Search Results (1,524)

During the installation of prefabricated vertical drains (PVDs) in soft soil foundations, the smear effect induced by mandrel shoe penetration can severely damage the soil structure and reduce permeability, thereby becoming a key factor restricting foundation consolidation efficiency. Previous studies have generally neglected the smear disturbance caused by the geometry of the mandrel shoe. Although existing studies have conducted numerical and theoretical analyses on the smear effect induced by PVD installation, most of them are still based on equivalent circular simplifications and are therefore unable to characterize the anisotropic disturbance induced by a triangular mandrel shoe. To address this limitation, a three-dimensional CEL penetration model considering the real triangular geometry was established, and the traditional cavity expansion theory was directionally modified. The effects of penetration rate, geometric angular structure, and soil type of the triangular mandrel shoe on the smear zone were systematically investigated. The results show that, with increasing penetration rate, the near-field peak stress and far-field displacement increase simultaneously; from slow penetration to fast penetration, the near-field peak stress increases by approximately 42%. By quantitatively defining the critical threshold corresponding to a sharp 50% attenuation in radial displacement as the boundary of the strong smear zone, it was found that increasing the size of the mandrel shoe significantly amplifies the geometric corner effect, and the near-field disturbance range increases by about 21% compared with that of the small-sized case. The larger the size, the more pronounced the anisotropic disturbance characteristics become: the stress concentration effect and displacement splitting in the vertex direction are further enhanced, causing the disturbance range in that direction to far exceed that in the side direction. Soil properties are the key medium parameters controlling the smear zone. Owing to its relatively high stiffness index and skeleton strength, Clayey Silt shows the largest displacement range, whereas Common Clay exhibits the smallest smear zone because of its stronger structural constraint. The modified theoretical model agrees well with the CEL numerical simulation results, verifying its effectiveness under conditions that consider the geometric characteristics of the mandrel shoe. This study provides a theoretical basis and numerical support for the structural design of mandrel shoes in soft-ground PVD construction. Full article

Pinus caribaea M. comprises three varieties: hondurensis, bahamensis and caribaea, the latter being crucial to the Cuban forestry industry. This systematic review evaluated some physical–mechanical properties and tracheid biometry of Pinus caribaea M. wood, with particular emphasis on var. caribaea, to identify potential knowledge gaps and followed the PRISMA 2020 guidelines. The investigation was conducted in four databases, including gray literature up to December 2024, and the risk of bias was assessed using a tool adapted from the JBI critical appraisal checklist. A total of 535 studies were identified, of which 75 were included in the review based on the inclusion criteria. It was found that only 17.3% of the selected publications focus on var. caribaea. Most studies evaluate physical properties, with less attention paid to mechanical properties and cell biometry. A downward trend in recent publications was noted for this variety, along with a predominance of the radial direction as a source of variation. A lack of research on mature trees (>30 years) as well as other sources of variation were identified as information gaps. Value ranges for density, shrinkage, modulus of elasticity and modulus of rupture in static bending, compressive strength parallel to the grain, as well as tracheid biometry were synthesized from the available publications for all varieties. It is concluded that var. caribaea is under-researched, and a systematic study is therefore required to optimize its use and industrial impact. Full article

