Next Article in Journal
Pore Structure and Deformation Correlation of an Aluminum Foam Sandwich Subject to Three-Point Bending
Next Article in Special Issue
Optimization of Vertical Fixed-Bed Pyrolysis for Enhanced Biochar Production from Diverse Agricultural Residues
Previous Article in Journal
Modeling of the Flow Field and Clad Geometry of a Molten Pool during Laser Cladding of CoCrCuFeNi High-Entropy Alloys
Previous Article in Special Issue
Optimization of Pore Characteristics of Graphite-Based Anode for Li-Ion Batteries by Control of the Particle Size Distribution
 
 
Font Type:
Arial Georgia Verdana
Font Size:
Aa Aa Aa
Line Spacing:
Column Width:
Background:
Review

Renewable Carbonaceous Materials from Biomass in Catalytic Processes: A Review

by
Juan J. Villora-Picó
1,
Judith González-Arias
1,*,
Francisco M. Baena-Moreno
2,* and
Tomás R. Reina
1
1
Inorganic Chemistry Department and Materials Sciences Institute, University of Seville-CSIC, 41092 Seville, Spain
2
Chemical and Environmental Engineering Department, Technical School of Engineering, University of Seville, C/Camino de los Descubrimientos s/n, 41092 Sevilla, Spain
*
Authors to whom correspondence should be addressed.
Materials 2024, 17(3), 565; https://doi.org/10.3390/ma17030565
Submission received: 27 December 2023 / Revised: 16 January 2024 / Accepted: 23 January 2024 / Published: 25 January 2024
(This article belongs to the Special Issue Green Materials and Manufacturing Processes (2nd Edition))

Abstract

:
This review paper delves into the diverse ways in which carbonaceous resources, sourced from renewable and sustainable origins, can be used in catalytic processes. Renewable carbonaceous materials that come from biomass-derived and waste feedstocks are key to developing more sustainable processes by replacing traditional carbon-based materials. By examining the potential of these renewable carbonaceous materials, this review aims to shed light on their significance in fostering environmentally conscious and sustainable practices within the realm of catalysis. The more important applications identified are biofuel production, tar removal, chemical production, photocatalytic systems, microbial fuel cell electrodes, and oxidation applications. Regarding biofuel production, biochar-supported catalysts have proved to be able to achieve biodiesel production with yields exceeding 70%. Furthermore, hydrochars and activated carbons derived from diverse biomass sources have demonstrated significant tar removal efficiency. For instance, rice husk char exhibited an increased BET surface area from 2.2 m2/g to 141 m2/g after pyrolysis at 600 °C, showcasing its effectiveness in adsorbing phenol and light aromatic hydrocarbons. Concerning chemical production and the oxidation of alcohols, the influence of biochar quantity and pre-calcination temperature on catalytic performance has been proven, achieving selectivity toward benzaldehyde exceeding 70%.

1. Introduction

During the last decades, the demand for carbon-based materials has intensified [1] due to the need for many economies to be developed. The highest share of carbon-based materials comes from non-renewable and traditional fossil carbon [2]. At this pace, this fact will cause not only a lack of carbonaceous materials but also serious environmental challenges. As the need for sustainable practices increases in society, the use of renewable carbonaceous materials is key. The inherent properties of renewable carbonaceous materials, such as low footprint and diverse chemical functionalities, make them uniquely suited for replacing traditional carbon-based materials [3]. Furthermore, the use of renewable carbonaceous materials aligns with the principles of green chemistry, emphasizing the design of processes that minimize environmental impact while maximizing efficiency.
Within the many potential applications for renewable carbonaceous materials, its integration into catalytic processes has emerged as a compelling solution with far-reaching implications [4,5]. Catalysis, as a pivotal technology in the chemical industry, offers a unique opportunity to address the pressing need for cleaner and more sustainable methodologies. The escalating depletion of finite fossil fuel resources and the associated environmental impacts of traditional catalytic processes underscore the urgency of transitioning toward renewable alternatives. By incorporating renewable carbonaceous materials derived from biomass, agricultural residues, and other sustainable sources into catalytic processes, our society can achieve a double aim. It can not only mitigate the environmental footprint associated with catalytic processes but also contribute to the development of a circular and sustainable economy.
There are some previous works dealing with the application of renewable carbon materials in catalytic processes. Some examples of these works are explained next. Biochar stands out as a highly promising catalyst and support for the process of biomass gasification. In the pursuit of efficient hydrogen production from biomass steam gasification, both biochar and Ni-based biochar were investigated. As a point of reference, commercial activated carbon was also included in this study for comparative analysis [6]. The investigation delved into the impact of various parameters such as gasification temperature, steam-to-biomass ratio, Ni loading, and biochar properties on the catalyst’s activity, specifically in terms of hydrogen production. Notably, the Ni/AC catalyst demonstrated superior performance at a gasification temperature of 800 °C, a steam-to-biomass ratio of 4, and a Ni loading of 15 wt.% [6]. Among the various tested catalysts, it was observed that Ni supported on cotton char exhibited the highest activity in hydrogen production, achieving a remarkable 64.02 vol.% and 92.08 mg/g biomass.
Another promising strategy for optimizing the utilization of oxygen within biomass resources is utilizing biomass catalytic pyrolysis products to derive valuable oxygen-containing chemicals [7]. The catalyst, playing a pivotal role in this process, needs to exhibit characteristics such as environmental friendliness, cost-effectiveness, high activity, and stability. In this line, a study conducted by Chen et al. introduced an innovative and environmentally sustainable method for producing phenols from bamboo waste via catalytic pyrolysis, employing N-doped biochar as the catalyst [7]. The investigation, conducted in a fixed bed reactor, aimed to unravel the catalytic pyrolysis mechanism facilitated by the N-doped biochar catalyst. The results underscored the significant enhancement of phenol generation, reaching an impressive 82% [7].
Biochar was also proposed as a key element to develop a catalyst for efficient production of biodiesel. Two solid acid catalysts based on carbon were synthesized by sulfonating pyrolysis char in two different ways, representing a total of four catalysts to be tested. The catalysts underwent comprehensive evaluation for their efficacy in catalyzing both the transesterification of vegetable oils and the esterification of free fatty acids. The comparison of the four resulting catalysts revealed that the catalyst with the highest surface area and acid density exhibited superior catalytic activity, particularly in the production of biodiesel from canola oil in the presence of methanol as the reagent. Additionally, the catalyst with a higher surface area demonstrated enhanced transesterification activity compared with catalysts with similar acid densities [8].
However, the works described are standalone studies dedicated to a reduced scope.
To close this information gap, this paper analyzes the main applications of carbonaceous materials in catalytic processes, as well as the innovative studies carried out so far by experts in this area. The main applications envisaged are biofuel production, tar removal, chemical production, photocatalytic systems, microbial fuel cell electrodes, and oxidation applications. This work is organized as follows. First, the production of the main renewable carbonaceous materials is explained, including the sources that they could come from and their properties. Later on, the different applications for catalytic processes identified are described in depth, including works carried out at different lab scales. We finalize the paper by concluding the main aspects of each application and the potential of renewable carbonaceous materials to transform catalytic processes into more sustainable activities.

2. Renewable Carbonaceous Materials from Biomass Production and Its Properties

Biomass, a sustainable and renewable material rich in carbon and primarily consisting of hemicellulose, cellulose, and lignin, has been commonly used as a raw material for crafting diverse high-value carbon-based products, including carbon materials, chemicals, and biofuels. Lignocellulosic biomass can typically be categorized into three primary components: cellulose, hemicellulose, and lignin [9]. Lignin-rich biomass is the most plentiful renewable carbon resource on Earth, second only to cellulose, boasting a global production of 40–50 million tons annually [10]. Given the high carbon content of lignin, lignocellulosic biomass emerges as a promising choice for use as a precursor in the production of valuable carbonaceous materials.
Currently, there is considerable focus on utilizing biomass as a cost-effective and environmentally friendly carbon source for generating valuable carbonaceous materials with different applications [11]. These high-value carbonaceous materials are primarily composed of pure carbon. In contrast, biomass contains not only carbon but also significant amounts of hydrogen, oxygen, nitrogen, and sulfur. Consequently, the essential steps for producing these materials from biomass involve breaking chemical bonds and eliminating hydrogen, oxygen, nitrogen, and sulfur, while preserving the carbon content.
Biomass conversion to valuable carbonaceous materials is mainly accomplished through various methods, including biological, chemical, and thermochemical processes. In general, thermochemical processes are favored for their shorter processing time, resulting in increased product yields [12]. Unlike biochemical processes that demand specific feedstock, thermochemical processes enable the utilization of the entire biomass to generate value-added materials [13]. Although thermochemical processing is the most used method to obtain carbonaceous materials from biomass waste since a carbonization step is required, it is worth noting that other alternatives are also used. Among them, chemical treatments such as the green activation method are also highlighted. In this case, the properties of a pre-carbonized product are improved using chemical activation [14]. While chemical activation is a widely used and effective technique for obtaining carbonaceous materials with desirable porous structures and high surface area, its broader application is hindered by drawbacks such as low yield and the need for substantial amounts of harmful activators and cleaning agents [14].
Among the different thermochemical processes for carbonaceous material production, pyrolysis, torrefaction, and hydrothermal carbonization (HTC) are highlighted [15]. During the thermochemical conversion, carbonization and graphitization of biomass take place regardless of the process. Below, a short overview of the most used processes for carbonaceous material production from biomass is shown.

2.1. Pyrolysis and Torrefaction

Pyrolysis and torrefaction of biomass involves breaking down polymer chains in biomass macromolecules through externally supplied heat under an inert atmosphere, resulting in the production of condensable volatiles (bio-oil), non-condensable gases, and a carbonaceous material commonly known as biochar. Torrefaction and pyrolysis are similar thermal processes employed in material conversion. Torrefaction operates within a lower temperature range (around 200–300 °C), while pyrolysis necessitates higher temperatures covering from 400 to 1000 °C. Notably, the differentiation between these processes primarily lies in the reaction temperature and the retention time of the material. Consequently, it is prevalent in the literature to encounter references to torrefaction as a form of slow- and mild-pyrolysis, emphasizing the shared characteristic of temperature-driven transformation while acknowledging the nuanced variations in their operational parameters [16,17]. The outcomes of these processes are influenced by the reaction conditions, with slow pyrolysis and torrefaction favoring low heating rates and long residence times for biochar production, while fast pyrolysis employs high heating rates and short residence times to predominantly generate bio-oil (up to 75%) [18]. The crude pyrolytic bio-oil can be further upgraded to advanced biofuels or bio-based chemicals. Numerous studies have explored biomass pyrolysis due to the potential of bio-oil and biochars [19,20,21]. Various pyrolysis techniques, such as co-pyrolysis, catalytic pyrolysis, microwave pyrolysis, and solar pyrolysis, have been developed to optimize and enhance pyrolysis processes for biomass conversion [22].
The composition of biomass plays a crucial role in shaping the outcomes of the pyrolysis/torrefaction process. As previously mentioned, biomass typically consists of cellulose, hemicellulose, and lignin, each contributing differently to the pyrolysis reactions [23]. Higher cellulose content in biomass has a notable effect on the pyrolysis process. It tends to accelerate the degradation of organic compounds during pyrolysis, leading to a faster release of volatile components. This acceleration results in an increased production of tar and gases. Therefore, biomass with a higher cellulose content tends to yield more tar and gases during pyrolysis. Conversely, lignin is a more intricate and resistant structure compared with cellulose, and its presence in biomass can slow down the pyrolysis process. The degradation of lignin requires more energy and time, contributing to a slower overall pyrolysis rate. Consequently, biomass with a high lignin content may yield lower amounts of tar and gases compared with biomass with higher cellulose content [24]. Furthermore, the type of biomass also has implications for the resulting char’s porosity. Different plant materials possess unique structural characteristics, and these variances influence the development of pores in the char produced during pyrolysis. For instance, research comparing char from various agriculture residues revealed that sugar cane bagasse and wood stem produced char with well-developed pores and high surface area, while others exhibited poor porosity development. This discrepancy in porosity has implications for the potential applications of the resulting char [25].
Additionally, the moisture content in biomass is a significant factor influencing the pyrolysis process. If the moisture content is high (above 30%), a considerable amount of the heat supplied during pyrolysis is utilized to remove moisture rather than facilitate the pyrolysis reactions. This situation slows down the heating rate, necessitating additional time to reach the target pyrolysis temperature. To optimize the pyrolysis process, especially for energy efficiency, it is advisable to use dry biomass or, if necessary, pre-dry the biomass to reduce moisture content before pyrolysis. This ensures that a larger portion of the heat is utilized for the intended thermochemical conversion, contributing to a more efficient and productive pyrolysis process [26].
Temperature, residence time, heating rate, and biomass particle size also play critical roles in shaping the formation of carbonaceous materials [27]. Higher temperatures during pyrolysis tend to reduce the yield of char but promote the devolatilization process, impacting the production of bio-oil and gases. Conversely, longer residence times and slower heating rates contribute to increased char yield, influencing the surface area and porosity of the resulting biochar [28,29].
Optimizing the pyrolysis process involves strategic considerations. Selecting dry biomass with a high lignin content is advisable, as it enhances energy efficiency during heating. Utilizing lower temperatures, slower heating rates, and longer residence times tends to maximize the overall yield of carbonaceous materials. However, it is noteworthy that higher temperatures and faster heating rates can enhance the porosity of carbonaceous materials, offering unique characteristics that may be desirable for certain applications [30].

2.2. Hydrothermal Carbonization

Unlike pyrolysis, HTC utilizes water as a solvent and reaction medium, allowing high-water-content biomass, eliminating the need for drying and reducing energy requirements [31]. However, hydrochars often exhibit low surface area and porosity, limiting their applications. The reaction mechanism involves hydrolysis, dehydration, decarboxylation, aromatization, and recondensation, with temperature influencing pathways. This process is primarily governed by hydrolysis [32]. In this step, hemicellulose, cellulose, and lignin undergo decomposition into smaller fragments, facilitating subsequent reactions like dehydration and decarboxylation. These reactions are crucial for reducing the H/C and O/C ratios, ultimately leading to the formation of a solid carbonaceous product. Further reactions, like decarboxylation, contribute to the degradation of carboxyl–carbonyl groups and the release of the main components of the final flue gas, primarily composed of CO2 and CO [32].
The characteristics of hydrochar produced through HTC are intricately influenced by the composition of the biomass, the specific type of biomass utilized, and the operating conditions employed during the HTC process [33]. The complex nature of lignin makes it less degradable, contributing to the overall mass of hydrochar produced during the HTC process [34].
The morphological changes in biomass during HTC are notably influenced by the temperature at which the process is conducted. Lower temperatures within the range of 150–200 °C are conducive to maximizing the production of solid hydrochar [33]. In contrast, higher temperatures lead to extensive dehydration, resulting in a reduction in hydrochar yield [35]. This temperature-dependent morphological alteration is crucial in determining the structure and properties of the resulting hydrochar. Furthermore, temperature not only affects yield but also influences the surface area of the hydrochar [36]. Higher temperatures during HTC tend to yield hydrochar with larger surface areas. This is a critical aspect as the surface area impacts the reactivity and applicability of hydrochar in various applications, such as soil amendments or electrochemical devices.
The residence time also plays a pivotal role. Longer residence times, especially at lower temperatures, enhance hydrochar yield. This prolonged exposure allows for more extensive carbonization and recondensation reactions, contributing to the overall yield and characteristics of the hydrochar [37].
It is worth noting that the HTC process itself is relatively slow, ranging from hours to days [38]. The slow kinetics of the process allow for careful control and manipulation of the reactions, contributing to the versatility of HTC as an approach for biomass conversion. The ability to tailor hydrochar characteristics by adjusting parameters such as temperature, residence time, and biomass composition makes HTC a versatile and adaptable method for transforming biomass into functionalized carbonaceous materials for different applications.
In contrast to carbonaceous materials produced via thermal pyrolysis, HTC materials feature furanic and aromatic units containing oxygen-substituted arene-type moieties. This characteristic opens up the potential for incorporating supplementary substances during the hydrothermal reaction or through post-functionalization, thereby allowing for the further adjustment of the physical and chemical attributes of HTC materials [39].
Until now, we have focused on the most used thermochemical processes to produce renewable carbonaceous materials. This is a key point to understand their potential for catalytic processes. Nonetheless, the readers could benefit from understanding where carbonaceous materials are used nowadays. Therefore, the next section presents a brief overview of their present applications before diving into the catalytic applications of renewable carbonaceous materials.

