1. Introduction
Electric vehicles (EVs) are becoming more popular with time. Based on Reference [
1], this type of vehicle is driven by at least one non-peripheral electric motor, which draws its energy mainly from an electric rechargeable energy storage system (battery pack). This storage system is recharged mostly by using an external energy supply system [
1]. EVs date from the early days of transportation and comparing with conventional gasoline and diesel vehicles, they present by far a higher energy efficiency ratio [
2]. In general, EVs are divided into three main categories; battery (BEVs), hybrid (HEVs) and fuel cell electric vehicles (FCEVs) [
1].
EVs accelerate fast, achieving speeds almost comparable to those of conventional vehicles [
2]. Additionally, they are environmentally friendly, because they produce zero direct emissions. This fact contributes to the reduction of air and carbon pollution from the transportation sector, which is a strong advantage of EVs against conventional vehicles. Other advantages of EVs are the low maintenance costs, due to their simple mechanical structure, the promotion of new technologies, such as Vehicle to Grid (V2G) operation, and their suitability in urban centers [
1]. On the other hand, conventional vehicles can achieve higher speeds and longer distances compared to EVs, while, because of their silent electric motors and frequent use in urban centers, EVs are not easily perceived by pedestrians [
1,
2].
A basic system of EVs is the high voltage circuit, where the basic parts of the vehicle’s equipment are connected together by bright orange high voltage wires [
3]. According to Reference [
3], the circuit is closed by high voltage service disconnects, which are located in the rear part of the EV and consist of thermal sensors and control units, in order to monitor their operation. The voltage in the circuit starts from 48 Volts DC (VDC); in normal conditions, it can reach the maximum voltage that the battery pack can handle under normal conditions (about 600 VDC), and in danger exceeds 800 VDC [
3,
4].
Other features of a typical EV include a 12 Volt battery, which is needed for the operation of the vehicle’s electronics, badges indicating that the vehicle is electric, and the absence of an exhaust [
3,
5]. In addition, there are safety systems in the car; the Electronic Stability Program (ESP program) is an active safety system that provides two other active safety systems: an anti-lock braking (ABS) system, which prevents the wheels from locking during braking, and a traction control system (TCS), which prevents the wheels from spinning when the vehicle starts off and accelerates [
6]. Additionally, other parts include a set of airbags (six to seven in a typical European electric car) and seatbelt pretensioners, a vehicle collision detection system, a control unit for the air conditioning and heating systems, the dashboard of the car, and a set of electrical and electronic components [
3,
5].
A typical BEV consists of a propulsion system and a battery-charging facility, which are connected by a high-voltage circuit. The propulsion system includes an electric motor, a battery pack, converters located next to both of them, and buck-boost choppers [
1,
7]. An electric car powertrain is depicted in the figure below (
Figure 1) [
8].
The electric motors that are used in EVs include brushed direct current (DC) motors, induction motors, synchronous reluctance motors, and permanent magnet synchronous and brushless DC motors [
1]. The most commonly used battery packs in BEVs and HEVs are nickel-metal hydride (NiMH), lithium-Ion (Li-Ion) and lithium-polymer (LiPolymer) batteries [
1]. The battery charging facility, which can be used either at home or at public charging stations in order to charge the EV, allows either on-board or off-board charging, or both [
9].
Apart from pure electric cars, hybrid electric cars represent another major vehicle category. Hybrid electric vehicles include an internal combustion engine (ICE) connected with an electric motor or generator (in some vehicles), buck-boost converters and a battery pack. The fuel, usually diesel, is stored in a tank that is highly resistant to high pressures, temperatures and corrosion [
10]. There are also valves and quantity and pressure sensors, in order to control the pressure and the flow of the fuel into the transfer pumps [
10]. This type of vehicle is more efficient for long-distance trips and develops higher speeds than a BEV, but should be maintained more often, due to its complexity. Respectively, the maximum developed voltage in hybrid electric vehicles is around 650 VDC [
10].
EVs with hydrogen fuel cells are another category. This type of car uses hydrogen as fuel for its operation. This kind of fuel is stored in a tank usually made of carbon fiber. Inside the tank, the fuel pressure for optimal and safe operation must be 700 bar (70 MPa) [
11], while the fuel temperature fluctuates between −40 °C and 85 °C [
12]. The maximum pressure of the fuel that the tank can carry is 172 MPa at a minimum [
13]. A pumping system is used in order to help the hydrogen flow from the tank to the fuel cells [
14], while excessive flow and any hydrogen leakage are detected by sensors, most of them located near the cabin [
13]. In FCEVs, the maximum developed voltage is around 500 VDC in some vehicles. Exceeding the voltage can cause short circuits, which lead to extensive vehicle equipment damage and total explosion of the car [
15].
