Studies on the Microstructural Evolution and Mechanical Properties of Superalloy Inconel 718 Induced by Low Plasticity Burnishing Coupled with Turning
Abstract
:1. Introduction
2. Experiments
2.1. Material
2.2. LPB Process and Tensile Test
2.3. Measurements
3. Results
3.1. Analysis of Microstructural Characteristics
3.1.1. Misorientation Distribution
3.1.2. Misorientation Distribution
3.2. Micro-hardness
3.3. Residual Stress
3.4. Plastic Strain
3.5. Tensile Properties
3.6. Strengthening Mechanism Induced by the LPB Process
4. Conclusions
- (1)
- After the LPB process, the average grain diameter decreased from 4.43 to 4.09 μm, and the fraction of LAGBs decreased from 54.9 to 47.5%. The grain refinement phenomenon could be attributed to the increase of KAM and the formation of HAGBs.
- (2)
- The peak compressive stress was increased by a factor of 4.2 after the LPB process. The LPB process produced higher plastic strain (22.63%) at the surface, which indicated that a larger amount of plastic deformation was generated during the LPB process.
- (3)
- The LPB process induced higher values of the yield strength and the ultimate tensile strength. The enhanced yield strength depended on the average spacing between all boundaries and the HAGBs.
Author Contributions
Funding
Institutional Review Board Statement
Informed Consent Statement
Data Availability Statement
Conflicts of Interest
References
- Hua, Y.; Liu, Z. Effects of cutting parameters and tool nose radius on surface roughness and work hardening during dry turning Inconel 718. Int. J. Adv. Manuf. Technol. 2018, 96, 2421–2430. [Google Scholar] [CrossRef]
- Elsheikh, A.H.; Muthuramalingam, T.; Shanmugan, S.; Ibrahim, A.M.M.; Ramesh, B.; Khoshaim, A.B.; Moustafa, E.B.; Bedairi, B.; Panchal, H.; Sathyamurthy, R. Fine-tuned artificial intelligence model using pigeon optimizer for prediction of residual stresses during turning of Inconel 718. J. Mater. Res. Technol. 2021, 15, 3622–3634. [Google Scholar] [CrossRef]
- Suárez, A.; Veiga, F.; de Lacalle, L.L.; Polvorosa, R.; Wretland, A. An investigation of cutting forces and tool wear in turning of Haynes 282. J. Manuf. Process. 2018, 37, 529–540. [Google Scholar] [CrossRef]
- Alsoruji, G.; Muthuramalingam, T.; Moustafa, E.B.; Elsheikh, A. Investigation and TGRA based optimization of laser beam drilling process during machining of Nickel Inconel 718 alloy. J. Mater. Res. Technol. 2022, 18, 720–730. [Google Scholar] [CrossRef]
- Thakur, A.; Gangopadhyay, S. State-of-the-art in surface integrity in machining of nickel-based super alloys. Int. J. Mach. Tools Manuf. 2016, 100, 25–54. [Google Scholar] [CrossRef]
- Zhou, S.; Xu, T.; Hu, C.; Wu, H.; Liu, H.; Ma, X. Utilizing carbon nanotubes in ceramic particle reinforced MMC coatings deposited by laser cladding with Inconel 625 wire. J. Mater. Res. Technol. 2021, 13, 2026–2042. [Google Scholar] [CrossRef]
- Xu, J.; Lane, C.D.; Ou, J.; Cockcroft, S.L.; Maijer, D.M.; Akhtar, A.; Marciano, Y. Diffusion of nitrogen in solid titanium at elevated temperature and the influence on the microstructure. J. Mater. Res. Technol. 2021, 12, 125–137. [Google Scholar] [CrossRef]
