When trying to answer the questions such as how to package all the resources organically into the future grid that is dominated by renewable energy power, how to transport a large amount of electricity over a long distance and how to effectively guarantee the safety and stability of the grid and reliability of electricity supply we may start from the study of grid architecture and operation mode.
3.1. The Architecture of Future Power Transmission Grid
The future power grid will mainly include the transmission and distribution system and distributed network for the end user. Of these, the transmission network will play a key role in the wholesale electricity market, because most of the renewable energy sources are far from the load centers. Therefore, this paper will emphasize the structure of the future transmission network.
Table 1.
Four basic transmission modes in current grid.
In the early stages of grid development, the capacity of generating units is relatively small as well as the demands on electricity, so the architecture of the grid is basically from a power plant to the receiving end (here the receiving end refers to one load center or power supply area), which is defined here as power to consumer transmission mode (P-C mode). Later, with the continuous expansion of the capacity of generating units and power plants, power to multiple consumers mode (referred as the P-MC mode) has been developed, that is from power plant to multiple receiving ends. With the increasing demand on electricity, the consumer begins to have higher and higher demands of the reliability of the power supply. One power plant is unable to meet the need of the consumer any more, which leads to the build-on of multiple power sources to the consumer transmission mode (referred to as the MP-C mode) that supplies one receiving end from multiple power sources. In addition, with the multifaceted requests on power supply reliability, power grid interconnection and operational management, the architecture of the grid become increasingly complex, which brings about the transmission mode of multiple receiving ends supplied with multiple powers through load-center substations (that is multiple powers to multiple consumers, referred as MP-MC mode).
Table 1 shows the four basic transmission modes in the current grid. From the point of view of grid architecture, the current grid is basically the combination of P-C, P-MC, MP-C, MP-MC transmission modes, but currently the MP-MC mode hasn’t been the dominant mode of transmission system, besides there is no obvious coordination and complementarity among the various power plants because the plants are operated independently, therefore the MP cannot be completely taken as an organically combined “power package”.
It would be an inevitable choice to upgrade the MP-MC mode to be the leading mode of the transmission network in the future grid if the receiving ends are supplied with stable and reliable electricity. The justifications are as follows: first, it is very difficult to supply stable and reliable electricity to the consumer whether using P-C mode or P-MC mode because a single power plant is incapable of providing sufficient and stable power, unless high-power and high-capacity energy storage systems were built. However, these energy storage systems are not only very high in cost and low in efficiency, but the technology is still immature (except for the pumped storage, but it is very difficult or even impossible to build a large number of pumped storage stations in many solar and wind-rich areas or load centers). Secondly, MP-C mode might be able to provide a more stable and reliable electricity supply to the consumer if the power structure is reasonably designed, but it actually breaks down the power grid into multiple independent electricity networks, which makes it difficult to bring into play the comprehensive advantages of optimal allocation of resources, economy and reliability of interconnected power grid within a wide range. It is hard for the MP-C mode to become the dominant mode, especially considering the diversity of energy resources in the future, as well as the mismatch between the spatial and temporal distribution of resources and load centers.
Based on the above understandings, we propose that the basic structure of the future transmission network will be more realistic and superior if the modes shown in
Figure 1 are used.
First, we make full use of the complementarities of various centralized power plants (solar photovoltaic power, solar thermal power, wind power and ocean energy power generation, etc.) in a given region and link these plants together using the “super busbar” (referred as SBB, which can be achieved by using superconducting power cable) through a unified coordination and control technology so as to package them into a large virtual power plant (LVPP). For instance in China, we can build many LVPPs via different combinations in the areas of Xinjiang Province, Gansu Province, western and eastern Inner Mongolia, northeast of China and coastal areas relying on a variety of resources and power generation modes. The purpose of the portfolio is to make the power output of LVPP smoother, predictable and controllable to some extent compared to one single power plant. Then the electricity can be transported from SBB to the consumer by the high-voltage transmission.
