1. Introduction
With the development of railway construction in China, the proportion of bridges in railway lines has gradually increased. When a vehicle passes through the bridge, the wheel–rail force is transmitted to the bridge through the track structure, which causes strain and deformation of the bridge, consequently affecting the safety and comfort of the track structure on the bridge. Cheng et al. proposed a bridge–track–vehicle unit model to study the interaction among the mobile vehicle, track structure, and bridge. The results show that the bridge has a great influence on the dynamic response of track structure [
1]. Lou et al. found that the effects of track structure on vertical displacement and vertical acceleration of the car body are significant [
2]. Xiao et al. demonstrated that the effects of the track on the lateral responses of vehicle and bridge cannot be ignored and the reasonable and comprehensive analysis of vehicle–track–bridge interaction should consider the effects of the track [
3]. In summary, the selection of track structure on a railway bridge is of considerable importance. At present, the ballasted track, slab ballastless track, and wooden sleeper (composite sleeper) track on the open deck are the main track forms used on bridges.
The ballasted track is a common track form on the steel bridge deck. It has the characteristics of low engineering cost and strong adjustment ability. However, the use of a ballasted track will increase the height of the track structure and the secondary dead load of the bridge. In addition, under the repeated load of the vehicle, the deformation of the ballast bed will accumulate. In severe cases, the ballast will be broken and powdered. Therefore, it is very important to study the mechanical properties and identify the ballast. Podwmna et al. analyzed the random vibration characteristics of the vehicle–track–bridge coupling model under different vehicle speeds, and proposed a problem of possible destabilization of macadam ballastbeds on railway bridges. One possible solution is applying the ballastless track structure [
4,
5,
6]. By comparing the results from the cyclic loading test on the ballast using a large-scale triaxial test apparatus with the full-scale laboratory test in the railway test facility (RTF), Aursudkij et al. analyzed the permanent axial strains and particle size distribution under traffic loading [
7]. Moaveni et al. used an image analysis approach based on machine vision algorithms to assess ballast condition and degradation levels [
8]. However, due to the structural characteristics of the ballasted track on the bridge, it is difficult to inspect the bridge deck and maintain the ballast bed. Consequently, this will lead to an increase in maintenance workload.
Different from the ballasted track, the slab ballastless track can reduce the secondary dead load of the bridge and the maintenance workload. In the meantime, the mechanical characteristics of ballastless tracks will also be affected by the behaviors of bridges. Ruge et al. studied the interaction between the track and bridge under the action of vehicle loading and seasonal temperature change and proposed that stresses in track structure on bridges are strongly influenced by the coupling interface between track and bridge in the longitudinal direction [
9]. Full-scale fatigue tests and post-fatigue loading tests were carried out by Sheng et al. to research the mechanical behaviors and fatigue performances of ballastless tracks laid on long-span cable-stayed bridges [
10]. The results indicate that ballastless track on bridge has good performance in fatigue property. In the work of Zheng et al., a segmental model was developed in the laboratory, on which various types of ballastless tracks were paved [
11]. The authors suggested that appropriate track type can improve the mechanical performance of the structure. Previous research has established that the slab ballastless track can improve track regularity and stability. However, some scholars proposed that it is prone to crack under the influence of temperature and bridge deformation, which affects the durability of the structure [
12,
13,
14].