- Nagarajan, B.; Kumar, D.; Fan, Z.; Castagne, S. Effect of deep cold rolling on mechanical properties and microstructure of nickel-based superalloys. Mater. Sci. Eng. A 2018, 728, 196–207. [Google Scholar] [CrossRef]
- Slavov, S.; Dimitrov, D.; Konsulova-Bakalova, M.; Vasileva, D. Impact of Ball Burnished Regular Reliefs on Fatigue Life of AISI 304 and 316L Austenitic Stainless Steels. Materials 2021, 14, 2529. [Google Scholar] [CrossRef]
- McClung, R.C. A literature survey on the stability and significance of residua stresses during fatigue. Fatigue Fract. Eng. Mater. Struct. 2007, 30, 173–205. [Google Scholar] [CrossRef]
- Avilés, R.; Albizuri, J.; Rodríguez, A.; de Lacalle, L.L. Influence of low-plasticity ball burnishing on the high-cycle fatigue strength of medium carbon AISI 1045 steel. Int. J. Fatigue 2013, 55, 230–244. [Google Scholar] [CrossRef]
- Gill, A.; Telang, A.; Mannava, S.R.; Qian, D.; Pyoun, Y.-S.; Soyama, H.; Vasudevan, V.K. Comparison of mechanisms of advanced mechanical surface treatments in nickel-based superalloy. Mater. Sci. Eng. A 2013, 576, 346–355. [Google Scholar] [CrossRef]
- Hua, Y.; Liu, Z.; Wang, B.; Hou, X. Surface modification through combination of finish turning with low plasticity burnishing and its effect on fatigue performance for Inconel 718. Surf. Coat. Technol. 2019, 375, 508–517. [Google Scholar] [CrossRef]
- Kluz, R.; Antosz, K.; Trzepieciński, T.; Bucior, M. Modelling the Influence of Slide Burnishing Parameters on the Surface Roughness of Shafts Made of 42CrMo4 Heat-Treatable Steel. Materials 2021, 14, 1175. [Google Scholar] [CrossRef] [PubMed]
- Raaj, R.K.; Anirudh, P.V.; Karunakaran, C.; Kannan, C.; Jahagirdar, A.; Joshi, S.; Balan, A. Exploring grinding and burnishing as surface post-treatment options for electron beam additive manufactured Alloy 718. Surf. Coat. Technol. 2020, 397, 126063. [Google Scholar] [CrossRef]
- Miranda, J.A.S.; Cristobal, A.T.; González-Barrio, H.; Fernández-Lucio, P.; Gómez-Escudero, G.; Madariaga, A.; Arrazola, P.J. Comparative study of finishing techniques for age-hardened Inconel 718 alloy. J. Mater. Res. Technol. 2021, 15, 5623–5634. [Google Scholar] [CrossRef]
- Okada, M.; Terada, S.; Miura, T.; Iwai, Y.; Takazawa, T.; Kataoka, Y.; Kihara, T.; Otsu, M. Fundamental burnishing characteristics of Ni-based alloy using coated carbide tool. Procedia Manuf. 2018, 15, 1278–1283. [Google Scholar] [CrossRef]
- Pu, Z.; Song, G.L.; Yang, S.; Outeiro, J.C.; Dillon, O.W., Jr.; Puleo, D.A.; Jawahir, I.S. Grain refined and basal textured surface produced by burnishing for improved corrosion performance of AZ31B Mg Alloy. Corros. Sci. 2012, 57, 192–201. [Google Scholar] [CrossRef]
- Grzesik, W.; Żak, K. Producing high quality hardened parts using sequential hard turning and ball burnishing operations. Precis. Eng. 2013, 37, 849–855. [Google Scholar] [CrossRef]
- Delgado, P.; Cuesta, I.; Alegre, J.M.; Díaz, A. State of the art of Deep Rolling. Precis. Eng. 2016, 46, 1–10. [Google Scholar] [CrossRef]
- Egea, A.S.; Rodriguez, A.; Celentano, D.; Calleja, A.; de Lacalle, L.L. Joining metrics enhancement when combining FSW and ball-burnishing in a 2050 aluminum alloy. Surf. Coat. Technol. 2019, 367, 327–335. [Google Scholar] [CrossRef] [Green Version]