2.3. Overview of Applications for Carbonaceous Materials

After explaining the different thermochemical processes used in the production of renewable carbonaceous materials along with their respective properties, it is worth highlighting the present utilization of carbonaceous materials before moving to their potential catalytic applications. Indeed, carbonaceous materials are not new to our society. These materials have a long history in synthesis and applications and are integral to daily life. Examples include activated carbon for deodorization and water purification, graphite in pencils, carbon fibers for sports equipment, and carbon black in inks and pigments. The accidental discovery of synthetic graphite in the 19th century led to the development of various carbon materials like glass-like carbon and carbon fibers, widely applied in industry [40].
As shown above, biochar, the most well-established carbonaceous material derived from biomass, is produced via the thermochemical transformation of organic matter. Moreover, activated carbon and carbon fibers, both originating from biomass, have been formulated for diverse applications [41,42,43]. The exploration of innovative carbon-based nanomaterials, such as fullerene, carbon nanotubes, graphene, and graphene quantum dots, has significantly attracted interest in the creation of carbon nanostructures from carbonaceous materials derived from biomass [44]. In Table 1, we group a list of works dealing with different carbonaceous materials obtained from various biomass waste. This serves as a summary to show the wide variety of applications of these materials. Table 1 not only provides a comprehensive overview of different carbonaceous materials but also outlines the various applications they serve. The thermochemical processes involved in obtaining these materials are also presented in Table 1.

3. Applications of Carbonaceous Materials in Catalytic Processes

3.1. Biofuel Production

The escalating demand for energy resources, propelled by population expansion and economic advancement, necessitates the exploration of alternatives to existing fuels characterized by finite resources and environmental ramifications such as the greenhouse effect and climate change [66]. In light of these considerations, biofuels emerge as a viable alternative, with biodiesel standing out as the most widely consumed biofuel globally [67]. A predominant methodology for biodiesel production involves the transesterification of used cooking oil, wherein the oil undergoes a chemical reaction with methanol [68]. While homogeneous alkaline catalysts like KOH or carbonates are frequently employed, their limited recoverability prompts a quest for heterogeneous catalysts [69]. Catalysts encompass alkali metal hydroxides, metal oxides, or zeolites [70], yet an imperative focus remains on identifying economically favorable catalysts. Utilizing carbonaceous materials as supports, particularly biochar, is a judicious choice owing to their economic viability and apt chemical and textural characteristics. In this context, Azman et al. systematically synthesized nickel oxide (NiO) and molybdenum oxide (MoO) catalysts, employing a biochar derived from wood chips as a robust support matrix. The catalytic performance was assessed, revealing yields exceeding 70% at an operational temperature of 75 °C for the catalyst subjected to calcination at 400 °C (Figure 1). This experimental outcome underscores the catalytic efficacy of the prepared NiO and MoO catalysts, as supported on the designated biochar substrate, within the specified reaction conditions [71]. CaO commands significant attention due to its commendable catalytic activity, cost-effectiveness, and robust basicity. Di Bitonto et al. demonstrated the preparation of CaO catalysts supported on biochar derived from avocado seeds, yielding remarkable conversions of 91% [72]. The potential concern of CaO leaching into the reaction medium underscores the necessity for stability promoters, often rooted in mixed oxides such as SiO2 [73]. Nevertheless, certain biochars exhibit inherent catalytic activity, obviating the need for additional support materials. Daimary et al. conducted a study wherein biochars with elevated concentrations of alkali and alkaline earth metals, primarily potassium, were derived from potato skins. The catalytic outcomes indicated exceptional activity, with conversion values surpassing 97% [74]. Alkaline catalysts, however, are susceptible to saponification, complicating the separation of reaction products. An intriguing avenue involves the incorporation of –SO3H groups onto biochar surfaces, as these groups have demonstrated catalytic prowess in transesterification processes. Yadav et al. achieved yields exceeding 99% with excellent recyclability by subjecting biochars from bamboo and coconut husk to post-treatment with H2SO4 [75]. Analogous outcomes are observed with biochars sourced from olive pits, nut shells, microalgae, or discarded cork [67,76].
The Fischer–Tropsch synthesis (FTS) process constitutes a prominent method for the catalytic conversion of synthesis gas into hydrocarbons and oxygenated compounds, with a primary focus on optimizing yield for the production of light olefins suitable for use as fuels [77]. The most commonly used catalyst is Co and other metals used as promoters (Ru, Ni, and Fe) supported on metal oxides (e.g., Al2O3, TiO2, or SiO2) [78]. However, challenges arise with certain metals, notably Co, which can form irreducible compounds like CoAl2O4, leading to rapid catalyst deactivation. Biochars present an intriguing alternative owing to their favorable porous properties and elevated thermal stability. Yousefian et al. demonstrated the preparation of biochars derived from rice husk, coconut husk, and algae as supports for cobalt catalysts, showcasing the capacity of carbonaceous materials to enhance Co reducibility. The catalytic outcomes proved highly satisfactory, achieving a CO conversion rate of 67% [79]. Surface chemistry modifications on biochar significantly influence catalytic activity, as exemplified by Bai et al. who introduced nitrogen through urea doping. This alteration modified the electronic structure of the material, enhancing metal dispersion and metal–support interaction, resulting in conversion rates exceeding 90%, with selectivity toward heavier hydrocarbons reaching approximately 50% [80]. Exploring Fe as a catalyst is noteworthy due to its heightened selectivity toward olefins and its inherent water–gas shift activity, thereby augmenting hydrogen content in the feed. Teimouri et al. undertook the preparation of Fe catalysts on biochar derived from canola hulls, achieving a selectivity exceeding 72% toward C5+ products [81]. This diversification in catalyst materials and surface modifications on biochar underscores the dynamic nature of catalyst development within the FTS process, with ongoing efforts aimed at enhancing efficiency and selectivity.
Hydrogen, characterized by its high energy content and environmental friendliness, is regarded as a pivotal fuel in the paradigm of future energy sources [82,83]. Various processes can yield hydrogen, with dry reforming of methane emerging as a prominent industrial method. This reaction facilitates the conversion of two major greenhouse gases, CO2 and CH4, into H2. Carbon-based catalysts have garnered substantial attention due to their inherent stability and resistance to deactivation by sulfur compounds. In a study conducted by Zhao et al., catalysts derived from biochar sourced from hawthorn seeds exhibited exceptional performance following torrefaction treatment, achieving conversions surpassing 70% [84]. Despite the efficacy of existing methods, advancements have introduced novel approaches, such as the catalytic decomposition of methane. In this context, surface carboxylic groups on biochar act as catalysts for methane decomposition. However, the formation of carbonaceous deposits results in the rapid deactivation of the catalyst, necessitating comprehensive strategies to address this challenge [85]. This predicament underscores the ongoing efforts in the scientific community to innovate and refine processes, ensuring the sustained viability and efficiency of biochar-based catalysts in the production of hydrogen, a critical component of the envisioned clean energy landscape.
In Table 2, we summarized the various biomass-derived catalysts for biofuel synthesis.
In conclusion, the global demand for sustainable energy alternatives has fueled extensive research in biofuels, particularly biodiesel production. The use of carbonaceous materials, especially biochar, as catalyst supports has shown economic viability and technological promise. Future research should focus on optimizing biochar-supported catalyst synthesis processes and addressing stability concerns. In the FTS, biochar-supported catalysts offer improved reducibility and enhanced selectivity, showcasing dynamic developments in catalyst materials. Looking forward, hydrogen production through processes like dry reforming of methane using biochar-based catalysts is a key focus. Despite promising results, ongoing research is needed to overcome challenges such as catalyst deactivation and ensure sustained efficiency in the evolving landscape of clean energy production. As the scientific community continues to innovate, these findings contribute to the sustainable development of biochar-based catalysts, paving the way for a cleaner and more efficient energy future.

3.2. Tar Removal

Due to the growing interest in alternative energy sources caused by increased CO2 emissions and global climate concerns, biomass is seen as a renewable energy source, with gasification being a promising technology for biomass-to-energy conversion. Gasification, while effective, faces challenges, especially in tar removal. Two main groups of methods (i.e., in situ and downstream) aim to address tar issues [86,87]. The use of carbonaceous materials is proposed as a potential solution for downstream tar removal [88,89,90].
The adsorption capabilities of carbonaceous materials for contaminants are attributed to their distribution of porous structures, high specific surface areas, and enhanced surface chemistry properties. The effectiveness of adsorption also depends on factors like hydrophobicity, alkalinity, ion exchange capacity, and elemental composition. As an example, hydrochars prepared at low temperatures (e.g., 180 °C) without additional heat treatment and/or surface activation initially possess a limited pore structure. However, oxygen groups on the surface promote adsorption and enable further surface modification [91].
As already mentioned, the most important structural characteristic of the carbonaceous materials to be used as tar adsorbents is having a high surface area measured by the distribution of micropores, mesopores, and macropores. The chemical characteristics are determined by the presence of inorganics scattered on the surface and oxygen-containing functional groups at the borders of the graphite sheets. These oxygen sites enhance the adsorption of polar molecules, influencing the adsorption capacity and catalytic activity of the carbonaceous material [92,93].
Numerous studies have highlighted the effectiveness of carbonaceous materials obtained through thermal treatments in the removal of tars in industrial applications. For instance, research has demonstrated the enhanced adsorption capacity of activated carbons derived from wood waste in gasification systems. In pyrolysis processes, a significant reduction in tars has been observed using porous carbons derived from agricultural residues. Zhang et al. demonstrated the effectiveness of different carbonaceous-based materials for in situ tar reforming in their work. They observed a significant reduction in the tar yield when using the different materials, resulting in great tar removal rates ranging from ca. 20% to ca. 47% [94]. The results that they obtained can be graphically seen in Figure 2.
Similarly, activated carbons find extensive application in adsorption processes, aiding in the capture of organic volatile compounds and adsorbing hydrocarbons and PAHs [95,96,97]. Additionally, activated carbons are frequently employed in gas cleaning within combustion plants, effectively eliminating metals and dioxins at temperatures ranging from 150 to 200 °C [98].
Examples of different carbonaceous materials used as tar adsorbents can be found in the literature as shown below. Liu et al. assessed rice husk and corncob biochar adsorption of phenol. The results show a significant increase in adsorption capacities at phenol concentrations from 5000 to 8000 mg/L, with stability at concentrations exceeding 8000 mg/L. Biochar adsorption is influenced by both surface areas and total functional group contents, which is impacted by retention time during the two stages of pyrolysis and carbonization [99].
Phuphuakrat et al. introduced a two-step method for tar removal using decomposition and adsorption. Activated carbon demonstrated superior adsorption of light aromatic hydrocarbon tars and light PAH tars compared with wood chips and synthetic porous cordierite. Wood chips, however, proved practical by effectively minimizing condensable tar without compromising system efficiency, making it a noteworthy tar adsorbent [100].
Similarly, Paethanom et al. investigated the adsorption capabilities of rice husk char as a tar adsorbent, which exhibited a positive adsorption performance. Following thermal decomposition at elevated temperatures, the pores of the rice husk char were well developed, leading to an increased surface area. For example, raw rice husk had a low BET surface area of 2.2 m2/g, while the pyrolyzed char at 600 °C exhibited a higher BET surface area of 141 m2/g. Nonetheless, increasing the temperature led to a reduction in the BET surface area [101]. This can be observed in Figure 3, showing the great importance of pyrolysis temperature on the final adsorption capabilities of the carbonaceous materials.
Heavy tar components could condense at the bottom of the char bed, suggesting that tar removal using rice husk char involved both tar molecule adsorption in the char material’s pores and condensation of heavy tar molecules in the hot gas as it passed through the adsorption bed at ambient temperature. Although some char was soaked by the condensed heavy tar, the majority of the rice husk char remained dry after tar adsorption. Consequently, the char adsorbent is suitable for dry gas light tar adsorption, extending its service life. Effective adsorption of light aromatic hydrocarbon tars like xylene and styrene was also observed. However, subsequent poor adsorption performance and increased tar amounts were noted due to de-adsorbed tars surging out with the exit gas. Phenol removal was also notably successful in this work [101,102]. For large-scale applications, it is advised to assess the saturation point of biochar adsorbent under specific operating conditions before gas cleaning system design. Various methods, including thermal, extractive, and chemical regeneration processes, can be employed to treat or regenerate waste adsorbents in general [103,104].
In terms of tar conversion, carbonaceous materials are also a good option to consider. For example, El-Rub et al. showed a comparison of biomass char to various catalysts like dolomite and nickel during biomass gasification at a temperature range of 700–900 °C in their work. They used phenol and naphthalene as model tar compounds. Dolomite and nickel showed the highest phenol conversion at 90% and 91%, respectively. Their reforming capabilities were evident, producing H2 and CO. Biomass-derived char exhibited moderate phenol conversion (i.e., 82%) due to thermal cracking at high gasification temperatures. Despite a limited lifetime, continuous activation through gasification reactions enhances char stability. Nickel catalyst excelled in naphthalene removal, while the lower conversion of dolomite was linked to its low iron content. Biomass chars, excluding nickel, displayed high activity, offering stability and effectiveness compared with the sensitive nickel catalyst [105].
Additionally, Fuentes-Cano et al. explored the catalytic decomposition of two model tars (toluene and naphthalene) using three distinct carbonaceous materials (coconut char, coal char, and dried sewage sludge char). The primary mechanisms in tar conversion over carbonaceous material involve deposition, dehydrogenation (resulting in soot formation on the char surface), and soot gasification, mirroring the processes observed in tar conversion over porous particles [106].
The catalytic performance of char is influenced by various factors, including biomass resources, gasification/pyrolysis conditions, catalytic conditions, gasifier types, and tar composition. Klinghoffer et al. extensively discussed the use of residual char as a catalyst for tar conversion, emphasizing its dependence on gasification temperature and time. Char samples from gasification at 550 °C showed inadequate BET surface area due to high residual organics. However, increasing reaction time or temperature led to higher surface area chars, ranging from 429 to 687 m2/g [107].
In conclusion, the utilization of carbonaceous materials for tar removal and conversion presents a promising avenue for advancing sustainable energy production. The adsorption capabilities of these materials, attributed to their porous structures and surface chemistry properties, have been demonstrated in various studies to effectively address the challenges associated with tar removal. Future research endeavors could focus on optimizing the synthesis methods to enhance the structural characteristics, such as surface area and pore distribution, thereby improving adsorption capacities. Additionally, exploring innovative approaches for in situ tar reforming and investigating the long-term stability of carbonaceous materials in large-scale applications would contribute valuable insights. Furthermore, the catalytic potential of biomass-derived chars warrants further investigation, emphasizing the influence of various factors on their performance in tar conversion processes. By addressing these aspects, future research can contribute significantly to the development of efficient and sustainable biomass-to-energy conversion technologies.

3.3. Chemical Production

Biochar finds significant application in the synthesis of high-value compounds, serving both as a catalyst support and as a metal-free catalyst. One notable application is in the oxidation of alcohols, a crucial process in industries such as pharmaceuticals, petrochemicals, and plastics. Chen et al. undertook the preparation of carbon materials derived from dried grain residues obtained from distilleries, aiming to modify titanate nanofibers with supported gold nanoparticles. The study meticulously investigated the influence of biochar quantity and the temperature of pre-calcination treatments on the catalytic performance of the material. Furthermore, the incorporation of biochar demonstrated enhanced control over selectivity, particularly directing the reaction toward benzaldehyde, a challenging aspect in alcohol oxidation reactions (Figure 4) [108]. Catalytic oxidation of carbonyl compounds is equally pivotal in chemical and drug synthesis. Abedian-Dehaghani et al. employed biochars co-doped with selenium and nitrogen for aldehyde oxidation, achieving yields exceeding 90% [109]. Biochars also play a crucial role in diverse processes, including the oxidative dehydrogenation of N-heterocycles using air as an oxidant. Pang et al. successfully prepared biochars from wheat husk, attaining yields surpassing 90%. The high hydrophobicity of the biochar proved advantageous in facilitating the removal of produced water from active sites [110].
Hydrogenation reactions represent crucial processes in industrial applications, and biochars emerge as viable catalysts in such reactions. Longo et al. employed Pd catalysts supported by biochars for the hydrogenation of benzaldehyde to yield toluene. Utilizing diverse biochars sourced from both animal and plant biomass, the catalytic results demonstrated high efficacy, achieving total conversion within 2 h of reaction time and displaying selectivities exceeding 95%, accompanied by commendable recyclability [111]. The reduction of nitroarenes is another industrially significant reaction, serving as a primary route to produce anilines, crucial precursors for drugs or dyes [112]. In this regard, Kumar et al. developed a RuO2 catalyst supported by biochar derived from pine needles. The catalysts exhibited elevated conversion values attributed to the presence of nitrogen within the carbonaceous network, facilitating improved distribution and stability of Ru nanoparticles [113]. Sadjadi et al. synthesized Pt catalysts supported on biochar derived from a specific plant, achieving high conversion values exceeding 97%. However, due to complications in recovery, they incorporated Fe3O4 to confer magnetic properties, thereby enhancing recyclability [114]. Additionally, they prepared a biochar–halosite nanocomposite, serving as a support for Pd catalysts, yielding satisfactory conversion results [115]. The surface chemistry of biochars plays a pivotal role in the catalytic activity of the resultant materials, as surface groups have been identified to contribute to the stabilization of metal nanoparticles [116]. Ren et al. prepared biochars with a high nitrogen content from sewage sludge, demonstrating significant catalytic activity in the reduction of nitrophenols with a remarkable 90% conversion within a 4 min reaction time, coupled with robust recyclability. In this context, carbon atoms adjacent to nitrogen sites serve as crucial reaction sites [117]. Moreover, the presence of oxygen or nitrogen groups influences the hydrophilicity of the carbonaceous material, thereby enhancing chemical activity. This was explored by Wang et al., who investigated the impact of oxygenated groups in the hydrogenation of organic compounds (eugenol, vanillin, and nitrobenzene). The results revealed that nitrobenzene, lacking strong hydrogen bonds, was less affected by changes in polarity, while vanillin and eugenol demonstrated facilitated activation of the (C=O) and (C=C) groups, respectively [118].
The valorization of biomass for the production of high-value-added chemicals stands as a significant application of biochars. Wang et al. engineered a Ni-Mo2C catalyst supported on a graphitized biochar, derived from sawdust, for the hydrogenation of lignin. The incorporation of the metal catalyst into the biochar elevated the yield of liquid products to over 60%, demonstrating remarkable recyclability. This catalytic efficacy is attributed to the synergistic interaction between biochar and metal nanoparticles, facilitating efficient electron transfer [119]. In a parallel investigation, Zhang et al. focused on the microwave-assisted oxidation of biomass-derived glucose to produce gluconic acid (GUA) and glucuronic acid (GOA). Employing Cu catalysts supported by biochars, they achieved yields of 39.0% and 30.7% for GUA and GOA, respectively. These favorable catalytic outcomes are ascribed to the high percentage of Cu and Cu2O species, along with a substantial presence of oxygenated functionalities within the biochar matrix [120]. Catalytic hydrogenation of aldehydes holds significance as a stabilizing step in the conversion of bio-oils. Bardestani et al. explored the hydrogenation of furfural to obtain furfuryl alcohol (FA), a precursor for levulinic acid. Their study revealed conversions exceeding 50% and selectivities surpassing 90% by utilizing Ru supported on a somewhat oxidized biochar, which serves to stabilize the Ru nanoparticles [121]. Fuente-Hernandez et al. synthesized Pt catalysts supported on biochar derived from maple biomass. The results exhibited conversions up to 50% at 210 °C, with a selectivity of over 80% toward the desired product (Figure 5) [122].
In conclusion, biochar serves as a versatile catalyst and support, with notable applications in alcohol oxidation, aldehyde oxidation, and hydrogenation reactions. The incorporation of biochar in these processes enhances selectivity and catalytic efficiency. Future research could focus on optimizing biochar synthesis for specific surface functionalities and exploring sustainable recovery methods for catalysts. The valorization of biomass using biochar-supported catalysts for high-value chemicals, such as lignin hydrogenation and glucose oxidation, demonstrates the potential of biochar in sustainable chemical production. Further exploration in stabilizing steps, like the hydrogenation of furfural, presents opportunities for advancement. As the field progresses, a deeper understanding of biochar–catalyst interactions will contribute to the sustainable development of biochar-based processes for high-value chemical synthesis.