Compared with the traditional ballasted track and ballastless track, the sleeper track on the open deck has a simpler structure with a smaller secondary dead load. Wooden sleepers are the main track structure used on the open deck of steel truss bridges. However, wooden sleepers have poor durability and can easily decay and crack. Scholars from all over the world began to look for new materials to replace wooden sleepers [
15,
16]. In the work of Cantero et al., the mechanical properties of composite sleepers and wooden sleepers were compared and analyzed by the finite element method. The research showed that the performance of composite sleepers is equivalent to that of wooden sleepers, and only one-third of the volume of standard wooden sleepers is needed [
17]. Manalo et al. used the four-point static bending test on composite sleepers to study the strength and failure mechanisms [
18]. Data from the above research suggest that composite sleepers have good performance in flexural behavior. Ferdous et al. proposed to coat epoxy-based polymer concrete on the sleeper surface to protect the sleeper from unfavorable environments and increase the strength of the rail-seat area [
19]. After summarizing the material properties of various composite sleepers, Ferdous et al. pointed out the problems existing in the application and development of composite sleepers [
20,
21]. The primary obstacles to the composite sleepers are their prohibitive cost, low anchorage capability of holding screws, formation of voids in the body of the sleeper, permanent deformation due to creep and temperature variations, and insufficient lateral resistance.
Nansha Port Railway in Guangzhou is a mixed passenger and freight railway with a design speed of 120 km/h. It has a through bridge with a steel truss and arch. The total length of the bridge is 996 m. In order to prolong the maintenance period of the track structure and reduce the secondary dead load of the bridge, a new type of concrete sleeper slab track structure on the open deck was adopted. The integrity of the structure was improved by prefabricating two sleepers into one and setting up vertical and horizontal limit devices. The adjusting cushion, sleeper slab, and cushion under the slab were set up between the sleeper slab and the steel beam. High strength bolts were used to connect the structure vertically, as shown in
Figure 1. In practical engineering, the train operation produces a large vertical force and when the train passes through the curve section or has a hunting motion, it produces a large transverse force. Furthermore, the train operation, breaking, and passing through the ramp also produces a large longitudinal force. The coupling effect of the three-dimensional force has a great impact on the track structure and even damages it [
22,
23]. In order to study the mechanical properties and long-term performance of the new type of sleeper slab track structure, this paper carried out a full-scale indoor modal loading test of the concrete sleeper slab track structure to provide a reference for the engineering application.
2. Specimen Geometry and Materials
The indoor full-scale sleeper slab track structure consists of a rail, fastening system, sleeper slab, self-compacting concrete cushion, and flange slabs of steel truss bridge (simulated by two steel beams), as shown in
Figure 2. The sleeper slab and the self-compacting concrete are made of C60 and C40 concrete, respectively. The concrete specimens were cured under the same conditions and the dimensions are 150 mm × 150 mm × 150 mm. After 28 days, the cube compressive strengths measured by the prefabrication plant are 70.1 and 48.4 MPa. The steel beams are elastically supported within a certain range (the support spacing is 1.6 m) in order to simulate the vertical deformation of the steel truss bridge and the support form of the track structure in practical engineering.
In the test, the dimensions of the sleeper slab are 1200 mm (length) × 2720 mm (width) × 240 mm (height) and each sleeper slab is made of double sleepers with a spacing of 625 mm between them. The dimensions of the self-compacting concrete cushion are 1150 mm (length) × 580 mm (width) × 120 mm (height), and each sleeper slab track structure has two symmetrical cushions. Moreover, the 60 kg/m rail is used in this structure, and the density is 7850 kg/m3.
3. Test Content
The test contents carried out in this paper include the vertical static load test, the vertical fatigue test, and horizontal resistance test of the sleeper slab. A PMS-500 digital display pulsing machine was used for vertical static load and sine cyclic load. A distribution beam was set on the middle of the track structure to simulate vehicle uniaxial load. The static load was 625 kN, which is 2.5 times the equivalent wheel load (250 kN) [
24]. In the vertical static load test, the displacement and strain were measured by sensors to study the bearing capacity and force characteristics of the track structure. The transverse and longitudinal static loads on the sleeper slab were applied using a jack. In the test, the longitudinal and transverse forces adopted were F1 = 36 kN and F2 = 100 kN, respectively. The resistance of the horizontal limit device of the sleeper slab was studied by measuring the displacement of the sleeper slab relative to the steel beam. In the vertical fatigue test, the maximum load applied was 375 kN, which is 1.5 times the equivalent wheel load (250 kN), while the minimum load was 75 kN, which is 10% of the maximum load [
14,
25]. The train load conformed to the normal distribution; therefore, the cyclic load was set up as a sine form with 5 Hz and a total of 3 × 10
6 cycles. In addition, the vertical static load test and horizontal resistance test were carried out after every 10
6 cycles to study the bearing capacity and durability of the sleeper slab track. The above tests are of great value to understand the mechanical properties of the new track structure.
