium was subsequently deposited by chemical vapor deposition (CVD) to obtain high-entropy alloy selenide thin films (HEASe). The phase structure, surface chemical states, morphology, and elemental distribution of the porous films were characterized by X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), scanning electron microscopy (SEM), and energy-dispersive X-ray spectroscopy (EDS). The electrocatalytic hydrogen evolution performance of the electrodes was evaluated using a three-electrode configuration in 0.5 M H₂SO₄, 1 M KOH, 1 M KOH + 0.5 M NaCl, and 1 M KOH + 0.5 M Na₂S solutions. The results indicate that the HEA selenide thin-film electrodes exhibit favorable electrocatalytic behavior in all four electrolytes. Among them, HEASe-450 shows the best overall performance. In 0.5 M H₂SO₄, it requires an overpotential of only 57.6 mV to reach a current density of 10 mA cm⁻², with a Tafel slope of 146.96 mV dec⁻¹. In 1 M KOH, the overpotential at 10 mA cm⁻² is 50.1 mV, and the corresponding Tafel slope is 142 mV dec⁻¹. In 1 M KOH + 0.5 M NaCl, the overpotential is 52.7 mV with a Tafel slope of 122.72 mV dec⁻¹. In 1 M KOH + 0.5 M Na₂S, an overpotential of 85 mV is required, and the Tafel slope increases to 236 mV dec⁻¹. Full article

Developing sustainable electrode materials from renewable biomass is important for improving the environmental sustainability of lithium-ion batteries (LIBs). Sugarcane bagasse lignin, an abundant agricultural byproduct, is a promising precursor for lignin-derived carbon anode materials, yet systematic comparative studies on catalyst-dependent structure evolution and LIB performance remain limited. In this study, lignin extracted from sugarcane bagasse by an ethanosolv process was converted into Fe- and Ni-catalyzed lignin-derived carbon materials via catalytic pyrolysis at 900 °C. The effects of catalyst type, metal-to-lignin ratio, and pyrolysis holding time on textural properties, structural features, and electrochemical behavior were systematically investigated. Among the studied conditions, the Fe-catalyzed sample prepared at a metal-to-lignin ratio of 1:2.5 and a holding time of 3 h (GLKL-2.5Fe-3h) exhibited the highest BET surface area (332.71 m² g⁻¹) and the most developed porous morphology. SEM, TEM, Raman, and XRD analyses indicated catalyst-dependent differences in pore development, carbon domain morphology, and local graphitic ordering, with Fe- and Ni-catalyzed samples following distinct structural evolution pathways. Electrochemical testing showed that GLKL-2.5Fe-3h delivered the highest initial discharge capacity (759 mAh g⁻¹), retained 165 mAh g⁻¹ after 500 cycles, and exhibited more favorable rate performance and lower apparent interfacial resistance than the other tested samples under the same conditions. In contrast, the Ni-catalyzed and solvothermally treated samples showed lower capacity retention and/or less favorable electrochemical behavior. These results demonstrate the strong effect of catalyst type on the structure-performance relationship of bagasse lignin-derived carbon anodes and support Fe-catalyzed lignin-derived carbon as a promising sustainable anode candidate for LIB applications. Full article

Urea electrolysis has emerged as a promising alternative to conventional water electrolysis for hydrogen production, owing to low electrical energy consumption as well as organic wastewater. However, the practical implementation of this approach is primarily constrained by the lack of cost-effective and efficient electrocatalysts. Thus, the development of earth-abundant, non-precious metal-based bifunctional electrocatalysts toward both the hydrogen evolution reaction (HER) and the urea oxidation reaction (UOR) is of critical importance. In this context, nanostructured, reduced nickel-cobalt tungstate supported on Ni foam is fabricated as a binder-free, freestanding electrode via a two-step hydrothermal process followed by partial thermal reduction. By systematically tuning the precursor concentrations of Ni, Co, and W, the morphology and electronic structure of the material are effectively modulated. The introduction of oxygen vacancies through partial thermal reduction plays a key role in enhancing charge transport properties. The optimized NiCo@W_0.5/NF electrode exhibits a porous, flower-like architecture and demonstrates excellent bifunctional electrocatalytic activity toward both UOR and HER, accompanied by improved mass transport behavior. When employed as both the anode and cathode for overall urea electrolysis, NiCo@W_0.5/NF requires a low cell voltage of only 1.68 V to achieve a current density of 100 mA cm⁻² and delivers impressive operational stability in an optimized electrolyte composed of 3 M KOH and 0.33 M urea. These results indicate that NiCo@W_0.5/NF is a highly promising and efficient bifunctional electrode material for urea assisted hydrogen production. Full article

A major quality challenge in the application of titanium alloys is the persistence of substances known as “hard-alpha inclusions”. Although hard-alpha inclusions are extremely rare and typically small in size in high-quality titanium alloys for aero-engine disks, their hard and brittle nature poses a non-negligible threat to the structural integrity of the disks. Due to the extreme scarcity of natural hard-alpha inclusions, most previous studies have focused on “synthetic dense hard-alpha particles” rather than “real porous hard-alpha inclusions”, inevitably over-looking the differences between them. In this work, a method of introducing titanium nitride sponge preforms into the electrode preparation step of the smelting process is proposed and implemented, successfully fabricating real porous hard-alpha inclusions in TC4 titanium alloy disks. On this basis, the detection characteristics of ultrasonic non-destructive testing for such porous hard-alpha inclusions are investigated, and a probability of detection (POD) model for these defects is established for the first time. A defect distribution model of porous hard-alpha inclusions for the probabilistic damage tolerance assessment of disks is also derived. This work reveals that, unlike the “linear” behavior of traditional models, the new defect distribution model adheres to a “cubic polynomial” relationship. Full article