The DIGIT experiment was launched at the Tournemire Underground Research Laboratory (URL) with the aim of determining the effects of temperature on the transfer of tracers mimicking the most mobile radionuclides in the Toarcian clay rock. The properties of this rock are similar to those of the host rocks being considered for a future deep geological repository for high-level radioactive waste (HLW). The experiment involves the monitoring of the interaction between a test water doped with stable halides and deuterium at constant concentration, and the porewater of the Toarcian clay rock under constant ambient conditions, as well as at higher temperature induced by artificial heating. This experiment seeks to partially address questions regarding the potential spread of contaminants during the thermal phase of HL waste packages. Specifically, the in situ experiment aims to evaluate the role of scale effects, thermodiffusion, a process that combines Fick’s law, the Soret effect, and convection in the transfer of radionuclides. This paper is the second part of a companion paper dedicated to predictive calculations and the installation of the experimental device. It presents the main experimental and modeling results obtained since the beginning of the installation and after 20 months of heat at 70 °C. The test was carried out in five phases, finishing with a sampling campaign: a phase 0 called “initial conditions”, followed by a pure diffusion phase (5 months), then three phases in a heated period lasting 1 year and 8 months. In total, 47 rock cores were analyzed, with approximately 170 samples tested by four diffusion methods (radial, outgoing, through and in vapor-phase) to determine the tracer concentrations in the porewater, their water content and their diffusive transport parameters. The results show a decrease in tracer concentrations with distance from the test zone, in the directions parallel and perpendicular to the stratification. The anisotropy of the medium results in greater migration in the direction parallel to the stratification. Thermal properties also confirm anisotropy with a higher thermal conductivity in the direction parallel to the stratification. Finally, an activation energy of 22.9 ± 1.7 kJ·mol⁻¹ could be proposed by NMR for deuterium, indicating diffusion behavior following an Arrhenius law between 30 and 70 °C. The experimental data allowed for the calibration of a 2D axisymmetric numerical model using the commercial finite element software COMSOL Multiphysics^®. The Fick’s law corrected by an Arrhenius law best reproduces the penetration of deuterium and anions. The Soret effect, integrated into certain scenarios, is only significant for anions’ migration, using a fitted Soret coefficient of 0.1 K⁻¹, as proposed in the literature for the Callovo-Oxfordian, the host rock of the Cigéo project in the east of France. The calibration of the simulated data with the experimental data allowed for the characterization of damaged and/or disturbed zones evolving over time. Simulations over 150 years, the duration of the thermal maximum for HLW packages, show that advection—modeled by Darcy’s law—would have a negligible role in this context due to the low permeability of the upper Toarcian. In conclusion, the DIGIT test showed that, for the Upper Toarcian clay rocks at the Tournemire URL in France, diffusion, corrected for the effect of temperature, is the mechanism that characterizes the transport of radionuclide analogues. The study showed that thermodiffusion has a limited influence on deuterium migration but remains significant for anions in the case of a coupling between temperature correction and thermodiffusion. The test also highlighted the impact of temperature on the spatiotemporal development of a damaged and/or disturbed zone. These new and relevant results in the field will need to be confirmed later through additional experiments. Full article

This paper aims to define the optimal microgrid topology for rural electrification based on the lowest total cost by comparing LVAC and LVDC microgrids across three different scenarios. An LVAC radial topology is first designed using mixed-integer linear programming for phase balancing and the shortest path for connections, then implemented with a genetic algorithm to allocate and size solar home systems, forming an LVAC microgrid. Next, an LVDC topology is then derived from the LVAC structure and integrated with solar home systems under three scenarios: (1) using the same solar home system sizes, locations, and quantities as the LVAC microgrid; (2) using a genetic algorithm to re-determine solar home system sizes and locations, forming an LVDC microgrid; and (3) clustering the LVDC topology into nano-grids, each defined by genetic algorithm for solar home system sizing and placement and connected to the main feeder via bi-directional converters. Finally, all LVAC and LVDC scenarios are simulated over a 30-year planning horizon for analysis. A non-electrified village located in Cambodia has been selected for a case study to validate the proposed methods. The results have been obtained and provide a comparison of performance indicators (i.e., costs, energy production, losses, CO₂ emissions, and autonomous energy) among the microgrids (LVAC and LVDC). The LVAC microgrid produced lower total energy losses than the LVDC microgrid in all scenarios. However, when considering environmental impact, LVDC Scenario 2 is preferable. Based on the total cost results, the LVAC microgrid is considered more economical than the LVDC microgrid in each scenario in this study. Full article

The quality of ground surfaces depends largely on the topography of the active surface of the grinding wheel, which, in turn, is determined both by the structure of the grinding wheel and by the conditions of the dressing process. This article proposes a new approach to improving the quality of ground surfaces by optimizing the dressing conditions with diamond rollers, based on the correlation between the roughness of the ground surfaces, the roughness of the cutting surface of the grinding wheel, and the parameters of the dressing process. A comprehensive theoretical–experimental study and modeling of the microgeometry of electrocorundum grinding wheels and the roughness of ground surfaces, depending on the dressing conditions with diamond dressing rolls made of medium- and high-strength synthetic diamonds with a mixed grit size, has been carried out. A complex quality indicator has been defined, determined as the ratio between the roughness of the ground surfaces and the roughness of the cutting surface of the grinding wheels, and models have been constructed for its determination, depending on the dressing conditions. By applying a genetic algorithm, optimal conditions for uni-directional and counter-directional dressing (dressing speed ratio, radial feed rate, the dress-out time and the ratio between the grit sizes of the diamond roller dresser and grinding wheel) have been determined, which ensure a minimum value of the complex quality indicator in combination with minimum roughness of the ground surfaces. Full article