Secondly, here the receiving end refers to a load center (such as Bohai Sea area, Yangtze River Delta area,
etc.) or a power supply area (such as Hunan Province or central China, Chongqing city or Sichuan Province,
etc.). The receiving end can receive power from multiple LVPPs, which is connected to the ring busbar (RBB) of the receiving end. As the LVPPs located in different regions also have good resource complementarities, the receiving end can obtain relatively stable and reliable electricity via the RBB. The biomass power generation, nuclear power and electric vehicle charging stations can be accessed to the RBB of the receiving end according to the local conditions to regulate the power. Thus, each user within the receiving end can be supplied with relatively stable and reliable electricity from the RBB. Thirdly, we can increase the connection line and install the two-way power exchange control device (TPEC) among the SBBs of each LVPP and the RBBs of each receiving end, by this way, not only the power sources of each receiving end are effectively interconnected, but it can be connected together with a number of LVPPs to build a “wide-area super virtual power plants” (WASVPP) [
2].
Figure 1.
Basic structure of the transmission network in the future.
Figure 1.
Basic structure of the transmission network in the future.
With the above transmission modes, the consumers may access stable and reliable supplies of electricity from the “cloud powering” generated by WASVPP (and the distributed power system as discussed below), rather than from one or several central plants, which just like the users in the Internet can access Cloud Computing. In this case, even if a few lines are removed because of failures, there will be no large scale blackouts. Fourthly, it can be connected to the transnational power grid via SBB of LVPPs or RBB of the receiving ends, thereby making it possible to balance the power of the system using the complementarity of resources within a wider context and to achieve international energy trade.
The features mentioned above are just the basic architectural structure of the transmission network in the future. For a specific transmission network, it can be reasonably designed and built based on this basic mode according to the distribution of power and load.
3.2. Operation Mode of the Future Power Grid—DC-Dominated Mode
3.2.1. The Future Transmission Power Grid—A DC-Dominant Grid
The current transmission system dominated by the alternating current (AC) has prominent stability problems. Power system stability refers the overall attributes of the power, network and load. There are many reasons that result in power system stability problems, among which imbalance of instantaneous power is a very important factor. With the continuous expansion of the modern transmission network, the dangers of large scale power blackouts caused by the accidents are increasing [
10]. The collapse of the large power grids and large scale blackouts caused by the great disturbances has caused great losses of production and services. The stability issue has become a constraint bottleneck in the development of modern power systems. In the future, the capacity and scale of the transmission network will be further expanded, but renewable-energy-based power, especially wind energy, has intermittent and instability characteristics, which bring enormous challenges to the large power system dominated by AC. In response to this challenge, therefore, the dominant operation mode of the future transmission network also needs new ideas.
As we all know, compared with the AC transmission, DC transmission has many advantages, mainly as follows: (1) DC transmission is not subject to the stability problem that is inherent for AC transmission, and its transmission distance and power are not restricted by the synchronous operation of the power system; (2) There is no capacitance current, no reactance drop when the DC line is operated in a steady-state, and the voltage distribution along the line is relatively stable, and no reactive compensation is needed; (3) It is easier and quick to regulate and control the power and current of DC transmission lines; (4) When transporting the same power, the DC lines are low cost, relatively simple in the tower structure of overhead lines, and compact in corridors, and the cable with the same insulation level can be run at a higher voltage; (5) It is not required to run synchronously for the AC system that is linked by DC transmission lines so as to achieve the asynchronous connection between different AC systems; (6) In addition, the DC transmission also has low line loss and small disturbance of the communication. Therefore, DC transmission has been receiving more and more widespread attention, and has been applied in many areas in the power system.
