Search Results (360)

This study developed a gas chromatography–tandem mass spectrometry (GC-MS/MS) method for detecting dinotefuran residues in fruits and vegetables. The modified extraction procedure employed solvent conversion for GC-MS/MS compatibility, achieving a linear range of 0.001–2.0 mg/kg (r² > 0.999), a LOD of 0.003 mg/kg, and a LOQ of 0.01 mg/kg. Recovery rates ranged from 88.2% to 104.5% (RSD: 3.5–5.8%). The analysis of 18 commercial samples from Weifang, China, revealed the highest residues in nectarines (0.12 mg/kg) and lowest residues in cucumbers (0.02 mg/kg), with the dietary exposure risk assessment indicating hazard quotients well below safety thresholds. The literature review showed that dinotefuran has a shorter soil half-life (10–30 days) than most neonicotinoids, a low adsorption coefficient (Koc 30–50), high leaching potential, and significant toxicity to pollinators (LD₅₀ = 0.023 μg/bee). The validated method provides reliable detection across diverse matrices, while the environmental behavior analysis highlights the need for the careful management of dinotefuran applications to minimize ecological impacts despite its favorable degradation profile compared to other neonicotinoids. Full article

The development of highly selective and sensitive gas sensors is essential for detecting toxic pollutants, such as carbon monoxide (CO), which pose severe health and environmental risks. In this work, the adsorption of CO molecules on Ni_6−xCu_x (x = 0–6) clusters supported on hexagonal boron nitride quantum dots with nitrogen vacancies (h-BN_VQDs) is explored through density functional theory (DFT) calculations. For this purpose, the stability of the metallic clusters supported on the boron nitride sheet was calculated, and the adsorption properties of the CO molecule on the Ni_6−xCu_x (x = 0–6)/h-BN_VQDs composite were determined. The results demonstrated a high binding energy between Ni_6−xCu_x (x = 0–6) clusters and the h-BN_VQDs sheets, suggesting that Ni-Cu clusters are highly stable on h-BN_VQDs sheets. For CO adsorption, adsorption energy and charge transfer calculations indicated that the Ni₆ and Ni_6−xCu_x (x = 2 and 3) clusters exhibit the strongest CO binding and highest charge transfer, suggesting them as good candidates for CO gas sensing. These findings provide theoretical insights into the rational design of bimetallic catalysts for gas-sensing applications. Full article

Carbon dioxide (CO₂) is a non-toxic asphyxiant gas that, once released, can pose severe risks, including suffocation, poisoning, frostbite, and even death. As a critical component of carbon capture, utilization, and storage (CCUS) technology, CO₂ pipeline transportation requires reliable leakage detection and precise localization to safeguard the environment, ensure pipeline operational safety, and support emergency response strategies. This study proposes an inversion model that integrates wireless sensor networks (WSNs) with the Gaussian plume model for CO₂ pipeline leakage monitoring. The WSN is employed to collect real-time CO₂ concentration data and environmental parameters around the pipeline, while the Gaussian plume model is used to simulate and invert the dispersion process, enabling both leak source localization and emission rate estimation. Simulation results demonstrate that the proposed model achieves a source localization error of 12.5% and an emission rate error of 3.5%. Field experiments further confirm the model’s applicability, with predicted concentrations closely matching the measurements, yielding an error range of 3.5–14.7%. These findings indicate that the model satisfies engineering accuracy requirements and provides a technical foundation for emergency response following CO₂ pipeline leakage. Full article

Perfluoroalkyl and polyfluoroalkyl substances (PFASs) are a class of synthetic organic compounds with extremely high chemical stability and environmental persistence that are widely used in the industrial sector and in consumer goods. Their strong C-F bonds make them difficult to degrade, meaning they can migrate through the atmosphere and settle over long distances, posing long-term risks to the global ecological environment and human health. This article systematically reviews the classification, physicochemical properties, concentration levels, spatial distribution, migration and transformation behaviors, and health and ecological impacts of PFASs in the atmosphere, along with related analytical detection techniques and pollution control methods. Studies show that short-chain PFASs are more likely to migrate through the atmosphere due to their high water solubility and volatility, while long-chain PFASs tend to be adsorbed onto particulate matter and display stronger bioaccumulation. Although atmospheric research on PFASs lags behind that focused on their dynamics in water and soil, the existing data still reveal a difference in their distribution and regional pollution characteristics in the gas and particle phases. Toxicological studies have confirmed that PFAS exposure is associated with liver injury, immunosuppression, developmental toxicity, and cancer risk and can threaten ecological security through the food chain. Currently, governance technologies are confronted with the challenges of low efficiency and high cost. In the future, it will be necessary to combine multi-media models, new analytical techniques, and international collaboration to promote the development of source control and innovative governance strategies. Full article