- Lim, A.; Castagne, S.; Wong, C.C. Effect of Deep Cold Rolling on Residual Stress Distributions Between the Treated and Untreated Regions on Ti–6Al–4V Alloy. J. Manuf. Sci. Eng. 2016, 138, 111005. [Google Scholar] [CrossRef]
- Revankar, G.D.; Shetty, R.; Rao, S.S.; Gaitonde, V.N. Wear resistance enhancement of titanium alloy (Ti–6Al–4V) by ball burnishing process. J. Mater. Res. Technol. 2017, 6, 13–32. [Google Scholar] [CrossRef] [Green Version]
- Attabi, S.; Himour, A.; Laouar, L.; Motallebzadeh, A. Mechanical and wear behaviors of 316L stainless steel after ball burnishing treatment. J. Mater. Res. Technol. 2021, 15, 3255–3267. [Google Scholar] [CrossRef]
- Kumar, D.; Idapalapati, S.; Wei, W. Microstructural Response and Strain Hardening in Deep Cold Rolled Nickel-based Superalloy for Aerospace Application. Procedia CIRP 2018, 71, 374–379. [Google Scholar] [CrossRef]
- E8/E8M-15a; ASTM Standard Test Methods for Tension Testing of Metallic Materials. ASTM International: West Conshohocken, PA, USA, 2015.
- Hua, Y.; Liu, Z. Effects of Machining Induced Residual Shear and Normal Stresses on Fatigue Life and Stress Intensity Factor of Inconel 718. Appl. Sci. 2019, 9, 4750. [Google Scholar] [CrossRef] [Green Version]
- Lemarquis, L.; Giroux, P.; Maskrot, H.; Barkia, B.; Hercher, O.; Castany, P. Cold-rolling effects on the microstructure properties of 316L stainless steel parts produced by Laser Powder Bed Fusion (LPBF). J. Mater. Res. Technol. 2021, 15, 4725–4736. [Google Scholar] [CrossRef]
- Dehmas, M.; Lacaze, J.; Niang, A.; Viguier, B. TEM Study of High-Temperature Precipitation of Delta Phase in Inconel 718 Alloy. Adv. Mater. Sci. Eng. 2011, 2011, 940634. [Google Scholar] [CrossRef] [Green Version]
- Hua, Y.; Liu, Z. Experimental Investigation of Principal Residual Stress and Fatigue Performance for Turned Nickel-Based Superalloy Inconel 718. Materials 2018, 11, 879. [Google Scholar] [CrossRef] [Green Version]
- Seita, M.; Volpi, M.; Patala, S.; McCue, I.; ASchuh, C.; Diamanti, M.V.; Erlebacher, J.; Demkowicz, M.J. A high-throughput technique for determining grain boundary character non-destructively in microstructures with through-thickness grains. Npj Comput. Mater. 2016, 2, 16016. [Google Scholar] [CrossRef]
- Chamanfar, A.; Monajati, H.; Rosenbaum, A.; Jahazi, M.; Bonakdar, A.; Morin, E. Microstructure and mechanical properties of surface and subsurface layers in broached and shot-peened Inconel-718 gas turbine disc fir-trees. Mater. Charact. 2017, 132, 53–68. [Google Scholar] [CrossRef]
- Chen, L.; Ren, X.; Zhou, W.; Tong, Z.; Adu-Gyamfi, S.; Ye, Y.; Ren, Y. Evolution of microstructure and grain refinement mechanism of pure nickel induced by laser shock peening. Mater. Sci. Eng. A 2018, 728, 20–29. [Google Scholar] [CrossRef]
- Sitarama Raju, K.; Ghanashyam Krishna, M.; Padmanabhan, K.A.; Subramanya Sarma, V.; Gurao, N.P.; Wilde, G. Microstructure evolution and hardness variation during annealing of equal channel angular pressed ultra-fine grained nickel subjected to 12 passes. J. Mater. Sci. 2011, 46, 2662–2671. [Google Scholar] [CrossRef]
