Next Article in Journal
Fully Integrated Hybrid Solid Oxide Fuel Cell–Rankine Cycle System with Carbon Capture, Utilisation, and Storage for Sustainable Combined Heat and Power Production
Next Article in Special Issue
Quantifying the Impact of Coal Transition on GDP Growth through System Dynamics: The Case of the Region of Western Macedonia, Greece
Previous Article in Journal
Citizens’ Perception of Blockchain-Based E-Voting Systems: Focusing on TAM
Previous Article in Special Issue
How Does Environmental Protection Tax Affect Urban Energy Consumption in China? New Insights from the Intensity Difference-in-Differences Model
 
 
Font Type:
Arial Georgia Verdana
Font Size:
Aa Aa Aa
Line Spacing:
Column Width:
Background:
Review

Implementation of Renewable Energy from Solar Photovoltaic (PV) Facilities in Peru: A Promising Sustainable Future

by
Carlos Cacciuttolo
1,*,
Ximena Guardia
2 and
Eunice Villicaña
2,*
1
Department of Civil Works and Geology, Catholic University of Temuco, Temuco 4780000, Chile
2
Ingeniería de la Energía, Universidad de Ingeniería y Tecnología (UTEC), Lima 15063, Peru
*
Authors to whom correspondence should be addressed.
Sustainability 2024, 16(11), 4388; https://doi.org/10.3390/su16114388
Submission received: 26 March 2024 / Revised: 13 May 2024 / Accepted: 15 May 2024 / Published: 22 May 2024
(This article belongs to the Special Issue Energy and Environment: Policy, Economics and Modeling)

Abstract

:
In the last two decades, Peru has experienced a process of transformation in the sources of its energy matrix, increasing the participation of clean energy such as solar photovoltaic (PV), on-shore wind, biomass, and small hydro. However, hydropower and natural gas remain the main sources of electricity, whereas off-shore wind, biogas, waves, tidal, and geothermal sources are currently underdeveloped. This article presents the enormous potential of Peru for the generation of electrical energy from a solar source equivalent to 25 GW, as it has in one of the areas of the world with the highest solar radiation throughout the year. In addition, this article presents the main advantages, benefits, and considerations of the implementation of solar photovoltaic technology, with emphasis on (i) the potential of solar energy, showing the available potential and an installed capacity by the year 2024 equivalent to 398 MW, (ii) current solar energy sources, characterizing existing industrial solar photovoltaic (PV) energy plants, and (iii) future solar energy facilities projections, stating the portfolio of solar renewable energy plant projects to be implemented in the future considering an installed capacity of 7.2 GW by 2028. Additionally, lessons learned, challenges, and directions for the future development of solar energy in the country are presented. Finally, the article concludes that if Peru takes advantage of solar potential by considering a sustainable future perspective and implementing strategic land-use planning, the southern region will be transformed into a world-class territory for renewable energy development considering the hybridization of concentrated solar power (CSP) systems with solar photovoltaic (PV) systems and solar energy storage systems.

1. Introduction

1.1. Implementation of Renewable Energies in Peru

Peru is one of the most diverse countries on the planet, considering its geography, climate, ecosystems, and ancestral culture [1]. It is a country whose economy is characterized by having the following activities: (i) mining, being the second-highest world producer of copper; (ii) agriculture, being one of the world leaders in the export of organic fruits and vegetables without the use of genetically modified crops; (iii) fishing, being one of the world leaders in fishmeal exports; (iv) tourism, being known worldwide for its countless destinations, such as the city of Lima, Colca Valley, Titicaca Lake, Inca Sacred Valley, and the Inca city of Machu Picchu, among others; and (v) gastronomy, possessing some of the most diverse and tasty foods in the world. Its population is equivalent to approximately 33 million inhabitants, and it has a gross domestic product (GDP) of 222 $USD billion, with an annual economic growth rate of 2%, a human development index (HDI) equivalent to 0.759, and a per capita income equivalent to 6491 $USD. Peru is a place that offers adequate conditions to promote investment projects because social inclusion is respected, ecosystems are protected, and companies are allowed to generate value and employment under a regulatory framework based on sustainable development and human well-being [2].
According to the Ministry of Energy and Mines of Peru (MINEM), energy consumption in the country is estimated to increase by 10% annually, related mainly to industrial development [3]. Concerning data from the Economic Operation Committee of the National Interconnected Electricity System of Peru (COES–SEIN), the total electricity generated in 2012 was 37,617.6 GWh, while in 2022 it was 56,084.2 GWh, equivalent to a growth of 49.1% in comparison to 2012. This projection has persisted in recent times, mirroring the rise in electricity demand in Peru that drives the country’s robust economic, technological, and population expansion [4].
The increase in energy demand in Peru is monitored by the COES–SEIN, which projects the energy demand in the country for the short term (3 years) and long term (10 years) under different scenarios, predicts the amount of efficient energy required, and estimates the years when it would be needed and its location. Unfortunately, the COES is a private institution that provides guidance and possible solutions to the electricity system of the country, but it does not have a binding planning role [5].
According to the Supreme Decree N° 031-2007-EM, the General Directorate of Energy Efficiency of the Ministry of Energy and Mines is the regulatory technical body in charge of proposing and evaluating the policy for energy efficiency and renewable energies, as well as conducting energy planning. To date, the only measure for promoting the development of renewable energy technologies has been the promulgation of the Legislative Decree N° 1002 and its regulations approved by Supreme Decree N° 050-2008-EM and modified by Supreme Decree N° 012-2011-EM. This legal framework led to the execution of four auctions for renewable energy resources (RER) generation, assigning contracts to 64 solar, wind, biomass, and small hydroelectric power plant (less than 20 MW) projects for a total installed capacity of 1274 MW and one off-grid auction for the installation and maintenance of up to 500 thousand autonomous photovoltaic (PV) systems throughout the country [6].
By the end of 2023, Peru had a total installed capacity of 13,693.278 MW on its electricity matrix [5]. It generated 58,393.34 GWh/year from its three main natural gas reserves (42.7%), while 44% came from conventional renewable energy (hydropower), and only 9.9% came from non-conventional renewable energy resources (RER) like on-shore wind and solar photovoltaic (PV) [7].
On the other hand, in 2023, the maximum power demand in the country was 7605.51 MW in the National Interconnected Electrical System (SEIN), 86.2% of which was required in the central zone of Peru, where one-third of the population of the country lives mainly in urban zones (Lima, Huancayo, and Huaraz cities, among others). The north of Peru uses 7.31% of the energy, and the population lives mainly in urban zones (Piura, Chiclayo, and Trujillo cities, among others) and some rural zones (the Loreto, Tumbes, Piura, Lambayeque, San Martin, and Cajamarca regions, among others), and the south of Peru uses 6.48%, and the population lives mainly in urban zones (Arequipa, Puno, Tacna, and Cuzco cities, among others) and some rural zones (the Madre de Dios, Arequipa, Apurimac, Moquegua, and Tacna regions, among others) [5].
There is a key difference between the useful clean-energy potential and its realization, and the 2023 data shown below in Table 1 demonstrate that Peru can do a lot more to harness renewable energy sources.
Table 1 shows that, in first place with respect to the potential use of renewable energy is the electrical energy generated by biomass, which is equivalent to 14.67% of its potential, then in second place, the hydroelectric source in Peru is the largest and has used 7.23% of its potential, followed by the on-shore wind source with 3.26%, then the solar source with 1.59% of its potential, and the geothermal, off-shore wind, waves, and tidal sources use none of their potential.
The SEIN of Peru has an efficient generation offer of 819 MW until 2025, related to investment projects with high implementation certainty. However, from 2026 it is expected that there will be a deficiency in efficient electricity production in the SEIN due to future high consumption, which would be an additional 1600 MW by 2030 [4]. This means that if the required efficient generation is not met by 2026, thermal power plants run by diesel will come into operation, increasing the electricity costs and GHG emissions of the system.
To address the surge in energy demand, Peru must promptly meet its electricity generation needs. International pressures urging an energy transition focused on a sustainable model direct us to leverage Peru’s abundant renewable energy potential as a promising avenue to enhance energy supply through the utilization of non-conventional renewable resources like solar, wind, biomass, and geothermal energy. In this context, solar energy is playing a significant role in the energy landscape of the country, being one of the most attractive clean-energy options for energy companies. Figure 1 shows the potential for wind, hydroelectric, and solar energy in the northern, central, and southern territories of Peru.
Figure 1 indicates that the northern zone of Peru has a high wind potential that has not yet been used. In addition, in the central zone of Peru in the Andes sector there is a high hydroelectric potential and, finally, in the southern zone of Peru, there is an extraordinary solar potential that has not yet been fully exploited.
Considering the use of more clean energy presents several key issues. First, it needs to be produced. This will mean increasing our availability to generate electricity from renewable resources with the least impact on ecosystems, particularly through solar, geothermal, and wind energy technologies. More renewable energy plants will be needed, and more electricity will also be generated locally, using, for example, photovoltaic rooftops, micro-hydroelectric plants, and micro wind turbines [10].
In this sense, massive investments will be needed to expand and modernize Peruvian electrical networks to account for the increase in loads and different energy sources. Electricity will need to be transmitted from solar photovoltaic facilities, concentrated solar facilities, offshore wind turbines, or remote geothermal plants to towns and cities while minimizing the impact of new transmission lines or underground cables [11].
Regarding technical aspects, two relevant issues will allow humanity to meet its energy demands using clean sources: (i) it is necessary to decrease electricity needs by improving energy efficiency and decreasing energy waste; and (ii) because electricity and heat are the mechanisms of energy most easily generated from renewable energy, the use of electricity and direct heat will have to be optimized, supported by improvements to electrical networks [12].

1.2. A Promising Future of Sustainability with the Use of Solar Renewable Energy

Solar energy utilization has benefits not only for the environment, such as the reduction of the carbon footprint, as it is a clean technology, and it is possible to generate electricity using solar facilities in strategic places of the Peruvian territory. The solar energy industry is following the advances of the wind energy industry in Peru, where all stakeholders (communities, authorities, investors, and NGOs, among others) of the territory are accepting this clean energy as a road to reach sustainable development [8]. Thus, we can see that the main benefits of using solar technology for energy generation are as follows:
Firstly, the reduction of GHG emissions. Relevant information indicates that 97% of the electrical energy that was consumed during the first mandatory social isolation against COVID-19 was generated from renewable sources such as solar, avoiding the emission of more than 0.4 Mtons of carbon dioxide equivalent (CO2eq), from other energy sources [13,14].
Secondly, the use of energy sources from the sun avoids the use of highly polluting fossil fuels (e.g., oil, coal, pet coke, and natural gas, among others) [15]. According to the Intergovernmental Panel on Climate Change, including the whole life cycle of the different technologies, utility-scale solar energy plants emit 48 gCO2eq/kWh on average, with much lower emissions than coal power plants, which emit 820 gCO2eq/kWh, or combined-cycle natural gas power plants, which emit 490 gCO2eq/kWh [16].
Thirdly, the use of energy sources such as solar panels or solar facilities creates employment opportunities and increases the value of the properties surrounding the built infrastructure [6].
Fourthly, the generation of solar energy contributes to the supply of energy to communities that are far away, contributing to their development and visibility. Solar energy generation projects allow the facilities to be located where energy from other sources does not reach, such as energy plants that must be close to fossil fuel extraction points [17].
In Peru, over the years, solar energy generation projects and their importance, as indicated by international treaties and conferences, and of course the promulgation of general regulations for their development, have been mainly promoted by the MINEM. Thus, the start of new electrical generation using clean-energy resources such as solar has even been announced as a national priority and subject of public interest [18].
Without prejudice to the above and the effort imposed by the MINEM, with the support of environmental organizations such as the Ministry of the Environment (MINAM) and various NGOs, the measures implemented by the Peruvian government still do not cover the minimum electricity production through solar energy. Accordingly, a large percentage of electrical energy still comes from the burning of fossil fuels and hydroelectric plants [19].
Solar energy, along with wind energy, is the main target of the current energy transition. Although not often taken into account until a few decades ago, it is now experiencing rapid growth: global solar PV capacity increased from 40 GW in 2010 to 580 GW in 2019 [20]. The credit goes to technological innovation, mainly in the materials science sector, which made solar PV facilities competitive, even from an economic point of view compared with fossil sources. Considering the information published by IRENA, the costs of photovoltaic energy production have dropped by 82% in the last decade. The prospects are even more encouraging: with new generation technologies, it will be feasible to increase the efficiency of PV panels by 30% compared with nowadays, and energy generation by more than 20% [20].
Solar energy using photovoltaic cells, which transform sunlight directly into electricity, can be incorporated into industries, houses, or city infrastructures [21]. A photovoltaic solar system transforms the radiant energy emitted by the sun into electrical energy using photovoltaic panels. These cells are made of silicon, a semiconductor element that generates small amounts of electrical energy when it receives a significant amount of radiation. Photovoltaic cells are the basic units and elements that form so-called photovoltaic modules or panels and photovoltaic fields [22]. A photovoltaic module or panel is made up of the union and interconnection of a defined number of cells, whose electrical arrangement in series or parallel will lead to the generation of a certain voltage measured in volts and a current intensity measured in amperes. In general, a photovoltaic cell generates a voltage of approximately 0.5 volts; therefore, the interconnection of 36 cells in series will generate about 18 volts (12 working volts) [23]. Today, at a commercial level, there are modules with 36, 60, and 72 cells whose interconnection will determine the working voltage of the module. Figure 2 shows a typical schematical view of a functioning solar photovoltaic facility.
According to Figure 2, the sun emits solar radiation, which is captured by the photovoltaic panels where said solar radiation is transformed into electrical energy through the flow of electrons generated in the photovoltaic cells. Then, the flow of electrons from the photovoltaic cells is conducted by cables as a direct current to a system called an inverter or converter. In this system, the direct electrical current is transformed into an alternating electrical current [25]. Finally, the alternating electrical current is conducted to urban, industrial, or commercial areas through high-, medium-, and low-voltage electrical transmission networks.
Now, it is important to keep in mind that international organizations promote the use of clean technologies for energy generation such as solar facilities, and they invite countries to replace fossil energy sources or the generation of energy based on the burning of polluting elements [26].

