Effect of Rejuvenators on the Workability and Performances of Reclaimed Asphalt Mixtures
1
College of Civil and Transportation Engineering, Hohai University, Nanjing 210098, China
2
School of Traffic and Transportation Engineering, Changsha University of Science and Technology, Changsha 410114, China
*
Author to whom correspondence should be addressed.
Materials 2021, 14(21), 6385; https://doi.org/10.3390/ma14216385
Submission received: 30 September 2021
/
Revised: 17 October 2021
/
Accepted: 22 October 2021
/
Published: 25 October 2021
(This article belongs to the Special Issue Long-Life and Circular Pavement Materials)
Abstract
:The use of rejuvenators has enhanced the workability of asphalt mixtures containing the reclaimed asphalt pavement (RAP). This conclusion is based on the determination of viscosity of asphalt binders, while not validated from reclaimed asphalt mixtures. In this study, the effect of two rejuvenators (ordinary and emulsified rejuvenator) on the workability of reclaimed asphalt mixtures was evaluated by measuring the mixing torque and determining the air void content of reclaimed mixtures. In addition, their effects on the performances of reclaimed mixture were studied via the three indexes tests, rutting test and freeze-thaw splitting tests. The experimental results show that mixing torque and air void content of reclaimed mixtures with the emulsified rejuvenator is 4% and 6% lower than that with the ordinary rejuvenator, respectively. This indicates that improvement of the workability of reclaimed mixtures can be achieved by using an emulsified rejuvenator, but not by an ordinary rejuvenator. That is also the reason that at least 20% greater high-temperature stability is found for reclaimed mixtures by using the emulsified rejuvenator than using the ordinary rejuvenator. In addition, reclaimed mixtures with the emulsified rejuvenator show similar moisture susceptibility to that with the ordinary rejuvenator. This study provides a feasible method to assess the workability effect of rejuvenators on reclaimed mixtures directly and recommends the use of an emulsified rejuvenator to improve the workability and high-temperature stability of reclaimed mixtures.
1. Introduction
The growing attention devoted to environmental conservation and sustainable development, and the utilization of nonrenewable resources, such as oil and minerals, has been limited gradually [1]. That results in the continuous rise in the price of asphalt and aggregates [2]. In China, nearly 790 million tons of reclaimed asphalt pavement (RAP) is produced every year [3,4]. After good regeneration and appropriate mix design, RAP can substitute for the partial asphalt and aggregate in asphalt mixtures [5]. The use of RAP thus has gained more and more popularity due to its environmental and economic benefits [6].
The binder in RAP, however, is highly stiff and viscous after its service life [1]. The asphalt mixtures mixed with RAP are prone to yield fatigue failure and low temperature cracking [7]. Some researchers and engineers recommended using a softer virgin asphalt to recover the properties of aged asphalt to the level that resembles that of virgin asphalt [8,9]. Nevertheless, this method obtains inefficiently little effort when the asphalt binder is heavily aged or more RAP is used [10]. At present, rejuvenators are commonly used in reclaimed mixtures to recover the properties of aged asphalt [11,12]. Therefore, many studies were carried out on the effect of rejuvenators on the properties of aged asphalt and reclaimed mixtures so as to obtain good rejuvenators. It was reported by Zaumanis et al. that the waste vegetable oil-based rejuvenator can largely reduce the performance grade and fatigue parameters of aged asphalt compared to six other types of rejuvenators [13,14]. Waste engine oil can also be used as a rejuvenator and it is found to enhance the mechanical properties and moisture resistance of reclaimed mixtures [15,16]. Furthermore, the use of waste polymer modified asphalt in combination with rejuvenators can significantly improve the fatigue, rutting and moisture resistance of reclaimed mixtures [17]. Rejuvenators can diffuse into aged asphalt resulting in the improvement of the physical properties of aged asphalt, such as being more permeable and softer. It is believed that the rejuvenating effect of rejuvenators is largely dependent on the diffusibility of the rejuvenator into aged asphalt [18]. It is found that the diffusibility of rejuvenators increases with increasing temperature and time [19]. Additionally, rejuvenators with low viscosity diffuse into aged asphalt with more ease.