- Wu, D.; Yao, C.; Zhang, D. Surface characterization and fatigue evaluation in GH4169 superalloy: Comparing results after finish turning; shot peening and surface polishing treatments. Int. J. Fatigue 2018, 113, 222–235. [Google Scholar] [CrossRef]
- Klotz, T.; Delbergue, D.; Bocher, P.; Lévesque, M.; Brochu, M. Surface characteristics and fatigue behavior of shot peened Inconel 718. Int. J. Fatigue 2018, 110, 10–21. [Google Scholar] [CrossRef]
- Prevéy, P.S. The measurement of subsurface residual stress and cold work distributions in nickel base alloys. In Proceedings of the ASM’s Conference on Residual Stress in Design, Process and Materials Selection, Cincinnati, OH, USA, 27–29 April 1987; pp. 11–19. [Google Scholar]
- Kattoura, M.; Telang, A.; Mannava, S.R.; Qian, D.; Vasudevan, V.K. Effect of Ultrasonic Nanocrystal Surface Modification on residual stress, microstructure and fatigue behavior of ATI 718Plus alloy. Mater. Sci. Eng. A 2018, 711, 364–377. [Google Scholar] [CrossRef]
- Kattoura, M.; Mannava, S.R.; Qian, D.; Vasudevan, V. Effect of laser shock peening on residual stress, microstructure and fatigue behavior of ATI 718Plus alloy. Int. J. Fatigue 2017, 102, 121–134. [Google Scholar] [CrossRef]
- Luo, Z.; Zhang, H.; Hansen, N.; Lu, K. Quantification of the microstructures of high purity nickel subjected to dynamic plastic deformation. Acta Mater. 2012, 60, 1322–1333. [Google Scholar] [CrossRef]
- Kamikawa, N.; Huang, X.; Tsuji, N.; Hansen, N. Strengthening mechanisms in nanostructured high-purity aluminium deformed to high strain and annealed. Acta Mater. 2009, 57, 4198–4208. [Google Scholar] [CrossRef]
Ni | Cr | Mn | Nb | Mo | Ti | Al | Cu | Si |
---|---|---|---|---|---|---|---|---|
53.51 | 18.05 | 0.062 | 5.43 | 2.98 | 1.02 | 0.5 | 0.035 | 0.074 |
C | Co | P | Ta | B | Ca | N | Mg | Fe |
0.025 | 0.31 | 0.01 | 0.0085 | 0.0042 | 0.0032 | 0.0079 | 0.0014 | Bal |
Wavelength | Tube Target | Diffraction Plane | Bragg Angle (2θ) |
---|---|---|---|
Kβ (λ = 2.085 Å) | Cr | {311} | 150.89° |
Tube voltage | Tube current | X-ray slit | Exposure time |
30 kV | 1 mA | 2 mm | 90 s |
Publisher’s Note: MDPI stays neutral with regard to jurisdictional claims in published maps and institutional affiliations. |
© 2022 by the authors. Licensee MDPI, Basel, Switzerland. This article is an open access article distributed under the terms and conditions of the Creative Commons Attribution (CC BY) license (https://creativecommons.org/licenses/by/4.0/).
Share and Cite
Hua, Y.; Liu, Z.; Yi, J.; Tang, A. Studies on the Microstructural Evolution and Mechanical Properties of Superalloy Inconel 718 Induced by Low Plasticity Burnishing Coupled with Turning. Materials 2022, 15, 3740. https://doi.org/10.3390/ma15113740
Hua Y, Liu Z, Yi J, Tang A. Studies on the Microstructural Evolution and Mechanical Properties of Superalloy Inconel 718 Induced by Low Plasticity Burnishing Coupled with Turning. Materials. 2022; 15(11):3740. https://doi.org/10.3390/ma15113740
Chicago/Turabian StyleHua, Yang, Zhanqiang Liu, Jie Yi, and Aijun Tang. 2022. "Studies on the Microstructural Evolution and Mechanical Properties of Superalloy Inconel 718 Induced by Low Plasticity Burnishing Coupled with Turning" Materials 15, no. 11: 3740. https://doi.org/10.3390/ma15113740