A modern, quite popular driving ability is autonomous driving. According to Reference [
16], autonomous driving is a driving ability where the vehicle has the ability to sense its surroundings and move within defined lanes without human interaction. Based on References [
16,
17], autonomous cars use sensors, a lidar system, camera and mapping applications, in order to map around their routing area and for moving. Taeihagh and Min Lim [
17] note that the frequent use and extensive popularity of autonomous cars raise various problems, such as faults in their equipment, cybersecurity issues and even malicious use (such as kidnapping phenomena), leading to serious traffic accidents. In order to address them and make the use of self-driving cars safer, new technologies will need to be proposed.
In recent years, EVs have been gaining ground in the global transportation market. According to the global EV outlook for 2022 [
18], nearly 10% of global car sales were for electric vehicles in 2021, whereas 16.5 million electric cars were on the road. In the first quarter of 2022, 2 million electric cars were sold, 75% more than in the same period in 2021. The number of public chargers is increasing continuously, in order to reach over 15 million units by 2030. China and the United States are the two countries with the largest number of electric vehicles in circulation on the planet. In the coming years, the number of electric vehicles plying the roads worldwide will increase such that, by 2030, the total global electric vehicle stock may reach almost 145 million vehicles, and annual sales may exceed 25 million (reaching almost 15 million cars in 2025) [
19].
Taking into consideration, on one hand, the occurrence of serious accidents in the last 12 years (2010–2022) involving such vehicles (electric, hybrid electric, hydrogen fuel cell and self-driving), and on the other hand, the progress in the development of the aforementioned vehicle equipment over time with regard to safety issues, the goal of this is to propose additional technological innovations, applications or materials for use in the near future.
Table 1 lists some of the electric car road accidents that occurred in the last 12 years (2010–2022)—which led to extensive fires—and the manner of response [
20,
21,
22,
23,
24,
25,
26,
27,
28,
29,
30,
31].
The paper is structured as follows. First, some introductory facts are presented regarding electric propulsion, existing technologies and the evolution of electric car use in the coming years. Then, a study of the risks and safety systems, associated with the usage of EVs, is conducted, with the need for equipment development emphasized. In addition, the evolution of the equipment used in electric and hybrid electric vehicles, hydrogen fuel cell vehicles, and self-driving cars as well as of the charging devices over time and in the near future are presented. Further, an assessment of electromagnetic interference mitigation equipment is also made. So, considering all of the above, the paper discusses additional technological innovations and applications related to the evolving equipment, with hints and tips for better operation of the equipment in the near future and proposals for new materials, all with the aim of facilitating better equipment function and safer vehicle operation. The final section of the paper summarizes the topics discussed and presents its conclusions, and is followed by bibliographic references.
2. Dangers Associated with Electric Cars and Safety
This chapter focuses on the dangers of EV use and the safety systems the vehicle has. Dangers and road accidents form the basis for electric car equipment development. The equipment is evolving, in order to help make the roads used by these vehicles safer, and to reduce the number of accidents as the years pass.
The increased use of electric vehicles poses dangers. Looking at EV incidents that have occurred in recent years, the risks arising from EVs can be generally categorized into major incident factors such as general EV damage, human factors, high-voltage circuit malfunctions, wear and tear of equipment, weathering, environmental effects and other risks related with EV system functions and faults in hybrid electric vehicle or hydrogen propulsion equipment [
32]. Road accidents and vehicle submersion can cause extensive fires, serious toxicity (due to gas emissions and spill hazards) and electrical hazards, such as extensive short circuits, the development of electric arcs and discharges [
5].
Generally, considering the accidents referred to in
Table 1 [
20,
21,
22,
23,
24,
25,
26,
27,
28,
29,
30,
31], it seems that most accidents were caused either by general vehicle damage, due to excessive use, internal faults, or serious faults during charging, or by collisions with other vehicles or objects due to high speed, whereas accidents involving vehicle submersion in water or rollovers were less frequent. In all accidents, a fire was caused—either controlled or catastrophic—in some cases, there were human casualties, and there was a serious electrical risk.
Electric cars are equipped with various safety systems. Beyond the active and passive safety systems that were mentioned in the introduction, the cars are equipped with systems that ensure safety during use, such as an automatic shut-down system, adaptive cruise control system (ACC), blind spot and forward collision warning system, active brake assist, lane assist system, crash avoidance technology to prevent possible crashes, wrong-way driver warning systems and pedestrian and cyclist warning systems. In the future, all of these systems will be improved, whereas new technologies and trends such as lidars and cameras in electric cars, more flexible electric drive actuators, improved protection systems, advanced communication V2I models and improved battery management systems with data recording technology will be introduced [
33,
34,
35,
36].
