Search Results (4,220)

This study aims to investigate the static performance of water-lubricated rubber bearings (WLRBs) with axial grooves. To achieve this objective, an analytical approach is employed that combines a modified Reynolds equation, accounting for surface groove effects and rubber deformation, with a Winkler model and finite element analysis of pressure distribution. By developing a fluid–structure interaction model that incorporates rubber liner deformation, this research reveals the interaction between WLRB geometry and steady-state performance parameters. The investigation evaluates the influence of geometric characteristics, including groove shape, number, and size, on the performance of elastomeric liner WLRBs, while assessing optimal groove depths under various conditions. The study analyzes five distinct groove geometries, including semi-cylindrical, rectangular prism, and three pyramidal types with different apex positions, in a six-groove bearing configuration, presenting their qualitative effects on the behavior of the examined bearings. The key findings indicate that increasing groove size or quantity reduces maximum pressure and load-carrying capacity while elevating friction coefficients. As groove count rises, supporting surfaces diminish, causing pressure distribution to intensify and minimum film thickness to decrease under a specified external load. A notable result reveals that when groove depth exceeds film thickness, performance becomes geometry-independent; however, shallower grooves exhibit significant geometric effects. Additionally, the study identifies groove ends as critical functional zones where film thickness reduction substantially enhances pressure distribution and static performance. Comparative analysis shows that longitudinal grooves with triangular cross sections outperform semi-circular and rectangular variants, with the backward triangular configuration demonstrating superior characteristics due to optimal end-film properties. In conclusion, this research provides a detailed understanding of how groove geometry influences the static performance of WLRBs, highlighting the importance of groove design, particularly at the groove ends, in optimizing bearing functionality. The findings offer valuable insights for the design and selection of groove configurations in water-lubricated rubber bearing applications. Full article

With the changing demands of society, gears, as fundamental components of mechanical devices, are evolving towards higher reliability and longer service life. To address the issue of thermal scuffing at the gear meshing interface, we propose the introduction of micro/nano-textures to improve the thermal elastohydrodynamic lubrication characteristics of the meshing surfaces, thereby enhancing the lubrication performance and anti-scuffing load capacity of the gear surfaces. First, finite element models with different microstructural features were established. Then, numerical calculations were conducted using computational fluid dynamics (CFD) software to analyze the impact of various micro-texture configurations on the lubrication performance of the tooth surface. Finally, an orthogonal experiment was performed to optimize the groove length, groove width, and areal density of the micro-textures in order to obtain the best processing parameters. The results show that, compared with the triangular, rectangular and trapezoidal micro-textures, the wedge-shaped micro-texture produces the largest pressure difference at the meshing-in and meshing-out points of the texture grooves, which causes the dynamic pressure effect to be more obvious. Compared with the triangular, rectangular and trapezoidal micro-textures, the wedge-shaped micro-texture has the largest bearing capacity and the smallest friction coefficient, so it has better bearing capacity and anti-friction and wear performance. The process parameters were optimized through orthogonal experiments, and the optimal combination of process parameters was obtained as the areal density of 50%, the depth of micro-pits of 12 µm, and the width of micro-pits of 200 µm. Under these optimal parameters, the pressure difference at the meshing-in and meshing-out points of the wedge micro-texture increased significantly by 255.6% compared to the initial model, and the oil film friction coefficient decreased by 17.857% relative to the initial model. These results demonstrate that the micro-texture with optimal parameters significantly enhances the lubrication and anti-friction/wear performance of the tooth surface. Full article

In structural engineering practice, the problem of thick plate bending occurs in designing shelters, foundations of high-rise buildings, counter-slabs, etc. In such cases, neglecting shear deformation can lead to significant errors in predicted behavior, especially when a plate is subjected to a concentrated force. In practice, neither a fully clamped nor an ideal simple support can be achieved during construction, so the plates are partially clamped, and this also applies to thick plates. Bending of thick rectangular plates with partially clamped edges has not been studied in the literature, so this paper addresses this issue. A comprehensive numerical analysis using a developed simple analytical model in the form of a Lévy-type solution based on Reissner theory has been carried out. The presented model is able to account for different degrees of rotational restraint in plates with two opposite edges simply supported and the other two partially clamped by introducing the fixity factor. The obtained results are compared with those available in the literature, as well as with a numerical FEM model, whereby good agreement is observed. The significant difference when using the proposed model to analyze a thick plate, as opposed to the models based on Kirchhoff theory, is underlined. Full article