Based on the effect of rejuvenators on aged asphalt, it seems that the use of rejuvenators can improve the workability of reclaimed asphalt mixtures [20]. It was reported by Ahmad et al. that the vegetable oil-based rejuvenator improved the workability of reclaimed asphalt mixtures due to the reduction in viscosity of aged asphalt [21]. Bio-based rejuvenators, which are refined from cooking oil waste, can also enhance the workability of reclaimed asphalt mixtures [8,22]. It should be noted that the conclusion about the improvement of rejuvenators on the workability of reclaimed asphalt mixtures is based on the determination of the viscosity of the asphalt binder. From the aspect of practical application, it is better to discuss the effect of the rejuvenator on the properties of reclaimed asphalt mixtures directly. In engineering practice, the rejuvenator is required to be heated at relatively high temperature for usage, which will result in the volatilization of the light component and aging of the rejuvenator [19]. If the rejuvenator is emulsified, it can be used without heating and maybe improve the workability of reclaimed mixtures. Therefore, this study was carried out to discuss the effect of rejuvenators on the workability and performances of reclaimed asphalt mixtures. An emulsified rejuvenator was investigated and compared with an ordinary rejuvenator. The workability was evaluated via measuring the torque generated when mixing reclaimed mixtures and determining the air void content of the compacted mix. The performances of reclaimed mixtures include high-temperature stability and moisture susceptibility.
2. Materials Preparation
2.1. Raw Materials
An ordinary rejuvenator meeting ASTM D4552 specification was selected as the control rejuvenator (CR). Table 1 shows the properties of the control rejuvenator. Using this control rejuvenator as a base component, an emulsified rejuvenator (ER) was self-developed and used in this study. Table 2 shows the properties of the emulsifiers used. The detailed preparation procedure of ER is described in Figure 1. The water content by mass of ER was 40%.
Figure 2 presents the images of the two rejuvenators and their rotational viscosity values at different temperatures. It can be visually found from the images that the ER shows better flowability than the CR at room temperature. The rotational viscosity of ER at 20 °C was 300 mPa·s, dramatically lower than that of CR at the same temperature. Therefore, it is believed that ER can be used without heating in engineering practice. Styrene-butadiene-styrene (SBS) modified asphalt binder, PG 76-22, was used as the virgin asphalt and the fundamental material to produce laboratory-aged asphalt. The rotational viscosity of this modified asphalt at 135 °C was 2690 mPa·s and the G*/sinδ at 76 °C was 2.26 kPa. These tests were performed according to ASTM D4402 and AASHTO T315.
The RAP material was obtained from the upper layer of a freeway which has already been serviced for 11 years. After preprocessing, the RAP material was divided into three groups: 10~16 mm, 5~10 mm, and 0~5 mm. According to ASTM D2172, the asphalt content of RAP with corresponding size is determined as 2.3%, 1.6% and 7.0%, respectively. In addition, the gradations of extracted aggregates are determined and presented in Table 3. The virgin aggregates were basalt and mineral filler was limestone.
2.2. Preparation of Recycled Asphalt Binders
Recycled asphalt binders were prepared to evaluate the regeneration effect of the rejuvenators on aged asphalt. Prior to preparing recycled asphalt, laboratory-aged asphalt was first obtained via aging the SBS-modified asphalt in a rolling thin film oven (RTFO) at 163 °C for 5 h [23]. This method allows for sufficient aged asphalt to be collected within a short period of time. After that, preparation of recycled asphalt binder was accomplished by blending aged asphalt, virgin asphalt and rejuvenator together at 175 °C for 2 h. The weight ratios of aged asphalt to total recycled asphalt binder were 30%, 50% and 100%. It is noted herein that CR and ER was added in accordance with different contents. The contents of CR and ER were set at 4% and 6.67% by weight of aged asphalt, respectively, which was done to ensure equal weight of pure rejuvenator in recycled asphalt.
2.3. Mix Design of Reclaimed Asphalt Mixtures
With standard SMA-13 gradation, the reclaimed asphalt mixtures were designed for workability and performance tests. The RAP content in the reclaimed mixtures was 0% (virgin asphalt mixtures), 30% and 50%, respectively. As depicted in Figure 3, the combined gradations of those asphalt mixtures were designed as close as possible to eliminate the interference of gradation. Based on Marshall mix design, the asphalt contents were determined as 6.0% for these reclaimed mixtures (see Table 4).