3.4. Photocatalytic Systems

The discipline of photocatalysis is centered on the advancement of chemical reactions facilitated by the presence of light and a photocatalyst, which, in turn, augments the reaction rate under light conditions [123]. A prominent application within the realm of photocatalysis is the remediation of pollutants from wastewater, encompassing both organic [124] and inorganic pollutants [125]. Titanium dioxide (TiO2) stands out as the catalyst of choice due to its widespread usage, attributed to its cost-effectiveness, facile synthesis, and robust stability. However, a prominent challenge in its application lies in the substantial bandgap (3.2 eV), restricting its responsiveness solely to ultraviolet light [126]. Additionally, TiO2 presents an additional impediment concerning the swift recombination of charge carriers, thereby impeding radical formation [127]. Nevertheless, research has demonstrated that the incorporation of support alongside TiO2 can yield advantageous outcomes. Recent investigations have particularly highlighted the intriguing potential of utilizing biochars as a supporting material, considering economic, environmental, and photocatalytic perspectives. Notably, the deployment of TiO2–biochar composites has been observed in multiple studies to impede electron–hole recombination, thereby substantially enhancing the catalytic activity of the composite material [128].
Moreover, the utilization of this material category facilitates a reduction in the bandgap of the photocatalyst, enabling enhanced utilization of visible radiation, as substantiated by the findings of Wang et al. in their investigation of ammonium removal from aqueous solutions. Their study demonstrated satisfactory outcomes achieved under simulated sunlight conditions [129]. The choice of biochar is a critical determinant in the photocatalytic performance of the materials, encompassing both physical attributes such as BET surface area, porosity, and conductivity, as well as chemical characteristics. Hou et al. undertook the preparation of TiO2–biochar catalysts employing two distinct biochar types: one characterized by a significant number of surface groups and another with a more limited abundance. Their assessment of catalytic efficacy in the removal of Cr(VI) from wastewater revealed that the biochar with an increased number of surface groups exhibited a proclivity for Cr(VI) adsorption and engendered a higher concentration of radicals under light exposure, thereby affecting a substantial enhancement in catalytic activity. Importantly, this study demonstrated the capability of the biochar sample with heightened surface groups to sequester electrons, thereby sustaining catalytic activity even subsequent to the cessation of the light source [130]. Similarly, Wang et al. prepare biochar/TiO2 composites using bamboo powder as a carbon source. The synergistic effects of carbon doping with TiO2 are investigated under visible and UV light (Figure 6). A decreasing effect of surface area is observed as the particle size increases. The variation in these parameters significantly influences the catalytic activity [131].
Nonetheless, analogous outcomes were replicated with alternative catalysts such as Cu2O or Bi2WO6 [132]. The adoption of single-phase photocatalysts is frequently constrained by their suboptimal responsiveness to visible light and a rapid recombination rate of electron–hole pairs, culminating in diminished catalytic activity [133]. The collaborative interplay between biochar and such photocatalysts, akin to TiO2, culminates in the fine-tuning of the bandgap, thereby enhancing their sensitivity to visible light and optimizing the utilization of photoinduced carriers [132]. An unconventional alternative to conventional semiconductors is graphitic carbon nitride (g-C3N4), prized for its cost-effectiveness. However, the expeditious recombination of electron–hole pairs and feeble responsiveness to visible light curtail its practical application. Nevertheless, the incorporation of g-C3N4 onto a biochar substrate affords a π-conjugated structure, thereby modulating charge separation efficiency, refining the optical properties of g-C3N4, and augmenting the specific surface area. This augmentation is exemplified by Meng et al.’s work, wherein the combination demonstrated notable efficacy in the degradation of rhodamine and methyl orange from water [134]. Indeed, the incorporation of K into g-C3N4 manifests an enhancement in its photocatalytic efficacy under visible light irradiation. This improvement is attributed not only to the alteration in its electronic structure but also to the heightened adsorption capacity resulting from the dopant introduction. Empirical validation of this phenomenon has been substantiated by Li et al. in the context of naphthalene removal (Figure 7) [135]. Furthermore, certain biochars manifest inherent photocatalytic activity in the absence of supplementary materials. This is particularly pertinent for biochars endowed with a profusion of oxygenated groups, behaving akin to semiconductors wherein electrons within defect zones (valence band) are stimulated by visible light, traversing toward oxygenated groups (conduction band). This transfer of electrons to dissolved oxygen induces the generation of -OH radicals, as elucidated in the research by Xiao et al. [136].
Furthermore, photocatalysis finds diverse applications in processes related to the conversion of carbon dioxide (CO2) into fuels or higher-value compounds [137,138], as well as in the environmentally clean generation of hydrogen through water splitting [139]. Similar to other applications, the utilization of single-phase photocatalysts often yields suboptimal catalytic activity, prompting interest in the modification of these materials through the incorporation of carbonaceous supports. In this context, biochars emerge as an economically advantageous alternative when compared with other carbonaceous materials such as graphene or carbon nanotubes. Notably, catalysts relying on titanium dioxide (TiO2), zinc germanate (ZnGe2O4), or carbon nitride, among others, have been explored, yet their efficiency remains distant from practical applications [140]. In a notable study, Yang et al. engineered Co-Al catalysts supported on biochar derived from cherry blossoms, yielding highly satisfactory results. This outcome suggests that the biochar can adeptly accommodate photoexcited electrons, thereby fostering the catalytic reduction of CO2 to CO [141]. Additionally, the hydrophilic or hydrophobic nature of the photocatalyst significantly influences the conversion outcomes, given that CO2 exhibits enhanced adsorption on hydrophobic materials. This challenge compounds the limitations of conventional metal oxide-based photocatalysts, primarily characterized by hydrophilicity. Consequently, the utilization of a hydrophobic material such as biochar confers an amphiphilic character to the catalyst, furnishing a more favorable surface for CO2 adsorption along with a hydrophilic component that enhances charge transfer [140]. Concerning water splitting, there exists noteworthy research wherein photocatalysts are developed through a synergistic combination of a semiconductor and biochar. For instance, Bhavani et al. conducted a study in which they prepared ZnIn2S4 catalysts supported on biochar sourced from rice husk, achieving highly intriguing catalytic results [142].
In summary, photocatalysis, a crucial field for chemical reactions under light, finds notable application in wastewater remediation and carbon dioxide conversion. Biochar, when used as a supporting material, addresses challenges associated with traditional photocatalysts. It enhances electron–hole separation, reduces the bandgap, and allows better utilization of visible light. Biochar-type choice and surface groups play crucial roles in its performance. Synergistic effects with other catalysts improve responsiveness to visible light. Certain biochars exhibit inherent photocatalytic activity, especially those with oxygenated groups. Biochar-supported catalysts show promise in converting carbon dioxide and environmentally clean hydrogen generation. Future research should optimize biochar properties, explore catalyst combinations, and understand the mechanisms for enhanced photocatalytic performance. The use of biochar in photocatalysis offers an economically advantageous and environmentally friendly alternative for sustainable applications.

3.5. Electrocatalysis

Fuel cells are devices aimed at converting chemical energy into electrical energy without combustion. In this process, fuels such as hydrogen undergo oxidation in the anode, producing electrons and either H+ or H2O in acidic and alkaline electrolytes, respectively. Subsequently, the electrons flow to the cathode, where they participate in the reduction of O2 to either H2O or OH. This unique electrochemical process contributes to the higher energy efficiency and reduced environmental impact of fuel cells compared with traditional diesel or gas engines [143]. The efficiency and environmental benefits of fuel cells are inherently tied to their electrochemical processes, wherein hydrogen oxidation reaction (HER) at the anode and oxygen reduction reaction (ORR) at the cathode play crucial roles in converting chemical energy into electricity.
Cutting-edge electrocatalysts employed in ORR, oxygen evolution reaction (OER), and HER typically rely on precious metal-based materials such as platinum or its alloys for ORR and HER, and RuO2 or IrO2 for OER [144]. Despite their exceptional catalytic performance, these precious metal catalysts face significant drawbacks, including high cost and scarcity, making large-scale applications economically challenging. Moreover, these materials encounter stability issues that can compromise their long-term effectiveness, necessitating the exploration of alternative, cost-effective, and more sustainable catalysts for advancing electrochemical technologies [144].
Due to the widespread availability of carbon and its favorable conductivity, along with the ability to finely tune its structural and physicochemical properties [145], carbon-based materials have emerged as highly promising catalysts for ORR, OER, and HER [146,147]. Notably, carbon-based catalysts offer advantages over their non-precious transition metal counterparts, including relatively lower cost, reduced heavy metal pollution, and environmental friendliness [148]. Beyond commonly known forms like graphite, diamond, and amorphous carbon, various carbon allotropes exist, encompassing 0D fullerene, 1D CNT, 2D graphene, and 3D graphitic carbons, among others [144]. For instance, graphene exhibits a substantial surface area and excellent electrical conductivity, positioning it as a promising material for electrocatalysis. Its attributes facilitate the effective dispersion of active sites and rapid charge transport, making it particularly advantageous in enhancing catalytic performance [149].
Zhou et al. showed a novel strategy for developing cost-effective metal-free catalysts with exceptional activity and stability for ORR in their work, serving as potential alternatives to carbon-supported platinum catalysts (Pt/C). The approach involves the fabrication of self-constructed carbon nanoparticle (CNP)-coated porous biocarbon derived from the plant moss Weisiopsis anomala, a readily available and renewable precursor. The CNPs are self-synthesized and incorporated into the moss-derived carbon matrix through hydrothermal treatment and subsequent carbonization at 900 °C. The resulting CNP-coated biocarbon exhibits a larger surface area compared with CNP-free counterparts. Electrochemical assessments reveal outstanding ORR activity for the CNP-coated biocarbon, with an onset potential of 0.935 V vs. the reversible hydrogen electrode (RHE), closely rivaling commercial Pt/C catalysts (0.962 V vs. RHE) and surpassing CNP-free biocarbon. Additionally, the CNP-coated biocarbons demonstrate high limited current density, long-term stability, and resistance to methanol crossover, outperforming Pt/C [150].
In the work of Huang et al., the significance of biomass-derived carbons through HTC for diverse applications, emphasizing their cost-effectiveness, eco-friendly nature, and suitability for catalysis, is shown. The study introduces a novel approach to HTC, incorporating the biomolecule guanine and various carbohydrates (i.e., glucose, fructose, and cellulose) as carbon precursors, resulting in the formation of 2D crystalline carbonaceous materials. High-temperature carbonization yielded hierarchical porous nitrogen-doped carbons with notable surface areas and nitrogen contents. The resulting 2D carbonaceous materials exhibit exceptional performance in ORR and HER, surpassing Pt-based electrocatalysts [151].
Similarly, the work of Li et al. explores a straightforward method to control the morphology and structure of biomass-derived carbonaceous materials, utilizing the unique cordyceps-like 3D structure of rice husk formed through high-temperature carbonization, with SiC as the main component. The well-organized cordyceps-like SiC structure demonstrates remarkable structural/chemical stability and high electron migration rates, serving as a stable substrate for metal deposition and finding application in electrocatalysis. These natural Si-C composite materials overcome limitations imposed by the intricate internal structure of silicon-rich biomass, offering a new avenue to maximize the utilization of rice husk-based carbon and expanding its application field, including hydrogen production through water electrolysis [152].
Mijowska et al. investigate hydrogen technology in their study, specifically focusing on nickel phosphide-based electrocatalysts known for their effectiveness in HER and OER. They introduce a simple strategy involving the production of highly porous carbon flakes derived from cellulose fibers, exhibiting exceptional specific surface area (3164 m2/g) after activation at 850 °C. The resulting composite of Ni12P5 and carbon flakes (100:1 ratio) demonstrates superior kinetics for the OER, outstanding durability, and stability under high current density, making it a promising candidate for practical applications [153]. As shown in Figure 8a, the Ni12P5_cellulose_1:100 sample demonstrated the smallest overpotential at 10 mA cm−2 current density (η = 338 mV) in comparison with other ratios. The uniform deposition of Ni12P5 nanoparticles on the carbon sample contributed to the enhanced electrocatalytic activity, highlighting the potential for further modifications for increased effectiveness. Figure 8b shows the Tafel slope, an important parameter indicating electrocatalytic activity. It provides insights into the efficiency of a material in electrochemical reactions. A lower Tafel slope generally signifies a more efficient electrocatalyst. In this study, Ni12P5_cellulose_1:100 displayed the lowest Tafel slope, indicating superior electrocatalytic efficiency compared with other composites. Interestingly, the Tafel slope decreased with increasing Ni12P5 content, suggesting a change in the rate-determining step and improved reaction kinetics [153].
Despite subjecting biomass-derived carbon to high-temperature carbonization, the resulting material often retains a lower degree of crystallization or graphitization, contributing to a substantial presence of structural disorders. This inherent disorderliness becomes a limiting factor in facilitating fast charge transfer within the carbon framework. Moreover, carbonaceous materials with pronounced disorder tend to exhibit reduced resistance to corrosion in harsh environments, which is a drawback for achieving prolonged catalytic stability [39]. To address these challenges and enhance catalytic performance, transition metal salt catalysts are frequently incorporated during the synthesis process. These catalysts not only contribute to the improvement in crystalline structure but also play a crucial role in introducing and activating more active species within the carbon matrix [144]. This approach aims to overcome the inherent limitations of disorder in biomass-derived carbon, promoting enhanced charge transfer and catalytic stability for various applications.
Biomass-derived carbonaceous materials encounter various challenges. Firstly, biomass often lacks certain heteroatoms, necessitating an additional source, potentially leading to poor material homogeneity [154,155]. Structural control of biomass-derived carbon is challenging, lacking guiding principles for nanostructured design [156]. Variability among materials from the same biomass precursor poses a reproducibility challenge. Impurities in biomass precursors are hard to remove entirely, and their roles in electrocatalysis are unclear. Finally, optimization of the graphitization degree, structure, morphology, and porosity of biomass-derived carbonaceous materials is essential [157].
In conclusion, fuel cells stand as efficient and environmentally friendly devices in converting chemical energy to electricity through electrochemical processes, with HER at the anode and ORR at the cathode playing pivotal roles. The current reliance on precious metal-based catalysts presents challenges, including cost and stability issues, urging the exploration of alternative, sustainable materials. Carbonaceous materials, owing to their abundance, tunability, and favorable conductivity, emerge as promising candidates for ORR, OER, and HER electrocatalysts. The presented studies of carbonaceous materials derived from biomass highlight the potential of these materials in advancing electrochemical technologies. However, challenges persist, such as structural control, material homogeneity, and the need for optimization in biomass-derived carbonaceous materials. Future research should focus on overcoming these challenges and developing more efficient and sustainable electrocatalysts for widespread application in energy conversion technologies.