This study presents a simulation-based evaluation of a wall-following and mapping framework for autonomous underwater vehicles (AUVs) equipped with a single-line laser, targeting structured environments such as rectangular tanks and dam interiors. A hardware-in-the-loop (HIL) simulation platform is developed to integrate sensor emulation, vehicle dynamics, and image-based control while preserving the onboard data formats, update rates, and communication protocols of the AUV system. Using a single camera–laser pair, the framework estimates yaw angle and lateral wall distance from laser image geometry to support real-time wall-following and frontal obstacle avoidance. Wall mapping is performed by transforming laser image features into spatial coordinates and estimating the dimensions of geometric protrusions. The framework is evaluated on simulated walls with protruding features under two navigation conditions: ideal-motion and dynamic-control operation. Simulation results show stable wall-following performance, with lateral distance errors typically below 0.1 m. Under ideal-motion conditions, mapping errors range from 1% to 13%, while under dynamic-control navigation they increase to 10–35% due to attitude fluctuations and control-induced motion. Frontal obstacle avoidance maintains a minimum clearance of 1.04 m. The results demonstrate the feasibility of using a single-line laser and a unified image stream for both real-time wall-following control and post-mission geometric mapping within the defined simulation conditions. While the evaluation is limited to simulation and assumes idealized optical conditions without modeling hydrodynamic disturbances or optical degradation effects, the framework provides a system-level reference for laser-guided inspection strategies in confined underwater environments such as tanks, reservoirs, and dams. Full article

Proton exchange membrane water electrolyzers (PEMWEs) are an emerging hydrogen production technology with significant advantages. However, their structural design remains incompletely matured. During assembly, the clamping force is transmitted through the endplate to internal components. Improper clamping force causes uneven stress distribution across electrolysis cells, compromising sealing integrity and hydrogen production efficiency. To address uneven force transmission in conventional rectangular endplates, this study proposes a curved stack-facing endplate structure. A multi-objective optimization methodology is employed to identify the optimal curvature radius, which provides pre-deformation compensation during operation. This enables the surface to flatten under clamping force and to ensure tight contact with underlying cells. After optimization, the standard deviation of deformation along each path on the single electrolysis cell decreased by over 10% and the standard deviation of equivalent stress along each path on the endplate dropped by more than 5%. Subsequently, an orthogonal experimental design considering curvature radius and bolt arrangement is conducted to find the optimal combination in stack assembly. The optimal combination is identified and compared with the stack equipped with the original rectangular endplate. The maximum deformation at the four corners of the optimized endplate decreases from 0.28399 mm to 0.27452 mm. Additionally, the stress concentration area in the optimized endplate is reduced by more than half. Results demonstrate significantly reduced stress concentration and substantially more uniform stress distribution in the optimized endplate. Full article

The aim of this study was to evaluate the influence of prosthetic substrate type, resin cement shade, and opaquer liner application on the translucency and color matching of translucent zirconia- and lithium-based ceramics. Four A2-shade zirconia materials (Katana HTML Plus, STML, UTML, and YML), with and without an opaquer liner, lithium disilicate ceramics (Amber Mill LT and HT), and zirconia-reinforced lithium silicate (Celtra Duo) were investigated. Monolithic crowns and standardized rectangular specimens were fabricated using CAD/CAM technology and cemented with neutral, warm-shade, and opaque try-in pastes onto A2-shade composite resin and cobalt–chromium substrates. Color measurements were performed using a digital colorimeter based on the CIE L*a*b* system. Translucency parameters (TPs) and color differences (ΔE) relative to the A2 reference shade were calculated. Lithium-based ceramics exhibited significantly higher translucency than zirconia materials. Application of the opaquer liner on intaglio surface of crowns reduced their translucency. On A2-shade substrates, translucent zirconia luted with neutral or warm-shade paste demonstrated the most favorable color compatibility. In contrast, opaque try-in paste resulted in clinically unacceptable color deviations and loss of optical depth. On metallic substrates, most materials exhibited pronounced gray discoloration and substantial color mismatch, particularly lithium disilicate ceramics. These findings indicate that ceramic type, substrate color, opaquer liner application, and resin cement shade significantly influence the optical performance and final color outcome of all-ceramic restorations. Full article