Considering the accidents that have occurred and the increasing use of electric vehicles, electric car equipment designs will evolve. Based on the accidents and the advances in these vehicles’ designs, in the future their equipment will be constructed in such a way as to withstand greater current and voltage than the present equipment and have the ability to deal with any faults that may occur, thus preventing and leading to fewer accidents than at present. In the end, additional technological innovations and applications can be proposed in order to increase safety.
4. Advances in Hybrid Electric Vehicles’ Equipment
As mentioned in the introduction, hybrid electric vehicles have quite complex equipment that requires continuous maintenance. According to References [
167,
168], the common equipment for electric cars consists of an internal combustion engine (ICE) in combination with an electric motor, an electric generator (in some vehicles) connected to the ICE, buck-boost converters, a high-capacity battery pack (mainly Li-Ion and NiMH) with high energy density cells and fuel tank. The electric motor drives the front axle of the vehicle through an automatic mechanical transmission (AMT) system [
160]. Various configurations that exist in hybrid electric vehicles are: series HEV, parallel HEV, series-parallel HEV or complex HEV configurations [
169]. There are also valves and quantity and pressure sensors that control the pressure and the flow of the fuel into the transfer pumps [
10]. The cooling of the hybrid electric car system is conducted by a system of radial coolant pumps, assisted by the car’s air conditioning system [
170]. In addition, the equipment also includes supercapacitors and flywheels that store electrical and kinetic energy (hybrid energy storage with supercapacitors), supplying the car with extra energy besides that from the battery packs [
169]. According to Reference [
171], a speed controller and velocity advisory system control the vehicle’s movement. In hybrid electric cars, also according to Reference [
171], there is a system that monitors the traffic on the road near the vehicle using the Global Positioning System (GPS), radar or Geographic Information System (GIS), which, in conjunction with the vehicle speed controller, helps the vehicle achieve better fuel management and movement. The structural diagram of a plug-in hybrid electric vehicle, based on Reference [
167], is depicted in
Figure 8.
Over the years, the equipment has been upgraded and changed, in the sense that the electric motor power has been increased from 10 kW in the 1990s to above 120 kW nowadays. The equipment has been improved and now integrates supercapacitors and traffic and navigation systems [
172]. Based on Reference [
173], dedicated hybrid transmission systems will appear in the future, where, according to Reference [
174], the equipment will evolve in such a way that motor operation and driving efficiency will be improved, and ICE engines will be more efficient. According to [
174], hybrid electric vehicles will have greater range with one charge or fuel filling and emit fewer pollutants (mainly from ICE, such as nitrogen oxides (NO
X), carbon monoxide (CO), carbon dioxide (CO
2) and hydrocarbons). Of course, there will be several losses—mainly torque and high energy conversion losses. To achieve these gains, the electric motors will take up less space; the equipment, due to its complexity, may be connected with piezoelectric energy harvester systems (such as piezoelectric materials), which may be installed in the hybrid electric vehicle and mounted in locations such as suspension springs, dampers and tires, in order to reduce vibrations. Models of a piezoelectric material are depicted in the figure below (
Figure 9) [
175]. The harvesters will feed the battery pack with extra clean electric energy simultaneously [
175]. Apart from the conventional way of charging, battery packs of the future will be charged wirelessly.
Besides piezoelectric harvester systems, hybrid electric vehicle equipment may include materials that reduce vibrations, such as more clutches [
173] and buffers of different thicknesses [
176]. Even the improved powertrain will help to mitigate possible vibrations. For reduced electromagnetic interference and better operation, several passive EMI filters will be applied.
Of course, for greater fuel savings, EVs may integrate complex systems with multiple parallel-axis gears, planetary gear sets and shifts [
173]. For the purposes of loss reduction, the equipment in hybrid electric cars may be made from ceramic or polymeric materials, with ceramic protective coatings [
177]; also, tanks or pumps may be made from nanomaterials or carbon fibers, with improved coating thicknesses [
178]. The transmissions may be lubricated with lower viscosity oils for better performance [
178], or incorporate improved lubrication systems [
174].
5. Advances in Hydrogen Fuel Cell Equipment
In addition to electrically chargeable vehicles, EVs with hydrogen fuel cells comprise another major category of EVs. They use hydrogen as fuel for their operation [
1]. As noted in the introduction, this kind of fuel is stored in a tank (or tanks) usually made of carbon fibers [
179] and reinforced plastic [
180]. According to the current (SAE J2579) and National Highway Traffic Safety Association (NHTSA) regulations [
180,
181], the already existing tanks (storing compressed hydrogen), have an isolation valve (each with one of them), flow control systems, valves for high and low pressure, supply shutdown and pressure-relief valves that can release hydrogen, thus reducing the pressure in the tank. It takes five minutes to empty a hydrogen tank.