This paper presents the design, simulation, and experimental validation of a novel type of pneumatic rotary positioner that is based on a three-cylinder radial mechanism driven by independently controlled pressures. The system uses standard off-the-shelf industrial components, including pneumatic cylinders, proportional pressure regulators, and a programmable logic controller. In order to obtain angular positioning, a three-phase sinusoidal pressure commutation scheme is adopted, similar to the three-phase electrical motors. Analytical expressions for piston kinematics and torque generation are derived and used to design direct open-loop, open-loop with friction compensation, and closed-loop position control strategies. The technical implementation, with the prototype tested unloaded, can achieve accurate positioning (±3° in open-loop mode with feedforward to ±0.3° in closed-loop mode with PD controller), with very good repeatability on average (<0.5°) and smooth theoretical torque (average 1.4 Nm, with 0.51% ripple) at low speeds (<60 rpm). The experimental prototype was designed as a compact device, having approx. 94 mm diameter and 110 mm depth. When used in open-loop mode, the actuator is connected to the control system using just three pneumatic tubes and thus is completely free of any electromagnetic fields, making it suitable for some environment-critical applications. These advantages promote the proposed positioner as a practical rotary actuator in specialized automation and robotics applications where established electrical servomotors cannot be used. Full article

To design novel heart valve bioprostheses, it is extremely important to predict leaflet failure and fatigue for 10–20 years, as the aortic valve opens and closes approximately 40 million times per year. Most studies devoted to aortic valve leaflets mechanical tests employ uniaxial or biaxial tests, which do not fully and explicitly describe the time-dependent biomechanical behavior of this tissue. The aim of this study was to evaluate the viscoelastic response of porcine pericardium using biaxial tensile tests. Biaxial creep tests were performed on a biaxial test machine to evaluate the circumferential and axial behavior of the porcine pericardium under creep testing, and biaxial stress relaxation was used to complement creep. The results showed that the creep behavior was the same in both directions after 1 s, 60 s, 300 s, 900 s, and 1800 s. After 30 min of creep, deformation in the circumferential and radial directions was 3303 $\times {10}^{-6}$ and 5192.9 $\times {10}^{-6}$, respectively. Stress relaxation tests showed the same behavior as creep. At stress relaxation test after 30 min, the pericardium deformation in the circumferential and radial directions was 15.28 kPa and 9.6 kPa, respectively. The Prony series with Levenberg–Marquardt as the optimizer was used to obtain material parameters to use for finite element analysis. The data obtained during such tests can be employed in numerical FSI simulations of novel aortic valve bioprosthesis long-term performance in a patient’s body. Full article

In response to the significantly reduced efficiency of magnetic coupling wireless charging for unmanned aerial vehicles (UAVs) caused by their high sensitivity to transmitter and receiver coil alignment, as well as landing point errors, a position identification method based on the detection coil-induced voltage fingerprint and embedded neural network regression is proposed. This enables position alignment through a 2D mechanical structure. Firstly, by means of an S–S compensation topology with a bipolar (BP) symmetrical four-detection-coil array deployed at the transmitter, the system effectively suppresses primary direct coupling, ensuring that the position of the receiver coil predominantly determines the detection signals. Secondly, by establishing a voltage fingerprint database during the offline stage and utilizing a multi-layer perceptron–radial basis function (MLP-RBF) regression model, the system achieves high-precision end-to-end positioning and alignment control during the online stage through induced voltage acquisition and data processing. Finally, experiments demonstrate that the proposed method achieves centimeter-level positioning accuracy, with an average error of approximately 1.2 cm and a maximum error of less than 1.8 cm, presenting excellent deployability and engineering applicability. Full article