1.3. Aim of the Article

Solar energy stands as an attractive alternative to cope with the effects of climate change in Peru, aligning with the United Nations Sustainable Development Goals (SDGs) outlined in the 2030 Agenda. This review studies the solar PV energy generation potential in the country. Additionally, the production of electricity from solar energy in the future is presented by studying a relevant portfolio of solar PV facilities, where an equivalent installed capacity of 7218 MW is projected to be carried out in 2028 (Figure 3).
Furthermore, this article outlines the key advantages, benefits, and limitations associated with introducing solar energy facilities in Peru, focusing on (i) assessing the potential of the solar resource at hand, (ii) describing the current solar photovoltaic facilities, (iii) describing the portfolio of solar photovoltaic (PV) projects up to 2028, and (iv) analyzing the hybridization with other solar energy technologies. Additionally, recent advances, challenges, and prospects in the implementation of the clean-energy industry from solar sources are discussed.
This review contribution highlights the application of solar energy technologies in Peru to improve human livelihood and well-being, considering the negative impacts of the climate change crisis faced by society. In this sense, this review is relevant for scientists, economists, politicians, professionals, and communities, among others, being a database for future research and an example of applying actions for the mitigation of climate change by (i) publishing data on solar resource potential and the use of solar energy in Peru, (ii) describing actions carried out by Peru to promote the implementation of renewable solar energy, (iii) showing the compromise and efforts of Peru to cope with the climate change crisis, and (iv) sharing practical experience in technical, social and environmental issues regarding the implementation of solar energy technologies to make a sustainable society, among others.

2. Potential of Solar Energy Resources in Peru

In Peru, the orographic, climatic, and oceanographic conditions, among other factors, determine the existence of three large natural regions: the coast, the Andes Mountains, and the jungle. The coast is the region limited by the Pacific Ocean and the Andean slopes below 2000 masl. The Andes Mountains are characterized by the presence of peaks and mountains with heights of 6768 masl. The jungle is a region formed by two zones, the Amazonian tropical forest or low jungle and the slopes and valleys to the east of the Andes below 2000 masl known as the high jungle [1].
The distribution of the solar resource primarily drives the geographical variability of the solar energy yield. The key characteristics of the solar resource are defined mainly by latitude, the presence of clouds, topography, shade, atmospheric aerosol concentration, and air moisture content [27].
Considering annual variations, the area with the greatest solar energy potential in the Peruvian territory is mainly located on the southern coast (16° to 18° S), where global horizontal irradiation (GHI) of 6.0 to 6.5 kWh/m2/day is available. Other areas in which high availability of daily solar energy is recorded, with global horizontal irradiation (GHI) of 5.5 to 6.0 kWh/m2/day, are the northern coast (3° to 8° S) and a large part of the mountains above 2500 masl. In order of importance in terms of their surface area, these include the southern mountain range, the central mountain range, and the northern mountain range. The area with low solar energy values in the territory is the jungle, where values of global horizontal irradiation (GHI) of 4.5 to 5.0 kWh/m2/day are recorded, with an area of minimum values in the extreme north near the equator (0° to 2° S) [28].
When explaining the distribution of solar energy in the Peruvian territory, we must take into account various factors that control the climate, such as the Andes mountain range, which shapes the orography of the Peruvian territory; the South Pacific Anticyclone, which produces great atmospheric stability owing to the presence of downward vertical movements in the middle troposphere; the South Atlantic Anticyclone, which provides humidity and feeds the south-east trade winds; the Peruvian cold current in the Pacific Ocean, which reinforces stability in the atmosphere; the Equatorial warm current (El Niño Southern Oscillation—ENSO), which destabilizes the atmosphere on the northern coast in the summer months; the Intertropical Convergence Zone, which generates very active cloud systems; and the Alta of Bolivia, which is associated with convective systems that tend to mainly affect the northern and central mountains and jungle of Peru [28].
In general terms, in the central and southern coast regions, high values of solar energy occur during the austral summer; however, it is necessary to detail some exceptions. In the coastal strip close to the coast, located below 600 masl, the behavior described above changes during late autumn, winter, and early spring, when this region shows markedly low levels of solar energy and constitutes an area of minima in the territory. At the end of spring, on the desert terraces of Arequipa, Moquegua, and Tacna (13.5° to 18° S and 70° to 76° W) above 1000 masl, the highest annual values of solar energy of the Peruvian territory are reached. This is because they are located above the thermal inversion layer and have clear skies throughout the year. The northern coast, between 3° and 6° S and 80° to 81° W (the regions of Tumbes, Piura, and northern Lambayeque) also presents high values of solar energy during the austral summer; however, the maximum values of solar energy in October and November (spring) are also high in annual terms [28].
According to the map of solar energy presented in the Global Photovoltaic Power Potential by Country report generated by ESMAP [29], Peru has considerable and underutilized solar potential. These conditions are mainly concentrated in the southern and northern parts of the country. Figure 4 shows the global horizontal irradiation (GHI) map of Peru. The irradiance level is the most crucial parameter for calculating energy yield and evaluating the performance of flat-plate photovoltaic modules. It is also the most widely adopted technology in the field.
Currently, the country has nine solar photovoltaic facilities in operation (information correct as of March 2024). All these solar PV facilities are integrated into the SEIN. Eight are found in the southern regions of (i) Arequipa (Majes and Repartición), (ii) Moquegua (Moquegua FV, Intipampa, Rubi, Panamericana Solar, and Clemesi), and (iii) Tacna (Tacna Solar) [6] (Figure 5), and one is located close to the capital city of Peru, specifically in the Lima region (Yarucaya).
These geographical areas of Peru are characterized by an average daily solar irradiation of over 6.0 kWh/m2/day, as well as capacity factors between 22% and 35% [6]. This situation facilitates efficient energy transformation, which is particularly intensified during peak hours, thereby improving SEIN’s economic commercial conditions.
The production of solar PV energy is conditioned to irradiation characteristics, which can fluctuate by season or be affected by the presence of clouds. However, solar PV facilities present a very similar hourly behavior, so the electricity generation increases accordingly [31]. Figure 6 and Figure 7 show the average hourly solar PV energy generation pattern in Peru according to the annual seasonal period and some solar PV facilities under operation in the southern region of the country in 2019.
Figure 6 corresponding to the summer season shows the time of the day when the greatest amount of electrical energy is generated in solar photovoltaic facilities in Peru (between 5:30 a.m. and 6:30 p.m.). Also, Figure 7 corresponding to the winter season shows the hours of the day when the greatest amount of electrical energy is generated in solar photovoltaic facilities (between 6:30 a.m. and 5:30 p.m.).
This behavior is a result of the reduced climatic instability in the southern region, which is attributed to the presence of aerosols and water vapor that create a dry climate with low cloud cover. Consequently, solar radiation remains stable for at least seven hours per day (in winter), facilitating consistent energy production between 8:30 a.m. and 01:30 p.m. Although electricity generation commences between 6:00 a.m. and 6:30 a.m., production continues until 06:00 p.m.
Moreover, seasonal variations can be observed based on the time of year. The winter season typically yields the lowest energy output, whereas the summer season has the highest energy generation. Specifically, the reduction in solar energy generation during the winter season can range from 30% to 50% compared with the summer months (See Figure 8).
All the solar PV facilities currently functioning are in the desert territory of Peru. In these locations, relevant amounts of solar irradiation are generated during much of the day (Figure 9). Overall, Peru’s solar resources have been estimated at a useful potential of 25 GW, and only 2% of the potential has been used as of 2024.
The usable potential study considers the technical energy capacity and production of a specific technology given resource potential, device performance, terrain restrictions, ecosystem attributes, and land-use limitations. The information to be considered in the usable potential estimation includes [32]:
  • Minimum resource constraints (4–5 kWh/m2/day),
  • Maximum allowable terrain slope (3–5%),
  • Power density for a given technology (25–30 MW/km2),
  • Maximum distance to transmission lines (5 Km),
  • Maximum distance to roads (5 Km), and
  • Land exclusion types (agricultural, forest, urban, water bodies, wetlands, and environmentally protected areas).
The non-available land area in the southern region of Peru is likely restricted by steep topography and the distance to transmission lines and roads, while the land area in the Amazon region is likely restricted by land type (forest) and insolation values [33]. The useful solar energy technical potential for Peru is equivalent to 25,000 MW. Table 2 shows details of the geographical areas of the country with the greatest average solar energy, where values between 4.00 and 7.00 kWh/m2/day are recorded.
Table 2 shows that the geographical areas of the country with the greatest solar energy potential are Arequipa, Moquegua, Tacna, Tumbes, Piura, and Ica. They highlight the relevant potential of Arequipa, Moquegua, and Tacna, with an average solar radiation of 250 W/m2. These regions are part of the Coast Desert of Peru, in which nine photovoltaic solar energy plants are in operation in 2024. Also noteworthy are the northern regions of the country (i.e., Tumbes and Piura and part of the Sechura desert), which, despite their attractive solar resources, have not been used to date. The Ica region also stands out for its attributes of renewable wind and solar resources, with wind farms already in operation but no photovoltaic solar energy plants to date. Finally, the Lima region has one solar photovoltaic facility operating called Yarucaya, and it is expected that more solar energy projects will be constructed in this region.

3. Practical Experiences of Solar Photovoltaic Facilities Registered in Peru

Below, key data and practices of the development of solar photovoltaic facilities in Peru are presented in detail, including (i) facilities in the operational stage, (ii) facilities under construction, and (iii) projected solar PV facilities (under engineering phases and/or EIA studies).

3.1. Solar PV Facilities in Operation

The following paragraphs present the solar PV facilities currently functioning in the country.

3.1.1. Repartición Solar Photovoltaic Facility—Arequipa Region

The Repartición solar facility is a facility located in the district of La Joya in the province of Caylloma, Department of Arequipa, 555 km from the city of Lima at an elevation of 1187 masl. This solar complex began its construction phase in 2011 and came into operation in July 2012. The land area occupied by the solar facility is equivalent to 102 Ha. Figure 10 shows panoramic images of the solar facility, and Table 3 provides specifications of the infrastructure.
Figure 10 shows that the Repartición solar facility is in an area close to the coastal zone in a desert landscape where no contiguous communities are located.
As shown in Table 3, this solar facility has a total of 58,000 photovoltaic modules of polycrystalline silicon. Furthermore, the power of the photovoltaic modules is 350 W, which, considering all the photovoltaic modules, means that the solar facility has an installed capacity equivalent to 20 MW, considering a tracking angle for the photovoltaic panels equivalent to 45° with an estimated capacity factor of 0.25.

3.1.2. Majes Solar Photovoltaic Facility—Arequipa Region

This solar facility is in the department of Arequipa, province of Caylloma, in the district of Majes, 550 km from the city of Lima at 1680 masl. Construction began on this solar facility in 2011 and it came into operation in July 2012. The land area occupied by the solar facility is equivalent to 102 Ha. Figure 11 shows panoramic images of the solar facility, and Table 4 provides specifications of the infrastructure.
Figure 11 shows that the Majes solar facility is in a desert area where there are no adjacent communities.
As shown in Table 4, this solar facility has a total of 58,000 photovoltaic modules of polycrystalline silicon. Furthermore, the power of the photovoltaic modules is 350 W, which, considering all the photovoltaic modules, means that the solar facility has an installed capacity equivalent to 20 MW, considering a tracking angle for the photovoltaic panels equivalent to 45° with an estimated capacity factor of 0.26.