A pumping system is used to transfer the required hydrogen from the tank to the fuel cells. In the event of a hydrogen concentration increase, the supply of hydrogen from the tank to the cells and pumps stops, and the fuel cells deactivate, so the electric motor is not supplied with electricity, and the hydrogen car is then driven by the battery pack. Inverters are located near the pumps and regulate their operation [
180]. The hydrogen level, as well as temperature and pressure, are measured by using up to four sensors, most of them located near the cabin and also able to detect any possible leakage [
180]. In addition, according to this NHTSA report [
180], an air compressor supplies oxygen to the fuel cell pack. Additionally, a fuel cell air-cooling system uses a fan and a cooling pump to cool the electrical components and the high-voltage circuit, thus maintaining the system at normal operating temperatures and preventing hydrogen from igniting [
180].
Finally, the system is equipped an overcurrent protection circuit, which includes fuses, and a ground fault detection circuit (ground fault monitoring system) [
182]. In an FCEV's high-voltage circuit, the maximum developed voltage is around 500 volts DC. In a nutshell, the components of a well insulated and grounded fuel cell system, based on References [
183,
184,
185], are:
Thermal/Cooling system (water cooling system);
DC/DC converter or multi-device interleaved boost converters;
AC electric motor;
Fuel cell stack (commonly proton-exchange membrane fuel cell (PEMFC));
Battery pack (commonly Li-ion/LiPolymer/NiMH);
Fuel filler;
Carbon-fiber fuel tank with safety valves (the fuel that is stored in the tank is hydrogen);
Pumping system;
Hydrogen level measuring, temperature and pressure sensors (up to four sensors in the vehicle);
Transmission system;
Power electronic controller;
Secondary and auxiliary battery;
Supercapacitors and flywheels;
PI Controllers and inverters for control.
Some hydrogen fuel cell electric vehicles are listed in the following table (
Table 5).
Looking at the above table (
Table 5) listing of hydrogen fuel cell electric vehicles, it appears that the fuel cell output power has increased over time (from over 60 kW in 2000 to over 100 kW currently), as well as the hydrogen tank operating pressure (surpassing 70 MPa in some cars since the 2000s) [
186,
187,
188,
189,
190,
191,
192,
193,
194,
195,
196,
197,
198,
199]. Additionally, the driving range and the operating voltage have increased. In the coming years, hydrogen cars will become just as competitive as common ICE vehicles. According to the NHTSA [
180], the vehicles of the future, will have greater driving range on one charge (over 400 miles), without evaporation losses, and less weight than present; the battery will charge in less time than now and will have an increased lifespan (over 5000 h). The equipment will consist of upgraded tanks and pumps and an upgraded temperature and pressure monitoring system, in order to withstand high temperatures (operating higher than 300
οC) and the risk of flammability, brittleness and fragility. The upgraded tanks may be made of either polymer- or metal-carbon nanotubes, metal hydrides or glass-fiber, in order to have the maximum energy density and to withstand greater hydrogen pressure [
200,
201]. Activated carbon will be used in improved fuel cells, which may consist of improved proton-conducting Nafion or thin ionizing membranes that prevent hydrogen gas from crossing, for greater strength and performance [
201]. According to Reference [
202], equipment in the future may contain carbon nanotube-type catalysts for increased useful power.
8. Advances in Autonomous Vehicles
As mentioned in the introduction, autonomous driving is quite popular and among the most researched automotive driving abilities. According to Reference [
222], the self-driving cars combine a variety of systems to perceive their surroundings, such as radar, lidar systems, GPS, driving assistance cameras and autopilot, as well as sensors to detect possible faults. The typical architecture of a self-driving car is structured by various systems and subsystems; they are referred below [
223].
the Perception System, which is responsible for estimating the state of the car and for creating a representation of the environment, using data captured by on-board sensors, such as lidar, radar, camera, GPS, odometry etc.;
the Decision-Making System is responsible for navigating the car from its initial position to the final position defined by the user;
the Localizer subsystem receives as input the offline maps, sensor data and the odometry of the self-driving car, and computes as output the car’s state;
the Moving Objects Tracker subsystem receives the offline maps and the self-driving car’s state and detects and tracks, and is responsible for detecting and tracking the pose of moving obstacles in the environment around the self-driving car;
the Traffic Signalization Detector subsystem, or TSD, is responsible for the detection and recognition of traffic signalization. It receives the sensors’ data and the car’s state, and detects the position of traffic signals and recognizes their class or status;
the Route Planner subsystem is responsible for computing a route;
the Motion Planner subsystem is responsible for computing a trajectory, whereas these trajectories are used by sensors in order to detect and avoid obstacles;
other subsystems are the Path Planner to plan a route, the Behavior Selector for choosing the correct driving behavior that the driver should consider, the Obstacle Avoider to avoid obstacles and collisions and Control Systems to control the vehicle.