3. Evaluation Methods
3.1. Workability Evaluation Methods
The rotational viscosity of asphalt binder is commonly used to determine the mixing and compaction temperature of asphalt mixtures [24]. Similarly, the workability of asphalt mixtures is also reflected in the mixing and compaction process [25]. In this study, the workability in the two process was assessed by measuring mixing torque and determining air void content of compacted mix, respectively.
3.1.1. Measurements of Mixing Torque
It is confirmed in many previous studies that the torque generated when stirring asphalt mixtures is highly related to the mixing workability of mixtures [26,27,28]. The lower mixing torque means the better workability of asphalt mixtures. In this study, the mixing torque was used to characterize the workability of reclaimed asphalt mixtures. A device that can measure the torque was self-fabricated and used. Figure 4 shows a photograph of this device, which mainly consists of (1) motor box (ANGNI, AN1000, Shanghai, China), (2) mixing paddle, (3) metal bucket, and (4) thermostat. The motor allows the device to stir at different speeds. Importantly, the device includes a data-acquisition system that enables it to record the torque readings automatically.
The reclaimed mixtures with RAP content of 30% was selected for this test and virgin mixtures were used as the control group. According to trial and error, each batch of asphalt mixtures for testing weighed 800 g approximately, which ensured the stable data during mixing process. The mixing temperatures were set at 130 °C, 150 °C and 170 °C. Prior to testing, the mixtures were heated 5 °C higher than mixing temperature in an oven. Upon completing the heating step, the mixtures and rejuvenator were placed into the metal bucket. The mixing paddle started to rotate at a constant speed of 100 r/min. Meanwhile, data-acquisition system was lunched to record the torque values. The test lasted approximately 3 min in general.
3.1.2. Determination of Air Void Content
There is a method of evaluating the workability of asphalt mixtures in compaction process, which is determined with the use of air void content of specimens produced with Marshall compactor [25,29]. The better workability of asphalt mixtures can be obtained if the air void content is lower. In this study, Marshall specimens were firstly prepared following mix design in Table 4. Then, the air void contents of these specimens were tested to assess the workability. The detailed procedures are as follows.
- The RAP, virgin aggregates and virgin asphalt were heated at 140 °C, 180 °C and 170 °C for 2 h, respectively. The CR was heated to 110 °C, while the CR was used at room temperature without heating;
- The RAP was premixed with rejuvenator in a laboratory mixer (model F-20, Changji, Shanghai, China). The virgin aggregates, virgin asphalt and powder were successively added into the mixer for mixing. Each mixing duration was 60 s;
- After mixing, the loose reclaimed mixtures were subjected to heat preservation in an oven. The preserved temperature was 160 °C and preserved time was 1 h;
- Marshall specimens were prepared with 75 blows per side following the Chinese specification JTG-E20 T0702. Lastly, surface-dry method was used to measure the air void content.
3.2. Performances Evaluation Methods
3.2.1. Three Indexes Tests
Three indexes of asphalt binder refers to the softening point, the penetration and the ductility. To evaluate the regeneration effect of rejuvenator on the aged asphalt, three indexes tests were performed on the recycled asphalt binders. These test methods referred to the ASTM D36, D5, and D113, respectively.
3.2.2. Rutting Test
The rutting test was performed in accordance with JTG-E20 T0719 to evaluate the high-temperature stability of reclaimed mixtures [24]. The test temperature was 60 °C and the wheel pressure was 0.7 MPa. After testing, the dynamic stability (DS) was determined to evaluate the high-temperature stability.
3.2.3. Freeze-Thaw Splitting Tests
It is essential to evaluate the moisture susceptibility of reclaimed asphalt mixtures when using emulsified rejuvenator, since moisture is induced into the rejuvenator. In this study, the freeze-thaw splitting test was used to assess the moisture susceptibility of asphalt mixtures. This test was conducted according to JTG-E20 T0729. Marshall specimens (50 blows for each side) were prepared and then equally divided into dry group and freeze-thaw group. The splitting test was performed for each group to determine tensile strength ratio (TSR), viz. the evaluation index of moisture susceptibility.