3.6. Microbial Fuel Cell Electrodes

Fuel cells are devices aimed at converting chemical energy into electrical energy without combustion. Microbial Fuel Cells (MFCs), a type of electrochemical fuel cell, use microorganisms to oxidize organic matter in wastewater. Typically, MFCs include an anode and a cathode separated by a proton exchange membrane like Nafion or poly(tetrafluoroethylene). The bacterial biofilm in the anode acts as a catalyst, transforming organic molecule energy into electrons, while oxygen is reduced at the cathode to form water [158]. Figure 9 shows a schematic representation of a typical MFC.
Designing suitable bio-anodes is crucial to broadening the applications of MFCs. Moreover, the substantial expense associated with components utilized in MFC reactors is a significant constraint, impeding the timely commercial deployment of this technology [62]. Significant advancements in developing highly efficient electrode materials for MFCs have been recently developed. Among the sustainable materials used for this purpose, carbon-based materials are highlighted [159,160].
Carbon-based electrodes are frequently utilized in MFCs owing to their biocompatibility, extended durability, excellent conductivity, and cost-effectiveness. The versatility of carbon materials lies in their ability to manifest diverse morphologies and structures, facilitating the design of attractive and efficient electrodes [161]. In particular, carbon-based anodes play a crucial role in MFCs by promoting the efficient attachment of bacteria. Additionally, these anodes establish a conductive pathway for electron transfer, contributing to the overall efficacy of the MFC system [160,161].
Liu et al. conducted an experiment utilizing eight graphite anodes paired with a single cathode in a single-chambered MFC. They observed a notable 80% decrease in chemical oxygen demand from the initial value using these anodes. However, despite this reduction, the maximum power achieved was approximately 26 mW/m, highlighting a limitation in the use of low-porosity carbon rods within MFCs [162].
To address the issue of low surface area, Lovley et al. successfully employed materials with higher surface areas, such as graphite felt electrodes. This modification led to a threefold increase in the maximum current produced, emphasizing the significance of electrode surface area in MFC performance [163]. Another innovative approach, implemented by Logan et al., utilized a graphite fiber brush electrode wound around a titanium wire to augment the surface area and facilitate microbial inoculation. This modification resulted in a remarkable maximum power density of up to 2400 mW/m, approximately four times higher than that achieved with carbon paper electrodes [164,165]. Additionally, the use of carbon cloth, a material similar to graphite felt, demonstrated a noteworthy maximum power density of up to 483 mW/m [166]. These advancements underscore the importance of optimizing electrode materials and surface areas to enhance the overall performance of MFCs.
Carbon materials exhibiting thin, two-dimensional morphologies, such as carbon paper, cloth, or mesh, hold great promise as anode materials in MFCs. In contrast to the graphite-based anodes discussed earlier, these morphologies offer distinct advantages in minimizing the separation distance between the two electrodes. This reduction in distance not only diminishes the overall dimensions of the MFC device but also holds the potential to enhance MFC performance [167].
The utilization of such materials addresses the challenge of electrode spacing, contributing to the optimization of MFC design. The proximity of the electrodes facilitates more efficient electron transfer and microbial interactions, ultimately improving the overall functionality of MFCs [158].
Carbon nanotubes (CNTs), distinctive allotropes of carbon, are also a highly promising alternative for MFC electrodes. This stems from their remarkable attributes, including unique electrical conductivity, chemical stability, biocompatibility, high specific area, and catalytic properties [168]. Notably, CNTs exhibit strong cell adhesion, cell attachment, and growth properties, as reported in previous studies [169,170].
Recent research by Erbay et al. highlights the exceptional charge transfer characteristics of microbes grown on CNTs, attributed to the stacking interaction between the carbon atoms of graphite and the cellular outgrowths of microorganisms [171]. Growing CNTs directly over a stainless steel mesh helps maintain low ohmic resistance. The observed advantage of spaces between CNTs facilitates microbe inoculation, and the minimal presence of amorphous carbon contributes to excellent charge interaction. In a related development, Tsai et al. coated CNTs onto carbon cloth to create a highly conductive MFC anode with an expanded surface area, resulting in a notable 250 percent improvement in maximum power density [172].
As shown before, CNTs have emerged as one of the most promising electrode materials, owing to their expansive specific surface area, high mechanical strength, ductility, and outstanding stability and conductivity. Notably, recent attention has focused on conductive polymer/CNT composites, recognizing the synergistic effects that arise from incorporating CNTs into conductive polymers [173].
Qiao et al. explored the feasibility of an MFC utilizing a CNT/polyaniline composite as the anode material. Their findings suggested that CNTs could augment the electrode surface area and electron transfer capability. Furthermore, polyaniline, acting as a conductive polymer, not only offered protective benefits to microorganisms but also enhanced the electro-catalytic activity of the catalyst [174].
In another study, Sharma et al. developed an MFC with a carbon paper anode coated with multi-walled CNTs. Surprisingly, they observed a six-fold increase in power density compared with that achieved with a pure graphite electrode. This improvement was attributed to carboxyl groups on the surface of multi-walled CNTs, which heightened the chemical reactivity of metal nanoparticles [175].
Zou et al. employed polypyrrole (PPy)/CNTs as the anode material, revealing superior electrochemical properties of the modified carbon paper [176]. Tsai et al. supported the idea that a modified electrode could enhance MFC performance. In comparison with an unmodified electrode, they observed a remarkable 148% increase in power density and a 147% increase in cell voltage [172]. These studies underscore the versatility and efficacy of CNTs and conductive polymer/CNT composites in advancing the capabilities of MFC anodes.
Alternatively, Zhu et al. used sludge-derived carbon-modified material in their work as an anode in an MFC. They prepared different electrodes using several carbonization temperatures. These authors found that MFCs with sludge carbon electrodes, especially those obtained at a carbonization temperature of 1000 °C, exhibited improved performance in chemical oxygen demand removal efficiency, organic matter degradation, and electrochemical oxidation activity compared with carbon cloth electrodes. The sludge carbonization temperature significantly influenced MFC system voltage output, with sludge carbon electrodes consistently outperforming carbon cloth electrodes [177]. This can be seen in Figure 10.
In conclusion, MFCs show promise in converting organic matter into electricity, with bio-anode design being a critical factor. Carbonaceous materials, owing to their biocompatibility, durability, and conductivity, play a pivotal role in enhancing MFC performance. Recent advancements include utilizing materials like graphite felt, carbon cloth, and CNTs to optimize electrode surface area and facilitate efficient electron transfer. Notably, CNTs, either alone or in composite materials with conductive polymers, exhibit exceptional electrochemical properties, offering improved power density and electron transfer capabilities. Future research should focus on further optimizing carbon-based materials, exploring new composites, and understanding microbial interactions to advance the commercial viability of MFC technology. The field holds promise for sustainable energy generation and wastewater treatment, provided ongoing efforts continue to refine and innovate electrode materials in MFCs.

3.7. Pollutant Removal

Advanced oxidation processes (AOPs) are delineated as oxidation methodologies wherein hydroxyl radicals (-OH) are generated to effectuate the removal of pollutants from aqueous and gaseous media [178]. These processes offer notable advantages over alternative chemical methods in pollutant treatment, as they exhibit enhanced efficiency and obviate the generation of secondary pollutants [179]. Among the AOPs, ozonation stands out, producing -OH radicals adept at pollutant degradation [180]. Particularly noteworthy are certain metal oxides, such as MnO2, Fe2O3, and MgO, which, when supported on materials featuring developed textural properties, exhibit heightened catalytic activity. In a study conducted by Tian et al., MnOx and FeOx catalysts were meticulously prepared, supported on diverse biochars, for the ozonation treatment of trizine. The favorable porous characteristics of the biochars facilitate pollutant adsorption, and the well-dispersed metal phase enables the exposed surface atoms, typically coated with hydroxyl groups, to manifest as Lewis acids during the ozone decomposition process [181]. The intrinsic characteristics of biochar are pivotal, particularly when it contains catalytically active metal oxides. Chen et al. systematically fabricated biochars derived from refinery sewage sludge characterized by elevated carbon content, Si-O functional groups, and embedded metal oxides capable of catalyzing ozonation through hydroxyl radical generation. Notably, the biochar’s surface oxygenated groups, such as carboxylic acids or lactones, autonomously promote ozone decomposition without necessitating additional support materials [182]. However, the potential leaching of the catalytically active phase raises concerns about secondary contamination, thus instigating a notable interest in the utilization of free-metal catalysts. Cheng et al. addressed this concern by crafting biochar from corn straws and subsequently nitrogen-doping it through urea treatment to modulate its surface properties. The resulting biochar exhibited electron-rich oxygenated groups, conjugated heteroatoms, and defect sites endowed with free electrons, which collectively played a pivotal role in ozone decomposition for the removal of atrazine. The achieved removal rates reached 74%, emphasizing the efficacy of tailored biochar in AOPs for pollutant remediation [183]. This methodology exhibits utility not solely in water pollutant removal scenarios. Cha et al. innovatively synthesized a catalytic system comprising manganese oxides (MnOx) supported on biochar for the room-temperature ozone catalytic oxidation of toluene, an unprecedented endeavor in the literature. Their findings revealed a notable efficiency of 90%, albeit without achieving complete oxidation to CO and CO2 [184].
An exemplary process known for its efficiency is the Fenton process, predicated on the catalytic capability of ferrous ions (Fe2+) to decompose H2O2 into hydroxyl radicals [185]. Biochars present intriguing potential as supports for Fe catalysts, and Esteves et al. conducted a comprehensive investigation involving the preparation of a series of biochars derived from olive oil industry waste. These biochars were employed for the purification of water contaminated by agro-food facilities. The intricate interactions between phenolic groups and the catalyst surface are contingent upon the porous properties of the biochars and the chemical interplay between the pollutant and the adsorbent surface, specifically surface groups. These factors collectively dictate the catalytic properties of the system. Notably, the prepared biochar-based materials demonstrated exceptional performance, yielding conversions exceeding 90% (Figure 11) [186]. A similar approach was proposed by Jian et al. for the degradation of pyrene, a prevalent polycyclic aromatic compound in water, ultimately achieving total oxidation [187].
An additional crucial process involves the decomposition of peroxymonosulphate (PMS) or peroxydisulphate (PDS) to generate sulfate radicals (SO4•), which typically exhibit high oxidative selectivity and a relatively prolonged lifetime. Although homogeneous transition metals display notable activity, their effectiveness is impeded by challenges associated with separation, and their presence often fails to prevent leaching. As an alternative strategy, various studies have demonstrated the exceptional efficacy of carbonaceous materials in activating PMS and PDS, with biochars, in particular, showcasing commendable adsorption and catalytic degradation capabilities [188]. Functional groups within carbonaceous materials play a pivotal role in influencing adsorptive properties. Consequently, several researchers have undertaken the preparation of biochars derived from biomass for these oxidation processes. For instance, Zhu et al. synthesized biochars from wood for the degradation of clofibric acid using PDS, achieving an impressive 98% conversion within a one-hour timeframe [189]. He et al. fabricated biochars from sugarcane residues characterized by a high surface area and excellent electron transfer ability, resulting in a 100% bisphenol A degradation efficiency within one hour, along with a PMS decomposition efficiency of 58% [190]. In a similar vein, Guo et al. utilized Fe catalysts derived from a mineral with elevated Fe2O3 content. However, it has been established that the catalytically active species for PDS decomposition is Fe0, necessitating stabilization. This is achieved through the co-pyrolysis of biochar sources (solid residues of red mud and coconut bark) with the metal catalyst, culminating in the production of stabilized Fe0. Remarkably, this methodology exhibits excellent PDS activation, leading to the complete removal of orange 7 within 30 min [191].
Table 3 provides a summary of diverse solid-base catalysts derived from biomass for AOP.
In conclusion, advanced oxidation processes, notably ozonation and the Fenton process, offer efficient avenues for pollutant removal. Biochars, when tailored with catalytically active metal oxides or used as supports for Fe catalysts, demonstrate exceptional efficacy in these processes. The intrinsic properties of biochar, such as developed textural characteristics and surface oxygenated groups, contribute to enhanced catalytic activity. Additionally, biochars play a crucial role in activating PMS or PDS for sulfate radical generation, showcasing commendable adsorption and catalytic degradation capabilities. Future research should delve into optimizing biochar synthesis, exploring new catalyst–biochar combinations and addressing potential challenges like leaching in AOPs. These developments will contribute to advancing the effectiveness and applicability of biochar-based materials in environmental remediation processes.

4. Conclusions

Herein we have reviewed the main advances in the field of using renewable carbonaceous materials in catalytic processes. The studies reviewed confirm the technical viability of the applications proposed in most cases. For biofuel production, biochar-supported catalysts have proved to be able to achieve biodiesel production with yields exceeding 70%. Notably, hydrochars and activated carbons derived from diverse biomass sources have demonstrated significant tar removal efficiency. For instance, rice husk char exhibited an increased BET surface area from 2.2 m2/g to 141 m2/g after pyrolysis at 600 °C, showcasing its effectiveness in adsorbing phenol and light aromatic hydrocarbons. Concerning chemical production and the oxidation of alcohols, the influence of biochar quantity and pre-calcination temperature on catalytic performance has been proven, achieving selectivity toward benzaldehyde exceeding 70%. In aldehyde oxidation, biochars co-doped with selenium and nitrogen exhibited yields exceeding 90%. When it comes to hydrogenation reactions, biochar-supported Pd catalysts showed total conversion of benzaldehyde to toluene within 2 h, while in the reduction of nitroarenes, RuO2 and Pt catalysts on biochar achieved conversions exceeding 97%, with the incorporation of Fe3O4 enhancing recyclability. In the discipline of photocatalysis, particularly in wastewater remediation, the importance relies on catalysts like TiO2. Biochars, when incorporated into TiO2 composites, address challenges such as bandgap limitations and electron–hole recombination, enhancing catalytic activity. Renewable CNT–stainless steel mesh electrodes demonstrated exceptional charge transfer, achieving a 250% increase in power density by coating CNTs onto carbon cloth. Furthermore, tailored biochars, rich in surface oxygenated groups, serve as effective catalysts for ozone decomposition, achieving significant pollutant removal rates, exemplified by the removal of atrazine at 74%. All in all, this review paper showcases the importance of renewable carbonaceous materials in the path toward sustainable carbon-based compounds for catalytic applications.

Funding

This research was funded by the FJC2021–047672-I grant co-financed by MCIN/AEI/10.13039/501100011033 and the European Union NextGenerationEU/PRTR funds.

Institutional Review Board Statement

Not applicable.

Informed Consent Statement

Not applicable.

Data Availability Statement

Not applicable.

Conflicts of Interest

The authors declare no conflict of interest.