3.1.3. Tacna Solar Photovoltaic Facility—Tacna Region

This solar facility is in the district of Tacna, province of Tacna, in the department of Tacna at 560 masl. Construction began on this solar facility in 2011 and it came into operation in October 2012. The land area occupied by the solar facility is equivalent to 102 Ha. Figure 12 shows panoramic images of the solar facility, and Table 5 provides specifications of the infrastructure.
Figure 12 shows that the Tacna Solar facility is in a desert area without adjacent communities.
As shown in Table 5, this solar facility has a total of 58,000 photovoltaic modules of polycrystalline silicon. Furthermore, the power of the photovoltaic modules is 350 W, which, considering all the photovoltaic modules, means that the solar facility has an installed capacity equivalent to 20 MW, considering a tracking angle for the photovoltaic panels equivalent to 50° with an estimated capacity factor of 0.30.

3.1.4. Panamericana Solar Photovoltaic Facility—Moquegua Region

This solar facility is in the district of Moquegua, province of Mariscal Nieto, department of Moquegua at 1410 masl. The construction phase began in 2011 and the facility came into operation in December 2012. The land area occupied by the solar facility is equivalent to 123 Ha. Figure 13 shows panoramic images of the solar facility, and Table 6 provides specifications of the infrastructure.
Figure 13 shows that Panamericana solar facility is located in a desert area where there are no adjacent communities.
As shown in Table 6, this solar facility has a total of 58,000 photovoltaic modules of polycrystalline silicon. Furthermore, the power of the photovoltaic modules is 350 W, which, considering all the photovoltaic modules, means that the solar facility has an installed capacity equivalent to 20 MW, considering a tracking angle for the photovoltaic panels equivalent to 55° with an estimated capacity factor of 0.33.

3.1.5. Moquegua FV Solar Photovoltaic Facility—Moquegua Region

The Moquegua FV solar facility is in the district of Moquegua, province of Mariscal Nieto, department of Moquegua. Construction began on this solar facility in 2013 and it came into operation in December 2014. The land area occupied by the solar facility is equivalent to 134 Ha. Figure 14 shows panoramic images of the solar facility, and Table 7 provides specifications of the infrastructure.
Figure 14 shows that the Moquegua FV solar photovoltaic facility is in a desert area with no communities around it.
As shown in Table 7, this solar facility has a total of 58,000 photovoltaic modules of polycrystalline silicon. Furthermore, the power of the photovoltaic modules is 280 W, which, considering all the photovoltaic modules, means that the solar facility has an installed capacity equivalent to 16 MW, considering a tracking angle for the photovoltaic panels equivalent to 55° with an estimated capacity factor of 0.34.

3.1.6. Intipampa Solar Photovoltaic Facility—Moquegua Region

The Intipampa solar facility is in the district of Moquegua, province of Mariscal Nieto, department of Moquegua, approximately 700 km from the city of Lima near the Panamericana Sur highway at 1410 masl.
The Intipampa solar facility came into operation in March 2018, and Engie Energía Perú S.A. began construction in January 2017. The land area occupied by the solar facility is equivalent to 322 Ha. Figure 15 shows panoramic images of the solar photovoltaic facility, and Table 8 provides specifications of the infrastructure.
Figure 15 shows that the Intipampa solar photovoltaic facility is in a desert area where there are no adjacent communities.
As shown in Table 8, this solar facility has a total of 125,000 photovoltaic modules of polycrystalline silicon. Furthermore, the power of the photovoltaic modules is 325 W, which, considering all the photovoltaic modules, means that the solar facility has an installed capacity equivalent to 40 MW, considering a tracking angle for the photovoltaic panels equivalent to 55° with an estimated capacity factor of 0.27.

3.1.7. Rubi Solar Photovoltaic Facility—Moquegua Region

The Rubi solar photovoltaic facility is in the district of Moquegua, province of Mariscal Nieto, department of Moquegua, at 1410 masl. Construction began on this solar facility in 2017 and it came into operation in 2018. The land area occupied by the solar facility is equivalent to 400 Ha. Figure 16 shows panoramic images of the solar facility, and Table 9 provides specifications of the infrastructure.
Figure 16 shows that the Rubi solar photovoltaic facility is in a desert area where there are no contiguous communities.
As shown in Table 9, this solar facility has a total of 450,000 photovoltaic modules of polycrystalline silicon. Furthermore, the power of the photovoltaic modules is 320 W, which, considering all the photovoltaic modules, means that the solar facility has an installed capacity equivalent to 144 MW, considering a tracking angle for the photovoltaic panels equivalent to 45° with an estimated capacity factor of 0.35.

3.1.8. Clemesi Solar Photovoltaic Facility—Moquegua Region

The Clemesi solar photovoltaic facility is in the district of Moquegua, province of Mariscal Nieto, department of Moquegua, at 1503 masl. Construction began on this solar facility in 2021 and it came into operation in 2023. The land area occupied by the solar facility is equivalent to 300 Ha. Figure 17 shows panoramic images of the solar facility, and Table 10 provides specifications of the infrastructure.
Figure 17 shows that the Rubi solar photovoltaic facility is in a desert area where there are no contiguous communities.
As shown in Table 10, this solar facility has a total of 221,000 photovoltaic modules of polycrystalline silicon. Furthermore, the power of the photovoltaic modules is 525 W, which, considering all the photovoltaic modules, means that the solar facility has an installed capacity equivalent to 116.45 MW, considering a tracking angle for the photovoltaic panels equivalent to 50° with an estimated capacity factor of 0.35.

3.1.9. Yarucaya Solar Photovoltaic Facility—Lima Region

The Yarucaya solar photovoltaic facility is in the district of Sayan, province of Huaura, department of Lima, at 1031 masl. Construction began on this solar facility in 2020 and it came into operation in 2021. The land area occupied by the solar facility is equivalent to 3.3 Ha. Figure 18 shows panoramic images of the solar facility, and Table 11 provides specifications of the infrastructure.
Figure 18 shows that the Yarucaya solar photovoltaic facility is in a valley area where there are some communities.
As shown in Table 11, this solar facility has a total of 3070 photovoltaic modules of polycrystalline silicon. Furthermore, the power of the photovoltaic modules is 350 W, which, considering all the photovoltaic modules, means that the solar facility has an installed capacity equivalent to 1.62 MW, considering a tracking angle for the photovoltaic panels equivalent to 45° with an estimated capacity factor of 0.22.

3.1.10. Summary of the Total Installed Capacity of Solar Photovoltaic Energy in 2024

Table 12 shows the key specifications of the solar PV facilities functioning in Peru, showing the capacity of the solar PV energy infrastructure, and Figure 19 shows the percentage of electrical energy generated by solar PV facilities in Peru.
Table 12 shows that, as of March 2024, there is a total of nine solar photovoltaic facilities in operation in Peru. In addition, it is possible to see that five solar photovoltaic facilities are in the southern part of Peru in the Moquegua region, while another two solar photovoltaic facilities are located in the Arequipa region, one solar photovoltaic facility is in the Tacna region, and one solar photovoltaic facility is in Lima region. It is observed that the solar photovoltaic facility with the lowest energy-generation capacity is Central Solar Yarucaya with 1.62 MW, while the Central Solar Rubi is the facility with the highest energy-generation capacity at 144 MW. Figure 19 shows the percentage of electrical energy generated by solar photovoltaic facility sources in Peru, with 46% of the total installed capacity corresponding to Central Solar Rubi. Finally, for the nine solar photovoltaic facilities in operation, the total installed capacity is 398.07 MW. The installed capacity as of 2024 is equivalent to 2% of the useful solar potential of 25 GW.
Figure 20 summarizes the quantity of annual energy produced in GWh and the capacity factor of each solar PV facility that is functioning in the country.
Figure 20 shows that the solar photovoltaic facility that produces the greatest amount of annual energy is Central Solar Rubi with approximately 441.5 GWh, while the Central Solar Yarucaya produces the least annual energy with 3.1 GWh. This is due to the power installed in each solar facility. Additionally, the capacity factors fluctuate in a range between 0.22 for Central Solar Yarucaya and 0.35 for Central Solar Clemesi and Central Solar Rubi.
Finally, Figure 21 shows the development over time of the installed capacity in MW of solar PV energy in Peru.
Figure 21 shows that the first stage of solar PV energy in the country began in 2012, with strong growth from 2012 to 2023.

3.2. Solar PV Facilities Approved and under Construction in 2024

The following paragraphs provide details on solar photovoltaic facilities with an approved EIA study that are under construction in 2024.

3.2.1. San Martin Solar Photovoltaic Facility—Arequipa Region

The new San Martin solar photovoltaic facility is in the district of La Joya, province of Arequipa, department of Arequipa, at 1350 masl. Construction began on this solar facility in 2023 and it will come into operation in 2025. The land area occupied by the solar facility will be equivalent to 550 Ha. Figure 22 shows a typical image of the solar facility, and Table 13 provides specifications of this renewable energy facility.
Table 13 shows that this solar facility will have a total of 1,000,000 photovoltaic modules of polycrystalline silicon. Furthermore, the power of the photovoltaic modules will be 300 W, which, taking into account all the photovoltaic modules, means that the solar facility will have an installed capacity equivalent to 300 MW, considering a tracking angle for the photovoltaic panels equivalent to 50° with an estimated capacity factor of 0.40. This solar energy facility will generate 1000 GWh of electricity annually for the SEIN.

3.2.2. Lupi Solar Photovoltaic Facility—Moquegua Region

The new Lupi solar photovoltaic facility will be in the district of Carumas, province of Mariscal Nieto, department of Moquegua, at 4500 masl. This will be one of the highest-altitude photovoltaic solar energy projects in the world. Construction on this solar facility will begin in 2024 and it will come into operation in 2025. The land area occupied by the solar facility will be equivalent to 275 Ha. Figure 23 shows a typical image of the solar facility, and Table 14 provides specifications of the infrastructure.
Table 14 shows that this solar facility will have a total of 470,000 photovoltaic modules of crystalline silicon. Furthermore, the power of the photovoltaic modules will be 320 W, which, considering all the photovoltaic modules, means that the solar facility will have an installed capacity equivalent to 150 MW, considering a tracking angle for the photovoltaic panels equivalent to 45° with an estimated capacity factor of 0.32. This solar energy facility is expected to generate 420 GWh of electricity annually for the SEIN.

3.2.3. Matarani Solar Photovoltaic Facility—Arequipa Region

The new Matarani solar photovoltaic facility will be in the district of Mollendo, province of Islay, department of Arequipa, at 500 masl. Construction began on this solar facility in 2023 and it will come into operation in 2024. The land area occupied by the solar facility will be equivalent to 130 Ha. Figure 24 shows a typical image of the solar facility, and Table 15 provides specifications of the infrastructure.
Table 15 shows that this solar facility will have a total of 123,500 photovoltaic modules of polycrystalline silicon. Furthermore, the power of the photovoltaic modules will be 650 W, which, considering all the photovoltaic modules, means that the solar facility will have an installed capacity equivalent to 80 MW, considering a tracking angle for the photovoltaic panels equivalent to 40° with an estimated capacity factor of 0.35. This solar energy facility will generate 245 GWh of electricity annually for the SEIN.

3.2.4. Summary of the Total Installed Capacity of Solar Photovoltaic Energy under Construction in 2024

Table 16 shows the key specifications of the solar PV facilities under construction in the country in 2024, indicating the installed capacity of each solar facility and the total installed capacity of solar PV energy.
Table 16 shows that by the end of 2024, there will be three solar photovoltaic facilities under construction in Peru. Furthermore, all facilities will be in the regions of Moquegua and Arequipa. It is observed that one of the new solar photovoltaic facilities is large, considering the existing facilities currently in operation, with an installed capacity of over 300 MW. Finally, considering the three new solar photovoltaic facilities in construction as of March 2024, the total projected installed capacity is equivalent to 530 MW.

3.3. Solar PV Facilities for the Future—Under Engineering Phase and EIA Study Processing

The COES has projected an income of 7218 MW from solar photovoltaic facilities by the year 2028 [4]. Table 17 shows the specifications of the solar PV facilities projected in Peru for the period 2024–2028 that are currently under engineering studies and processing of EIA studies.
Table 17 shows that there is a total of 33 solar photovoltaic facility projects planned to be executed in Peru between 2024 and 2028 Furthermore, it is possible to see that the projects are in the northern zone (Piura) and southern zone (Ica, Tacna, Moquegua, Puno and Arequipa) of Peru. It is observed that the solar photovoltaic facility project with the lowest expected energy-generation capacity is the Central Solar Windica at 25 MW, while the Central Solar Sol de Verano III project is the solar photovoltaic facility with the highest expected energy-generation capacity at 600 MW. Finally, considering the 33 solar energy projects, the total projected installed capacity is equivalent to 7218 MW.