For localization, the systems use one or more offline maps, such as occupancy grid maps, remission maps or landmark maps [
223]. Advanced control systems interpret sensory information in order to identify appropriate navigation paths, real-time location as well as obstacles, passengers or cyclists, in order to keep the car safe distances from pedestrians and somewhat reduce the risk of a traffic accident [
224].
Pedestrians and cyclists are alerted by relative sounds from the car. The self-driving cars also have a cybersecurity management system to alert the driver and the occupants to malicious activity and possible kidnappings and protect them from these activities [
224,
225]. Based on regulations and reports on self-driving cars [
223,
225,
226,
227], for the function of basic systems and subsystems in automated vehicles, the following technical specifications exist, as listed below:
Systems for the replacement of driver control of the vehicle;
Systems and event loggers that provide real time information on the condition of the vehicle and the surrounding area where the vehicle is moving and also on any failure, based on the state of the car provided by the Perception System;
Driver availability and behavior monitoring systems for activation of the Behavior Selector, in order to choose the correct behavior for the driver;
Driver assistance systems such as speed control, lane keeping assist, lane change, blind spot alert, and automatic braking; they are activated based on results from the Behavior Selector and Obstacle Avoider;
Communication systems (V2V long- or short-range communication modules (infrared, Li-Fi) and V2X communication systems) and systems providing safety information to other road users; they are used in order to alert pedestrians and cyclists.
The driver can interfere with the autonomous driving system and drive the vehicle manually in some situations. In that situation, to avoid accidents, the driver must obey the traffic code and be aware of dangers or faults from the car itself [
224]. Therefore, the car is equipped with a driver assistance system that monitors the driver’s vigilance and behavior during driving, so that the car will not stray from the road, and helps drivers stay focused while driving [
226]. There are applications for mobile phones that show static visual warnings, as part of road hazard warnings to the driver, or that use satellite navigation, in order to assist with the vehicle’s routing and parking [
228]. Finally, the cars typically have a software application that detects blind spots during car movement [
226].
The following table (
Table 6) illustrates the evolution of autonomous vehicle equipment over time, based on References [
229,
230]. Over the years, the technology has evolved to the point that it can benefit more people, i.e., it can transport more people, even the elderly and the disabled. In the future, autonomous vehicles will be an indispensable part of modern transport systems [
231]. Current technologies will be used in electric cars and self-driving cars extensively in the future, as well as systems that optimize acceleration and braking actions [
232], pilot assist systems for pedestrian identification [
233], and autodrive [
234]; also, new trends in car communication will appear, such as 5G (fifth generation of mobile communications) technologies and developed Wi-Fi and Bluetooth systems [
235]. The equipment will contain advanced systems (e.g., navigation system [
232], autopilot [
232], lidar [
232], radar with better resolution in all measurement dimensions [
236], more precise inertial sensors [
237], improved actuators [
223], cameras that deal with bad lighting conditions better than today [
237] and detect 3D objects immediately [
238], cybersecurity management systems [
232], and driving assistance systems) [
232]. In order to avoid the malicious use of self-driving cars in the future, the operating software and the navigation system will be updated, and the equipment will contain prerecorded maps to perform map-aided localization [
237] and improved antivirus and fault detecting software for prevention of cybersecurity issues [
224,
225]. Indeed, there will be a built-in locking system that will prohibit drivers from using the cars unless their systems are updated [
239].
Despite these developments, collisions can still be expected to occur during self-driving car operations in the future, but not as frequently as nowadays. Autonomous vehicles should be able to return to a safe condition immediately after being involved in an accident. In the event of a collision, according to regulations [
240], the self-driving car should stop, remove motive power, and notify the manufacturer, collision notification center and rescue crews with the data recorded in the black box or through the self-driving car’s communication system, if should anyone need help; otherwise, alerts will be sent through the car’s GPS. The automatic response system will unlock the doors and turn on the emergency lights. The battery pack should be disconnected, disengaging electric power. Consideration should be given to shutting off the fuel pump, if the car is a hybrid, and to transporting the vehicle to a safe off-road location.
9. Future Technologies and Materials
First, the equipment in an electric vehicle is very important for its operation. Proper operation of the equipment can help with any problems that may arise. With time, the charging equipment in electric vehicles will evolve in order to generate higher voltages and currents, thus leading to more electromagnetic interference than now, and the vehicles will have improved driving ranges. The current equipment, as it evolves in the future, will still not be adequate for the safe use of electric vehicles. So, additional technologies, applications or operating systems can be proposed.
For this reason, considering the increasing use of electric vehicles, the increases in their voltage, current and autonomy over the years, the charging equipment in current vehicles and and how it may change in the years ahead, additional technological innovations, applications, materials, proposals, suggestions and tips will be welcome going forward, to improve the operation of these vehicles and make driving electric cars easier and safer.