4. Results and Discussions
4.1. Effect of Rejuvenators on the Workability of Reclaimed Mixtures
4.1.1. Mixing Torque
The torque values are presented in Figure 5. As expected, the torque values decreased with the increase of temperature due to the reduction in the viscosity of the asphalt binder. The reclaimed mixtures with CR exhibited higher torque values than the virgin mixtures at the same testing temperatures. The higher torque values for reclaimed mixtures can be attributed to the aged asphalt in RAP, which was more stiff and viscous than the virgin asphalt. This also gives a reasonable explanation as to why production temperature for reclaimed asphalt mixture is required to be 5~10 °C higher than that for virgin mixtures in Chinese specification JTG T55-2019 [30].
By comparing the torque values obtained from the reclaimed asphalt mixtures, it can be seen that reclaimed mixtures with ER showed lower torque values than that with CR, indicating that ER helped to improve the workability of reclaimed mixtures. This can be due to that compared to oil mediums, the oil-water emulsified film showed better lubricating effect during the mixing process [31]. The resistance between aggregates particles, thus, was reduced. Furthermore, the greater difference in torque values for the reclaimed mixtures at higher temperature (150 °C and 170 °C) can be obtained. The torque values for reclaimed mixtures with ER were even lower compared to virgin mixtures.
4.1.2. Air Void Content
Figure 6 presents the air void content of the Marshall specimen. The air void content of virgin mixtures was within the limit of 3~4%, while that of reclaimed mixtures with CR exceeded the upper limit. This implies that the addition of RAP in asphalt mixtures exhibited an adverse effect on the workability in the compaction process. By comparing the air void contents between the reclaimed mixtures produced with CR and ER, it can be found that an approximately 6% degree of workability was improved by using ER. These findings are consistent with the results showed by the mixing torque test. Unlike mixing workability, the workability in the compaction process of reclaimed mixtures produced with ER did not exceed the level of that of the virgin mixtures. That result can be seen from the comparison of air void contents of the two mixtures.
4.2. Effect of Rejuvenators on the Performances of Reclaimed Mixtures
4.2.1. Three Indexes of Recycled Asphalt Binders
Test results of three indexes of different asphalt binders are shown in Figure 7. It was found that after long-term aging, the softening point, penetration and ductility of virgin asphalt all decreased. With the incorporation of rejuvenators into the aged asphalt, the softening point decreased, and the penetration and ductility increased. This indicates the performances of the aged asphalt had been partially recovered. However, three indexes of recycled asphalt were difficult to meet the requirements in JTG-F40 specification [32] simultaneously when only rejuvenator was added. In the case of the addition of rejuvenator and virgin asphalt, aged asphalt content can reach to 70% in view of the fact that these indexes of recycled asphalt all satisfied the requirements. In addition, the values of three indexes of recycled asphalt with ER were equivalent to that of recycled asphalt with CR. This may be attributed to complete dissipation of moisture during the preparation process of recycled asphalt or little residual water that basically had no effect on the properties of recycled asphalt [33].
4.2.2. High-Temperature Stability
The dynamic stability (DS) results of each studied mixture are presented in Figure 8. The higher DS means the better high-temperature stability. As can be found in this figure, the DS values of all reclaimed mixtures were higher than that of the virgin mixture. However, the DS values of reclaimed mixtures did not vary monotonously with the increasing RAP content. The sample with 30% RAP content had the highest DS. Among these reclaimed mixtures, the mix with CR showed lower DS than the mix with ER, indicating that using ER in reclaimed mixtures results in better high-temperature stability. It was found above that the use of ER improved the workability of reclaimed mixtures, which results in lower air void content in reclaimed mixtures (see Figure 6). This may be the reason why better high-temperature stability of reclaimed mixture with ER was obtained.
4.2.3. Moisture Susceptibility
Figure 9 shows the tensile strength ratio (TSR) of the mixtures. Obviously, the TSR of reclaimed mixtures was lower than that of virgin mixtures, indicating that the use of RAP in asphalt mixtures is adverse to the moisture sensibility. There are two probable factors contributing to the worse moisture susceptibility of reclaimed mixtures. The first is that low surface free energy of aged asphalt weakens the bond between aggregates and aged asphalt [34]. The aged asphalt strips from the RAP particles with more ease under the freeze-thaw condition, which results in the water damage. The second can be that the incomplete blending between virgin asphalt and aged asphalt yields a weak interface, and water damage tends to occur at this interface easily [35]. The reclaimed mixtures with ER exhibited the nearly equivalent TSR to that with CR, although water was induced in ER. Overall, all studied mixtures had good moisture susceptibility, because these specimens showed TSR values beyond the requirements in Chinese JTG-F40 specification.