References

  1. López-Salas, N.; Antonietti, M. Carbonaceous Materials: The Beauty of Simplicity. Bull. Chem. Soc. Jpn. 2021, 94, 2822–2828. [Google Scholar] [CrossRef]
  2. González-Arias, J.; Sánchez, M.E.; Cara-Jiménez, J. Profitability Analysis of Thermochemical Processes for Biomass-Waste Valorization: A Comparison of Dry vs Wet Treatments. Sci. Total Environ. 2022, 811, 152240. [Google Scholar] [CrossRef]
  3. González-Arias, J.; Carnicero, A.; Sánchez, M.E.; Martínez, E.J.; López, R.; Cara-Jiménez, J. Management of Off-Specification Compost by Using Co-Hydrothermal Carbonization with Olive Tree Pruning. Assessing Energy Potential of Hydrochar. Waste Manag. 2021, 124, 224–234. [Google Scholar] [CrossRef]
  4. Xiong, X.; Yu, I.K.M.; Cao, L.; Tsang, D.C.W.; Zhang, S.; Ok, Y.S. A Review of Biochar-Based Catalysts for Chemical Synthesis, Biofuel Production, and Pollution Control. Bioresour. Technol. 2017, 246, 254–270. [Google Scholar] [CrossRef]
  5. Anto, S.; Sudhakar, M.P.; Shan Ahamed, T.; Samuel, M.S.; Mathimani, T.; Brindhadevi, K.; Pugazhendhi, A. Activation Strategies for Biochar to Use as an Efficient Catalyst in Various Applications. Fuel 2021, 285, 119205. [Google Scholar] [CrossRef]
  6. Yao, D.; Hu, Q.; Wang, D.; Yang, H.; Wu, C.; Wang, X.; Chen, H. Hydrogen Production from Biomass Gasification Using Biochar as a Catalyst/Support. Bioresour. Technol. 2016, 216, 159–164. [Google Scholar] [CrossRef]
  7. Chen, W.; Fang, Y.; Li, K.; Chen, Z.; Xia, M.; Gong, M.; Chen, Y.; Yang, H.; Tu, X.; Chen, H. Bamboo Wastes Catalytic Pyrolysis with N-Doped Biochar Catalyst for Phenols Products. Appl. Energy 2020, 260, 114242. [Google Scholar] [CrossRef]
  8. Dehkhoda, A.M.; West, A.H.; Ellis, N. Biochar Based Solid Acid Catalyst for Biodiesel Production. Appl. Catal. A Gen. 2010, 382, 197–204. [Google Scholar] [CrossRef]
  9. Vassilev, S.V.; Baxter, D.; Vassileva, C.G. An Overview of the Behaviour of Biomass during Combustion: Part I. Phase-Mineral Transformations of Organic and Inorganic Matter. Fuel 2013, 112, 391–449. [Google Scholar] [CrossRef]
  10. Suhas; Carrott, P.J.M.; Ribeiro Carrott, M.M.L. Lignin—From Natural Adsorbent to Activated Carbon: A Review. Bioresour. Technol. 2007, 98, 2301–2312. [Google Scholar] [CrossRef]
  11. Wang, Z.; Shen, D.; Wu, C.; Gu, S. State-of-the-Art on the Production and Application of Carbon Nanomaterials from Biomass. Green Chem. 2018, 20, 5031–5057. [Google Scholar] [CrossRef]
  12. Kim, D.; Yoshikawa, K.; Park, K.Y. Characteristics of Biochar Obtained by Hydrothermal Carbonization of Cellulose for Renewable Energy. Energies 2015, 8, 12412. [Google Scholar] [CrossRef]
  13. Dhyani, V.; Bhaskar, T. A Comprehensive Review on the Pyrolysis of Lignocellulosic Biomass. Renew. Energy 2018, 129, 695–716. [Google Scholar] [CrossRef]
  14. Lan, G.; Yang, J.; Ye, R.P.; Boyjoo, Y.; Liang, J.; Liu, X.; Li, Y.; Liu, J.; Qian, K. Sustainable Carbon Materials toward Emerging Applications. Small Methods 2021, 5, 2001250. [Google Scholar] [CrossRef]
  15. González-Arias, J.; Gómez, X.; González-Castaño, M.; Sánchez, M.E.; Rosas, J.G.; Cara-Jiménez, J. Insights into the Product Quality and Energy Requirements for Solid Biofuel Production: A Comparison of Hydrothermal Carbonization, Pyrolysis and Torrefaction of Olive Tree Pruning. Energy 2022, 238, 122022. [Google Scholar] [CrossRef]
  16. Chen, W.H.; Lin, B.J.; Lin, Y.Y.; Chu, Y.S.; Ubando, A.T.; Show, P.L.; Ong, H.C.; Chang, J.S.; Ho, S.H.; Culaba, A.B.; et al. Progress in Biomass Torrefaction: Principles, Applications and Challenges. Prog. Energy Combust. Sci. 2021, 82, 100887. [Google Scholar] [CrossRef]
  17. van der Stelt, M.J.C.; Gerhauser, H.; Kiel, J.H.A.; Ptasinski, K.J. Biomass Upgrading by Torrefaction for the Production of Biofuels: A Review. Biomass Bioenergy 2011, 35, 3748–3762. [Google Scholar] [CrossRef]
  18. Bridgwater, A.V. Review of Fast Pyrolysis of Biomass and Product Upgrading. Biomass Bioenergy 2012, 38, 68–94. [Google Scholar] [CrossRef]
  19. Wang, T.; Liu, H.; Duan, C.; Xu, R.; Zhang, Z.; She, D.; Zheng, J. The Eco-Friendly Biochar and Valuable Bio-Oil from Caragana Korshinskii: Pyrolysis Preparation, Characterization, and Adsorption Applications. Materials 2020, 13, 3391. [Google Scholar] [CrossRef]
  20. Zhang, D.; Wang, T.; Zhi, J.; Zheng, Q.; Chen, Q.; Zhang, C.; Li, Y. Utilization of Jujube Biomass to Prepare Biochar by Pyrolysis and Activation: Characterization, Adsorption Characteristics, and Mechanisms for Nitrogen. Materials 2020, 13, 5594. [Google Scholar] [CrossRef] [PubMed]
  21. Kazimierski, P.; Januszewicz, K.; Godlewski, W.; Fijuk, A.; Suchocki, T.; Chaja, P.; Barczak, B.; Kardaś, D. The Course and the Effects of Agricultural Biomass Pyrolysis in the Production of High-Calorific Biochar. Materials 2022, 15, 1038. [Google Scholar] [CrossRef] [PubMed]
  22. Wang, G.; Dai, Y.; Yang, H.; Xiong, Q.; Wang, K.; Zhou, J.; Li, Y.; Wang, S. A Review of Recent Advances in Biomass Pyrolysis. Energy Fuels 2020, 34, 15557–15578. [Google Scholar] [CrossRef]
  23. Lv, D.; Xu, M.; Liu, X.; Zhan, Z.; Li, Z.; Yao, H. Effect of Cellulose, Lignin, Alkali and Alkaline Earth Metallic Species on Biomass Pyrolysis and Gasification. Fuel Process. Technol. 2010, 91, 903–909. [Google Scholar] [CrossRef]
  24. Collard, F.X.; Blin, J. A Review on Pyrolysis of Biomass Constituents: Mechanisms and Composition of the Products Obtained from the Conversion of Cellulose, Hemicelluloses and Lignin. Renew. Sustain. Energy Rev. 2014, 38, 594–608. [Google Scholar] [CrossRef]
  25. Lee, Y.; Park, J.; Ryu, C.; Gang, K.S.; Yang, W.; Park, Y.K.; Jung, J.; Hyun, S. Comparison of Biochar Properties from Biomass Residues Produced by Slow Pyrolysis at 500 °C. Bioresour. Technol. 2013, 148, 196–201. [Google Scholar] [CrossRef]
  26. Akhtar, J.; Saidina Amin, N. A Review on Operating Parameters for Optimum Liquid Oil Yield in Biomass Pyrolysis. Renew. Sustain. Energy Rev. 2012, 16, 5101–5109. [Google Scholar] [CrossRef]
  27. Mani, T.; Murugan, P.; Abedi, J.; Mahinpey, N. Pyrolysis of Wheat Straw in a Thermogravimetric Analyzer: Effect of Particle Size and Heating Rate on Devolatilization and Estimation of Global Kinetics. Chem. Eng. Res. Des. 2010, 88, 952–958. [Google Scholar] [CrossRef]
  28. Zhao, B.; O’Connor, D.; Zhang, J.; Peng, T.; Shen, Z.; Tsang, D.C.W.; Hou, D. Effect of Pyrolysis Temperature, Heating Rate, and Residence Time on Rapeseed Stem Derived Biochar. J. Clean. Prod. 2018, 174, 977–987. [Google Scholar] [CrossRef]
  29. Kim, K.H.; Eom, I.Y.; Lee, S.M.; Choi, D.; Yeo, H.; Choi, I.G.; Choi, J.W. Investigation of Physicochemical Properties of Biooils Produced from Yellow Poplar Wood (Liriodendron tulipifera) at Various Temperatures and Residence Times. J. Anal. Appl. Pyrolysis 2011, 92, 2–9. [Google Scholar] [CrossRef]
  30. Yang, D.P.; Li, Z.; Liu, M.; Zhang, X.; Chen, Y.; Xue, H.; Ye, E.; Luque, R. Biomass-Derived Carbonaceous Materials: Recent Progress in Synthetic Approaches, Advantages, and Applications. ACS Sustain. Chem. Eng. 2019, 7, 4564–4585. [Google Scholar] [CrossRef]
  31. González-Arias, J.; Baena-Moreno, F.M.; Sánchez, M.E.; Cara-Jiménez, J. Optimizing Hydrothermal Carbonization of Olive Tree Pruning: A Techno-Economic Analysis Based on Experimental Results. Sci. Total Environ. 2021, 784, 147169. [Google Scholar] [CrossRef]
  32. González-Arias, J.; Sánchez, M.E.; Cara-Jiménez, J.; Baena-Moreno, F.M.; Zhang, Z. Hydrothermal Carbonization of Biomass and Waste: A Review. Environ. Chem. Lett. 2022, 20, 211–221. [Google Scholar] [CrossRef]
  33. Nizamuddin, S.; Baloch, H.A.; Griffin, G.J.; Mubarak, N.M.; Bhutto, A.W.; Abro, R.; Mazari, S.A.; Ali, B.S. An Overview of Effect of Process Parameters on Hydrothermal Carbonization of Biomass. Renew. Sustain. Energy Rev. 2017, 73, 1289–1299. [Google Scholar] [CrossRef]
  34. González-Arias, J.; Sánchez, M.E.; Martínez, E.J.; Covalski, C.; Alonso-Simón, A.; González, R.; Cara-Jiménez, J. Hydrothermal Carbonization of Olive Tree Pruning as a Sustainable Way for Improving Biomass Energy Potential: Effect of Reaction Parameters on Fuel Properties. Processes 2020, 8, 1201. [Google Scholar] [CrossRef]
  35. Nakason, K.; Panyapinyopol, B.; Kanokkantapong, V.; Viriya-empikul, N.; Kraithong, W.; Pavasant, P. Hydrothermal Carbonization of Unwanted Biomass Materials: Effect of Process Temperature and Retention Time on Hydrochar and Liquid Fraction. J. Energy Inst. 2018, 91, 786–796. [Google Scholar] [CrossRef]
  36. Liu, F.; Yu, R.; Guo, M. Hydrothermal Carbonization of Forestry Residues: Influence of Reaction Temperature on Holocellulose-Derived Hydrochar Properties. J. Mater. Sci. 2017, 52, 1736–1746. [Google Scholar] [CrossRef]
  37. Lu, X.; Pellechia, P.J.; Flora, J.R.V.; Berge, N.D. Influence of Reaction Time and Temperature on Product Formation and Characteristics Associated with the Hydrothermal Carbonization of Cellulose. Bioresour. Technol. 2013, 138, 180–190. [Google Scholar] [CrossRef]
  38. López, R.; González-Arias, J.; Pereira, F.J.; Fernández, C.; Cara-Jiménez, J. A Techno-Economic Study of HTC Processes Coupled with Power Facilities and Oxy-Combustion Systems. Energy 2021, 219, 119651. [Google Scholar] [CrossRef]
  39. Wang, J.; Nie, P.; Ding, B.; Dong, S.; Hao, X.; Dou, H.; Zhang, X. Biomass Derived Carbon for Energy Storage Devices. J. Mater. Chem. A Mater. 2017, 5, 2411–2428. [Google Scholar] [CrossRef]
  40. Ravi, S.; Vadukumpully, S. Sustainable Carbon Nanomaterials: Recent Advances and Its Applications in Energy and Environmental Remediation. J. Environ. Chem. Eng. 2016, 4, 835–856. [Google Scholar] [CrossRef]
  41. Sun, Z.; Fang, S.; Hu, Y.H. 3D Graphene Materials: From Understanding to Design and Synthesis Control. Chem. Rev. 2020, 120, 10336–10453. [Google Scholar] [CrossRef]
  42. Haile, A.; Gelebo, G.G.; Tesfaye, T.; Mengie, W.; Mebrate, M.A.; Abuhay, A.; Limeneh, D.Y. Pulp and Paper Mill Wastes: Utilizations and Prospects for High Value-Added Biomaterials. Bioresour. Bioprocess. 2021, 8, 35. [Google Scholar] [CrossRef]
  43. Mohamad Nor, N.; Lau, L.C.; Lee, K.T.; Mohamed, A.R. Synthesis of Activated Carbon from Lignocellulosic Biomass and Its Applications in Air Pollution Control—A Review. J. Environ. Chem. Eng. 2013, 1, 658–666. [Google Scholar] [CrossRef]
  44. Zhang, B.; Jiang, Y.; Balasubramanian, R. Synthesis, Formation Mechanisms and Applications of Biomass-Derived Carbonaceous Materials: A Critical Review. J. Mater. Chem. A Mater. 2021, 9, 24759–24802. [Google Scholar] [CrossRef]
  45. Barin, G.B.; De Fátima Gimenez, I.; Da Costa, L.P.; Filho, A.G.S.; Barreto, L.S. Influence of Hydrothermal Carbonization on Formation of Curved Graphite Structures Obtained from a Lignocellulosic Precursor. Carbon 2014, 78, 609–612. [Google Scholar] [CrossRef]
  46. Shams, S.S.; Zhang, L.S.; Hu, R.; Zhang, R.; Zhu, J. Synthesis of Graphene from Biomass: A Green Chemistry Approach. Mater. Lett. 2015, 161, 476–479. [Google Scholar] [CrossRef]
  47. Liu, B.; Liu, Y.; Chen, H.; Yang, M.; Li, H. Oxygen and Nitrogen Co-Doped Porous Carbon Nanosheets Derived from Perilla frutescens for High Volumetric Performance Supercapacitors. J. Power Sources 2017, 341, 309–317. [Google Scholar] [CrossRef]
  48. Wang, L.; Zhang, L.C.; Cheng, J.X.; Ding, C.X.; Chen, C.H. Watermelon Used as a Novel Carbon Source to Improve the Rate Performance of Iron Oxide Electrodes for Lithium Ion Batteries. Electrochim. Acta 2013, 102, 306–311. [Google Scholar] [CrossRef]
  49. Sevilla, M.; Fuertes, A.B. Graphitic Carbon Nanostructures from Cellulose. Chem. Phys. Lett. 2010, 490, 63–68. [Google Scholar] [CrossRef]
  50. Qu, J.; Luo, C.; Yuan, X. Synthesis of Hybrid Carbon Nanotubes Using Brassica juncea L. Application to Photodegradation of Bisphenol A. Environ. Sci. Pollut. Res. 2013, 20, 3688–3695. [Google Scholar] [CrossRef]
  51. Liu, W.J.; Tian, K.; He, Y.R.; Jiang, H.; Yu, H.Q. High-Yield Harvest of Nanofibers/Mesoporous Carbon Composite by Pyrolysis of Waste Biomass and Its Application for High Durability Electrochemical Energy Storage. Environ. Sci. Technol. 2014, 48, 13951–13959. [Google Scholar] [CrossRef]
  52. Sun, Z.; Zheng, M.; Hu, H.; Dong, H.; Liang, Y.; Xiao, Y.; Lei, B.; Liu, Y. From Biomass Wastes to Vertically Aligned Graphene Nanosheet Arrays: A Catalyst-Free Synthetic Strategy towards High-Quality Graphene for Electrochemical Energy Storage. Chem. Eng. J. 2018, 336, 550–561. [Google Scholar] [CrossRef]
  53. Rhee, I.; Kim, Y.A.; Shin, G.O.; Kim, J.H.; Muramatsu, H. Compressive Strength Sensitivity of Cement Mortar Using Rice Husk-Derived Graphene with a High Specific Surface Area. Constr. Build. Mater. 2015, 96, 189–197. [Google Scholar] [CrossRef]
  54. Onishchenko, D.V.; Reva, V.P.; Kuryavyi, V.G. Hydrogen Storage in Multilayer Carbon Nanotubes. Coke Chem. 2013, 56, 182–185. [Google Scholar] [CrossRef]
  55. Onishchenko, D.V.; Reva, V.P. Sorption Properties of Multilayer Carbon Nanotubes Produced from Cotton. Coke Chem. 2013, 56, 262–265. [Google Scholar] [CrossRef]
  56. Niu, Q.; Gao, K.; Tang, Q.; Wang, L.; Han, L.; Fang, H.; Zhang, Y.; Wang, S.; Wang, L. Large-Size Graphene-like Porous Carbon Nanosheets with Controllable N-Doped Surface Derived from Sugarcane Bagasse Pith/Chitosan for High Performance Supercapacitors. Carbon 2017, 123, 290–298. [Google Scholar] [CrossRef]
  57. Fathy, N.A. Carbon Nanotubes Synthesis Using Carbonization of Pretreated Rice Straw through Chemical Vapor Deposition of Camphor. RSC Adv. 2017, 7, 28535–28541. [Google Scholar] [CrossRef]