3.1. Arrangements of Strain Gauges
When the track structure bears the train load, the concrete strain at the edge is the most unfavorable. Therefore, the strain state of the concrete at the edge is studied emphatically in this paper. To avoid the damage of concrete strain gauges, the surfaces of the strain gauges were protected with structural glue. There were a total of 12 measuring points on the structure. Among them, the sleeper slab and the self-compacting concrete cushion had six measuring points, respectively. The arrangements of the measuring points are shown in
Figure 3.
On the sleeper slab, 1, 2, 5, and 6 are the angle crack measuring points of the sleeper slab. Points 3 and 4 are the middle measuring points of the sleeper slab.
On the self-compacting concrete cushion, 7 and 10 are the middle measuring points of the short side; 8 and 11 are the end measuring points of the right long side; and 9 and 12 are the middle measuring points of the right long side. The measuring points of the self-compacting concrete cushion are at the middle height of the sides.
3.2. Arrangements of Displacement Sensors
3.2.1. Vertical Displacement of Static Load Test
A total of 15 vertical displacement sensors were arranged on the structure. The arrangements were as follows: two rail displacement sensors were used to measure the rail displacement relative to the sleeper slab; eight sleeper displacement sensors were used to measure the sleeper slab displacement relative to the steel beam; and five steel beam displacement sensors were used to measure the displacement of the steel beam fulcrum, middle position, and quarter position. The arrangements of the measuring points are shown in
Figure 4.
3.2.2. Horizontal Displacement of Resistance Test
In the horizontal resistance test, a total of eight horizontal displacement sensors were arranged on the structure. This included four longitudinal displacement sensors and four transverse displacement sensors. These sensors were used to measure the displacement of the sleeper slab relative to the steel beam in the horizontal direction. The arrangements of the measuring points are shown in
Figure 5, and the loading devices used in the horizontal resistance test are shown in
Figure 6.
5. Conclusions
In the present paper, full-scale laboratory tests on the sleeper slab track structure were proposed, consisting of the vertical static load test, vertical fatigue test, and horizontal resistance test. From the test results, the mechanical characteristics and fatigue behavior of the sleeper slab track were evaluated. The conclusions of this research are as follows.
These experiments confirmed that after 3 million cycles of sine cyclic loading, the sleeper slab track is considered to maintain excellent mechanical properties. As the number of loading cycles increased, the strain of the sleeper slab and self-compacting cushion varied slowly. The unfavorable positions were found in the inner side of the sleeper, the mid-span of the slab, and the middle of the short side of the cushion. Compared with the strain, the change in vertical displacement was considered to be more obvious due to the stiffness change under the action of cyclic loading.
The results of the transverse ultimate resistance test indicate that failure occurred in the track structure when the transverse force reached 413.4 kN. The main failure modes were separation between the self-compacting concrete cushion and steel beam, crack between the sleeper slab and cushion, and deformation of the iron plate at the bolt position. In addition, the longitudinal resistance test also showed that the track structure can still bear a longitudinal force of up to 100 kN after transverse failure.
The new type of track structure proposed in this paper is planned to be applied to the long-span steel truss bridge to overcome the weaknesses of the traditional track structure on the open deck, such as poor integrity, difficult sustenance of track geometry, and heavy maintenance work. The main purposes of the current study were to verify the applicability of the sleeper slab track on the long-span steel truss bridge and to investigate the mechanical characteristics during the fatigue process with an experimental method. In order to investigate the performance parameters of the track structure more comprehensively, future work to be performed by the authors will be focused on the precise numerical simulation of the track structure.