As for the battery packs, based on Reference [
241], an additional cooling system, with flame retardants, cooling pipes or heat exchangers, has been proposed to help maintain engine temperature at normal levels and prevent the engine from overheating. Suggestions were made in References [
241,
242] for insulation materials to be constructed of paraffin wax or thermoplastic elastomers (carbonate-esters, such as ester-b-carbonate-b-ester, as composite phase-change materials) for better strength, elasticity and long-term temperature management. Additionally, in Reference [
175], more dampers (damper bars) or piezoelectric materials, applied to mechanical parts and connecting to the battery pack, were suggested as ways to mitigate possible vibrations in electric motors and in batteries, and feed the battery with extra clean electric energy. For better absorption of vibrations and enhancements in thermal conductivity, it was suggested that battery pack protective membranes have a porous form [
243].
In Ref. [
1], it was suggested that manufacturers install an insulation resistance monitoring system to monitor and regulate insulation resistance, because the equipment must be well insulated, and that LCs or inductor-inductor-capacitor (LLC) resonant converters and decompression systems be integrated into the batteries. According to References [
244] and [
245], graphene-based organic batteries, due to their easy chemical manipulation, low cost, smaller size, higher energy density and greater autonomy, avoidance of heat sinks and increased safety and longer lifespan, were recommended along with lithium-glass batteries for greater resistance and autonomy (with up to 20,000 charging cycles).
For the charging procedure, due to the fact that voltage spikes and imbalances will still exist, as there will be more vehicles connected to the grid, References [
81,
246] recommend the future and widespread use of applications in mobile phones or tablets that, while the vehicle is connected to the charging facility, will monitor the charging operation for the presence of any faults (such as possible overvoltages or overcurrents), show voltage, current and charging time adjusted to the charging operation, and notify drivers of any faults so that the vehicle can be disconnected from charging facility in time. Besides protecting fuses or LC filters, improved SiC power modules also can be used to mitigate overvoltages [
247]. Applications that can monitor the availability of a charging station are also suggested; if a charging station or parking lot is full of charging cars, the applications should indicate the next-nearest charging station where the driver may charge their car. Drivers should consult the pertinent electric utility company to learn whether there is a load peak condition in the network and thus decide whether to charge their car or not. In conclusion, based on reference [
81], it is recommended that electricity distribution operators (DSOs) upgrade and strengthen their electrical power supply network infrastructures in order to integrate more chargers and charging stations.
For high-voltage circuit cooling purposes, apart from Si IGBTs, SiC MOSFETs, or WBG devices, cooling plates, copper metal-injected heat sinks, spray cooling and jet impingement are additionally and widely recommended. They can be used in the future for further, immediate cooling and to reduce harmonics and parasitic impedances. To achieve higher power density and performance improvements, Reference [
248] recommended that insulation materials be fully microporous, that the thermal management system be improved, and that traditional highlighted materials, such as diamonds, be used for electrical isolation.
Concerning the electric motors, the widened use of coils, changes in the windings, and proper stator or rotor designs are recommended as measures to reduce vibrations and interference. In line with these steps, skewed or double stator or radial rotor topologies will help mitigate vibrations and electromagnetic interference [
249]. According to References [
250] and [
112], because magnets may eventually be absent from future electric motors , limitations on the use of permanent magnet electric motors, or their replacement by switched reluctance motors (SRMs), is suggested. A two-stack conventional switched reluctance motor is depicted in the following figure (
Figure 10).
Further, as magnets may be reduced in mass or entirely absent from motors in the future, as noted above, it is recommended that this reduction in magnet mass be achieved through variations of magnet size in the axial direction.
According to Reference [
161], supercapacitors should operate at low temperatures and frequencies, in order to achieve greater capacity and to improve their performance. For this purpose, a reduction in series resistance is proposed, either by reducing the applied voltage or by operating at low temperatures. Generally, they need control, so supercapacitors should often be overloaded. Thus, frequent operation and maintenance are recommended, including even replacement with supercapacitors that are smarter and more durable and effective. Redox-active organic compounds [
251], nickel oxides [
252], 3D graphene or graphene oxide [
253], inorganic oxides, metal nitrides [
254] or mesoporous materials [
254] are recommended for wider use as electrode materials in the future. Polyethylene can be inserted as a separator for better power storage [
255]. It is also suggested that in some driving situations, the electric motor be operated as a generator to charge the supercapacitors.
Regarding operation of the whole vehicle, to prevent a possible battery ignition and inform the driver about possible faults, a system for measuring voltage, current and internal resistance or detecting a possible Hall effect can be proposed that, through Wi-Fi, may alert the driver, with alarms and indices on his/her mobile phone or tablet, about the condition of the vehicle, even when the electric motor is switched off.