  58. Thompson, E.; Danks, A.E.; Bourgeois, L.; Schnepp, Z. Iron-Catalyzed Graphitization of Biomass. Green Chem. 2015, 17, 551–556. [Google Scholar] [CrossRef]
  59. Debalina, B.; Reddy, R.B.; Vinu, R. Production of Carbon Nanostructures in Biochar, Bio-Oil and Gases from Bagasse via Microwave Assisted Pyrolysis Using Fe and Co as Susceptors. J. Anal. Appl. Pyrolysis 2017, 124, 310–318. [Google Scholar] [CrossRef]
  60. Chen, F.; Yang, J.; Bai, T.; Long, B.; Zhou, X. Facile Synthesis of Few-Layer Graphene from Biomass Waste and Its Application in Lithium Ion Batteries. J. Electroanal. Chem. 2016, 768, 18–26. [Google Scholar] [CrossRef]
  61. Sun, L.; Tian, C.; Li, M.; Meng, X.; Wang, L.; Wang, R.; Yin, J.; Fu, H. From Coconut Shell to Porous Graphene-like Nanosheets for High-Power Supercapacitors. J. Mater. Chem. A Mater. 2013, 1, 6462–6470. [Google Scholar] [CrossRef]
  62. Arenas, C.; Sotres, A.; Alonso, R.M.; González-Arias, J.; Morán, A.; Gómez, X. Pyrolysed Almond Shells Used as Electrodes in Microbial Electrolysis Cell. Biomass Convers. Biorefinery 2022, 12, 313–321. [Google Scholar] [CrossRef]
  63. Yuan, G.; Li, H.; Hu, H.; Xie, Y.; Xiao, Y.; Dong, H.; Liang, Y.; Liu, Y.; Zheng, M. Microstructure Engineering towards Porous Carbon Materials Derived from One Biowaste Precursor for Multiple Energy Storage Applications. Electrochim. Acta 2019, 326, 134974. [Google Scholar] [CrossRef]
  64. Xiao, X.; Chen, B.; Zhu, L.; Schnoor, J.L. Sugar Cane-Converted Graphene-like Material for the Superhigh Adsorption of Organic Pollutants from Water via Coassembly Mechanisms. Environ. Sci. Technol. 2017, 51, 12644–12652. [Google Scholar] [CrossRef]
  65. Wang, A.; Zheng, Z.; Li, R.; Hu, D.; Lu, Y.; Luo, H.; Yan, K. Biomass-Derived Porous Carbon Highly Efficient for Removal of Pb(II) and Cd(II). Green Energy Environ. 2019, 4, 414–423. [Google Scholar] [CrossRef]
  66. Le Saché, E.; Johnson, S.; Pastor-Pérez, L.; Horri, B.A.; Reina, T.R. Biogas Upgrading via Dry Reforming over a Ni-Sn/CeO2-Al2O3 Catalyst: Influence of the Biogas Source. Energies 2019, 12, 1007. [Google Scholar] [CrossRef]
  67. İnan, B.; Koçer, A.T.; Özçimen, D.B. Valorization of Lignocellulosic Wastes for Low-Cost and Sustainable Algal Biodiesel Production Using Biochar-Based Solid Acid Catalyst. J. Anal. Appl. Pyrolysis 2023, 173, 106095. [Google Scholar] [CrossRef]
  68. Johnson, B.J.; Melde, B.J.; Moore, M.H.; Malanoski, A.P.; Taft, J.R. Improving Sorbents for Glycerol Capture in Biodiesel Refinement. Materials 2017, 10, 682. [Google Scholar] [CrossRef]
  69. Orege, J.I.; Oderinde, O.; Kifle, G.A.; Ibikunle, A.A.; Raheem, S.A.; Ejeromedoghene, O.; Okeke, E.S.; Olukowi, O.M.; Orege, O.B.; Fagbohun, E.O.; et al. Recent Advances in Heterogeneous Catalysis for Green Biodiesel Production by Transesterification. Energy Convers. Manag. 2022, 258, 115406. [Google Scholar] [CrossRef]
  70. Lee, D.-W.; Park, Y.-M.; Lee, K.-Y. Heterogeneous Base Catalysts for Transesterification in Biodiesel Synthesis. Catal. Surv. Asia 2009, 13, 63–77. [Google Scholar] [CrossRef]
  71. Azman, N.S.; Khairuddin, N.; Tengku Azmi, T.S.M.; Seenivasagam, S.; Hassan, M.A. Application of Biochar from Woodchip as Catalyst Support for Biodiesel Production. Catalysts 2023, 13, 489. [Google Scholar] [CrossRef]
  72. di Bitonto, L.; Reynel-Ávila, H.E.; Mendoza-Castillo, D.I.; Bonilla-Petriciolet, A.; Durán-Valle, C.J.; Pastore, C. Synthesis and Characterization of Nanostructured Calcium Oxides Supported onto Biochar and Their Application as Catalysts for Biodiesel Production. Renew. Energy 2020, 160, 52–66. [Google Scholar] [CrossRef]
  73. Wang, Y.; Li, O.D.; Zhao, O.D.; Fan, Y.; Bi, J.; Shan, R.; Yang, J.; Luo, B.; Yuan, H.; Ling, X.; et al. Calcium-Loaded Municipal Sludge-Biochar as an Efficient and Stable Catalyst for Biodiesel Production from Vegetable Oil. ACS Omega 2020, 5, 17471–17478. [Google Scholar] [CrossRef] [PubMed]
  74. Daimary, N.; Eldiehy, K.S.H.; Boruah, P.; Deka, D.; Bora, U.; Kakati, B.K. Potato Peels as a Sustainable Source for Biochar, Bio-Oil and a Green Heterogeneous Catalyst for Biodiesel Production. J. Environ. Chem. Eng. 2022, 10, 107108. [Google Scholar] [CrossRef]
  75. Yadav, N.; Yadav, G.; Ahmaruzzaman, M. Fabrication of Surface-Modified Dual Waste-Derived Biochar for Biodiesel Production by Microwave-Assisted Esterification of Oleic Acid: Optimization, Kinetics, and Mechanistic Studies. Renew. Energy 2023, 218, 119308. [Google Scholar] [CrossRef]
  76. Bhatia, S.K.; Gurav, R.; Choi, T.R.; Kim, H.J.; Yang, S.Y.; Song, H.S.; Park, J.Y.; Park, Y.L.; Han, Y.H.; Choi, Y.K.; et al. Conversion of Waste Cooking Oil into Biodiesel Using Heterogenous Catalyst Derived from Cork Biochar. Bioresour. Technol. 2020, 302, 122872. [Google Scholar] [CrossRef]
  77. Gholami, Z.; Gholami, F.; Tišler, Z.; Hubáček, J.; Tomas, M.; Bačiak, M.; Vakili, M. Production of Light Olefins via Fischer-Tropsch Process Using Iron-Based Catalysts: A Review. Catalysts 2022, 12, 174. [Google Scholar] [CrossRef]
  78. Khodakov, A.Y.; Chu, W.; Fongarland, P. Advances in the Development of Novel Cobalt Fischer-Tropsch Catalysts for Synthesis of Long-Chain Hydrocarbons and Clean Fuels. Chem. Rev. 2007, 107, 1692–1744. [Google Scholar] [CrossRef]
  79. Yousefian, F.; Babatabar, M.A.; Eshaghi, M.; Poor, S.M.; Tavasoli, A. Pyrolysis of Rice Husk, Coconut Shell, and Cladophora Glomerata Algae and Application of the Produced Biochars as Support for Cobalt Catalyst in Fischer–Tropsch Synthesis. Fuel Process. Technol. 2023, 247, 107818. [Google Scholar] [CrossRef]
  80. Bai, J.; Qin, C.; Xu, Y.; Xu, D.; Ding, M. Preparation of Nitrogen Doped Biochar-Based Iron Catalyst for Enhancing Gasoline-Range Hydrocarbons Production. ACS Appl. Mater. Interfaces 2022, 14, 45516–45525. [Google Scholar] [CrossRef]
  81. Teimouri, Z.; Abatzoglou, N.; Dalai, A.K. Design of a Renewable Catalyst Support Derived from Biomass with Optimized Textural Features for Fischer Tropsch Synthesis. Renew. Energy 2023, 202, 1096–1109. [Google Scholar] [CrossRef]
  82. Dawood, F.; Anda, M.; Shafiullah, G.M. Hydrogen Production for Energy: An Overview. Int. J. Hydrogen Energy 2020, 45, 3847–3869. [Google Scholar] [CrossRef]
  83. Ishaq, H.; Dincer, I.; Crawford, C. A Review on Hydrogen Production and Utilization: Challenges and Opportunities. Int. J. Hydrogen Energy 2022, 47, 26238–26264. [Google Scholar] [CrossRef]
  84. Zhao, X.; Zhou, X.; Wang, G.; Zhou, P.; Wang, W.; Song, Z. Evaluating the Effect of Torrefaction on the Pyrolysis of Biomass and the Biochar Catalytic Performance on Dry Reforming of Methane. Renew. Energy 2022, 192, 313–325. [Google Scholar] [CrossRef]
  85. Patel, S.; Kundu, S.; Halder, P.; Marzbali, M.H.; Chiang, K.; Surapaneni, A.; Shah, K. Production of Hydrogen by Catalytic Methane Decomposition Using Biochar and Activated Char Produced from Biosolids Pyrolysis. Int. J. Hydrogen Energy 2020, 45, 29978–29992. [Google Scholar] [CrossRef]
  86. Devi, L.; Ptasinski, K.J.; Janssen, F.J.J.G. A Review of the Primary Measures for Tar Elimination in Biomass Gasification Processes. Biomass Bioenergy 2003, 24, 125–140. [Google Scholar] [CrossRef]
  87. González-Arias, J.; Berdugo-Vilches, T.; Mandviwala, C.; Cañete-Vela, I.; Seemann, M.; Thunman, H. Effect of Biomass Ash on Preventing Aromatization of Olefinic Cracking Products in Dual Fluidized Bed Systems. Fuel 2023, 338, 127256. [Google Scholar] [CrossRef]
  88. Ravenni, G.; Sárossy, Z.; Ahrenfeldt, J.; Henriksen, U.B. Activity of Chars and Activated Carbons for Removal and Decomposition of Tar Model Compounds—A Review. Renew. Sustain. Energy Rev. 2018, 94, 1044–1056. [Google Scholar] [CrossRef]
  89. Benedetti, V.; Patuzzi, F.; Baratieri, M. Characterization of Char from Biomass Gasification and Its Similarities with Activated Carbon in Adsorption Applications. Appl. Energy 2018, 227, 92–99. [Google Scholar] [CrossRef]
  90. Brewer, C.E.; Schmidt-Rohr, K.; Satrio, J.A.; Brown, R.C. Characterization of Biochar from Fast Pyrolysis and Gasification Systems. Environ. Prog. Sustain. Energy 2009, 28, 386–396. [Google Scholar] [CrossRef]
  91. Wang, Y.; Hu, Y.J.; Hao, X.; Peng, P.; Shi, J.Y.; Peng, F.; Sun, R.C. Hydrothermal Synthesis and Applications of Advanced Carbonaceous Materials from Biomass: A Review. Adv. Compos. Hybrid. Mater. 2020, 3, 267–284. [Google Scholar] [CrossRef]
  92. Rodríguez-Reinoso, F. The Role of Carbon Materials in Heterogeneous Catalysis. Carbon 1998, 36, 159–175. [Google Scholar] [CrossRef]
  93. Franz, M.; Arafat, H.A.; Pinto, N.G. Effect of Chemical Surface Heterogeneity on the Adsorption Mechanism of Dissolved Aromatics on Activated Carbon. Carbon 2000, 38, 1807–1819. [Google Scholar] [CrossRef]
  94. Zhang, Y.; Feng, D.; Zhao, Y.; Dong, H.; Chang, G.; Quan, C.; Sun, S.; Qin, Y. Evolution of Char Structure during In-Situ Biomass Tar Reforming: Importance of the Coupling Effect among the Physical-Chemical Structure of Char-Based Catalysts. Catalysts 2019, 9, 711. [Google Scholar] [CrossRef]
  95. Cudahy, J.J.; Helsel, R.W. Removal of Products of Incomplete Combustion with Carbon. Waste Manag. 2000, 20, 339–345. [Google Scholar] [CrossRef]
  96. Mastral, A.M.; García, T.; Callén, M.S.; Navarro, M.V.; Galbán, J. Assessement of Phenanthrene Removal from Hot Gas by Porous Carbons. Energy Fuels 2001, 15, 1–7. [Google Scholar] [CrossRef]
  97. Hu, X.; Hanaoka, T.; Sakanishi, K.; Shinagawa, T.; Matsui, S.; Tada, M.; Iwasaki, T. Removal of Tar Model Compounds Produced from Biomass Gasification Using Activated Carbons. Nihon Enerugi Gakkaishi/J. Jpn. Inst. Energy 2007, 86, 707–711. [Google Scholar] [CrossRef]
  98. Di Gregorio, F.; Parrillo, F.; Salzano, E.; Cammarota, F.; Arena, U. Removal of Naphthalene by Activated Carbons from Hot Gas. Chem. Eng. J. 2016, 291, 244–253. [Google Scholar] [CrossRef]
  99. Liu, W.J.; Zeng, F.X.; Jiang, H.; Zhang, X.S. Preparation of High Adsorption Capacity Bio-Chars from Waste Biomass. Bioresour. Technol. 2011, 102, 8247–8252. [Google Scholar] [CrossRef]
  100. Phuphuakrat, T.; Namioka, T.; Yoshikawa, K. Tar Removal from Biomass Pyrolysis Gas in Two-Step Function of Decomposition and Adsorption. Appl. Energy 2010, 87, 2203–2211. [Google Scholar] [CrossRef]
  101. Paethanom, A.; Yoshikawa, K. Influence of Pyrolysis Temperature on Rice Husk Char Characteristics and Its Tar Adsorption Capability. Energies 2012, 5, 4941–4951. [Google Scholar] [CrossRef]
  102. Paethanom, A.; Nakahara, S.; Kobayashi, M.; Prawisudha, P.; Yoshikawa, K. Performance of Tar Removal by Absorption and Adsorption for Biomass Gasification. Fuel Process. Technol. 2012, 104, 144–154. [Google Scholar] [CrossRef]
  103. San Miguel, G.; Lambert, S.D.; Graham, N.J.D. The Regeneration of Field-Spent Granular-Activated Carbons. Water Res. 2001, 35, 2740–2748. [Google Scholar] [CrossRef]
  104. Carratalá-Abril, J.; Lillo-Ródenas, M.A.; Linares-Solano, A.; Cazorla-Amorós, D. Regeneration of Activated Carbons Saturated with Benzene or Toluene Using an Oxygen-Containing Atmosphere. Chem. Eng. Sci. 2010, 65, 2190–2198. [Google Scholar] [CrossRef]
  105. Abu El-Rub, Z.; Bramer, E.A.; Brem, G. Experimental Comparison of Biomass Chars with Other Catalysts for Tar Reduction. Fuel 2008, 87, 2243–2252. [Google Scholar] [CrossRef]
  106. Fuentes-Cano, D.; Gómez-Barea, A.; Nilsson, S.; Ollero, P. Decomposition Kinetics of Model Tar Compounds over Chars with Different Internal Structure to Model Hot Tar Removal in Biomass Gasification. Chem. Eng. J. 2013, 228, 1223–1233. [Google Scholar] [CrossRef]
  107. Klinghoffer, N.B.; Castaldi, M.J.; Nzihou, A. Catalyst Properties and Catalytic Performance of Char from Biomass Gasification. Ind. Eng. Chem. Res. 2012, 51, 13113–13122. [Google Scholar] [CrossRef]
  108. Chen, X.; Jiang, H.; Cui, D.; Lu, K.; Kong, X.; Cai, J.; Yu, S.; Zhang, X. Selectivity Regulation of Au/Titanate by Biochar Modification for Selective Oxidation of Benzyl Alcohol. Catalysts 2023, 13, 864. [Google Scholar] [CrossRef]
  109. Abedian-Dehaghani, N.; Sadjadi, S.; Heravi, M.M. Selenium and Nitrogen Co-Doped Biochar as an Efficient Metal-Free Catalyst for Oxidation of Aldehydes. J. Mol. Struct. 2022, 1264, 133237. [Google Scholar] [CrossRef]
  110. Pang, S.; Liu, F.; Zhang, Y.; Dong, Z.; Su, Q.; Wang, W.; Li, Z.; Zhou, F.; Wang, Y. Construction of Functional Superhydrophobic Biochars as Hydrogen Transfer Catalysts for Dehydrogenation of N-Heterocycles. ACS Sustain. Chem. Eng. 2021, 9, 9062–9077. [Google Scholar] [CrossRef]
  111. Longo, L.; Taghavi, S.; Riello, M.; Ghedini, E.; Menegazzo, F.; Di Michele, A.; Cruciani, G.; Signoretto, M. Waste Biomasses as Precursors of Catalytic Supports in Benzaldehyde Hydrogenation. Catal. Today 2023, 420, 114038. [Google Scholar] [CrossRef]
  112. Kadam, H.K.; Tilve, S.G. Advancement in Methodologies for Reduction of Nitroarenes. RSC Adv. 2015, 5, 83391–83407. [Google Scholar] [CrossRef]
  113. Kumar, A.; Goyal, V.; Sarki, N.; Singh, B.; Ray, A.; Bhaskar, T.; Bordoloi, A.; Narani, A.; Natte, K. Biocarbon Supported Nanoscale Ruthenium Oxide-Based Catalyst for Clean Hydrogenation of Arenes and Heteroarenes. ACS Sustain. Chem. Eng. 2020, 8, 15740–15754. [Google Scholar] [CrossRef]
  114. Sadjadi, S.; Heravi, M.M.; Ghoreyshi Kahangi, F. Salep as a Biological Source for the Synthesis of Biochar with Utility for the Catalysis. Appl. Organomet. Chem. 2019, 33, e4990. [Google Scholar] [CrossRef]