5. Conclusions
The effects of an ordinary rejuvenator and self-developed emulsified rejuvenator on the workability of reclaimed asphalt mixtures were compared by measuring the mixing torque and determining the air void content. Additionally, their effects on the high-temperature stability and moisture susceptibility of asphalt mixtures were evaluated. Based on the test results, some major conclusions can be drawn as follows.
- i.
- The emulsified rejuvenator can be used without heating in engineering practice owing to its low viscosity, while the ordinary rejuvenator has to be heated.
- ii.
- The addition of RAP into asphalt mixtures has an adverse effect on the workability. Compared to using an ordinary rejuvenator, reclaimed mixtures prepared using the emulsified rejuvenator exhibit lower torques and air void contents. This can be attributed to that using oil-water emulsified medium shows better lubricating effect during the mixing and compaction process.
- iii.
- Reclaimed mixtures with the emulsified rejuvenator show similar moisture susceptibility to that with the ordinary rejuvenator. At least 20% higher high-temperature stability is obtained for reclaimed mixtures by using the emulsified rejuvenator than an ordinary rejuvenator. This can be attributed to better workability when using the emulsified rejuvenator, which results in lower air voids content in the reclaimed mixtures.
- iv.
- The emulsified rejuvenator improves the workability and high-temperature stability of reclaimed mixtures, while not affecting the moisture susceptibility of mixtures. Therefore, rejuvenators are recommended to be emulsified for use in practice.
Author Contributions
Conceptualization, W.T., F.D. and X.Y.; methodology, W.T. and N.L.; formal analysis, W.T.; investigation, W.T.; data curation, Y.Z. and Z.W.; writing—original draft preparation, W.T.; writing—review and editing, X.Y.; supervision, X.Y.; project administration, W.T. and N.L.; funding acquisition, W.T. and N.L. All authors have read and agreed to the published version of the manuscript.
Funding
This research was funded by Postgraduate Research & Practice Innovation Program of Jiangsu Province, grant number KYCX21_0496 and Fundamental Research Funds for the Central Universities, grant number B210202050.
Institutional Review Board Statement
Not applicable.
Informed Consent Statement
Not applicable.
Data Availability Statement
No new data were created or analyzed in this study. Data sharing is not applicable to this article.
Acknowledgments
The authors express their appreciation to Jiangsu Highway Engineering Maintenance Co., Ltd. for providing the RAP materials.
Conflicts of Interest
The authors declare no conflict of interest.
References
- Ding, Y.J.; Huang, B.S.; Shu, X. Blending efficiency evaluation of plant asphalt mixtures using fluorescence microscopy. Constr. Build. Mater. 2018, 161, 461–467. [Google Scholar] [CrossRef]
- Ding, Y.J.; Huang, B.S.; Shu, X. Characterizing blending efficiency of plant produced asphalt paving mixtures containing high RAP. Constr. Build. Mater. 2016, 126, 172–178. [Google Scholar] [CrossRef]
- Li, N.; Zhan, H.; Yu, X.; Tang, W.; Xue, Q.L. Investigation of the aging behavior of cellulose fiber in reclaimed asphalt pavement. Constr. Build. Mater. 2021, 271, 121559. [Google Scholar] [CrossRef]
- Gao, J.; Yang, J.G.; Di, Y.; Jiang, Y.; Ruan, K.G.; Tao, W.J.; Sun, C.; Luo, L.H. Reducing the variability of multi-source reclaimed asphalt pavement materials: A practice in China. Constr. Build. Mater. 2021, 278, 122389. [Google Scholar] [CrossRef]
- Rafiq, W.; Napiah, M.; Habib, N.Z.; Sutanto, M.H.; Alaloul, W.S.; Khan, M.I.; Musarat, M.A.; Memon, A.M. Modeling and design optimization of reclaimed asphalt pavement containing crude palm oil using response surface methodology. Constr. Build. Mater. 2020, 291, 123288. [Google Scholar] [CrossRef]
- Sreeram, A.; Leng, Z.; Zhang, Y.; Rabindra, K.P. Evaluation of RAP binder mobilisation and blending efficiency in bituminous mixtures: An approach using ATR-FTIR and artificial aggregate. Constr. Build. Mater. 2018, 179, 245–253. [Google Scholar] [CrossRef]