In this article, a new approach to the applicability of the self-complementarity concept in a classical two-port microstrip patch antenna element is presented. This was accomplished through an illustrative design and an electromagnetic analysis of a broadband two-port rectangular printed radiating element in transmission configuration. A calculated ultra-wide matching bandwidth up to approximately 11 GHz was achieved (BW_{sim-RL≥10 dB} ≈ 11 GHz, f_o = 5.5 GHz, i.e., BW_{sim-relative-matching} ≈ 200%). One of the advantages of this topology is that only two degrees of freedom are needed to acquire a very wide impe-dance bandwidth: the length and the width of the slot. Full-wave analysis shows that sui-table combinations of the patch and slot dimensions allow to obtain the broadband mat-ching behavior. It has broadside radiation toward both hemispheres, which is conserved and considerably stable over a wide frequency range. Its linear polarization, radiation patterns, gain values, and radiation efficiency are adequate from 1 to 8 GHz (BW_{sim-radiation} ≈ 7 GHz, f_{o [sim-rad]} = 4.5 GHz, i.e., 63.6% of its BW_sim-matching, and 156% of its f_{o [sim-rad]}). Moreover, the gain and radiation efficiency exhibit very good flatness across wide frequency ranges. Measurements of S-parameters and radiation patterns validate the calculated results. The proposed antenna element is simple, compact, and light-weight. It has a very wide ope-ration bandwidth (7 GHz), its design is easy and flexible, and it is simple to manufacture. It could be used as a radiating element in different linear polarized antenna arrays. Full article

This study numerically investigates heat transfer and thermodynamic behavior in twisted square and rectangular air ducts while keeping a constant hydraulic diameter (D_h = 30 mm). Three aspect ratios are considered (AR = 1.00, 0.75, and 0.50). The heated test section (900 mm) is divided into three equal segments, and three pitch patterns are examined: a uniform pitch (400–400–400 mm, P444) and two axial gradients (300–400–500 mm, P345; 500–400–300 mm, P543). All results are compared to a standard reference, the straight square duct (SD-AR1.00), to ensure fair comparisons across all cases with Reynolds numbers between 5000 and 20,000. Among the twisted ducts, the strongest rectangularity combined with the increasing pitch sequence, TSD-AR0.50-P345, provides the best overall balance. Its heat transfer rises from Nu = 39.39 to 88.62, giving Nu/Nu₀ = 1.493 → 1.433, while the pressure penalty increases to f/f₀ = 1.345 → 1.405. Under cube-root weighting of friction, this case maintains the highest thermal performance factor, TPF = 1.352 at Re = 5000 and TPF = 1.279 at Re = 20,000. Second-law trends support the same ranking: exergy destruction decreases from 12.81 W (baseline) to 8.44 W at Re = 5000 (≈34% reduction) and from 6.54 W to 4.84 W at Re = 20,000 (≈26% reduction). The Bejan number remains high at low Reynolds numbers (≈0.998), indicating heat-transfer irreversibility dominance, but drops at higher Reynolds numbers (≈0.87) as frictional effects become more important. In general, the results show that adding a small axial pitch increase to rectangularity can improve near-wall mixing while reducing losses downstream. This leads to a clear improvement in both first-law performance and exergy-based measures. Full article

Freeform Fresnel lenses combine the powerful beam-shaping capability of freeform optics with the lightweight and compact characteristics of conventional Fresnel structures, leading to their increasing adoption across diverse applications. This paper proposes and experimentally validates a method for generating rectangular dark hollow beams using a freeform Fresnel lens. The lens is divided into multiple fan-shaped sectors centered on the optical axis, with each sector generating a defocused spot at a distinct spatial location. Based on geometrical optics, a freeform Fresnel lens with a 25 mm aperture is designed to produce a square hollow beam with a side length of 10 mm. A lens with a division angle of 5° was fabricated using ultra-precision diamond turning. The angular form error was measured to be below 0.1°, and the surface roughness was found to be below 10 nm. An optical testing system was established to characterize the generated beam profile. The experimental results successfully demonstrate the formation of the desired rectangular dark hollow beam. The measured results agree well with the simulations, confirming the feasibility and practical potential of the proposed method. Full article