  115. Sadjadi, S.; Akbari, M.; Léger, B.; Monflier, E.; Heravi, M.M. Eggplant-Derived Biochar-Halloysite Nanocomposite as Supports of Pd Nanoparticles for the Catalytic Hydrogenation of Nitroarenes in the Presence of Cyclodextrin. ACS Sustain. Chem. Eng. 2019, 7, 6720–6731. [Google Scholar] [CrossRef]
  116. Moradi, P.; Hajjami, M.; Tahmasbi, B. Fabricated Copper Catalyst on Biochar Nanoparticles for the Synthesis of Tetrazoles as Antimicrobial Agents. Polyhedron 2020, 175, 114169. [Google Scholar] [CrossRef]
  117. Ren, X.; Tang, L.; Wang, J.; Almatrafi, E.; Feng, H.; Tang, X.; Yu, J.; Yang, Y.; Li, X.; Zhou, C.; et al. Highly Efficient Catalytic Hydrogenation of Nitrophenols by Sewage Sludge Derived Biochar. Water Res. 2021, 201, 117360. [Google Scholar] [CrossRef]
  118. Wang, Y.; Shao, Y.; Zhang, L.; Zhang, S.; Wang, Y.; Xiang, J.; Hu, S.; Hu, G.; Hu, X. Co-Presence of Hydrophilic and Hydrophobic Sites in Ni/Biochar Catalyst for Enhancing the Hydrogenation Activity. Fuel 2021, 293, 120426. [Google Scholar] [CrossRef]
  119. Wang, Y.Y.; Ling, L.L.; Jiang, H. Selective Hydrogenation of Lignin to Produce Chemical Commodities by Using a Biochar Supported Ni-Mo2C Catalyst Obtained from Biomass. Green Chem. 2016, 18, 4032–4041. [Google Scholar] [CrossRef]
  120. Zhang, Q.; Xu, S.; Cao, Y.; Ruan, R.; Clark, J.H.; Hu, C.; Tsang, D.C.W. Sustainable Production of Gluconic Acid and Glucuronic Acid via Microwave-Assisted Glucose Oxidation over Low-Cost Cu-Biochar Catalysts. Green Chem. 2022, 24, 6657–6670. [Google Scholar] [CrossRef]
  121. Bardestani, R.; Biriaei, R.; Kaliaguine, S. Hydrogenation of Furfural to Furfuryl Alcohol over Ru Particles Supported on Mildly Oxidized Biochar. Catalysts 2020, 10, 934. [Google Scholar] [CrossRef]
  122. Fuente-Hernández, A.; Lee, R.; Béland, N.; Zamboni, I.; Lavoie, J.M. Reduction of Furfural to Furfuryl Alcohol in Liquid Phase over a Biochar-Supported Platinum Catalyst. Energies 2017, 10, 286. [Google Scholar] [CrossRef]
  123. Ameta, R.; Solanki, M.S.; Benjamin, S.; Ameta, S.C. Photocatalysis. In Advanced Oxidation Processes for Wastewater Treatment: Emerging Green Chemical Technology; Elsevier Inc.: Amsterdam, The Netherlands, 2018; pp. 135–175. ISBN 9780128105252. [Google Scholar]
  124. Wang, H.; Zhang, J.; Yuan, X.; Jiang, L.; Xia, Q.; Chen, H. Photocatalytic Removal of Antibiotics from Natural Water Matrices and Swine Wastewater via Cu(I) Coordinately Polymeric Carbon Nitride Framework. Chem. Eng. J. 2020, 392, 123638. [Google Scholar] [CrossRef]
  125. Liu, W.; Ni, J.; Yin, X. Synergy of Photocatalysis and Adsorption for Simultaneous Removal of Cr(VI) and Cr(III) with TiO2 and Titanate Nanotubes. Water Res. 2014, 53, 12–25. [Google Scholar] [CrossRef]
  126. Byrne, C.; Subramanian, G.; Pillai, S.C. Recent Advances in Photocatalysis for Environmental Applications. J. Environ. Chem. Eng. 2018, 6, 3531–3555. [Google Scholar] [CrossRef]
  127. Jeon, J.P.; Kweon, D.H.; Jang, B.J.; Ju, M.J.; Baek, J.B. Enhancing the Photocatalytic Activity of TiO2 Catalysts. Adv. Sustain. Syst. 2020, 4, 2000197. [Google Scholar] [CrossRef]
  128. Li, D.; Fang, Y.; Lu, J.; Sun, J.; Zhao, X.; Hou, N.; Xing, J. Enhanced Biodegradation of PAHs by Biochar and a TiO2@biochar Composite under Light Irradiation: Photocatalytic Mechanism, Toxicity Evaluation and Ecological Response. Chem. Eng. J. 2023, 458, 141495. [Google Scholar] [CrossRef]
  129. Wang, J.; Wang, G.; Yu, T.; Ding, N.; Wang, M.; Chen, Y. Photocatalytic Performance of Biochar-Modified TiO2 (C/TiO2) for Ammonia-Nitrogen Removal. RSC Adv. 2023, 13, 24237–24249. [Google Scholar] [CrossRef]
  130. Hou, N.; Li, X.; Jiang, X.; Zhang, N.; Wang, R.; Li, D. The Role of Biochar in the Photocatalytic Treatment of a Mixture of Cr(VI) and Phenol Pollutants: Biochar as a Carrier for Transferring and Storing Electrons. Sci. Total Environ. 2022, 844, 157145. [Google Scholar] [CrossRef]
  131. Wang, B.; Liu, B.; Ji, X.X.; Ma, M.G. Synthesis, Characterization, and Photocatalytic Properties of Bamboo Charcoal/TiO2 Composites Using Four Sizes Powder. Materials 2018, 11, 670. [Google Scholar] [CrossRef]
  132. Mao, W.; Zhang, L.; Liu, Y.; Wang, T.; Bai, Y.; Guan, Y. Facile Assembled N, S-Codoped Corn Straw Biochar Loaded Bi2WO6 with the Enhanced Electron-Rich Feature for the Efficient Photocatalytic Removal of Ciprofloxacin and Cr(VI). Chemosphere 2021, 263, 127988. [Google Scholar] [CrossRef]
  133. Sun, L.; Qi, Y.; Jia, C.J.; Jin, Z.; Fan, W. Enhanced Visible-Light Photocatalytic Activity of g-C3N4/Zn2GeO4 Heterojunctions with Effective Interfaces Based on Band Match. Nanoscale 2014, 6, 2649–2659. [Google Scholar] [CrossRef]
  134. Meng, L.; Yin, W.; Wang, S.; Wu, X.; Hou, J.; Yin, W.; Feng, K.; Ok, Y.S.; Wang, X. Photocatalytic Behavior of Biochar-Modified Carbon Nitride with Enriched Visible-Light Reactivity. Chemosphere 2020, 239, 124713. [Google Scholar] [CrossRef] [PubMed]
  135. Li, F.; Lin, M. Synthesis of Biochar-Supported K-Doped G-C3N4 Photocatalyst for Enhancing the Polycyclic Aromatic Hydrocarbon Degradation Activity. Int. J. Environ. Res. Public. Health 2020, 17, 2065. [Google Scholar] [CrossRef] [PubMed]
  136. Xiao, Y.; Lyu, H.; Tang, J.; Wang, K.; Sun, H. Effects of Ball Milling on the Photochemistry of Biochar: Enrofloxacin Degradation and Possible Mechanisms. Chem. Eng. J. 2020, 384, 123311. [Google Scholar] [CrossRef]
  137. Mora-Hernandez, J.M.; Huerta-Flores, A.M.; Torres-Martínez, L.M. Photoelectrocatalytic Characterization of Carbon-Doped NaTaO3 Applied in the Photoreduction of CO2 towards the Formaldehyde Production. J. CO2 Util. 2018, 27, 179–187. [Google Scholar] [CrossRef]
  138. Sun, S.; Watanabe, M.; Wu, J.; An, Q.; Ishihara, T. Ultrathin WO3·0.33H2O Nanotubes for CO2 Photoreduction to Acetate with High Selectivity. J. Am. Chem. Soc. 2018, 140, 6474–6482. [Google Scholar] [CrossRef] [PubMed]
  139. Liu, L.; Du, S.; Guo, X.; Xiao, Y.; Yin, Z.; Yang, N.; Bao, Y.; Zhu, X.; Jin, S.; Feng, Z.; et al. Water-Stable Nickel Metal-Organic Framework Nanobelts for Cocatalyst-Free Photocatalytic Water Splitting to Produce Hydrogen. J. Am. Chem. Soc. 2022, 144, 2747–2754. [Google Scholar] [CrossRef]
  140. Lin, F.; Gao, M.; Wang, Y.; Yu, J.; Gao, C.; Zang, S. Enhanced Mass Transfer with Amphiphilic CoOx/Biochar for Photocatalytic CO2 Conversion. Appl. Surf. Sci. 2022, 605, 154612. [Google Scholar] [CrossRef]
  141. Yang, J.; Gao, G.; Zhu, Z.; Yu, X. Biochar Modified Co–Al LDH for Enhancing Photocatalytic Reduction CO2 Performance and Mechanism Insight. Res. Chem. Intermed. 2022, 48, 2313–2323. [Google Scholar] [CrossRef]
  142. Bhavani, P.; Praveen Kumar, D.; Hussain, M.; Aminabhavi, T.M.; Park, Y.K. Eco-Friendly Rice Husk Derived Biochar as a Highly Efficient Noble Metal-Free Cocatalyst for High Production of H2 Using Solar Light Irradiation. Chem. Eng. J. 2022, 434, 134743. [Google Scholar] [CrossRef]
  143. O’Hayre, R.; Cha, S.; Colella, W.; Prinz, F.B. Fuel Cell Fundamentals; Wiley: Hoboken, NJ, USA, 2016; ISBN 9781119113805. [Google Scholar]
  144. Wang, J.; Kong, H.; Zhang, J.; Hao, Y.; Shao, Z.; Ciucci, F. Carbon-Based Electrocatalysts for Sustainable Energy Applications. Prog. Mater. Sci. 2021, 116, 100717. [Google Scholar] [CrossRef]
  145. Serp, P.; Figueiredo, J.L. (Eds.) Carbon Materials for Catalysis; Wiley: Hoboken, NJ, USA, 2008; ISBN 9780470178850. [Google Scholar]
  146. Jiang, H.; Gu, J.; Zheng, X.; Liu, M.; Qiu, X.; Wang, L.; Li, W.; Chen, Z.; Ji, X.; Li, J. Defect-Rich and Ultrathin N Doped Carbon Nanosheets as Advanced Trifunctional Metal-Free Electrocatalysts for the ORR, OER and HER. Energy Environ. Sci. 2019, 12, 322–333. [Google Scholar] [CrossRef]
  147. Hu, C.; Dai, L. Carbon-Based Metal-Free Catalysts for Electrocatalysis beyond the ORR. Angew. Chem. Int. Ed. 2016, 55, 11736–11758. [Google Scholar] [CrossRef] [PubMed]
  148. Sun, X.; Wang, R.; Su, D. Research Progress in Metal-Free Carbon-Based Catalysts. Cuihua Xuebao/Chin. J. Catal. 2013, 34, 508–523. [Google Scholar] [CrossRef]
  149. Zhu, Y.; Murali, S.; Cai, W.; Li, X.; Suk, J.W.; Potts, J.R.; Ruoff, R.S. Graphene and Graphene Oxide: Synthesis, Properties, and Applications. Adv. Mater. 2010, 22, 3906–3924. [Google Scholar] [CrossRef]
  150. Zhou, L.; Fu, P.; Wen, D.; Yuan, Y.; Zhou, S. Self-Constructed Carbon Nanoparticles-Coated Porous Biocarbon from Plant Moss as Advanced Oxygen Reduction Catalysts. Appl. Catal. B 2016, 181, 635–643. [Google Scholar] [CrossRef]
  151. Huang, B.; Liu, Y.; Xie, Z. Biomass Derived 2D Carbons via a Hydrothermal Carbonization Method as Efficient Bifunctional ORR/HER Electrocatalysts. J. Mater. Chem. A Mater. 2017, 5, 23481–23488. [Google Scholar] [CrossRef]
  152. Li, C.; Zhao, X.; Gao, M.; Kong, F.; Chen, H. Effectively Controlled Structures of Si-C Composites from Rice Husk for Oxygen Evolution Catalyst. Molecules 2023, 28, 6117. [Google Scholar] [CrossRef] [PubMed]
  153. Mijowska, E.; Pietrusewicz, K.; Maślana, K. Highly Porous Carbon Flakes Derived from Cellulose and Nickel Phosphide Heterostructure towards Efficient Electrocatalysis of Oxygen Evolution Reaction. Molecules 2024, 29, 352. [Google Scholar] [CrossRef] [PubMed]
  154. Zhang, Y.; Zhang, X.; Ma, X.; Guo, W.; Wang, C.; Asefa, T.; He, X. A Facile Synthesis of Nitrogen-Doped Highly Porous Carbon Nanoplatelets: Efficient Catalysts for Oxygen Electroreduction. Sci. Rep. 2017, 7, 43366. [Google Scholar] [CrossRef]
  155. Xuan, C.; Wu, Z.; Lei, W.; Wang, J.; Guo, J.; Wang, D. Nitrogen-Doped Hierarchical Porous Carbons Derived from Sodium Alginate as Efficient Oxygen Reduction Reaction Electrocatalysts. ChemCatChem 2017, 9, 809–815. [Google Scholar] [CrossRef]
  156. Mulyadi, A.; Zhang, Z.; Dutzer, M.; Liu, W.; Deng, Y. Facile Approach for Synthesis of Doped Carbon Electrocatalyst from Cellulose Nanofibrils toward High-Performance Metal-Free Oxygen Reduction and Hydrogen Evolution. Nano Energy 2017, 32, 336–346. [Google Scholar] [CrossRef]
  157. Choi, I.A.; Kwak, D.H.; Han, S.B.; Park, J.Y.; Park, H.S.; Ma, K.B.; Kim, D.H.; Won, J.E.; Park, K.W. Doped Porous Carbon Nanostructures as Non-Precious Metal Catalysts Prepared by Amino Acid Glycine for Oxygen Reduction Reaction. Appl. Catal. B Environ. 2017, 211, 235–244. [Google Scholar] [CrossRef]
  158. Mustakeem. Electrode Materials for Microbial Fuel Cells: Nanomaterial Approach. Mater. Renew. Sustain. Energy 2015, 4, 22. [Google Scholar] [CrossRef]
  159. Apollon, W. An Overview of Microbial Fuel Cell Technology for Sustainable Electricity Production. Membranes 2023, 13, 884. [Google Scholar] [CrossRef]
  160. Kalathil, S.; Patil, S.A.; Pant, D. Microbial Fuel Cells: Electrode Materials. In Encyclopedia of Interfacial Chemistry; Elsevier: Amsterdam, The Netherlands, 2018; pp. 309–318. [Google Scholar]
  161. Li, S.; Cheng, C.; Thomas, A. Carbon-Based Microbial-Fuel-Cell Electrodes: From Conductive Supports to Active Catalysts. Adv. Mater. 2017, 29, 1602547. [Google Scholar] [CrossRef] [PubMed]
  162. Liu, H.; Cheng, S.; Logan, B.E. Power Generation in Fed-Batch Microbial Fuel Cells as a Function of Ionic Strength, Temperature, and Reactor Configuration. Environ. Sci. Technol. 2005, 39, 5488–5493. [Google Scholar] [CrossRef] [PubMed]
  163. Chaudhuri, S.K.; Lovley, D.R. Electricity Generation by Direct Oxidation of Glucose in Mediatorless Microbial Fuel Cells. Nat. Biotechnol. 2003, 21, 1229–1232. [Google Scholar] [CrossRef] [PubMed]
  164. Logan, B.; Cheng, S.; Watson, V.; Estadt, G. Graphite Fiber Brush Anodes for Increased Power Production in Air-Cathode Microbial Fuel Cells. Environ. Sci. Technol. 2007, 41, 3341–3346. [Google Scholar] [CrossRef] [PubMed]
  165. Ahn, Y.; Logan, B.E. Effectiveness of Domestic Wastewater Treatment Using Microbial Fuel Cells at Ambient and Mesophilic Temperatures. Bioresour. Technol. 2010, 101, 469–475. [Google Scholar] [CrossRef] [PubMed]
  166. Wang, X.; Feng, Y.J.; Lee, H. Electricity Production from Beer Brewery Wastewater Using Single Chamber Microbial Fuel Cell. Water Sci. Technol. 2008, 57, 1117–1121. [Google Scholar] [CrossRef] [PubMed]
  167. Wang, Z.; Zheng, Z.; Zheng, S.; Chen, S.; Zhao, F. Carbonized Textile with Free-Standing Threads as an Efficient Anode Material for Bioelectrochemical Systems. J. Power Sources 2015, 287, 269–275. [Google Scholar] [CrossRef]
  168. Iijima, S. Helical Microtubules of Graphitic Carbon. Nature 1991, 354, 56–58. [Google Scholar] [CrossRef]
  169. Correa-Duarte, M.A.; Wagner, N.; Rojas-Chapana, J.; Morsczeck, C.; Thie, M.; Giersig, M. Fabrication and Biocompatibility of Carbon Nanotube-Based 3D Networks as Scaffolds for Cell Seeding and Growth. Nano Lett. 2004, 4, 2233–2236. [Google Scholar] [CrossRef]
  170. Heister, E.; Brunner, E.W.; Dieckmann, G.R.; Jurewicz, I.; Dalton, A.B. Are Carbon Nanotubes a Natural Solution? Applications in Biology and Medicine. ACS Appl. Mater. Interfaces 2013, 5, 1870–1891. [Google Scholar] [CrossRef]
  171. Erbay, C.; Pu, X.; Choi, W.; Choi, M.J.; Ryu, Y.; Hou, H.; Lin, F.; De Figueiredo, P.; Yu, C.; Han, A. Control of Geometrical Properties of Carbon Nanotube Electrodes towards High-Performance Microbial Fuel Cells. J. Power Sources 2015, 280, 347–354. [Google Scholar] [CrossRef]
  172. Tsai, H.Y.; Wu, C.C.; Lee, C.Y.; Shih, E.P. Microbial Fuel Cell Performance of Multiwall Carbon Nanotubes on Carbon Cloth as Electrodes. J. Power Sources 2009, 194, 199–205. [Google Scholar] [CrossRef]
  173. Zhou, M.; Chi, M.; Luo, J.; He, H.; Jin, T. An Overview of Electrode Materials in Microbial Fuel Cells. J. Power Sources 2011, 196, 4427–4435. [Google Scholar] [CrossRef]