With the development of the mining industry, safety issues in underground operations are becoming increasingly relevant. Complex gas conditions in mines, including the presence of explosive and toxic gases, pose a serious threat to the lives of miners and the stability of production processes. This paper describes the development and modeling of an integrated fire monitoring and automatic extinguishing system that combines gas collection, concentration analysis, and rapid response to emergencies. The main components of the system include the following: a gas collection module that uses an array of highly sensitive sensors to continuously measure the concentrations of methane (CH₄), carbon monoxide (CO), and hydrogen sulfide (H₂S) with an accuracy of up to 95%; a gas analysis module that uses data processing algorithms to identify gas concentration threshold exceedances (e.g., CH₄ > 5% vol. or CO > 20 ppm); and an automatic fire extinguishing module that activates nitrogen supply, ventilation, and aerosol/powder fire extinguishers when a threat is detected. Simulation results in MATLAB/Simulink showed that the system reduces the concentration of hazardous gases by 30% within the first 2 s after activation, which significantly increases safety. Additionally, scenarios with various types of fires were analyzed, confirming the effectiveness of the extinguishing modules in mines up to 500 m deep. The integrated system achieves 95% gas detection accuracy, 90 ms response latency, and 40% hazard reduction within 3 s of activation, verified in 500 m deep mine simulations. Quantitative comparison shows a 75% faster response time and 10% higher detection accuracy than conventional systems. The proposed system demonstrates high reliability in difficult conditions, reducing the risk of fires by 75% compared to traditional methods. This work opens up prospects for practical application in the coal industry, especially in regions with a high risk of spontaneous coal combustion, such as India and Germany. Full article

Polystyrene microfragments are among the most common plastic pollutants globally. They significantly affect aquatic life, harming various organs and tissues. In this study, we examined the effects of 3 µm polystyrene beads (MPs, 20 µg/L) on development and yolk resorption in pre-feeding nauplii of Artemia salina, a lecithotrophic crustacean used in toxicity testing. Results showed a reduced hatching rate, slower growth, and the onset of oxidative stress. Histological analysis revealed no significant morphological alteration; however, yolk platelets lost N-acetyl galactosamine (galNAc), and resorption was delayed. Lectin staining also showed a reduction in N-acetyl glucosamine (glcNAc) in the gut brush border, indicating impaired gut function. Gas chromatography detected the release of nanogram amounts of toxic volatile compounds (VOCs, ethylbenzene, xylene, benzaldehyde, and styrene) into the culture medium. In conclusion, the data demonstrate a delay in larval yolk resorption that can likely be attributed to the release of VOCs, which induce oxidative stress. Further research is urgently needed, given the potential biological and ecological implications of this finding. Full article

Polycyclic aromatic hydrocarbons (PAHs) are increasingly recognized as a major contributor to the occupational cancer risk among firefighters. In response, the National Fire Protection Association (NFPA) and other regulatory bodies have recommended rigorous decontamination protocols to minimize PAH exposure. Despite these efforts, a critical gap persists: the absence of real-time, field-deployable devices capable of detecting these invisible and toxic compounds during firefighting operations or within fire stations. Additionally, the lack of effective and optimized methods for the removal of these hazardous substances from the immediate environments of firefighters continues to pose a serious occupational health challenge. Although numerous studies have investigated PAH detection in environmental contexts, current technologies are still largely confined to laboratory settings and are unsuitable for field use. This review critically examines recent advances in PAH decontamination strategies for firefighting and explores alternative sensing solutions. We evaluate both conventional analytical methods, such as gas chromatography, high-performance liquid chromatography, and mass spectrometry, and emerging portable PAH detection technologies. By highlighting the limitations of existing systems and presenting novel sensing approaches, this paper aims to catalyze innovation in sensor development. Our ultimate goal is to inspire the creation of robust, field-deployable tools that enhance decontamination practices and significantly improve the health and safety of firefighters by reducing their long-term risks of cancer. Full article

Mercury (Hg) is a globally recognized toxic element, and the Minamata Convention on Mercury entered into force in 2017 to address its associated risks. Under the United Nations Environment Programme, international efforts to reduce Hg emissions and monitor its environmental presence are ongoing. In support of these initiatives, we developed a simple and rapid mercury detection device based on a quartz crystal microbalance (QCM-Hg sensor), which utilizes the direct amalgamation reaction between Hg and a gold (Au) electrode. The experimental results demonstrated a proportional relationship between Hg concentration and the resulting oscillation frequency shift. Increased flow rates and prolonged measurement durations enhanced detection sensitivity. The system achieved a detection limit of approximately 1 µg/m³, comparable to that of commercially available analyzers. Furthermore, a measurement configuration integrating the reduction-vaporization method with the QCM-Hg sensor enabled the detection of mercury in aqueous samples. Based on the experimental results and the gas-phase detection sensitivity achieved to date, concentrations as low as approximately 0.05 µg/L appear to be detectable. These findings highlight the potential of the QCM-Hg system for on-site mercury monitoring. This review aims to provide a comprehensive yet concise overview of QCM-Hg sensor development and its potential as a next-generation tool for environmental and occupational mercury monitoring. Full article