Arsenic (As) is a ubiquitous and highly toxic metalloid with well-established carcinogenicity. Its accumulation and secondary release from lake sediments pose potential risks to lake ecosystem integrity and human health. Meanwhile, the ongoing intensification of lake eutrophication at the global scale has altered the sources, composition, and environmental behavior of internally derived dissolved organic matter (DOM). These changes have profoundly influenced As mobilization and transformation at the sediment-water interface (SWI). To advance understanding of the regulatory roles and underlying mechanisms of algal dissolved organic matter (ADOM) and submerged macrophyte dissolved organic matter (SMDOM) in As biogeochemical cycling under lake ecosystem regime shifts, extensive findings from the international literature were synthesized. The characteristic properties and environmental behaviors of ADOM and SMDOM were systematically compared, and their distinct regulatory pathways in lacustrine systems were further summarized. Results indicate that ADOM is typically characterized by low molecular weight, weak aromaticity, and high bioavailability. It can enhance As dissolution and mobilization from sediments through direct complexation, competition for adsorption sites, and stimulation of microbial metabolism and Fe(III) reduction. In contrast, SMDOM exhibits higher molecular weight, greater aromaticity, and a higher degree of humification. It tends to form stable complexes with mineral phases. Under the influence of radial oxygen loss (ROL) from submerged macrophyte roots during the growth phase, its capacity to promote mineral reduction is relatively limited. This process favors stable As retention in sediments. The regulatory effects of ADOM and SMDOM on As behavior are strongly modulated by environmental factors such as pH, redox potential (Eh), temperature, and light conditions, as well as by microbial communities. ADOM is more sensitive to reducing environments and photochemical processes. SMDOM, in contrast, exerts more persistent control under oxidizing conditions and at mineral-water interfaces. In addition, ADOM more readily drives microbial community shifts toward assemblages with enhanced capacities for Fe(III) reduction and As reduction or methylation. SMDOM is less likely to trigger strongly reducing processes. Based on these mechanisms, the outbreak and decay phases in algal-dominated lakes often correspond to critical periods of enhanced As mobilization and elevated ecological risk. In submerged macrophyte-dominated lakes, the decay phase may represent an important window for sedimentary As release. Finally, a conceptual framework describing the differential regulation of As biogeochemical cycling by ADOM and SMDOM is proposed. This framework provides a theoretical basis for As risk identification, the determination of critical risk periods, and the development of management strategies across lakes with different trophic states. Full article

This paper introduces a hybrid metaheuristic approach for the reconfiguration of electric distribution networks, integrating Simulated Annealing (SA) and Tabu Search (TS) to accelerate convergence and enhance exploration of the solution space. The method employs a selective mesh-based neighbor generation strategy, which substantially reduces the search space while maintaining operational feasibility (radial topology, voltage, and current limits). The approach was implemented in Python and integrated with DIgSILENT PowerFactory, enabling the direct evaluation of losses, voltages, and currents for reproducible and scalable analysis. Validation on 5-, 16- and 33-bus benchmark systems consistently reached the global optimum across 100 simulation runs, demonstrating robustness and computational efficiency. A real-world application was performed on the 10 kV primary distribution network of Huancayo, Peru, where the proposed method achieved a 10.4% reduction in active losses, improved the minimum voltage from 0.931 to 0.949 p.u., and partially relieved feeder overloads. These results confirm the method’s suitability for both academic benchmarking and practical deployment in Latin American distribution systems. Full article

Vibration-assisted water flooding (VA-WF) can improve sweep efficiency. However, unclear macro-scale mechanisms limit its wider adoption in heavy oil reservoirs. This study combines previous sandpack experiments with two-dimensional Volume-of-Fluid (VOF) simulations to show how vibrations reshape permeability fields and, in turn, pressure and production behaviour. Heavy oil sandpacks were water-flooded under conditions of no vibration and 2 Hz and 5 Hz axial excitation. Measured injection pressure histories and oil production were used to calibrate a VOF model in which absolute permeability follows a log-normal distribution with directional anisotropy. Only when axial and radial permeabilities were assigned a negative local correlation did the model reproduce key observations: secondary pressure spikes, irregular viscous-fingering morphologies, delayed production drops, and variability in cumulative recovery. Parameter sweeps quantify the sensitivity of VA-WF performance to the variance and correlation of the permeability field, and multiple runs estimate the variability in outcomes introduced by stochastic heterogeneity. This study proposes a transferable workflow—comprising sample testing, parameter inference, and probabilistic simulation—to screen excitation conditions and forecast VA-WF performance prior to field implementation, enabling operators to optimize vibration frequency based on reservoir-specific permeability characteristics and to anticipate production variability under uncertainty. These results highlight the dominant factors affecting swept volume and oil recovery, supporting data-driven decision making in VA-WF projects. Full article

To investigate the mechanism of texture formation during the cold rolling of Ti-3Al-2.5V tubes for aerospace hydraulic systems, this study examines the microstructure at various locations of two deformation cones with ‘Q’ ratios of 1.055 and 1.300, respectively, in a single cold-rolling pass, revealing their continuous texture evolution. The results indicate that the cold-rolling texture primarily forms during the sinking section. A higher ‘Q’ ratio leads to a stronger tendency for the c-axis of grains to align parallel to the radial direction of the tube, resulting in enhanced radial texture intensity. Beyond influencing texture through dislocation slip, a higher ‘Q’ ratio also elevates the Schmid factor for {10$\stackrel{\mathrm{-}}{1}$2} twinning. This twinning mechanism primarily forms the radial texture by altering the stress state. Consequently, this change not only facilitates twin activation but also modifies the rotation direction of grains during the twinning process. Compared to the cone with a ‘Q’ ratio of 1.055, the deformation cone with a ‘Q’ ratio of 1.300 contains a greater number of twins oriented along <0001>//RD, leading to a stronger radial texture in the tube. Full article