4. Discussion

4.1. Registered Progress

4.1.1. Potentialities and Limitations of Solar Photovoltaic (PV) Energy in Peru

Solar PV energy advances on a large scale have already been carried out in Peru, as they are environmentally friendly and an attractive option to apply in different geographical locations with solar resource potentialities. In terms of the knowledge acquired about solar energy projects in Peru since 2012, the key potentialities and limitations are shown in Table 18.
The key potentialities shown in Table 18 indicate that the ecosystem damage to land from this clean-energy source is limited. It is also shown that its functioning is not complex to implement, and it also produces a large number of jobs, mainly during the construction process. Some limitations are observed, considering that it is a fluctuating energy technology, restricted to hours of daylight, and it is cannot be applied in lands of heritage, protected environmental zones, and/or archaeological areas.
Table 18 above shows the main benefits offered by solar energy. However, its implementation also imposes challenges that must be faced. The main challenges are unavailability (or intermittency), its large-scale integration, and the impact it can have on the rates paid by users.
An obvious disadvantage of solar energy is that its supply is intermittent. Photovoltaic cells do not work during the night, although most electricity is demanded in daylight hours when sunlight is intense, and they are less effective when clouds are present.
Intermittency is defined as the unplanned unavailability or interruption of electricity generation from some renewable energy sources such as wind and solar, which, by definition, fluctuate. Solar energy’s intermittency depends on the radiation level in a certain geographical area. It generally has a diurnal and seasonal pattern, that is, it reaches greater intensity during the day and in summer. Furthermore, seasonal intermittency is greater the further away you are from the equator. Diurnal and seasonal patterns provide some predictability in solar generation; however, radiation can be affected by other weather conditions that are difficult to predict, such as cloud cover and the composition of the atmosphere. Thus, a thick cloud layer can absorb available solar radiation, thereby decreasing energy production [35].
The operation of the current nine solar PV facilities conforms to the support of future solar energy investments to be implemented in Peru. The knowledge acquired to date has allowed construction companies to work in an environmentally friendly way during the implementation of solar energy projects. Experience has also been acquired in environmental impact assessment (EIA) studies and acquiring socio-environmental licenses for operation.
The advances in solar energy in Peru are helping the clean transformation of the energy matrix; however, its application is still in the early stages despite the enormous potential available [36].

4.1.2. New Technologies Applied to Solar Photovoltaic (PV) Energy Projects in Peru

Solar facilities are optimizing their photovoltaic panel inspection processes with the help of drones, especially those located in places where high solar radiation makes manual field surveys even more difficult for personnel. The integration of drones allows solar energy facility operators to decrease surveys by 70% compared with conventional human techniques. Traditional surveys of photovoltaic solar facilities entail the review of panels one by one with the human use of a laser temperature device. After identifying faults in solar panel arrays, field workers register the positions of the panels for repair or replacement. Considering the large scale of these solar photovoltaic facilities, these conventional techniques are inefficient for operation and maintenance field operators.
The use of technological advances in the Industry 4.0 paradigm, such as the integration of drones, also known as unmanned aerial vehicles (UAVs), increases the efficiency and precision of inspections of photovoltaic panels in solar plants [37]. Drones equipped with thermal cameras can carry out surveys of vast zones of photovoltaic solar facilities, collecting high-resolution RGB and thermal map data. Thermal imaging facilitates fault detection based on abnormal temperature patterns between cells or panels (Figure 25). Using a combination of visual RGB information and thermal maps, it is possible to estimate whether these abnormal temperature patterns are the result of physical conditions such as delamination, cracking, or particulate matter, or if they are due to connectivity issues such as inverter failures or wiring faults [37].
Photogrammetry software reconstructs RBG orthomosaic and thermal maps and adjusts the location using ground control points. After location and rebuilding adjustments, maps are created and then linked to a GIS, where solar energy facility field operators can rapidly identify anomalies and detect solar panel failures [38].
Figure 25. Example of high-resolution RGB and thermal images obtained by drone flight for conducting a PV panel inspection in a solar energy plant (layout view). Adapted from [39].
Figure 25. Example of high-resolution RGB and thermal images obtained by drone flight for conducting a PV panel inspection in a solar energy plant (layout view). Adapted from [39].
Sustainability 16 04388 g025
It is expected that in the coming years, the evolution of artificial intelligence (AI) and machine learning (ML) technologies as part of the Industry 4.0 paradigm will contribute to the solar energy industry, for example, in global solar irradiation modeling/prediction and solar power production estimates, among other areas [40,41].
Finally, we can mention one of the most important technological advances applied in photovoltaic solar energy plants in Peru, the use of photovoltaic panels called bifacial solar panels. Bifacial solar panels can capture energy on both sides of the photovoltaic solar panel, whereas monofacial modules only receive energy on their front side [42]. Bifacial modules expose both the front and back of solar cells (See Figure 26).
When bifacial modules are installed on a highly reflective surface, up to a 25% increase in power output can be obtained just from the additional power harvested from their rear [42]. Bifacial modules have different configurations, such as (i) framed or (ii) frameless. Other key characteristics of bifacial modules are with respect to their materials, such as: (i) some have double glass, or (ii) some use transparent back sheets. The vast majority use monocrystalline cells, but polycrystalline arrays also exist.
Bifacial technology is expected to strongly enter the market and account for one-third of global solar module production by 2025. Bifacial and half-cell solar panel technologies have gained momentum owing to their improvements in solar energy harvesting.
The intermittent nature of solar photovoltaic (PV) generation, which depends on the weather and amount of daylight, presents a particular issue. In this sense, accurate solar energy forecasting has emerged as a critical issue in maximizing energy production and seamlessly integrating solar power into the grid to overcome this obstacle. Some key aspects of carrying out a forecast model for further economic growth in the use of solar energy sources are (i) resource planning and investment decisions, (ii) optimizing energy production, (iii) grid stability and reliability, and (iv) economic efficiency.
In this context, the Energy and Mines Ministry of Peru considers conventional weather-based solar energy forecasting models and in recent years has incorporated the following cutting-edge technologies to improve solar irradiation prediction precision: (i) satellite data, (ii) artificial intelligence (AI), and (iii) machine learning (ML).
For decades in Peru, forecasts of solar energy have been based on conventional weather-based models. These models are based on historical meteorological information, which includes parameters such as solar irradiance, temperature, cloud cover, and humidity, among others. These models frequently have trouble when there is cloud cover or other unfavorable weather conditions rather than clear skies.
Satellites with cutting-edge remote sensors offer a variety of useful information for solar forecasting by incorporating satellite data into conventional solar forecasting models. They can take high-resolution pictures of the Earth’s surface and atmosphere, which enables tracking of significant meteorological variables like cloud cover and water vapor concentration in real time.
Solar energy forecasting carried out by the Energy and Mines Ministry of Peru uses artificial intelligence (AI) and machine learning (ML) algorithms to process massive volumes of weather data. Prediction accuracy is greatly increased by using historical information on solar energy output, weather patterns, satellite photography, and artificial intelligence (AI)/machine learning (ML) algorithms. Some examples of the tools used are (i) convolutional neural networks (CNNs) and (ii) recurrent neural networks (RNNs), which have demonstrated promise in the analysis of satellite pictures and the identification of cloud-cover patterns that impact solar irradiance. These models have been trained to recognize various cloud forms and calculate how they will affect solar energy output.

4.2. Policy Gaps

Even though Peru has legislation related to the promotion of investment for the generation of electricity with the use of renewable energy in Legislative Decree N° 1002 and its regulations approved by Supreme Decree N° 050-2008-EM and modified by Supreme Decree N° 012-2011-EM, renewable energy projects still face policy barriers for their appropriate implementation in the electricity market [6].
One of the main limitations of solar projects is that the current technical procedure for the calculation of firm power in Peru is based on the electricity system’s peak hours (between 05:00 p.m. and 11:00 p.m.) when solar radiation is not present. Therefore, solar projects cannot state any amount of firm power and receive income for it. Moreover, there are no separate markets for energy and power that allow solar projects to commercialize energy through power purchase agreements.
Complementary regulation is needed to compensate solar projects for the energy and firm power that they offer, considering that the peak hours for electricity consumption in Peru are not necessarily between 05:00 p.m. and 11:00 p.m. Also, regulations to let solar projects participate in long-term tenders that are controlled by the electricity distributors are suggested, as well as the publication of the distributed generation regulation.

4.3. Challenges and Opportunities Linked with Sustainability

Peru can become a development pole and place of technological innovation in the production of electricity using solar energy. For example, one of the technologies not applied in the country is a concentrated solar power (CSP) facility, where heliostats are used to locate the sun’s rays in a specific area where the heat is concentrated [44]. Unlike conventional solar PV facilities, concentrated solar power (CSP) facilities use technological advances that allow the sun’s heat to be stored to produce electricity for 24 h. Figure 27 shows an example of this technology.
Figure 27 shows that one of the key elements of this type of project is the 250-m central tower where the heat receiver is placed and to which the thousands of heliostats will point. The heliostats are mirrors with a reflective surface of 140 m2 and a weight of three tons each, and they follow the path of the sun with movement along two axes, reflecting and directing solar radiation toward the receiver. Molten salts circulate through this receiver at a temperature of 560 °C, transferring the heat to a circuit that drives a steam turbine to generate electrical energy [45].
For example, concentrating solar systems could store energy in the form of heat for up to 15 h per day. The aspect of fluctuation can also be addressed by integrating solar electricity with alternative clean-energy sources. In South America, the first project of this type was inaugurated in Chile, where the concentrated solar power (CSP) plant occupies an area of 1000 Ha and is located on Cerro Dominador, a location with one of the highest solar radiation levels on the planet, located close to the city of Calama in the Antofagasta region [46,47,48].
Solar irradiation levels are higher in the south of Peru due to the reduced presence of water vapor, which is why direct normal irradiance (DNI) levels in this area ranging from 5.2 to 8.8 kWh/m2/day can be reached [29]. For example, regarding solar irradiance, in the southern area of the Tacna region, an average of 750 W/m2 is received at noon in the coastal zone, with up to 990 W/m2 in higher-altitude areas. These values are suitable not only for solar PV technology but also for concentrated solar power (CSP) systems. These systems typically require a midday direct normal irradiance (DNI) ranging from 800 to 950 W/m2 to be technically and economically feasible. In Peru, some basic studies have been conducted to validate their feasibility, leading to favorable results. Of these, special attention is deserved by the hybridization of solar energy infrastructure with other clean-energy technologies [49]. For example, the hybridization of solar photovoltaic (PV) with concentrated solar power (CSP) facilities ensures energy delivery within a window of up to 10 to 11 h per day, with solar energy storage systems taken as a reference. This is largely controlled by the excellent conditions of the sun source. Solar thermal technologies show great promise, particularly in regions with high direct normal irradiance (DNI) levels, such as northern Chile and southern Peru. Despite Peru’s abundant solar resources that are ideal for the implementation of such technology, solar thermal technology has not yet been introduced in the country.
Considering Table 19, which shows the current technologies and technical conditions in Peru, the most viable options would likely be the utilization of parabolic trough collectors and solar power tower projects.
Table 19 shows that it is possible that these concentrated solar power (CSP) technologies would be particularly profitable if hybridized with other energy systems. In this case, the hybridization of solar photovoltaic (PV) with tower concentrated solar power (CSP) facilities would ensure energy delivery within a window of up to 10 to 15 h, with thermal storage systems taken as a reference. This is largely considering the excellent conditions of the sun source in the site-specific conditions of Peru. Also, the hybridization of solar photovoltaic (PV) energy with existing on-shore wind energy plants or future off-shore wind energy facilities appears to be promising, especially in areas where both resources converge, such as the coast of the Ica region. Similarly, hybridization with hydropower proves to be significant, with Yarucaya serving as a prime example of successful operation in regions abundant in hydro resources and suitable solar conditions. The solar photovoltaic (PV) plants collaborate with a hydroelectric facility under the ownership of the Huaura Power Group, and both belong to CFI Holding. Together, they form the initial renewable hybrid system integrated into the SEIN.
The stringent environmental assessment requirements often cause delays, and many of the prescribed procedures are better suited for the oil and gas industry rather than renewable energy projects.
While the potential for renewable energy development in the Amazon and Andes regions is substantial, these areas lack the necessary transmission infrastructure to distribute electricity nationwide. Therefore, investing in large-scale renewable energy projects may require substantial upfront investment in transmission infrastructure.