  174. Qiao, Y.; Li, C.M.; Bao, S.J.; Bao, Q.L. Carbon Nanotube/Polyaniline Composite as Anode Material for Microbial Fuel Cells. J. Power Sources 2007, 170, 79–84. [Google Scholar] [CrossRef]
  175. Sharma, T.; Mohana Reddy, A.L.; Chandra, T.S.; Ramaprabhu, S. Development of Carbon Nanotubes and Nanofluids Based Microbial Fuel Cell. Int. J. Hydrogen Energy 2008, 33, 6749–6754. [Google Scholar] [CrossRef]
  176. Zou, Y.; Xiang, C.; Yang, L.; Sun, L.X.; Xu, F.; Cao, Z. A Mediatorless Microbial Fuel Cell Using Polypyrrole Coated Carbon Nanotubes Composite as Anode Material. Int. J. Hydrogen Energy 2008, 33, 4856–4862. [Google Scholar] [CrossRef]
  177. Zhu, K.; Xu, Y.; Yang, X.; Fu, W.; Dang, W.; Yuan, J.; Wang, Z. Sludge Derived Carbon Modified Anode in Microbial Fuel Cell for Performance Improvement and Microbial Community Dynamics. Membranes 2022, 12, 120. [Google Scholar] [CrossRef]
  178. Deng, Y.; Zhao, R. Advanced Oxidation Processes (AOPs) in Wastewater Treatment. Curr. Pollut. Rep. 2015, 1, 167–176. [Google Scholar] [CrossRef]
  179. Ma, D.; Yi, H.; Lai, C.; Liu, X.; Huo, X.; An, Z.; Li, L.; Fu, Y.; Li, B.; Zhang, M.; et al. Critical Review of Advanced Oxidation Processes in Organic Wastewater Treatment. Chemosphere 2021, 275, 130104. [Google Scholar] [CrossRef] [PubMed]
  180. Rekhate, C.V.; Srivastava, J.K. Recent Advances in Ozone-Based Advanced Oxidation Processes for Treatment of Wastewater—A Review. Chem. Eng. J. Adv. 2020, 3, 100031. [Google Scholar] [CrossRef]
  181. Tian, S.Q.; Qi, J.Y.; Wang, Y.P.; Liu, Y.L.; Wang, L.; Ma, J. Heterogeneous Catalytic Ozonation of Atrazine with Mn-Loaded and Fe-Loaded Biochar. Water Res. 2021, 193, 116860. [Google Scholar] [CrossRef] [PubMed]
  182. Chen, C.; Yan, X.; Xu, Y.Y.; Yoza, B.A.; Wang, X.; Kou, Y.; Ye, H.; Wang, Q.; Li, Q.X. Activated Petroleum Waste Sludge Biochar for Efficient Catalytic Ozonation of Refinery Wastewater. Sci. Total Environ. 2019, 651, 2631–2640. [Google Scholar] [CrossRef] [PubMed]
  183. Cheng, Y.; Wang, B.; Yan, P.; Shen, J.; Kang, J.; Zhao, S.; Zhu, X.; Shen, L.; Wang, S.; Shen, Y.; et al. In-Situ Formation of Surface Reactive Oxygen Species on Defective Sites over N-Doped Biochar in Catalytic Ozonation. Chem. Eng. J. 2023, 454, 140232. [Google Scholar] [CrossRef]
  184. Cha, J.S.; Kim, Y.M.; Lee, I.H.; Choi, Y.J.; Rhee, G.H.; Song, H.; Jeon, B.H.; Lam, S.S.; Khan, M.A.; Andrew Lin, K.Y.; et al. Mitigation of Hazardous Toluene via Ozone-Catalyzed Oxidation Using MnOx/Sawdust Biochar Catalyst. Environ. Pollut. 2022, 312, 119920. [Google Scholar] [CrossRef]
  185. Babuponnusami, A.; Muthukumar, K. A Review on Fenton and Improvements to the Fenton Process for Wastewater Treatment. J. Environ. Chem. Eng. 2014, 2, 557–572. [Google Scholar] [CrossRef]
  186. Esteves, B.M.; Morales-Torres, S.; Maldonado-Hódar, F.J.; Madeira, L.M. Fitting Biochars and Activated Carbons from Residues of the Olive Oil Industry as Supports of Fe-Catalysts for the Heterogeneous Fenton-like Treatment of Simulated Olive Mill Wastewater. Nanomaterials 2020, 10, 876. [Google Scholar] [CrossRef] [PubMed]
  187. Jian, H.; Yang, F.; Gao, Y.; Zhen, K.; Tang, X.; Zhang, P.; Wang, Y.; Wang, C.; Sun, H. Efficient Removal of Pyrene by Biochar Supported Iron Oxide in Heterogeneous Fenton-like Reaction via Radicals and High-Valent Iron-Oxo Species. Sep. Purif. Technol. 2021, 265, 118518. [Google Scholar] [CrossRef]
  188. Faheem; Du, J.; Hoon Kim, S.; Azher Hassan, M.; Irshad, S.; Bao, J. Application of Biochar in Advanced Oxidation Processes: Supportive, Adsorptive, and Catalytic Role. Environ. Sci. Pollut. Res. 2020, 27, 37286–37312. [Google Scholar] [CrossRef] [PubMed]
  189. Zhu, K.; Wang, X.; Geng, M.; Chen, D.; Lin, H.; Zhang, H. Catalytic Oxidation of Clofibric Acid by Peroxydisulfate Activated with Wood-Based Biochar: Effect of Biochar Pyrolysis Temperature, Performance and Mechanism. Chem. Eng. J. 2019, 374, 1253–1263. [Google Scholar] [CrossRef]
  190. He, L.; Liu, Z.; Hu, J.; Qin, C.; Yao, L.; Zhang, Y.; Piao, Y. Sugarcane Biochar as Novel Catalyst for Highly Efficient Oxidative Removal of Organic Compounds in Water. Chem. Eng. J. 2021, 405, 126895. [Google Scholar] [CrossRef]
  191. Guo, Z.; Bai, G.; Huang, B.; Cai, N.; Guo, P.; Chen, L. Preparation and Application of a Novel Biochar-Supported Red Mud Catalyst: Active Sites and Catalytic Mechanism. J. Hazard. Mater. 2021, 408, 124802. [Google Scholar] [CrossRef]
Figure 1. Biodiesel yield (%) obtained at various reaction temperatures (°C) of biochar woodchip. Reproduced from [71].
Figure 1. Biodiesel yield (%) obtained at various reaction temperatures (°C) of biochar woodchip. Reproduced from [71].
Materials 17 00565 g001
Figure 2. The results of tar reforming over the three selected carbon materials. (a) Tar yields measured; (b) weight gain and the rate of tar reforming. Reproduced from [94].
Figure 2. The results of tar reforming over the three selected carbon materials. (a) Tar yields measured; (b) weight gain and the rate of tar reforming. Reproduced from [94].
Materials 17 00565 g002
Figure 3. Specific surface area values for the BET analysis of rice husk and rice husk chars. Reproduced from [101].
Figure 3. Specific surface area values for the BET analysis of rice husk and rice husk chars. Reproduced from [101].
Materials 17 00565 g003
Figure 4. The conversion (a) and selectivity (b) of 6 h and 12 h oxidation reactions of air-calcined catalysts at 400 °C. Reproduced from [108].
Figure 4. The conversion (a) and selectivity (b) of 6 h and 12 h oxidation reactions of air-calcined catalysts at 400 °C. Reproduced from [108].
Materials 17 00565 g004
Figure 5. (a) Conversion and (b) selectivity to FA at 210 °C (columns 1–3) and at 320 °C (columns 4–6). Reproduced from [122].
Figure 5. (a) Conversion and (b) selectivity to FA at 210 °C (columns 1–3) and at 320 °C (columns 4–6). Reproduced from [122].
Materials 17 00565 g005
Figure 6. Photocatalytic degradation of MB using the samples (A) under UV irradiation and (B) under visible irradiation. Reproduced from [131].
Figure 6. Photocatalytic degradation of MB using the samples (A) under UV irradiation and (B) under visible irradiation. Reproduced from [131].
Materials 17 00565 g006
Figure 7. (a) Photocatalytic degradation curve of naphthalene and (b) the corresponding apparent rate constants (1—K + g-C3N4; 2—biochar/K + g-C3N4 1:0.8; 3—biochar/K + g-C3N4 1:1; and 4—biochar/K + g-C3N4 1:1.2). Reproduced from [135].
Figure 7. (a) Photocatalytic degradation curve of naphthalene and (b) the corresponding apparent rate constants (1—K + g-C3N4; 2—biochar/K + g-C3N4 1:0.8; 3—biochar/K + g-C3N4 1:1; and 4—biochar/K + g-C3N4 1:1.2). Reproduced from [135].
Materials 17 00565 g007
Figure 8. (a) LSV (measuring the current response as a function of the applied potential) and (b) Tafel plots of RuO2, Ni12P5, and Ni12P5_cellulose composites. Reproduced from [153].
Figure 8. (a) LSV (measuring the current response as a function of the applied potential) and (b) Tafel plots of RuO2, Ni12P5, and Ni12P5_cellulose composites. Reproduced from [153].
Materials 17 00565 g008
Figure 9. Schematic representation of a typical MFC process. Reproduced from [141].
Figure 9. Schematic representation of a typical MFC process. Reproduced from [141].
Materials 17 00565 g009
Figure 10. (a) The efficiency in COD removal by MFCs; (b) the ratio of volatile suspended solids/total suspended solids in the inoculated anaerobic granular sludge within MFC systems; (c) polarization curves; and (d) the power density of MFCs. Reproduced from [177].
Figure 10. (a) The efficiency in COD removal by MFCs; (b) the ratio of volatile suspended solids/total suspended solids in the inoculated anaerobic granular sludge within MFC systems; (c) polarization curves; and (d) the power density of MFCs. Reproduced from [177].
Materials 17 00565 g010
Figure 11. Comparison of phenolic compound removal via adsorption of catalytic wet peroxide oxidation (CWPO) using OSC-AC-FE and N-Fe catalysts: (a) Adsorption for OSC-AC-Fe; (b) CWPO for OSC-AC-Fe; (c) Adsorption for N-Fe; (d) CWPO for N-Fe. Reproduced from [186].
Figure 11. Comparison of phenolic compound removal via adsorption of catalytic wet peroxide oxidation (CWPO) using OSC-AC-FE and N-Fe catalysts: (a) Adsorption for OSC-AC-Fe; (b) CWPO for OSC-AC-Fe; (c) Adsorption for N-Fe; (d) CWPO for N-Fe. Reproduced from [186].
Materials 17 00565 g011
Table 1. Carbonaceous materials are obtained from biomass through different treatments and their applications.
Table 1. Carbonaceous materials are obtained from biomass through different treatments and their applications.
Biomass/WasteCarbonaceous MaterialTreatmentApplicationReference
Coconut coir dustHighly curved graphite structuresHTC + PyrolysisVarious[45]
Cinnamomum camphora leavesGraphenePyrolysisVarious[46]
Perilla frutescens leavesO/N-co-doped porous carbon nanosheetsPyrolysisElectrode materials for supercapacitors[47]
Watermelon pulpCarbon-based composite powder (micrometer particles and nanosheets)HTCAnode materials of lithium-ion batteries[48]
CelluloseGraphitic carbon nanostructuresHTC + ImpregnationFuel cell catalytic supports/anodes in Li-ion batteries.[49]
Brassica juncea L. plantsCarbon nanotubesExtraction + thermal treatmentPhotocatalysts[50]
SawdustNanofibers/mesoporous carbon compositesCatalytic pyrolysisElectrode materials for electrochemical energy storage[51]
Spruce barkGraphene nanosheet arraysHTC + KOH activationElectrode material for supercapacitors[52]
Rice huskGraphene-like materialsThermal treatment + KOH activationGraphene materials to improve cement mortar strength [53]
Sphagnum moss, corn stalks, cotton, and prickly bambooCarbon nanotubesPyrolysis + mechanochemical activationHydrogen storage[54]
CottonMultilayer carbon nanotubesPyrolysis + mechanochemical activationAdsorbent[55]
Sugarcane bagasseGraphene-like nanosheetsCarbonization + KOH activationSupercapacitors[56]
Rice strawCarbon nanotubesChemical pretreatment + HTCCatalyst supports[57]
Softwood sawdustGraphitic nanotubesChemical pretreatment + pyrolysisElectrode or filtration applications[58]
Sugarcane bagasseNanostructured biocharMicrowave-assisted pyrolysisVarious[59]
Wheat strawGraphene sheetsHTC + graphitization Anode material for lithium-ion batteries[60]
Coconut shellPorous graphene-like nanosheetsChemical activation + pyrolysisSupercapacitor[61]
Almond shellBiocharPyrolysisElectrode in microbial electrolysis cell[62]
Peanut dregsPorous carbon materialPyrolysis + chemical activationMultiple energy storage applications[63]
Sugar caneGraphene-like materialPyrolysis + chemical activationAdsorbent [64]
LigninLayered graphene-like structureChemical solution combustionAdsorbent[65]
Table 2. Comparison of different biochar-derived catalysts.
Table 2. Comparison of different biochar-derived catalysts.
ReactionCatalystConditionsCatalytic EfficiencyRef.
Biodiesel SynthesisNiO-MoO/biochar75 °C, 60 min77% yield[71]
Biodiesel SynthesisCaO/biochar100 °C, 180 min91% yield[72]
Biodiesel SynthesisCaO-SiO2/biochar65 °C, 150 min94% yield[73]
Biodiesel SynthesisBiochar60 °C, 120 min98% yield[74]
Biodiesel SynthesisSulfonated biochar80 °C, 40 min100% yield[75]
Biodiesel SynthesisSulfonated biochar65 °C, 60 min82% yield[67]
Biodiesel SynthesisSulfonated biochar65 °C, 360 min99% yield[76]
FTSCo/biochar500 °C, 2 MPa67% conversion[79]
FTSN-doped biochar300 °C, 2 MPa92% conversion[80]
FTSFe/biochar300 °C, 2 MPa46.7% conversion[81]
DRMBiochar900 W (MW)75% CH4 conversion[84]
DRMBiochar900 °C65% CH4 conversion[85]
Table 3. Comparison of different biochar-derived catalyst performances regarding AOP, catalyst, yield, and removal efficiency.
Table 3. Comparison of different biochar-derived catalyst performances regarding AOP, catalyst, yield, and removal efficiency.
AOPCatalystPollutantRemoval EfficiencyRef.
OzonationMnOx/biocharTrizine34%[181]
FeOx/biochar35%
OzonationBiocharRefineries residues80%[182]
OzonationBiocharAtrazine74%[183]
OzonationMnOx/biocharToluene90%[184]
Fenton processFe/biocharOlive mill wastewater92%[186]
Fenton processFe3O4/biocharPyrene100%[187]
PDS activationBiocharClofibric acid98%[189]
PMS activationBiocharBisphenol A100%[190]
PDS activationFe/biocharOrange 7100%[191]
Disclaimer/Publisher’s Note: The statements, opinions and data contained in all publications are solely those of the individual author(s) and contributor(s) and not of MDPI and/or the editor(s). MDPI and/or the editor(s) disclaim responsibility for any injury to people or property resulting from any ideas, methods, instructions or products referred to in the content.

Share and Cite

MDPI and ACS Style

Villora-Picó, J.J.; González-Arias, J.; Baena-Moreno, F.M.; Reina, T.R. Renewable Carbonaceous Materials from Biomass in Catalytic Processes: A Review. Materials 2024, 17, 565. https://doi.org/10.3390/ma17030565

AMA Style

Villora-Picó JJ, González-Arias J, Baena-Moreno FM, Reina TR. Renewable Carbonaceous Materials from Biomass in Catalytic Processes: A Review. Materials. 2024; 17(3):565. https://doi.org/10.3390/ma17030565

Chicago/Turabian Style

Villora-Picó, Juan J., Judith González-Arias, Francisco M. Baena-Moreno, and Tomás R. Reina. 2024. "Renewable Carbonaceous Materials from Biomass in Catalytic Processes: A Review" Materials 17, no. 3: 565. https://doi.org/10.3390/ma17030565

Note that from the first issue of 2016, this journal uses article numbers instead of page numbers. See further details here.

Article Metrics

Back to TopTop