Generally speaking with regard to the near future, it is of great importance that electric vehicles have well-maintained, integrated equipment with more sensors or fuses for better and safer operation, e.g., to avert equipment component failures or overvoltages in the event of a vehicle fault. It is recommended that repair technicians trained to repair and maintain electric vehicles perform short circuit and overheating tests during car maintenance.
Concerning hybrid electric vehicles, in order to eliminate torque losses and for better transmission, functions using additional pumps, dampers and flywheels are suggested. While studies have assessed hybrid vehicles with common fuels (e.g., diesel fuel), the use of synthetic fuels such as hydro-treated vegetable oil, biomass or electrofuels also would help to reduce emissions. Maybe in the future, hybrid cars with biofuels will appear. According to References [
124,
256], in terms of lubrication, lubricants with mineral or synthetic oils (oils with phosphorus and sulfur added) can be suggested, whereas new additive packages containing little or no-sulfated ash, phosphorus or sulfur anti-wear additives can be used in future engine oils.
For future hydrogen fuel cell cars, Reference [
179] proposed one or two more sensors in the vehicle’s cabin and next to the electric motor, as well as more sensors next to the tank, in order to detect any leaks or possible damage and to release hydrogen and adjust it to permissible low levels. Additional sensors are suggested because there should be no hydrogen leakage into the cabin, as hydrogen is explosively flammable and could cause the car to be blown up or burst into flames. According to Reference [
15], it is advisable to avoid overfilling tanks and any increased pressurization or overheating of the hydrogen in the tanks to ensure that the temperature does not exceed 85–115 °C. Based on Reference [
185], due to the expected increase in the use of hydrogen as a fuel in the future, applications that inform drivers about the availability of a station and guide them to it, thus helping them to more easily reach fuel stations for hydrogen, are generally suggested.
As for vehicle traffic, in addition to any warning signals, it is suggested that mobile or tablet applications be developed to alert pedestrians and cyclists of an electric car approaching or crossing next to them, even with a loud noise, and to provide information about the vehicle. Moreover, as noted in Reference [
257], additional infrastructure for transporting blind or elderly people, such as auxiliary and special markings with specific lighting and sound, or sound that is not disturbing to blind people, may help in traffic and are recommended for consideration.
In the end, in order to help drivers with perceiving potential hazards from pedestrians and cyclists, mobile applications and devices are recommended, such as upgraded and dedicated short-range communication (DSRC) device-roadside units. According to References [
258] and [
259], these units (based on IEEE 802.11p and IEEE 1609 standards) alert drivers to adverse driving conditions wirelessly, as developed to facilitate the provision of wireless access in vehicular environments. These technologies will help in avoiding accidents with pedestrians and cyclists (mainly in urban areas).
To reduce electromagnetic interference, noise and harmonic currents in parallel with the function of piezoelectric energy harvester systems, effective cable shielding and electric ground designs, non-excessive operation or overloads, and frequent good maintenance of the equipment are recommended. For effective cable shielding, 3D-metallized sponges (silver nanowire melamine sponges) are suggested in Reference [
260]. Further, the use of carbon nanotubes or reinforced polymers will reduce electromagnetic interference, according to Reference [
261]. Aerodynamic designs and changing the weight distribution of the vehicle will help in reducing electromagnetic interference.
Specifically, for autonomous driving, it is recommended that basic equipment, such as 3D cameras, lidars, radars, 3D maps for navigation and anti-malware, be programmed and frequently updated so that passengers can move safely to their destination and any malicious acts or cybersecurity issues can be prevented. If navigation errors occur due to incorrect programming of the maps or prerecorded maps that do not function well, then preinstalled maps in mobile phones can help with the car’s navigation. The development of an SOS button to place calls to ambulance services in the event of a traffic accident is also recommended, as well as additional advanced sensors to identify pedestrians and cyclists and air pollution and radiation sensors to detect background ionization, all for better vehicle mobility and behavior [
262]. In order to prevent accidents involving pedestrians and cyclists, the development of a mobile phone application is recommended to alert them of an approaching electric car or the passage of an autonomous vehicle. Finally, in [
239], it is recommended that artificial intelligence be introduced for use in driving the vehicle for the purposes of pedestrian identification, as well as anti-theft or carjacking protection systems to prevent such incidents.
10. Discussion
The purpose of this review paper was, through advances in electric car equipment regarding safety issues, to propose additional innovations, applications or technologies, as well as materials. Thus, potential future advances in the main equipment were studied. The equipment will evolve in order to withstand greater voltage and current than common at present and to ensure safer and better use of the car. Despite the evolution of the equipment, overvoltages, overcurrents, vibrations and electromagnetic interference will continue to appear in future electric cars. It seems that various proposed systems, technologies, components, and materials will help to mitigate these issues and increase the safety of these cars. Many researchers have proposed additional technologies, applications or materials for use in the future. So, a wider framework for the reduction and elimination of faults that develop in these cars can be discussed and recommended for the future.