The power transmitted in the future transmission system will be much higher than that of the modern power grid, then the DC transmission can not only improve the transmission capacity, but also avoid the stability problem caused by the AC transmission, and thus help to improve safety and reliability of power transmission network. With the continuous technology improvement, cost reduction and reliability increase of the power electronics with high-voltage and high-power as well as the increase of availability of converter stations, the DC transmission technology will play a more important role in future grid. Presently, the R&D of high voltage direct current (HVDC) circuit breaker, multi-terminal HVDC systems and its operation and control have been receiving increasingly widespread attention. It is foreseeable that constructing the future DC-driven transmission network using the DC transmission will be a very reasonable choice.
3.2.2. The Future Distribution Network—A DC-Dominant Network
At present, the structure of load in the power grid is approximately as follows: motors account for 65%, lighting about 15%, information devices about 10% and others (mainly electrochemical, electrolytic plating and heating equipment) 10%. Of these loads, the information devices, electrochemical, electrolytic plating, and a small number of light sources need DC power, but due to the fact that the current distribution system is the AC network, we often use rectification to obtain DC power. With the significant adjustment of energy structure and the continuous development of information technology and new materials technology, the demands of loads to the power will also change dramatically in the future grid, and DC systems with more and more requirements will be present. First of all, electric vehicles will become one of the main loads in the future. As mentioned earlier, the charging load of electric vehicles in China will reach about 500 million kilowatts by 2050, and the charging load of electric vehicles is DC power; Second, with the continuous development and penetration of information technology, information devices (such as computers and microprocessors, communications equipment, intelligent terminals, sensors and sensor networks, etc.) will consume more power, and this equipment also needs DC power; Third, with the growing development of semiconductor lighting technology, it can be predicted that lighting systems in the future will all use LED lighting that is also a DC load; Fourth, the prices of power electronic devices are getting lower and lower, and motors in the future will be driven more and more by a variety of power electronic converters. Currently, the power electronic devices used to drive motors generally use AC-DC-AC power conversion mode, which first converts the AC to DC, and then converts the DC into AC with variable frequency and amplitude to drive motors, thereby to gain better drive performance and higher operation efficiency of the motor systems. It can be seen that the DC power supply can not only eliminate the conversion from AC to DC and reduce the cost of the motor drive systems, but further improve the overall efficiency of the motor drive system. Using DC power, the braking energy of motor systems can directly be feed-backed to the DC power grid without any transformation, which can greatly save power. In addition, when the motor system is driven by DC power, what the motors get from and feedback to the DC power grid is only active power, instead of occurring additional reactive power when supplied by AC power. This can further reduce the network losses and improve the power supply efficiency. Therefore, the motor load in the future will also be put more and more demands on the DC power supply.
It can be seen that the DC power will account for an increasing proportion in the future distribution network. In particular, the DC load will take a dominant role in office areas, residential areas and schools, and other non-industrial load areas. It becomes an inevitable requirement to develop the DC power distribution technology with the changes of load demand on the power. Therefore, the future distribution system will develop gradually towards a DC-based network.
3.2.3. Distributed Power System—DC Mode has Significant Advantages
Renewable energy is one kind of distributed resource, and using this dispersed resource locally will be one of the important features of future energy systems. Therefore, the end user would not only get power from the “Cloud Powering”, but produce electricity to meet their own needs, and sell the power back to the grid when the power production is more than what they need or when the grid has the demand. In the future the electricity network of the end users will be the distributed power system that highly mixes its own distribution network with distributed power generation. The distributed power systems will have even broader applications among non-industrial users due to their rather lower demand on the power.
In a distributed power network, solar photovoltaic power generation will be one of the most common applications, and the electricity from the photovoltaic power generation is DC. Meanwhile, it will be an inevitable choice to apply the distributed energy storage system in order to greatly improve the reliability of power supply and power quality, and most of the energy storage systems need DC power for electricity storage. Considering that the future distribution network tends to develop towards the direction of DC-based system and the proportion of non-industrial consumers using the DC power will reach a very high level, it becomes obvious to apply the DC mode in the distributed power systems. In summary, we believe that the transmission system, distribution network and distributed power system will gradually develop with the DC-based operation mode.