Benzene, a well-established human carcinogen and major industrial pollutant, poses significant health risks through occupational exposure due to its no-threshold effect, leading to multi-system damage involving the hematopoietic, nervous, and immune systems. This makes the investigation of its toxic mechanisms crucial for precise prevention and control of its health impacts. Programmed cell death (PCD), an orderly and regulated form of cellular demise controlled by specific intracellular genes in response to various stimuli, has emerged as a key pathway where dysfunction may underlie benzene-induced toxicity. This review systematically integrates evidence linking benzene toxicity to PCD dysregulation, revealing that benzene and its metabolites induce abnormal subtypes of PCD (apoptosis, autophagy, ferroptosis) in hematopoietic cells. This occurs through mechanisms including activation of Caspase pathways, regulation of long non-coding RNAs, and epigenetic modifications, with recent research highlighting the IRP1-DHODH-ALOX12 ferroptosis axis and oxidative stress–epigenetic interactions as pivotal. Additionally, this review describes a comprehensive monitoring system for early toxic effects comprising benzene exposure biomarkers (urinary t,t-muconic acid (t,t-MA), S-phenylmercapturic acid (S-PMA)), PCD-related molecules (Caspase-3, let-7e-5p, ACSL1), oxidative stress indicators (8-OHdG), and genetic damage markers (micronuclei, p14ARF methylation), with correlative analyses between PCD mechanisms and benzene toxicity elaborated to underscore their integrative roles in risk assessment. Furthermore, the review details analytical techniques for these biomarkers, including direct benzene detection methods—direct headspace gas chromatography with flame ionization detection (DHGC-FID), liquid chromatography-tandem mass spectrometry (LC-MS/MS), and portable headspace sampling (Portable HS)—alongside molecular imprinting and fluorescence probe technologies, as well as methodologies for toxic effect markers such as live-cell imaging, electrochemical techniques, methylation-specific PCR (MSP), and Western blotting, providing technical frameworks for mechanistic studies and translational applications. By synthesizing current evidence and mechanistic insights, this work offers novel perspectives on benzene toxicity through the PCD lens, identifies potential therapeutic targets associated with PCD dysregulation, and ultimately establishes a theoretical foundation for developing interventional strategies against benzene-induced toxicity while emphasizing the translational value of mechanistic research in occupational and environmental health. Full article

Air pollution and the emission of toxic gases represent a critical global concern, posing significant threats to human health and environmental stability. Resistive gas sensors are widely employed to detect toxic gases, owing to their cost-effectiveness, high stability, sensitivity, and swift dynamics. Among various sensing materials, comparatively less attention has been paid to CeO₂ despite its good catalytic activity and high stability. In this review paper, we are focusing on CeO₂ gas sensors in pristine, doped, decorated, and composite forms. Using numerous examples, we have shown the great potential of CeO₂ for gas sensing. The main features of CeO₂ as a gas sensor include excellent environmental stability, the abundance of oxygen vacancies, high mechanical strength, cost-effectiveness, and good catalytic activity. However, low electrical conductivity is the main shortage of CeO₂ as a gas sensor. With a high emphasis on the sensing mechanism, we believe that this review paper is highly useful for researchers working in this field. Full article

The soil phytomonitoring and phytostabilization potential of Syringa vulgaris and Ficus carica was evaluated regarding 16 priority polycyclic aromatic hydrocarbons (PAHs) using a chemometric approach and the calculation of bioconcentration factors (BCFs) for each individual PAH in plants’ roots from each selected location in the Bor region. PAHs in roots and the corresponding soils were analyzed using the QuEChERS (Quick, Effective, Cheap, Easy, Rugged, Safe) method with some new modifications, gas chromatography/mass spectrometry, Pearson’s correlation study, hierarchical cluster analysis, and BCFs. Several central conclusions are as follows: Each plant species developed its own specific capability for PAH management, and root concentrations ranged from not detected (for several compounds) to 5592 μg/kg (for fluorene in S. vulgaris). In some cases, especially regarding benzo(a)pyrene and chrysene, both plants had a similar tactic—the total avoidance of assimilation (probably due to their high toxicity). Both plants retained significant quantities of different PAHs in their roots (many calculated BCFs were higher than 1 or were even extremely high), which recommends them for PAH phytostabilization (especially fluorene, benzo(b)fluoranthene, and benzo(k)fluoranthene). In soil monitoring, neither of the plants are helpful because their roots do not reflect the actual situation found in soil. Finally, the analysis of the corresponding soils provided useful monitoring information. Full article