4.4. Sustainable Grid Integration

Based on the above, it is evident that the solar technologies suitable for development in Peru include photovoltaic (PV) systems and concentrated solar power (CSP) facilities using both parabolic solar collectors and central tower configurations, as well as hybrid systems combining solar photovoltaic (PV) and concentrated solar power (CSP) with or without energy storage systems. To successfully implement these technologies, certain considerations need to be considered:
  • Grid Stability: The variability of solar photovoltaic (PV) generation can impact grid stability, underscoring the need for energy storage systems to enhance grid stability. Solar thermal systems with storage offer increased reliability and resilience.
  • Regulation and Standards: As these would be new systems in Peru, having well-defined regulations and current standards is crucial for the seamless integration of solar photovoltaic (PV) systems into the National Interconnected Electrical System (SEIN). This is particularly important in the southern region, which boasts significant solar potential.
  • Transmission Capacity: The geographic location of solar photovoltaic (PV) and concentrated solar power (CSP) projects, along with their distance from grid connection points, may influence transmission capacity and necessitate upgrades to the transmission infrastructure. Strengthening transmission lines and enabling energy exchange with other countries can be beneficial.
  • Solar Irradiation Prediction Systems: Implementing predictive models for solar radiation and generation behavior is essential to anticipate voltage fluctuations caused by factors like cloud cover or unexpected solar photovoltaic (PV) system failures. This predictive capability ensures the continuity and reliability of electrical supply.
By considering these conditions and factors, Peru can effectively harness solar energy resources for sustainable and reliable electricity generation, paving the way for a cleaner and more resilient sustainable energy future.

4.5. Outlook and Future Directions

A promising large-scale advance of clean energy has been achieved in Peru through the under-functioning of solar PV facilities, but the implementation of solar energy on a smaller scale still needs to be promoted in remote communities in rural areas [21,51]. This would promote rural electrification and benefit many persons that still do not have electricity [52,53,54,55,56].
In the south of the country, the regions of Ica, Moquegua, Arequipa, and Tacna have some of the highest solar radiations in the world, with values of 6.5 kWh/m2/day equivalent to 2300 kWh/kW. This represents an opportunity for the mining sector to implement sustainability solutions and contribute to the road to carbon neutrality, as there are important mining operations in the country, such as Cerro Verde, Cuajone, Toquepala, Las Bambas, Antapaccay, San Rafael, Pucamarca, and Quellaveco, among others. Likewise the south of the country has a large portfolio of new phases of mining projects such as San Gabriel, Mina Justa, Corocohuayco, Inmaculada, Los Chancas, Corani, Pampa de Pongo, Tia María, Los Calatos, and Zafranal, among others [7]. For example, some studies have been carried out in Chile to implement solar energy technologies and hybridize with other clean-energy infrastructures in copper mining projects, providing a road to a green mining solution [57].
There are high expectations that the country’s political authorities will foster public policies that seek the implementation of solar energy facilities, which will allow the production of clean energy and foster sustainable development and human well-being.
Some countries in South America have extraordinary attributes for implementing solar photovoltaic facilities to take advantage of renewable solar energy. Western South America is one of the most significant global horizontal irradiation (GHI) hotspots on the planet. Results of studies presented in the Global Solar Atlas place Chile as the South American country with the highest practical long-term solar energy production potential, with 5.00 kWh/m2/day on average, followed by Peru and Bolivia. However, South America has been unable to take full advantage of solar energy to date and has faced difficulties such as high initial investment costs, legal and economic barriers for investors, and a lack of policies from governments that promote the mass implementation of this technology, among others [58].
It is recommended that Peru considers as a guide the successful experience of solar energy advances in neighboring South American countries, such as Chile and Brazil, where there is an important number of solar photovoltaic (PV) facilities in operation. Chile is a reference country for Peru considering its technological development and aggressive policy of implementation of renewable energies, where, for example, alliances have been created between energy-generating companies and mining companies, where copper and lithium mining projects, photovoltaic solar (PV) plants, concentration solar power (CSP) plants, and solar energy storage systems are being implemented [59,60,61,62,63].
The solar photovoltaic (PV) facilities in Peru are in sites that, until now, presented adequate solar energy potential; however, given the diverse site-specific characteristics of Peru with respect to the complex conditions of geography, terrain, and climate, high CAPEX is required to build infrastructures such as electrical transmission networks and access roads. Regarding these aspects, the Sechura Desert and the Coast Desert of Peru represent the greatest solar energy hotspots, hence the growth expectations in coming decades will focus on these zones of the country.
Variations in solar radiation with respect to the ENSO climatic phenomenon and the impacts of global climate change must be monitored, and such variations play a key role in the generation of electricity from solar energy [64].
The current progress of solar energy in Peru is incipient, so analysis of the solar photovoltaic (PV) facilities that are in operation and improvements and increases in the number of photovoltaic modules and total installed capacity is in progress (Figure 28). Shortly, it is likely that solar energy companies will provide the opportunity for energy market growth and remote rural electrification, specifically for communities in the Amazon zone. Its use is extremely simple and appropriate for rural electrification, but the main difficulty is its high cost.
Clean-energy sources must be at the forefront of sustainable development policies and international cooperation programs. In this sense, more advances in research are needed concerning the storage of solar energy, such as hydrogen, batteries, and heat storage [65].
Finally, the future of the production of electricity from solar sources considering the portfolio of investments in Peru is promising, with an installed capacity of more than 7218 MW expected to be implemented in the coming years, thus meeting the commitment to carbon neutrality goals by 2050.

5. Conclusions

Peru’s solar resources have been estimated, resulting in a useful potential of 25 GW; this is due to having territory in one of the areas of the world with the highest solar radiation throughout the year. The regions with the greatest solar potential are Arequipa, Moquegua, Tacna, Piura, and Tumbes, with a significant global horizontal irradiation of 5.00 kWh/m2/day on average. Considering the solar photovoltaic facilities currently in operation in Peru, there is a total installed capacity of 398 MW, which is equivalent to 2% of the usable solar energy potential of 25,000 MW (25 GW).
In the case of Peru, the impacts of solar radiation with respect to the ENSO climatic phenomenon and the effects of global climate change must be monitored by experts from academia as research develops.
Therefore, the integration of solar PV facilities into the SEIN has allowed constant technological advances, which have facilitated private investment, training of Peruvian professionals, and job opportunities.
For a country like Peru with topographic barriers and complex geographical conditions, solar energy can generate electricity in rural areas, in the mountains, and in remote places like the Amazon that are not connected to the electrical grid. Despite the development of rural electrification projects using renewable energies, 100% coverage has not yet been achieved. This is mainly due to the low population density in remote areas, which hinders its progress. Here, innovative mechanisms for private investment in the execution of projects with mini-grids and isolated systems must be prioritized, and the approval of the regulations for distributed generation by the Ministry of Energy and Mines is required.
Solar energy for significant power generation will continue to grow gradually, mainly in the north and south of the country, which is why it is estimated that 7.2 GW of installed capacity of PV energy portfolio projects will be implemented in the coming years. However, regulatory modifications are necessary to ensure that solar generating companies can build contracts with free users and distributors of both power and energy, thereby modifying the methodology for calculating firm power for solar plants or opening new markets for the sale of energy by hourly blocks.
Regarding direct normal irradiance (DNI), the values reached in the southern coastal zone are significant, which initially ensures technical feasibility for the development of concentrated solar power (CSP) systems with storage. However, economic conditions hinder their development, and there is also a lack of specific energy regulations and policies for this type of technology. Concentrated solar power (CSP) technology will need more advances in research to guarantee its implementation, including information about the experience of operating the Cerro Dominador concentrating solar facility located in Chile.
Concerning strategic political terms, the government of Peru should implement policies to promote investment in solar energy generation industries, eliminate legal and economic barriers to investors, and incentivize research into new technologies related to solar energy and energy efficiency.
In this scenario, it is possible to conclude that if Peru takes advantage of solar potential by considering a sustainable future perspective and implementing strategic land-use planning, the southern region will be transformed into a world-class territory for renewable energy development considering the hybridization of concentrated solar power (CSP) systems with solar photovoltaic (PV) systems and solar energy storage systems. Also, the hybridization of solar photovoltaic energy with on-shore wind energy appears to be promising, especially in areas where both resources converge, such as the coast of the Ica region.
Finally, Peru contributes to mitigating global climate change, decreasing greenhouse gas (GHG) emissions from the energy generation matrix by considering the implementation of renewable energy with solar photovoltaic facilities. Also, Peru compromises by implementing sustainable development goals (SDGs) and generating a decarbonization economy to guarantee an environmentally friendly planet for future human generations. The enormous solar energy potential of the country, if used adequately and taken advantage of, promises a sustainable future for the development of the local economy, the well-being of communities, and the care of the environment.

Author Contributions

Conceptualization, C.C.; formal analysis, C.C. and X.G.; investigation, C.C., X.G. and E.V.; resources, C.C., X.G. and E.V.; writing—original draft preparation, C.C.; writing—review and editing, C.C., X.G. and E.V.; visualization, C.C., X.G. and E.V.; supervision, E.V. All authors have read and agreed to the published version of the manuscript.

Funding

The research is funded by the Research Department of the Catholic University of Temuco, Chile.

Institutional Review Board Statement

Not applicable.

Informed Consent Statement

Not applicable.

Data Availability Statement

The data presented in this study are available on request from the corresponding author.

Conflicts of Interest

The authors declare no conflicts of interest.

Abbreviations

SDGsSustainable Development Goals
UNUnited Nations
PVPhotovoltaic
CSPConcentrated Solar Power
GHGGreenhouse Gas
CO2eqCarbon Dioxide Equivalent
GDPGross Domestic Product
HDIHuman Development Index
DHIDiffuse Horizontal Irradiance
DNIDirect Normal Irradiance
GHIGlobal Horizontal Irradiance
SEINNational Interconnected Electricity System of Peru
ESMAPEnergy Sector Management Assistance Program
IRENAInternational Renewable Energy Agency
WHOWorld Health Organization
NGOsNon-Government Organizations
CFCapacity Factor
EIAEnvironmental Impact Assessment
MINAMEnvironmental Ministry of Peru
SENAMHIMeteorological and Hydrological National Service of Peru
COESEconomic Operation Committee of the National Interconnected System of Peru
OSINERGMINEnergy Investment Supervisory Agency of Peru
CAPEXCapital Costs
OPEXOperational Costs
AIArtificial Intelligence
MLMachine Learning
CNNsConvolutional Neural Networks
RNNsRecurrent Neural Networks
UAVsUnmanned Aerial Vehicles
RGBRed Green Blue Colors
GISGeographical Information System
RERRenewable Energy Resources
ENSOEl Niño Southern Oscillation
LCOELevelized Cost of Electricity
BESSBattery Energy Storage System
MWMegawatts
GWGigawatts
MWhMegawatts-Hour
GWhGigawatts-Hour
kWh/m2Kilowatt-hour per square meter
kWh/kWKilowatt-hour per Kilowatt
$USDUnited States Dollar
MtonsMillions of tons
HaHectare
maslMeters above sea level