The breeding blanket is a key component of tokamaks, primarily responsible for extracting heat from fusion reactions and for tritium breeding, which is essential to ensure a fusion reactor’s fuel self-sufficiency. Recent technological advancements have led to the development of Dual-Cooled Lead–Lithium (DCLL) breeding blankets, which employ a liquid metal (specifically a Lead–Lithium eutectic alloy) as a heat transfer medium and tritium breeder, while helium gas is used to cool the structural components of the reactor. The interaction between the moving electrically conducting fluid and the strong magnetic field in the tokamak environment leads to magnetohydrodynamic (MHD) effects. The latter are characterized by the induction of eddy currents within the fluid and resulting Lorentz forces generated by their interaction with the magnetic field, which cause additional pressure losses and reduce heat transfer efficiency. This work investigates the pressure drop experienced by a Lead–Lithium flow within a rectangular section conduit under the action of an external, uniform magnetic field of different intensities. An analytical model was developed to estimate the total MHD-induced pressure losses along the channel for different values of the external magnetic field intensity and then benchmarked against relative computational fluid dynamics (CFD) simulations carried out using COMSOL Multiphysics. This comparison allowed the validation of the analytical predictions as well as a better understanding of the influence of the applied magnetic field intensity on the overall pressure drop. Therefore, the aim of the analytical model is to provide analytical tools for reasonably accurate estimations of MHD pressure losses suitable for future preliminary design purposes. Full article

Craniosynostosis is the premature fusion of skull bones due to loss of stem/progenitor cells located in non-mineralized tissue between growing cranial bones of infants. We generated scaffolds from a biodegradable biomaterial with small interconnected pores (125–250 μm diameter), previously shown to maintain stemness of a mesenchymal cell population, to further develop a method for the creation of an artificial cranial bone stem cell niche. Polymer scaffolds of consistent pore size were fabricated using a molecular-sieved sugar sphere casting technique with poly-l-lactic acid. A rectangular surgical defect within the parietal bone of juvenile mice was created. The three groups included sham animals with surgery but no scaffold, experimental animals with surgery plus an implanted cell-free scaffold, and experimental animals with surgery plus an implanted bone mesenchymal cell-seeded scaffold. Healing at the surgical site was evaluated at 4 and 12 weeks after surgery by micro-CT and histology. Surgical site bone volume fraction and bone mineral density were significantly greater at twelve than four weeks in the sham group but not in either of the scaffold groups. At twelve weeks, the surgical site bone volume fraction and bone mineral density were significantly lower in the cell-seeded scaffold as compared to the sham animal group. At twelve weeks, the anterior and middle cranial vault widths were significantly greater in the cell-seeded scaffold as compared to the sham animal group on the surgery side of the skulls. Less mineralization was evident within the cell-seeded than the cell-free scaffolds by histology. Based on these findings, scaffolds of sufficiently small pore size seeded with autologous bone mesenchymal stem cells could function as an artificial cranial stem cell niche to inhibit surgical-site mineralization and promote cranial growth. Full article