- Moghaddam, T.B.; Baaj, H. The use of rejuvenating agents in production of recycled hot mix asphalt: A systematic review. Constr. Build. Mater. 2016, 114, 805816. [Google Scholar] [CrossRef]
- Yu, J.M.; Guo, Y.F.; Peng, L.; Guo, F.; Yu, H.Y. Rejuvenating effect of soft bitumen, liquid surfactant and bio-rejuvenator on artificial aged asphalt. Constr. Build. Mater. 2020, 254, 119336. [Google Scholar]
- Ekblad, J.; Lundstroam, R. Soft bitumen asphalt produced using RAP. Mater. Struct. 2017, 50, 13. [Google Scholar] [CrossRef] [Green Version]
- Ma, H.; Mao, Q.; Li, N. Influence factors of RAP content in plant-mixed hot recycling asphalt pavement. J. Chongqing Jiaotong Univ. Nat. Sci. 2020, 39, 97–104. (In Chinese) [Google Scholar]
- Ech, M.; Tintillier, P.; Baaj, H.; Richard, N. Asphalt Mixture without Virgin Bitumen Based on Recycled Materials. U.S. Patent Publication Number 20140033951, 6 February 2014. [Google Scholar]
- Zaumanis, M.; Mallick, R.B.; Robert, F. Evaluation of rejuvenator′s effectiveness with conventional mix testing for 100% reclaimed asphalt pavement mixtures. Transp. Res. Rec. 2013, 2370, 17–25. [Google Scholar] [CrossRef] [Green Version]
- Zaumanis, M.; Mallick, R.B.; Poulikakos, L.; Robert, F. Influence of six rejuvenators on the performance properties of reclaimed asphalt pavement (RAP) binder and 100% recycled asphalt mixtures. Constr. Build. Mater. 2014, 71, 538–550. [Google Scholar] [CrossRef]
- Zaumanis, M.; Mallick, R.B.; Frank, R. Evaluation of different recycling agents for restoring aged asphalt binder and performance of 100% recycled asphalt. Mater. Struct. 2015, 48, 2475–2488. [Google Scholar] [CrossRef]
- El-Shorbagy, A.M.; El-Badawy, S.M.; Gabr, A.R. Investigation of waste oils as rejuvenators of aged bitumen for sustainable pavement. Constr. Build. Mater. 2019, 220, 228–237. [Google Scholar] [CrossRef]
- Woszuk, A.; Wróbel, M.; Franus, W. Influence of waste engine oil addition on the properties of zeolite-foamed asphalt. Materials 2019, 12, 2265. [Google Scholar] [CrossRef] [Green Version]
- Daryaee, D.; Ameri, M.; Mansourkhaki, A. Utilizing of waste polymer modified bitumen in combination with rejuvenator in high reclaimed asphalt pavement mixtures. Constr. Build. Mater. 2020, 235, 117516. [Google Scholar] [CrossRef]
- Kuang, D.L.; Jiao, Y.; Ye, Z.; Lu, Z.H.; Chen, H.Y.; Yu, J.Y.; Liu, N. Diffusibility enhancement of rejuvenator by epoxidized soybean oil and its influence on the performance of recycled hot mix asphalt mixtures. Materials 2018, 11, 833. [Google Scholar] [CrossRef] [PubMed] [Green Version]
- Kuang, D.L.; Feng, Z.G.; Yu, J.Y.; Chen, X.; Zhou, B. A new approach for evaluating rejuvenator diffusing into aged bitumen. J. Wuhan Univ. Technol. 2011, 26, 43–46. [Google Scholar] [CrossRef]
- Jain, M.A.; Sharma, A.; Sharma, D.K. Use of edible oil as rejuvenator in reclaimed asphalt pavement. In Proceedings of the a National Conference on Roads and Transport (NCORT-2017), Roorkee, India, 14–15 October 2017. [Google Scholar]
- Ahmad, K.A.; Abdullah, M.E.; Hassan, N.A.; Usman, N.; Hassan, R.M.; Bilema, M.A.; Saeed, S.M.; Batari, A. Effect of bio based rejuvenator on mix design, energy consumption and GHG emission of high RAP mixture. In Proceedings of the 4th International Conference on Civil and Environmental Engineering for Sustainability (IConCEES 2017), Langkawi, Malaysia, 4–5 December 2017. [Google Scholar]
- Gong, M.H.; Yang, J.; Zhang, J.Y.; Zhu, H.R.; Tong, T.Z. Physical–chemical properties of aged asphalt rejuvenated by bio-oil derived from biodiesel residue. Constr. Build. Mater. 2016, 105, 35–45. [Google Scholar] [CrossRef]
- Qian, Y.; Guo, F.; Leng, Z.; Zhang, Y.; Yu, H.Y. Simulation of the field aging of asphalt binders in different reclaimed asphalt pavement (RAP) materials in Hong Kong through laboratory tests. Constr. Build. Mater. 2020, 265, 120651. [Google Scholar] [CrossRef]
- Ministry of Transport of the People’s Republic of China. JTG E20-2011-Standard Test Methods of Bitumen and Bituminous Mixtures for Highway Engineering; Ministry of Transport of the People’s Republic of China: Beijing, China, 2011.