Carbon nanotube yarns (CNTYs) have received more consideration recently due to their excellent specific mechanical, electrical and thermal properties, making them promising materials for different applications. Until now, the axial properties of the yarn have been thoroughly investigated; however, the transverse or radial properties, orthogonal to the fiber axis, remain relatively unknown due to the challenges associated with their measurement. In this study, the transverse or radial response of the CNTY including its elastic modulus was determined using Atomic Force Microscopy (AFM) and Raman Spectroscopy. Determining transverse properties in fibrous materials presents challenges owing to their geometry, inherent anisotropy, whereby mechanical characteristics exhibit directional disparities; i.e., the properties in the transverse direction may be several orders of magnitude smaller than those in the axial direction. To overcome these difficulties, AFM was utilized to perform nanoindentation experiments, where a tipless flexible cantilever probe was used to apply a controlled force to the CNTY surface. The resulting indentation depth was then analyzed to determine the transversal elastic modulus. Preliminary findings indicate that the transverse elastic modulus of the CNTYs ranges from 10–54 kPa for strain levels below 3%. Complementary Raman spectroscopy provided insight into the bulk-scale mechanical behavior of CNTYs. Incremental compressive loading between microscope slides induced nonlinear upshifts in the 2D Raman band (from ~2686.6 to 2691.4 cm⁻¹), indicating nanoscale tube realignment, inter-tube densification, and compaction. From lateral diameter measurements under load, a stress–strain curve was constructed, revealing three distinct regimes: one with an initial elastic modulus of 3.12 MPa (0.3–11.2% strain), another one with an elastic modulus increasing to 8.46 MPa (11.2–14.4%), and finally one with an elastic modulus peaking at 16.86 MPa beyond 14.4% strain. Together, these methods delineate the hierarchical and anisotropic nature of CNTYs, validating the importance of multiscale mechanical characterization for their deployment in piezoresistive sensors and multifunctional composites. This study establishes a robust framework for quantifying the transverse mechanical response of CNTYs. Full article

Radial and ulnar fractures in toy-breed dogs are associated with a high risk of complications due to limited bone stock and soft tissue coverage. The aim of this retrospective study was to evaluate the postoperative clinical and radiographic outcomes in dogs undergoing radial and ulnar fracture stabilization with a titanium locking mini-plate system. Medical records and radiographs of toy-breed dogs weighing ≤5 kg treated between 2020 and 2025 were reviewed. Twenty-six dogs met the inclusion criteria. Radiographic union after primary fixation was observed in 92.9% of fractures. Implant failure occurred in 7.1% of cases and was successfully addressed with revision surgery, after which fracture healing was achieved. At final follow-up, limb function was graded as excellent in all dogs, including those requiring revision surgery. A shorter distal fragment length was significantly associated with implant failure, whereas implant length and proximal fragment length showed no significant association. These findings indicate that titanium locking mini-plates were associated with favorable clinical and radiographic outcomes. Distal fragment dimensions may influence the risk of implant failure and should be considered during surgical planning. However, the small number of implant failure events limits the robustness of statistical inferences, and the absence of a control group prevents direct comparison with alternative fixation techniques. Full article

A novel shallow oil chamber hybrid journal bearing with adjustable oil chamber depth was designed based on piezoelectric ceramics, inspired by conventional shallow oil chamber bearing structures. The computational fluid dynamics method is used to analyze the bearing characteristics of shallow oil chamber bearings, including the volume flow, the seal oil pressure, load capacity and stiffness. An experimental platform equipped with signal acquisition device and piezoelectric ceramic control device was developed. The eddy current sensors collected the displacement signal at the shaft end. The required voltage was calculated by the displacement signal. The piezoelectric ceramics elongated or shortened, causing a displacement of the same magnitude in the depth of the oil chamber, thereby controlling the radial displacement of the shaft. The adjustment effect of this bearing was verified by experiment for no-load and 500 N load at 200–1000 rpm, with a baseline initial oil chamber depth of 20 and an oil supply pressure of 2 MPa. The results showed that compared with the case without adjustment, the accuracy in Y direction has increased from 8.9 μm to 1.9 μm (max. 78.4%) after adjustment. Under the above load conditions, the displacement can be controlled below 2 μm, indicating a significant improvement in shaft vibration resistance. Full article