Reinforced concrete (RC) structures in marine environments face severe durability challenges due to chloride-induced corrosion. This study investigates the corrosion mechanism and degradation of axial compressive performance in RC columns under the combined effects of sustained loading and corrosion, taking the permanent–temporary integrated RC columns of the Pinglu Canal project as an example. The experimental variables included different sustained load levels and degrees of corrosion. Twelve rectangular RC columns were designed and tested. A specialized setup was developed to simultaneously apply sustained load and induce corrosion to the columns, while monitoring their creep deformation. The columns were subjected to accelerated electrochemical corrosion in a 5% NaCl solution, concurrently under sustained loads of 0, 0.3, and 0.6 times their designed axial compressive capacity, with exposure durations of 0, 30, 60, and 120 days, respectively. The study examined the effects of sustained load level and corrosion degree on the failure mode, concrete creep deformation, and load–displacement curves of the corroded RC columns. The results indicated that sustained loading shortened the duration of concrete expansion deformation and reduced its peak value. Furthermore, the expansion deformation of concrete delayed the creep of corroded columns by 25 to 35 days; after the expansion recovery, the creep rate increased significantly. For corroded columns without sustained loading, the ultimate bearing capacity decreased by 32.0% to 47.8%, with degradations in both stiffness and ductility. The application of sustained loading alleviated the degradation in the ultimate bearing capacity and stiffness of the corroded columns but exacerbated the degradation of their ductility. Finally, considering the effects of concrete expansion deformation and steel corrosion, a predictive model for the creep of RC columns under the coupled action of sustained loading and corrosion was proposed, aiming to provide a theoretical basis for the durability design and maintenance of RC structures in the Pinglu Canal project. Full article

Unmanned aerial vehicles, which are widely used today, require human assistance to meet their energy needs. This dependency disrupts autonomous operation. At this point, wireless power transfer technology offers a promising solution for full autonomy. These vehicles can be easily charged by contactless power transfer between magnetic couplers in seemingly impossible locations. Coupler configurations are critical due to the size constraints of these vehicles. In current studies, analyses of transfer efficiency are conducted using one or two parameters. In this study, in addition to the coupler configuration, the effects of air gap, duty cycle, and magnetic core on efficiency were analyzed together. The performance of couplers with rectangular, circular, and double-D configurations was investigated through comprehensive simulations and experiments. The AC and DC efficiencies of the wireless power transfer system were analyzed by performing 46 experiments, while the operating frequency of the system was between 95 and 105 kHz, the input power was around 250 W. Simulations of the system and couplers were performed in MATLAB and Ansys. In the experiments, the highest AC efficiency was 98.9%, and the DC efficiency was 86.7%. The error margins in MATLAB and Ansys models are less than 1% and 4%, respectively. Full article

Magnetic fluid sealing is an ideal solution for high-end equipment. However, traditional rectangular pole teeth suffer from low magnetic flux utilization and insufficient pressure resistance. Meanwhile, the pressure transmission mechanism of different pole teeth and the evolution law of magnetic fluid boundary morphology remain unclear, restricting structural optimization. This study investigates rectangular and trapezoidal pole teeth by adopting the Volume of Fluid model, combined with finite element simulation and experimental verification. A sealing simulation model and a dedicated experimental platform were established to systematically explore the effects of the two pole tooth types on pressure transmission efficiency and magnetic fluid boundary morphology under static and dynamic sealing conditions, as well as their pressure resistance and self-recovery characteristics. Results show that trapezoidal pole teeth exhibit superior pressure resistance to rectangular ones due to optimized magnetic field distribution: the maximum static sealing pressure resistance increases by 40.9 kPa, and the dynamic sealing pressure resistance at 8000 rpm rises by 63.2 kPa. The 2% deviation between simulation and experimental data verifies the model’s reliability. This work clarifies the intrinsic relationship between pole tooth structure and sealing performance, reveals the pressure transmission mechanism of different pole teeth, and provides theoretical and engineering references for pole tooth structural optimization, which is significant for improving the pressure resistance stability and engineering applicability of magnetic fluid sealing. Full article

This article investigates the numerical solution of the two-dimensional Poisson equation defined over a rectangular domain subject to a double integral nonlocal boundary condition. We propose a finite difference scheme by discretizing the integral term using the two-dimensional trapezoidal rule. The main difficulty of this problem is that, in the non-classical case, we cannot use the method of separation of variables and decompose the problem into one-dimensional problems. Our approach involves reducing the integral boundary condition from the complete domain to the interior points and strategically partitioning the computational domain into the boundary and interior points. We propose a method that allows us to find a solution by solving the Poisson equation with classical boundary conditions, and using the solutions found to construct a solution to a problem with a nonlocal integral condition. This method requires solving a linear system whose dimension is much smaller than the original. Under certain conditions on the kernel, the proposed method is correct. Full article