References

  1. Senamhi. Climas del Perú. In Mapa de Clasificación Climática Nacional; Senamhi: Lima, Peru, 2021. [Google Scholar]
  2. World Bank. Repensar el Futuro del Peru Nota de Politica para Transformar al Estado en un Gestor de Bienestar y Desarrollo; World Bank: Washington, DC, USA, 2021. [Google Scholar]
  3. Israel, A.; Herrera, R.J. The governance of Peruvian energy transitions: Path dependence, alternative ideas and change in national hydropower expansion. Energy Res. Soc. Sci. 2020, 69, 101608. [Google Scholar] [CrossRef]
  4. Osinergmin. Información Técnica de Proyectos de Centrales de Generación de Energía Eléctrica Convencionales y No Convencionales con Estudios de Pre Operatividad Aprobados por el Coes; Osinergmin: Lima, Peru, 2022. [Google Scholar]
  5. COES. Informe de la Operación Anual del SEIN–2023; COES: Lima, Peru, 2024. [Google Scholar]
  6. Osinergmin. Energías Renovables Experiencia y Perspectivas en la Ruta del Perú Hacia la Transición Energética; Osinergmin: Lima, Peru, 2019. [Google Scholar]
  7. Giz. Analisis del Potencial y Eventuales Actuales Usos Que Tienen las Fuentes de Energias Alternativas en la Minería Peruana; Samienergy: Lima, Peru, 2021. [Google Scholar]
  8. Cacciuttolo, C.; Cano, D.; Guardia, X.; Villicaña, E. Renewable Energy from Wind Farm Power Plants in Peru: Recent Advances, Challenges, and Future Perspectives. Sustainability 2024, 16, 1589. [Google Scholar] [CrossRef]
  9. López, M.; Veigas, M.; Iglesias, G. On the wave energy resource of Peru. Energy Convers. Manag. 2015, 90, 34–40. [Google Scholar] [CrossRef]
  10. Feron, S.; Cordero, R.R. Is Peru prepared for large-scale sustainable rural electrification? Sustainability 2018, 10, 1683. [Google Scholar] [CrossRef]
  11. Raihan, A.; Tuspekova, A. The nexus between economic growth, renewable energy use, agricultural land expansion, and carbon emissions: New insights from Peru. Energy Nexus 2022, 6, 100067. [Google Scholar] [CrossRef]
  12. Muhammed, G.; Tekbiyik-Ersoy, N. Development of renewable energy in china, usa, and brazil: A comparative study on renewable energy policies. Sustainability 2020, 12, 9136. [Google Scholar] [CrossRef]
  13. Srivastava, S.; Khokhar, F.; Madhav, A.; Pembroke, B.; Shetty, V.; Mutreja, A. COVID-19 lessons for climate change and sustainable health. Energies 2021, 14, 5938. [Google Scholar] [CrossRef]
  14. Wołowiec, T.; Myroshnychenko, I.; Vakulenko, I.; Bogacki, S.; Wiśniewska, A.M.; Kolosok, S.; Yunger, V. International Impact of COVID-19 on Energy Economics and Environmental Pollution: A Scoping Review. Energies 2022, 12, 8407. [Google Scholar] [CrossRef]
  15. Osinergmin. La Industria de la Energía Renovable en el Perú: 10 Años de Contribuciones a la Mitigación del Cambio Climático; Osinergmin: Lima, Peru, 2017. [Google Scholar]
  16. Schlömer, S.; Bruckner, T.; Fulton, L.; Hertwich, E.; McKinnon, A.; Perczyk, D.; Roy, J.; Schaeffer, R.; Sims, R.; Smith, P.; et al. Annex III: Technology-Specific Cost and Performance Parameters. In Climate Change 2014: Mitigation of Climate Change. Contribution of Working Group III to the Fifth Assessment Report of the Intergovernmental Panel on Climate Change; Cambridge University Press: Cambridge, UK, 2014. [Google Scholar]
  17. Israel, A.; Jehling, M. How modern are renewables? The misrecognition of traditional solar thermal energy in Peru’s energy transition. Energy Policy 2019, 133, 110905. [Google Scholar] [CrossRef]
  18. Lucas, H.; del Río, P.; Cabeza, L.F. Stand-alone renewable energy auctions: The case of Peru. Energy Sustain. Dev. 2020, 55, 151–160. [Google Scholar] [CrossRef]
  19. Campodónico, H.; Carrera, C. Energy transition and renewable energies: Challenges for Peru. Energy Policy 2022, 171, 113261. [Google Scholar] [CrossRef]
  20. International Renewable Energy Agency. Future of Solar Photovoltaic: Deployment, Investment, Technology, Grid Integration and Socio-Economic Aspects. 2019, 72p. Available online: https://www.irena.org/-/media/Files/IRENA/Agency/Publication/2019/Nov/IRENA_Future_of_Solar_PV_2019.pdf (accessed on 10 March 2024).
  21. Fernandez-Fuentes, M.H.; Eras-Almeida, A.A.; Egido-Aguilera, M.A. Characterization of technological innovations in photovoltaic rural electrification, based on the experiences of Bolivia, Peru, and Argentina: Third generation solar home systems. Sustainability 2021, 13, 3032. [Google Scholar] [CrossRef]
  22. Franco, M.A.; Groesser, S.N. A systematic literature review of the solar photovoltaic value chain for a circular economy. Sustainability 2021, 13, 9615. [Google Scholar] [CrossRef]
  23. Novas, N.; Garcia, R.M.; Camacho, J.M.; Alcayde, A. Advances in solar energy towards efficient and sustainable energy. Sustainability 2021, 13, 6295. [Google Scholar] [CrossRef]
  24. Ministerio de Energía de Chile. Guía Para la Descripción de Proyectos de Centrales Solares de Generación de Energía Eléctrica en el Seia; Ministerio de Energía de Chile: Santiago, Chile, 2017.
  25. Chala, G.T.; Al Alshaikh, S.M. Solar Photovoltaic Energy as a Promising Enhanced Share of Clean Energy Sources in the Future—A Comprehensive Review. Energies 2023, 16, 7919. [Google Scholar] [CrossRef]
  26. Apeh, O.O.; Meyer, E.L.; Overen, O.K. Contributions of Solar Photovoltaic Systems to Environmental and Socioeconomic Aspects of National Development—A Review. Energies 2022, 15, 5963. [Google Scholar] [CrossRef]
  27. Mohammadi, B.; Moazenzadeh, R. Performance analysis of daily global solar radiation models in peru by regression analysis. Atmosphere 2021, 12, 389. [Google Scholar] [CrossRef]
  28. Senamhi. Atlas de Energía Solar Perú; Senamhi: Lima, Peru, 2003. [Google Scholar]
  29. ESMAP. Global Photovoltaic Power Potential by Country. 2020. Available online: https://solargis.com (accessed on 1 March 2024).
  30. Rios, R.; Duarte, S. Selection of ideal sites for the development of large-scale solar photovoltaic projects through Analytical Hierarchical Process–Geographic information systems (AHP-GIS) in Peru. Renew. Sustain. Energy Rev. 2021, 149, 111310. [Google Scholar] [CrossRef]
  31. Yang, X.; Ji, Y.; Wang, X.; Niu, M.; Long, S.; Xie, J.; Sun, Y. Simplified Method for Predicting Hourly Global Solar Radiation Using Extraterrestrial Radiation and Limited Weather Forecast Parameters. Energies 2023, 16, 3215. [Google Scholar] [CrossRef]
  32. Hasan, M.M.; Hossain, S.; Mofijur, M.; Kabir, Z.; Badruddin, I.A.; Khan, T.M.Y.; Jassim, E. Harnessing Solar Power: A Review of Photovoltaic Innovations, Solar Thermal Systems, and the Dawn of Energy Storage Solutions. Energies 2023, 16, 6456. [Google Scholar] [CrossRef]
  33. Conde, L.A.; Angulo, J.R.; Sevillano-Bendezú, M.; Nofuentes, G.; Töfflinger, J.A.; de la Casa, J. Spectral effects on the energy yield of various photovoltaic technologies in Lima (Peru). Energy 2021, 223, 120034. [Google Scholar] [CrossRef]
  34. Osinergmin. Información Técnica de Proyectos de Centrales de Generación de Energía Eléctrica No Convencional con Estudios de Pre Operatividad Aprobados por el Coes; Osinergmin: Lima, Peru, 2023. [Google Scholar]
  35. Choi, Y. Solar power system planning and design. Appl. Sci. 2020, 10, 367. [Google Scholar] [CrossRef]
  36. Espinoza, R.; Muñoz-Cerón, E.; Aguilera, J.; de la Casa, J. Feasibility evaluation of residential photovoltaic self-consumption projects in Peru. Renew. Energy 2019, 136, 414–427. [Google Scholar] [CrossRef]
  37. Libra, M.; Daneček, M.; Lešetický, J.; Poulek, V.; Sedláček, J.; Beránek, V. Monitoring of defects of a photovoltaic power plant using a drone. Energies 2019, 12, 795. [Google Scholar] [CrossRef]
  38. Liao, K.C.; Wu, H.Y.; Wen, H.T. Using Drones for Thermal Imaging Photography and Building 3D Images to Analyze the Defects of Solar Modules. Inventions 2022, 7, 67. [Google Scholar] [CrossRef]
  39. Starzyński, J.; Zawadzki, P.; Harańczyk, D. Machine Learning in Solar Plants Inspection Automation. Energies 2022, 15, 5966. [Google Scholar] [CrossRef]
  40. Alzain, E.; Al-Otaibi, S.; Aldhyani, T.H.H.; Alshebami, A.S.; Almaiah, M.A.; Jadhav, M.E. Revolutionizing Solar Power Production with Artificial Intelligence: A Sustainable Predictive Model. Sustainability 2023, 15, 7999. [Google Scholar] [CrossRef]
  41. Puga-Gil, D.; Astray, G.; Barreiro, E.; Gálvez, J.F.; Mejuto, J.C. Global Solar Irradiation Modelling and Prediction Using Machine Learning Models for Their Potential Use in Renewable Energy Applications. Mathematics 2022, 10, 4746. [Google Scholar] [CrossRef]
  42. Maniscalco, M.P.; Longo, S.; Miccichè, G.; Cellura, M.; Ferraro, M. A Critical Review of the Environmental Performance of Bifacial Photovoltaic Panels. Energies 2024, 17, 226. [Google Scholar] [CrossRef]
  43. Soltec. Bifacial PV Panels; Soltec: Murcia, Spain, 2019. [Google Scholar]
  44. Zhang, H.L.; Baeyens, J.; Degrève, J.; Cacères, G. Concentrated solar power plants: Review and design methodology. Renew. Sustain. Energy Rev. 2013, 22, 466–481. [Google Scholar] [CrossRef]
  45. Corona, B.; Ruiz, D.; San Miguel, G. Life cycle assessment of a HYSOL concentrated solar power plant: Analyzing the effect of geographic location. Energies 2016, 9, 413. [Google Scholar] [CrossRef]
  46. Cáceres, G.; Anrique, N.; Girard, A.; Degrève, J.; Baeyens, J.; Zhang, H.L. Performance of molten salt solar power towers in Chile. J. Renew. Sustain. Energy 2013, 5, 23–30. [Google Scholar] [CrossRef]
  47. Larraín, T.; Escobar, R. Net energy analysis for concentrated solar power plants in northern Chile. Renew. Energy 2012, 41, 123–133. [Google Scholar] [CrossRef]
  48. Starke, A.R.; Cardemil, J.M.; Escobar, R.A.; Colle, S. Assessing the performance of hybrid CSP + PV plants in northern Chile. Sol. Energy 2016, 138, 88–97. [Google Scholar] [CrossRef]
  49. Dale, M. A comparative analysis of energy costs of photovoltaic, solar thermal, and wind electricity generation technologies. Appl. Sci. 2013, 3, 325–337. [Google Scholar] [CrossRef]
  50. Álvarez Vera, A. Development of Technical-Economic Scenarios for the Incorporation of AN SPT-TES + PV Hybrid Power Plant in The South of Peru. 2021. Available online: https://repositorio.utec.edu.pe/handle/20.500.12815/239 (accessed on 7 May 2024).
  51. Lillo, P.; Ferrer-Martí, L.; Juanpera, M. Strengthening the sustainability of rural electrification projects: Renewable energy, management models and energy transitions in Peru, Ecuador and Bolivia. Energy Res. Soc. Sci. 2021, 80, 102222. [Google Scholar] [CrossRef]
  52. García, D.W. Trading solar panels for grid power: An ethnography of rural energy service in Peru. J. Rural Stud. 2020, 78, 254–261. [Google Scholar] [CrossRef]
  53. Riojas-Díaz, K.; Jaramillo-Romero, R.; Calderón-Vargas, F.; Asmat-Campos, D. Sustainable Tourism and Renewable Energy’s Potential: A Local Development Proposal for the La Florida Community, Huaral, Peru. Economies 2022, 10, 47. [Google Scholar] [CrossRef]
  54. Juanpera, M.; Domenech, B.; Ferrer-Martí, L.; Garzón, A.; Pastor, R. Renewable-based electrification for remote locations. Does short-term success endure over time? A case study in Peru. Renew. Sustain. Energy Rev. 2021, 146, 111–127. [Google Scholar] [CrossRef]
  55. Lillo, P.; Ferrer-Martí, L.; Boni, A.; Fernández-Baldor, Á. Assessing management models for off-grid renewable energy electrification projects using the Human Development approach: Case study in Peru. Energy Sustain. Dev. 2015, 25, 17–26. [Google Scholar] [CrossRef]
  56. Calderón-Vargas, F.; Asmat-Campos, D.; Chávez-Arroyo, P. Sustainable tourism policies in Peru and their link with renewable energy: Analysis in the main museums of the Moche route. Heliyon 2021, 7, 111177. [Google Scholar] [CrossRef] [PubMed]
  57. Vyhmeister, E.; Aleixendri Muñoz, C.; Bermúdez Miquel, J.M.; Pina Moya, J.; Fúnez Guerra, C.; Rodríguez Mayor, L.; Godoy-Faúndez, A.; Higueras, P.; Clemente-Jul, C.; Valdés-González, H.; et al. A combined photovoltaic and novel renewable energy system: An optimized techno-economic analysis for mining industry applications. J. Clean. Prod. 2017, 149, 999–1010. [Google Scholar] [CrossRef]