- Thomas, M.; Gerald, R.; Walaa, M.; Karissa, M. Assessment of workability and compactability of warm-mix asphalt. Transp. Res. Rec. 2010, 2180, 36–47. [Google Scholar]
- Tao, M.J.; Mallick, R.B.; Robert, F. Effects of warm-mix asphalt additives on workability and mechanical properties of reclaimed asphalt pavement material. Transp. Res. Rec. 2009, 2126, 151–160. [Google Scholar] [CrossRef]
- Wang, C.; Hao, P.W.; Ruan, F.; Zhang, X.Y.; Adhikari, S. Determination of the production temperature of warm mix asphalt by workability test. Constr. Build. Mater. 2013, 48, 1165–1170. [Google Scholar] [CrossRef]
- Ali, A.; Abbas, A.; Nazzal, M.; Alhasan, A.; Roy, A.; Powers, D. Workability evaluation of foamed warm-mix asphalt. J. Mater. Civ. Eng. 2014, 26, 93–101. [Google Scholar] [CrossRef]
- Kowalska, A.C.; Gardziejczyk, W.; Iwanski, M.M. Moisture resistance and compactibility of asphalt concrete produced in half-warm mix asphalt technology with foamed bitumen. Constr. Build. Mater. 2016, 126, 108–118. [Google Scholar] [CrossRef] [Green Version]
- Ministry of Transport of the People’s Republic of China. JTG T55-2019-Technical Specifications for Highway Asphalt Pavements Recycling; Ministry of Transport of the People’s Republic of China: Beijing, China, 2019.
- Ren, P. Study on the Fretting Corrosion Behavior of Steels. Ph.D. Thesis, Southwest Jiaotong University, Xi’an, China, 2019. [Google Scholar]
- Ministry of Transport of the People’s Republic of China. JTG F40–2004-Technical Specification for Construction of Highway Asphalt Pavement; Ministry of Transport of the People’s Republic of China: Beijing, China, 2004.
- Li, N.; Tang, W.; Yu, X.; Zhan, H.; Ma, H.; Ding, G.Y. Investigation of moisture dissipation of water-foamed asphalt and its influence on the viscosity. Materials 2020, 13, 5235. [Google Scholar] [CrossRef]
- Ghabchi, R.; Singh, D.; Zaman, M. Evaluation of moisture susceptibility of asphalt mixes containing RAP and different types of aggregates and asphalt binders using the surface free energy method. Constr. Build. Mater. 2014, 73, 479–489. [Google Scholar] [CrossRef]
- Nahar, S.; Mohajeri, M.; Schmets, A.; Scarpas, A.; van de Ven, M.; Schitter, G. First observation of blending-zone morphology at interface of reclaimed asphalt binder and virgin bitumen. Transp. Res. Rec. 2013, 2370, 1–9. [Google Scholar] [CrossRef] [Green Version]
Figure 1.
Flowchart of preparing ER.
Figure 2.
Rotational viscosity of ER and CR.
Figure 3.
Combined gradations of reclaimed asphalt mixtures.
Figure 4.
Mixing torque tester.
Figure 5.
Torque values of asphalt mixtures at different mixing temperatures.
Figure 6.
Air void content of each studied mixture.
Figure 7.
Three indexes of different asphalt binders: (a) softening point; (b) penetration; (c) ductility.
Figure 7.
Three indexes of different asphalt binders: (a) softening point; (b) penetration; (c) ductility.