Usually, materials such as nanomaterials, Li-alloys Si-alloys, graphene, oxides are recommended for future applications. New proposals include suggestions for the use of highlighted materials in the insulation of high-voltage circuits, such as diamond [
248] or mesoporous materials (e.g., mesoporous silica) for supercapacitor electrodes [
254] or thermoplastic esters as materials in the insulation of battery packs (or other parts) [
242], and even redox active compounds in battery electrodes [
251]. Other materials, such as those with magnetic properties, could also be recommended, due to the fact that magnets will not be used in the future (soft magnetic composite materials in axial flux motor designs for high performance and low eddy currents, for example) [
263]. Moreover, the extension of the use of some materials to other parts of the equipment, such as the use of redox active organic compounds in supercapacitors, is also suggested for the future [
251].
Concerning electric vehicle charging, besides charging at home or in park stations, there is the option of wireless charging during car movement. Because the placement of prefabricated modules under the road surface is expensive, which will be an obstacle to their widespread use, other methods of vehicle charging could be suggested, such as the installation of magnetic coils in parking lots, in order to transmit electric power through the air as a magnetic field. Additionally, monitoring and power boosting could be discussed with electricity distribution operators (DSOs), so that many cars could be charged at one point at the same time without disrupting the grid.
Another problem is the existence of vibrations, noises, harmonics and electromagnetic interference. Ways of addressing them include the use of piezoelectric materials and/or dampers, the use of improved power electronics or better equipment designs, e.g., coils and windings in electric motors. Aside from the use of more piezoelectric materials or dampers, one could also propose the use of materials or parts such as 3D-metallized sponges, carbon nanotubes or reinforced polymers [
260,
261]. Various companies have proposed the use of more bearings and tolerance rings near mechanical components of the vehicle or the use of synthetic lubricants [
264].
Another problem is the lack of infrastructure and auxiliaries for the movement of people (elderly, children or blind people). Although some proposals were made for the future, obtaining more measurements for the movement of pedestrians is a matter for further discussion: for instance, more auxiliaries for pedestrians, cyclists or vulnerable people, in order to further enhance the development of electromobility and assist in the safe movement of pedestrians and bicycles, preventing traffic accidents. Finally, the use of applications for easy and safe movement should be discussed mainly for children.
Because the use of electric vehicles will be widespread in the future, in general, more applications that make the use of these vehicles easier and safer should be developed, such as applications that notify the driver in case of a fault, or that monitor the charge of the vehicle, as well as applications that facilitate pedestrian movement and interaction with electric vehicles or DSRC devices [
258,
259]. Of course, the training of technicians is another topic that needs to be developed. There should be a discussion about the organization of seminars or workshops to provide technicians with more knowledge about electric cars and the skills to perform more overvoltage tests, short circuit tests, overheating tests or function controls and repair these cars easily and properly. Frequent monitoring, upgrades and maintenance of the equipment will help to prevent faults, thus preventing accidents and enhancing the smooth operation of the vehicles.
In the end, in terms of infrastructure for autonomous driving, there have been many debates over whether governments should maintain existing infrastructure or start implementing more digitized and technologically advanced infrastructure to accommodate self-driving cars, according to Reference [
265].
11. Conclusions
In this review paper, a study was carried out with consideration for advances in electric vehicles and charging equipment and the estimations by researchers of how the equipment will evolve in the future with regard to safety issues, in order to make recommendations for the improvement of equipment and enhancing safety.
Specifically, new applications and materials were proposed for the future, with reference to works listed in the bibliography. Besides new applications, additional cooling systems for the battery or high-voltage circuits, function systems, new technologies for electric motors, alternative fuels, additional sensors and new materials such as highlighted materials for wiring high-voltage circuits (e.g., diamond or mesoporous materials), materials with magnetic properties (soft magnetic composites), or even 3D-metallized sponges for effective cable shielding were proposed. Moreover, additional aids that can help with vehicle movement and communication, such as DSRC devices, auxiliary and special markings with specific lighting and sound, or SOS buttons for notification in emergencies were discussed. These new, complementary proposals for functional additions to the equipment or for new materials will aid in the proper operation and charging of electric vehicles and increase the safe operation and handling of basic equipment in electric or self-driving cars in the future and can also alert pedestrians and cyclists to electric vehicle traffic. They will also facilitate safer car movement in general, because in the future, the cars will be able to operate with higher voltage and current and have a greater driving range with one filling or charge, while overvoltages and electromagnetic interference will occur more frequently.
Although this study was focused on electric, hybrid electric, hydrogen fuel cell and self-driving cars, it could be extended to other electric vehicles such as buses, trucks, trains, and bicycles. In any case, drivers should follow the safety regulations and recommendations for better and safer vehicle operation.