  58. Seminario-Córdova, R. Latin America towards Sustainability through Renewable Energies: A Systematic Review. Energies 2023, 16, 7422. [Google Scholar] [CrossRef]
  59. Murray, C.; Platzer, W.; Petersen, J. Potential for solar thermal energy in the heap bioleaching of chalcopyrite in Chilean copper mining. Miner. Eng. 2017, 100, 75–82. [Google Scholar] [CrossRef]
  60. Ortega, A.; Escobar, R.; Colle, S.; de Abreu, S.L. The state of solar energy resource assessment in Chile. Renew. Energy 2010, 35, 2514–2524. [Google Scholar] [CrossRef]
  61. Nasirov, S.; Silva, C.; Agostini, C.A. Assessment of barriers and opportunities for renewable energy development in Chile. Energy Sources Part B Econ. Plan. Policy 2016, 11, 150–156. [Google Scholar] [CrossRef]
  62. Fernández, Á.G.; Gomez-Vidal, J.C. Thermophysical properties of low cost lithium nitrate salts produced in northern Chile for thermal energy storage. Renew. Energy 2017, 101, 120–125. [Google Scholar] [CrossRef]
  63. Parrado, C.; Girard, A.; Simon, F.; Fuentealba, E. 2050 LCOE (Levelized Cost of Energy) projection for a hybrid PV (photovoltaic)-CSP (concentrated solar power) plant in the Atacama Desert, Chile. Energy 2016, 94, 422–430. [Google Scholar] [CrossRef]
  64. Bhatt, U.S.; Carreras, B.A.; Barredo, J.M.R.; Newman, D.E.; Collet, P.; Gomila, D. The Potential Impact of Climate Change on the Efficiency and Reliability of Solar, Hydro, and Wind Energy Sources. Land 2022, 11, 1275. [Google Scholar] [CrossRef]
  65. Falcone, P.M. Sustainable Energy Policies in Developing Countries: A Review of Challenges and Opportunities. Energies 2023, 16, 6682. [Google Scholar] [CrossRef]
Figure 1. Some examples of the available potential of renewable energies in some regions of Peru. Note: North Zone—wind potential, Central Zone—hydropower potential, South Zone—solar potential [6].
Figure 1. Some examples of the available potential of renewable energies in some regions of Peru. Note: North Zone—wind potential, Central Zone—hydropower potential, South Zone—solar potential [6].
Sustainability 16 04388 g001
Figure 2. Schematical view of a functioning solar photovoltaic (PV) facility. Adapted from [24].
Figure 2. Schematical view of a functioning solar photovoltaic (PV) facility. Adapted from [24].
Sustainability 16 04388 g002
Figure 3. Rubi solar photovoltaic facility, located in a desert landscape in Peru.
Figure 3. Rubi solar photovoltaic facility, located in a desert landscape in Peru.
Sustainability 16 04388 g003
Figure 4. Solar resource map—Global Horizontal Irradiation (GHI) registered in Peru. Adapted from [29].
Figure 4. Solar resource map—Global Horizontal Irradiation (GHI) registered in Peru. Adapted from [29].
Sustainability 16 04388 g004
Figure 5. Maps of adequate solar photovoltaic (PV) technical potential in Peru. Adapted from [30].
Figure 5. Maps of adequate solar photovoltaic (PV) technical potential in Peru. Adapted from [30].
Sustainability 16 04388 g005
Figure 6. Average hourly solar energy generation registered during the summer season in Peru in 2019 [6].
Figure 6. Average hourly solar energy generation registered during the summer season in Peru in 2019 [6].
Sustainability 16 04388 g006
Figure 7. Average hourly solar energy generation registered during the winter season in Peru in 2019 [6].
Figure 7. Average hourly solar energy generation registered during the winter season in Peru in 2019 [6].
Sustainability 16 04388 g007
Figure 8. Variation in energy production (GWh) during a year in some solar photovoltaic (PV) facilities in Peru [6].
Figure 8. Variation in energy production (GWh) during a year in some solar photovoltaic (PV) facilities in Peru [6].
Sustainability 16 04388 g008
Figure 9. Rubi solar photovoltaic facility located in a desert landscape in Peru.
Figure 9. Rubi solar photovoltaic facility located in a desert landscape in Peru.
Sustainability 16 04388 g009
Figure 10. Landscape showing photovoltaic panels in the Repartición solar facility.
Figure 10. Landscape showing photovoltaic panels in the Repartición solar facility.
Sustainability 16 04388 g010
Figure 11. Landscape showing photovoltaic panels in the Majes solar facility.
Figure 11. Landscape showing photovoltaic panels in the Majes solar facility.
Sustainability 16 04388 g011
Figure 12. Landscape showing photovoltaic panels in the Tacna solar facility.
Figure 12. Landscape showing photovoltaic panels in the Tacna solar facility.
Sustainability 16 04388 g012
Figure 13. Landscape showing photovoltaic panels in the Panamericana solar facility.
Figure 13. Landscape showing photovoltaic panels in the Panamericana solar facility.
Sustainability 16 04388 g013
Figure 14. Landscape showing photovoltaic panels in the Moquegua FV solar facility.
Figure 14. Landscape showing photovoltaic panels in the Moquegua FV solar facility.
Sustainability 16 04388 g014
Figure 15. Landscape showing photovoltaic panels in the Intipampa solar facility.
Figure 15. Landscape showing photovoltaic panels in the Intipampa solar facility.
Sustainability 16 04388 g015
Figure 16. Landscape showing photovoltaic panels in the Rubi solar facility.
Figure 16. Landscape showing photovoltaic panels in the Rubi solar facility.
Sustainability 16 04388 g016
Figure 17. Landscape showing photovoltaic panels in the Clemesi solar facility.
Figure 17. Landscape showing photovoltaic panels in the Clemesi solar facility.
Sustainability 16 04388 g017
Figure 18. Landscape showing photovoltaic panels in the Yarucaya solar facility.
Figure 18. Landscape showing photovoltaic panels in the Yarucaya solar facility.
Sustainability 16 04388 g018
Figure 19. Percentage of electrical energy generated by solar photovoltaic facility sources in Peru.
Figure 19. Percentage of electrical energy generated by solar photovoltaic facility sources in Peru.
Sustainability 16 04388 g019
Figure 20. Annual energy production and capacity factor of solar photovoltaic facilities in Peru.
Figure 20. Annual energy production and capacity factor of solar photovoltaic facilities in Peru.
Sustainability 16 04388 g020
Figure 21. Evolution (years) of the solar photovoltaic installed capacity (MW) in Peru.
Figure 21. Evolution (years) of the solar photovoltaic installed capacity (MW) in Peru.
Sustainability 16 04388 g021
Figure 22. Landscape showing the San Martin solar photovoltaic facility under construction.
Figure 22. Landscape showing the San Martin solar photovoltaic facility under construction.
Sustainability 16 04388 g022
Figure 23. Landscape showing the Lupi solar photovoltaic facility under construction.
Figure 23. Landscape showing the Lupi solar photovoltaic facility under construction.
Sustainability 16 04388 g023
Figure 24. Landscape showing the Matarani solar photovoltaic facility under construction.
Figure 24. Landscape showing the Matarani solar photovoltaic facility under construction.
Sustainability 16 04388 g024
Figure 26. Schematical view of the functioning of bifacial solar photovoltaic panels [43].
Figure 26. Schematical view of the functioning of bifacial solar photovoltaic panels [43].
Sustainability 16 04388 g026
Figure 27. Schematic view of a concentrated solar power (CSP) plant. Adapted from [24].
Figure 27. Schematic view of a concentrated solar power (CSP) plant. Adapted from [24].
Sustainability 16 04388 g027
Figure 28. Sunset over the Rubi solar PV facility, which has enormous solar potential waiting for sustainable use.
Figure 28. Sunset over the Rubi solar PV facility, which has enormous solar potential waiting for sustainable use.
Sustainability 16 04388 g028
Table 1. Status of implementation of renewable energy in Peru in 2023.
Table 1. Status of implementation of renewable energy in Peru in 2023.
Renewable EnergyInstalled Capacity (MW)Usable Potential (MW)Percentage of
Resources Used
References
Hydroelectric
(Conventional > 20 MW)
4748.3770,0007.23%[6]
Hydroelectric
(Non-Conventional < 20 MW)
319.28
On-shore Wind668.0020,5003.26%[8]
Solar398.0725,0001.59%[4]
Biomass66.0045014.67%[6]
Geothermal0.0028600.00%[6]
Off-shore Wind0.00347,0000.00%[8]
Waves0.0035000.00%[9]
Tidal (Currents and Range)0.00Not determined0.00%[9]
Total6199.72469,3101.32%
Table 2. Geographical areas of Peru with the greatest average daily solar energy [6].
Table 2. Geographical areas of Peru with the greatest average daily solar energy [6].
RegionDaily Solar Energy–Solar Irradiance (kWh/m2/day)
Arequipa5.2 min–7.0 max; Average 6.08
Moquegua4.9 min–6.9 max; Average 6.04
Tacna5.2 min–7.0 max; Average 5.83
Tumbes4.0 min–6.1 max; Average 5.67
Piura4.8 min–6.4 max; Average 5.54
Ica5.3 min–6.7 max; Average 5.50
Table 3. Main characteristics of the Repartición solar photovoltaic facility [4].
Table 3. Main characteristics of the Repartición solar photovoltaic facility [4].
SpecificationDataUnits
Project ZoneArequipa Region-
Energy CompanyGTS Reparición S.A.C. T-Solar-
Type of Solar FacilityPhotovoltaic-
Quantities of PV Modules58,000-
Module TypePolycrystalline silicon-
Power of Modules350W
Number of Inverters32-
Type of Structure1-axis horizontal tracker-
Tracking Angle45°
Installed Capacity20MW
Capacity Factor0.25-
Table 4. Main characteristics of the Majes solar photovoltaic facility [4].
Table 4. Main characteristics of the Majes solar photovoltaic facility [4].
SpecificationDataUnits
Project ZoneArequipa Region-
Energy CompanyGTS Majes S.A.C. T-Solar-
Type of Solar FacilityPhotovoltaic-
Quantities of PV Modules58,000-
Module TypePolycrystalline silicon-
Power of Modules350W
Number of Inverters32-
Type of Structure1-axis horizontal tracker-
Tracking Angle45°
Installed Capacity20MW
Capacity Factor0.26-
Table 5. Main characteristics of the Tacna solar photovoltaic facility [4].
Table 5. Main characteristics of the Tacna solar photovoltaic facility [4].
SpecificationDataUnits
Project ZoneTacna Region-
Energy CompanyTacna Solar S.A.C. Solarpack-
Type of Solar FacilityPhotovoltaic-
Quantities of PV Modules58,000-
Module TypePolycrystalline silicon-
Power of Modules350W
Number of Inverters32-
Type of Structure1-axis horizontal tracker-
Tracking Angle50°
Installed Capacity20MW
Capacity Factor0.30-
Table 6. Main characteristics of the Panamericana solar photovoltaic facility [4].
Table 6. Main characteristics of the Panamericana solar photovoltaic facility [4].
SpecificationDataUnits
Project ZoneMoquegua Region-
Energy CompanyPanamericana Solar S.A.C. Solarpack-
Type of Solar FacilityPhotovoltaic-
Quantities of PV Modules58,000-
Module TypePolycrystalline silicon-
Power of Modules350W
Number of Inverters32-
Type of Structure1-axis horizontal tracker-
Tracking Angle55°
Installed Capacity20MW
Capacity Factor0.33-
Table 7. Main characteristics of the Moquegua FV solar photovoltaic facility [4].
Table 7. Main characteristics of the Moquegua FV solar photovoltaic facility [4].
SpecificationDataUnits
Project ZoneMoquegua Region-
Energy CompanyMoquegua FV S.A.C. Solarpack-
Type of Solar FacilityPhotovoltaic-
Quantities of PV Modules58,000-
Module TypePolycrystalline silicon-
Power of Modules280W
Number of Inverters26-
Type of Structure1-axis horizontal tracker-
Tracking Angle55°
Installed Capacity16MW
Capacity Factor0.34-
Table 8. Main characteristics of the Intipampa solar photovoltaic facility [4].
Table 8. Main characteristics of the Intipampa solar photovoltaic facility [4].
SpecificationDataUnits
Project ZoneMoquegua Region-
Energy CompanyEngie Energía Perú S.A.-
Type of Solar FacilityPhotovoltaic-
Quantities of PV Modules125,000-
Module TypePolycrystalline silicon-
Power of Modules325W
Number of Inverters18-
Type of Structure1-axis horizontal tracker-
Tracking Angle55°
Installed Capacity40MW
Capacity Factor0.27-
Table 9. Main characteristics of the Rubi solar photovoltaic facility [4].
Table 9. Main characteristics of the Rubi solar photovoltaic facility [4].
SpecificationDataUnits
Project ZoneMoquegua Region-
Energy CompanyEnel Green Perú S.A.-