Figure 8.
The dynamic stability (DS) results of each studied mixture.
Figure 9.
The tensile strength ratio (TSR) results of each studied mixture.
Table 1.
Properties of CR used in this study.
| Properties | Test Results | Requirements (RA-25) | Specification Method |
|---|---|---|---|
| Viscosity, mm2/s (60 °C) | 2080 | 901~4500 | ASTM D2171 |
| Flash point, °C | 240 | >219 | ASTM D92 |
| Saturates, % (wt) | 22.3 | <30 | ASTM D2007 |
| Wt change, % (After TFOT, 163 °C) | 0.5 | <3 | ASTM D1754 |
| Specific gravity | 0.99 | Report | ASTM D70 |
Table 2.
Properties of emulsifier used in this study.
| Properties | Emulsifier A | Emulsifier B |
|---|---|---|
| Appearance | viscous liquid | yellow liquid |
| Electric charge | + | + |
| Blend stability | quick-set | quick-set |
| PH of aqueous solution | 10 | 11.3 |
| Amine value (mg/g) | - | 360–410 |
Table 3.
Gradations of extracted aggregates.
| RAP Size (mm) | Passing Percentage of Different Sieve Size/% | |||||||||
|---|---|---|---|---|---|---|---|---|---|---|
| 16 | 13.2 | 9.5 | 4.75 | 2.36 | 1.18 | 0.6 | 0.3 | 0.15 | 0.075 | |
| 10~16 | 100 | 89.3 | 32.8 | 10.5 | 9.1 | 7.6 | 6.4 | 4.8 | 3.9 | 3.4 |
| 5~10 | 100 | 100 | 91.2 | 18.6 | 11.0 | 8.8 | 7.5 | 6.2 | 5.4 | 4.8 |
| 0~5 | 100 | 100 | 100 | 90.9 | 62.4 | 41.0 | 29.6 | 19.6 | 15.8 | 13.7 |
Table 4.
Mix design results.
| RAP (%) | Virgin Mineral Materials (%) | AC (%) | Rejuvenator 1 (%) | |||
|---|---|---|---|---|---|---|
| 10~15 mm | 5~10 mm | 0~3 mm | Filler | |||
| 0 | 39.8 | 31.8 | 12.1 | 10.3 | 6.0 | 0 |
| 30 | 34.0 | 18.0 | 4.3 | 8.8 | 6.0 | 4/6.67 |
| 50 | 30.1 | 8.3 | 0 | 7.3 | 6.0 | 4/6.67 |
1 Rejuvenator: 4% and 6.67% was the content of control rejuvenator and emulsified rejuvenator by weight of aged asphalt, respectively.
Publisher’s Note: MDPI stays neutral with regard to jurisdictional claims in published maps and institutional affiliations. |
© 2021 by the authors. Licensee MDPI, Basel, Switzerland. This article is an open access article distributed under the terms and conditions of the Creative Commons Attribution (CC BY) license (https://creativecommons.org/licenses/by/4.0/).
Share and Cite
MDPI and ACS Style
Tang, W.; Yu, X.; Li, N.; Dong, F.; Wang, Z.; Zhang, Y. Effect of Rejuvenators on the Workability and Performances of Reclaimed Asphalt Mixtures. Materials 2021, 14, 6385. https://doi.org/10.3390/ma14216385
AMA Style
Tang W, Yu X, Li N, Dong F, Wang Z, Zhang Y. Effect of Rejuvenators on the Workability and Performances of Reclaimed Asphalt Mixtures. Materials. 2021; 14(21):6385. https://doi.org/10.3390/ma14216385
Chicago/Turabian StyleTang, Wei, Xin Yu, Ning Li, Fuqiang Dong, Zhongyuan Wang, and Yu Zhang. 2021. "Effect of Rejuvenators on the Workability and Performances of Reclaimed Asphalt Mixtures" Materials 14, no. 21: 6385. https://doi.org/10.3390/ma14216385
APA StyleTang, W., Yu, X., Li, N., Dong, F., Wang, Z., & Zhang, Y. (2021). Effect of Rejuvenators on the Workability and Performances of Reclaimed Asphalt Mixtures. Materials, 14(21), 6385. https://doi.org/10.3390/ma14216385
Note that from the first issue of 2016, this journal uses article numbers instead of page numbers. See further details here.