Efficient detection of toxic and flammable vapors remains a major technological challenge, especially for environmental and industrial applications. This paper reports on the fabrication technology and gas-sensing properties of nanostructured Ga₂O₃/GaS_0.98Se_0.02. The β-Ga₂O₃ nanowires/nanoribbons with inclusions of Ga₂S₃ and Ga₂Se₃ microcrystallites were obtained by thermal treatment of GaS_0.98Se_0.02 slabs in air enriched with water vapors. The microstructure, crystalline quality, and elemental composition of the obtained samples were investigated using electron microscopy, X-ray diffraction, and Raman spectroscopy. The obtained structures show promising results as active elements in gas sensor applications. Vapors of methanol (CH₃OH), ethanol (C₂H₅OH), and acetone (CH₃-CO-CH₃) were successfully detected using the nanostructured samples. The electrical signal for gas detection was enhanced under UV light irradiation. The saturation time of the sensor depends on the intensity of the UV radiation beam. Full article

Hydrogen sulfide (H₂S), once regarded solely as a highly toxic gas, is now recognized as a crucial signaling molecule in plants, bacteria, and mammals. In humans, H₂S signaling plays a role in numerous physiological and pathological processes, including vasodilation, neuromodulation, and cytoprotection. To exploit its biological functions and therapeutic potential, a wide range of H₂S-releasing compounds, known as H₂S donors, have been developed. These donors are designed to release H₂S under physiological conditions in a controlled manner. Among them, self-reporting H₂S donors are seen as a particularly innovative class, combining therapeutic delivery with real-time fluorescence-based detection. This dual functionality enables spatiotemporal monitoring of H₂S release in biological environments, eliminating the need for additional sensors or probes that could disrupt cellular homeostasis. This review summarizes recent advancements in self-reporting H₂S donor systems, organizing them based on their activation triggers, such as specific bioanalytes, enzymes, or external stimuli like light. The discussion covers their design strategies, performance in biological applications, and therapeutic potential. Key challenges are also highlighted, including the need for precise control of H₂S release kinetics, accurate signal quantification, and improved biocompatibility. With continued refinement, self-reporting H₂S donors offer great promise for creating multifunctional platforms that seamlessly integrate diagnostic imaging with therapeutic H₂S delivery. Full article

Copper is an essential micronutrient for plants, but excessive levels can induce toxicity and impair physiological functions. This study evaluates the toxic effects of copper sulfate (CuSO₄) on the germination of common wheat (Triticum aestivum), with emphasis on the gas emission dynamics and oxidative stress biomarkers. Seeds were germinated in agar and exposed to CuSO₄ at concentrations of 1 µM, 100 µM, 1 mM, and 10 mM; distilled water served as the control. Ethylene and ammonia emissions were quantified using CO₂ laser photoacoustic spectroscopy, while electron paramagnetic resonance (EPR) spectroscopy was employed to detect free radicals and Cu²⁺ complexes. Exposure to Cu concentrations ≥ 1 mM significantly inhibited germination and biomass accumulation. Enhanced ethylene and ammonia emissions, particularly at 10 mM, indicated stress-related metabolic responses. The EPR spectra confirmed the presence of semiquinone radicals and Cu²⁺ complexes under higher Cu levels. These results demonstrate that photoacoustic and EPR techniques are effective tools for the early detection of metal-induced phytotoxicity and offer a non-invasive approach to environmental toxicity screening and plant stress assessment. Full article

Ammonia, as a toxic and corrosive gas, is widely present in industrial emissions, agricultural activities, and disease biomarkers. Detecting ammonia is of vital importance to environmental safety and human health. Sensors based on MXene have become an effective means for detecting ammonia gas due to their unique hierarchical structure, adjustable surface chemical properties, and excellent electrical conductivity. This study reviews the latest progress in the use of MXene and its composites for the low-temperature detection of ammonia gas. The strategies for designing MXene composites, including heterojunction engineering, surface functionalization, and active sites, are introduced, and their roles in improving sensing performance are clarified. These methods have significantly improved the ability to detect ammonia, offering high selectivity, rapid responses, and ultra-low detection limits within the low-temperature range. Successful applications in fields such as industrial safety, food quality monitoring, medical diagnosis, and agricultural management have demonstrated the multi-functionality of this technology in complex scenarios. The challenges related to the material’s oxidation resistance, humidity interference, and cross-sensitivity are also discussed. This study aims to briefly describe the reasonable design based on MXene sensors, aiming to achieve real-time and energy-saving environmental and health monitoring networks in the future. Full article