Type of Solar FacilityPhotovoltaic-
Quantities of PV Modules450,000-
Module TypePolycrystalline silicon-
Power of Modules320W
Number of Inverters164-
Type of Structure1-axis horizontal tracker-
Tracking Angle45°
Installed Capacity144MW
Capacity Factor0.35-
Table 10. Main characteristics of the Clemesi solar photovoltaic facility [4].
Table 10. Main characteristics of the Clemesi solar photovoltaic facility [4].
SpecificationDataUnits
Project ZoneMoquegua Region-
Energy CompanyEnel Green Perú S.A.-
Type of Solar FacilityPhotovoltaic-
Quantities of PV Modules221,000-
Module TypeMonocrystalline silicon-
Power of Modules525W
Number of Inverters132-
Type of Structure1-axis horizontal tracker-
Tracking Angle50°
Installed Capacity116.45MW
Capacity Factor0.35-
Table 11. Main characteristics of the Yarucaya solar photovoltaic facility [4].
Table 11. Main characteristics of the Yarucaya solar photovoltaic facility [4].
SpecificationDataUnits
Project ZoneLima Region-
Energy CompanyColca Solar S.A.C.-
Type of Solar FacilityPhotovoltaic-
Quantities of PV Modules3070-
Module TypePolycrystalline silicon-
Power of Modules530W
Number of Inverters7-
Type of Structure1-axis horizontal tracker-
Tracking Angle45°
Installed Capacity1.62MW
Capacity Factor0.22-
Table 12. Solar photovoltaic facilities functioning in Peru as of March 2024.
Table 12. Solar photovoltaic facilities functioning in Peru as of March 2024.
#Name of Solar Photovoltaic FacilityRegionEnergy CompanyInstalled Capacity (MW)
1Central Solar ReparticiónArequipaGTS Repartición S.A.C. T-Solar20
2Central Solar MajesArequipaGTS Majes S.A.C. T-Solar20
3Central Solar Tacna SolarTacnaTacna Solar S.A.C. Solarpack20
4Central Solar Panamericana SolarMoqueguaPanamericana Solar S.A.C. Solarpack20
5Central Solar Moquegua FVMoqueguaMoquegua FV S.A.C. Solarpack16
6Central Solar IntipampaMoqueguaEngie Energía Perú S.A.40
7Central Solar RubiMoqueguaEnel Green Power Perú S.A.144
8Central Solar ClemesiMoqueguaEnel Green Power Perú S.A.116.45
9Central Solar YarucayaLimaColca Solar S.A.C.1.62
Total Installed Capacity398.07
Table 13. Main characteristics of the San Martin solar photovoltaic facility [4].
Table 13. Main characteristics of the San Martin solar photovoltaic facility [4].
SpecificationDataUnits
Project ZoneMoquegua Region-
Energy CompanyKallpa Generación S.A.C.-
Type of Solar FacilityPhotovoltaic-
Quantities of PV Modules1,000,000-
Module TypePolycrystalline silicon-
Power of Modules300W
Number of Inverters150-
Type of Structure1-axis horizontal tracker-
Tracking Angle50°
Installed Capacity300MW
Capacity Factor0.40-
Table 14. Main characteristics of the Lupi solar photovoltaic facility [4].
Table 14. Main characteristics of the Lupi solar photovoltaic facility [4].
SpecificationDataUnits
Project ZoneMoquegua Region-
Energy CompanyStatkraft Perú S.A.C.-
Type of Solar FacilityPhotovoltaic-
Quantities of PV Modules470,000-
Module TypeCrystalline silicon-
Power of Modules320W
Number of Inverters68-
Type of Structure1-axis horizontal tracker-
Tracking Angle45°
Installed Capacity150MW
Capacity Factor0.32-
Table 15. Main characteristics of the Matarani solar photovoltaic facility [4].
Table 15. Main characteristics of the Matarani solar photovoltaic facility [4].
SpecificationDataUnits
Project ZoneArequipa Region-
Energy CompanyYinson Renewables S.A.C.-
Type of Solar FacilityPhotovoltaic-
Quantities of PV Modules123,500-
Module TypePolycrystalline silicon-
Power of Modules650W
Number of Inverters56-
Type of Structure1-axis horizontal tracker-
Tracking Angle40°
Installed Capacity80MW
Capacity Factor0.35-
Table 16. Solar photovoltaic facilities under construction in Peru as of March 2024 [34].
Table 16. Solar photovoltaic facilities under construction in Peru as of March 2024 [34].
#Name of Solar Photovoltaic FacilityRegionEnergy CompanyInstalled Capacity (MW)
1Central Solar San MartinArequipaKallpa Generación S.A.C.300
2Central Solar LupiMoqueguaStatkraft Perú S.A.C.150
3Central Solar MataraniArequipaYinson Renewables S.A.C.80
Total Projected Capacity530
Table 17. Solar photovoltaic facilities in Peru projected for the period 2024–2028 [4].
Table 17. Solar photovoltaic facilities in Peru projected for the period 2024–2028 [4].
#Name of Solar Photovoltaic FacilityRegionEnergy CompanyInstalled Capacity (MW)
1Central Solar Continua Pichu PichuArequipaCSF Continua Pichu Pichu S.A.C.60
2Central Solar Continua ChachaniArequipaCSF Continua Chachani S.A.C.100
3Central Solar Continua MistiArequipaCSF Continua Misti S.A.C.300
4Central Solar Alto de Alianza ITacnaAtria Energía S.A.C.300
5Central Solar Alto de Alianza IIMoqueguaAtria Energía S.A.C.300
6Central Solar SuniloMoqueguaEnel Green Power Perú S.A.120
7Central Solar YuramayoArequipaEmpresa de Generación Eléctrica Yuramayo245
8Central Solar HuarajonePunoContinua Energía Positivas S.A.C.200
9Central Solar IllaArequipaEnergía Renovable La Joya S.A.385
10Central Solar Santa Isabel ITacnaProdiel Perú S.A.100
11Central Solar Santa Isabel IITacnaProdiel Perú S.A.100
12Central Solar Illari NorteArequipaEnel Green Power Perú S.A.112
13Central Solar Illari SurArequipaEnel Green Power Perú S.A.312
14Central Solar SolimanaArequipaCelepsa250
15Central Solar SunnyArequipaKallpa Generación204
16Central Solar Sol de Verano IArequipaMajes Sol de Verano S.A.C.45
17Central Solar Sol de Verano IIPunoVerano Capital Perú S.A.C.93
18Central Solar Sol de Verano IIIArequipaVerano Capital Perú S.A.C.600
19Central Solar Ruta del SolMoqueguaEnel Green Power Perú S.A.308
20Central Solar RuphayArequipaEngie Energía Perú S.A.93
21Central Solar HanaqpampaMoqueguaEngie Energía Perú S.A.300
22Central Solar El AltoMoqueguaBlaud Energy Perú S.A.C.76
23Central Solar La BanderaTacnaBlaud Energy Perú S.A.C.120
24Central Solar Sol de TalaraPiuraLader Energy Chile SPA200
25Central Solar WindicaIcaFener Perú S.A.25
26Central Solar Sol de Los AndesArequipaLader Energy Chile SPA250
27Central Solar ChalhuancaArequipaTre Perú S.A.C.106
28Central Solar Alba SolarArequipaIgnis Partners S.L.200
29Central Solar CoralMoqueguaIgnis Partners S.L.403
30Central Solar Sumac Nina IArequipaEnel Green Power Perú S.A.447
31Central Solar Rubi V Fase IMoqueguaEnel Green Power Perú S.A.332
32Central Solar Rubi V Fase IIMoqueguaEnel Green Power Perú S.A.332
33Central Solar Blanca SolarArequipaIgnis Partners S.L.200
Total Projected Capacity7218
Table 18. Potentialities and limitations of solar photovoltaic facilities according to the knowledge acquired in Peru.
Table 18. Potentialities and limitations of solar photovoltaic facilities according to the knowledge acquired in Peru.
PotentialitiesLimitations
  • Solar energy is an excellent clean-energy source because there is no air pollution when used.
  • Peru has high solar radiation due to its geographical location, with close to 25 GW of usable power.
  • The areas of greatest solar radiation coincide with areas with a main electrical network of 550 kV, 220 kV, and 138 kV, which allows the extraction of energy from the southern area.
  • Large industrial-scale solar PV projects can require large areas of land (hectares).
  • The initial investment costs (CAPEX) for the installation of photovoltaic solar energy can be high compared with other alternatives.
  • In some places, like the north of Peru, solar radiation does not have the intensity or is not sufficiently constant throughout the year, for example, due to the presence of clouds; therefore, a permanent flow of energy may not always be provided.
  • Solar energy is a practically unlimited renewable resource. The average daily solar window in Peru is between 9 and 11 h a day, which allows for steady electricity production from 6:00 a.m. to 5:00 p.m.
  • It generates a large number of jobs, mainly in the construction process.
  • The places where there is the greatest radiation are deserts and remote places, where it is difficult to harness the energy to develop agricultural or industrial activity.
  • Solar photovoltaic (PV) energy can be stored, but it may be costly. Nowadays, there are several methods to store solar photovoltaic (PV) energy ranging from lithium batteries to pumped hydro.
  • It has a low exploitation or OPEX. The only cost linked with the implementation of solar energy is the cost of manufacturing the components and installation. After the CAPEX there are no other costs linked with its use. The reduction of LCOE from 2010 ($USD 212 MWh) to 2018 ($USD 48 MWh) allowed rapid implementation in the SEIN.
  • Sometimes, owing the El Niño Southern Oscillation (ENSO), it is not possible to generate power during 9 or 11 h because of the microclimates and it is only feasible for 7 or 8 h of the day on average.
  • The photovoltaic industry (manufacturing) requires certain processes that can have negative environmental impacts, such as the emission of greenhouse gases (GHG) and waste generation.
  • Photovoltaic power systems are designed to be flexible and expandable.
  • Dirty photovoltaic panels due to dust storms that occur in the desert landscape reduce energy production by up to 8%.
  • Photovoltaic solar energy can be implemented in remote places such as deserts.
  • The operation of photovoltaic solar energy facilities does not generate noise.
  • Photovoltaic solar energy can be easily hybridized with other technologies.
  • Although solar photovoltaic (PV) systems can have storage systems, the BESS technology, due to its high cost, reduced or non-existent technical regulations for connection in the SEIN, and variations in marginal costs in the spot market, makes them unviable in Peru in the medium term.
Table 19. Characteristics of concentrated solar power (CSP) technologies considering the site-specific conditions of Peru [50].
Table 19. Characteristics of concentrated solar power (CSP) technologies considering the site-specific conditions of Peru [50].
CharacteristicsParabolic Trough
Collector
Linear Fresnel
Reflector
Solar Power
Tower
Parabolic
Dish Systems
Area Requirement (m2/MWh)4–66–88–1230–40
Thermal Efficiency30–40%-30–40%30–40%
Plant Peak Efficiency14–20%18%23–35%30%
Direct Normal Irradiance (DNI)1800–2000 kWh/m2
Water Requirement (m3/MWh)5.403.204.250.15
Operation Temperature of Solar Field (°C)290–550250–560250–650800
Grid StabilityMedium to HighMediumHighLow
Storage PossibilityYesYesYesDepends on plant configuration
Heat Transfer FluidSynthetic Oil, Water/SteamWater/SteamWater/Steam, Molten SaltAir, H2, He
Technology Development RiskLowMediumMediumMedium
Possibilities of Implementation in PeruHighLowMediumLow
Possibilities of Hybridization with other Energy TechnologiesPhotovoltaic,
Geothermal,
Natural Gas
Natural GasPhotovoltaic,
Geothermal,
Natural Gas
Natural Gas
Disclaimer/Publisher’s Note: The statements, opinions and data contained in all publications are solely those of the individual author(s) and contributor(s) and not of MDPI and/or the editor(s). MDPI and/or the editor(s) disclaim responsibility for any injury to people or property resulting from any ideas, methods, instructions or products referred to in the content.

Share and Cite

MDPI and ACS Style

Cacciuttolo, C.; Guardia, X.; Villicaña, E. Implementation of Renewable Energy from Solar Photovoltaic (PV) Facilities in Peru: A Promising Sustainable Future. Sustainability 2024, 16, 4388. https://doi.org/10.3390/su16114388

AMA Style

Cacciuttolo C, Guardia X, Villicaña E. Implementation of Renewable Energy from Solar Photovoltaic (PV) Facilities in Peru: A Promising Sustainable Future. Sustainability. 2024; 16(11):4388. https://doi.org/10.3390/su16114388

Chicago/Turabian Style

Cacciuttolo, Carlos, Ximena Guardia, and Eunice Villicaña. 2024. "Implementation of Renewable Energy from Solar Photovoltaic (PV) Facilities in Peru: A Promising Sustainable Future" Sustainability 16, no. 11: 4388. https://doi.org/10.3390/su16114388

Note that from the first issue of 2016, this journal uses article numbers instead of page numbers. See further details here.

Article Metrics

Back to TopTop