1. Introduction
With global energy saving and carbon reduction in full swing, industries with high energy consumption and emissions, including transportation sector, are under significant pressure to utilize green practices, especially in the realm of road transportation. In 2021, greenhouse gas (GHG) emissions from road transportation in the United States accounted for 82.7% of the total emissions within the transportation sector [
1]. In China, this proportion is similarly high, reaching 79.2% [
2]. GHG emissions caused by traffic congestion, especially the freeway congestion, are huge owing to the prolonged idling and the frequent acceleration and deceleration [
3]. Previous studies have indicated that, in 2020, additional fuel consumption due to traffic congestion in the United States reached 1.7 billion gallons, resulting in an additional 18 million tons of greenhouse gas emissions [
4]. Among these, traffic accidents on freeways are one of the primary causes of temporary congestion. Existing research shows that episodic traffic congestion caused by freeway incidents, such as traffic accidents and vehicle breakdowns, accounts for 50% to 75% of the overall traffic congestion [
5].
There are already several strategies to reduce the external impact of road accidents, including accident warning, traffic incident management [
6,
7], intelligent speed adaptation [
6,
8], etc. One of the key objectives for these strategies is to reduce the external impact of accidents on the traffic operations as much as possible through rapid accident emergency response. In other words, the accident management duration should be minimized through a series of efficient steps: accident identification, strategy generation, accident report recording, field cleanup, accident lane closure/re-open, etc. Considering the significant traffic congestion and vehicle emission impact from accidents, an efficient method is necessary to quantify such impact under various operation scenarios, in a way that offers guidance on the accident management goal for CO
2 emission reduction.
There are now several methods to quantify the vehicle CO
2 emission impact of road accidents, such as survival analysis methods [
9], MEET model [
10], impact factor method [
11], standard driving schedule matching [
12], etc. These do not quantify the external impacts of incident management scenarios on CO
2 emissions in a very comprehensive way. Some studies have simply established the relationship between emissions and the average speed of the scenario [
6,
10], or simply assessed the impact of accidents in terms of traffic volume [
11]. These models do not build the connection between emissions and accident management index (e.g., accident management duration, etc.) and are thus difficult to use for measure evaluation or comparison analysis. Existing research has delved into establishing the connection between additional emissions resulting from highway accidents and accident management strategies [
13]. Nonetheless, there are notable outstanding issues within this body of research that warrant further investigation. However, this study included service level as an independent variable, which shares a significant correlation with other independent variables like incident processing time and the number of lanes. Additionally, the study encountered limitations in terms of data sample size and proposed only a lookup table approach for predicting accidental carbon emissions. To address these limitations and build upon the existing literature, our study seeks to establish a statistical relationship between additional emissions caused by highway accidents and variables such as incident handling time, traffic volume, number of lanes, and vehicle model composition using VISSIM. This approach aims to overcome challenges related to sample size insufficiency and inadequate model applicability observed in prior studies.
Modeling requires the consideration of model complexity, accuracy, and robustness. For such a model, selecting the right predictors is critical. For accident emission reduction, the most common measure is to improve the efficiency of accident treatment in order to reduce the treatment time and the congestion duration. Although traffic accidents can lead to increased emissions due to congestion, it has been shown that efficient and rapid responses to the incidents lead to the reduction in this externality [
9]. Therefore, accident duration is added to the model variables to enable the evaluation of accident management measures. In addition, there are also very significant effects of vehicle composition [
10,
12] and traffic demand [
6] on traffic CO
2 emissions. This paper proposes a model that balances data accessibility, model complexity, accuracy, and robustness to predict additional CO
2 emissions (the difference between the total CO
2 emissions of the scenario with an accident and the total CO
2 emissions of the scenario without an accident (with an accident duration of 0 min) under identical conditions) caused by accidents under various operation and vehicle composition scenarios. Moreover, the focus of the model is to quantify reductions in emissions resulting from various accident management durations. As for now, the study focused only on single-lane-occupancy accidents.
With the advancement of microscopic traffic simulation software technology (VISSIM, AnyLogic, etc.), some studies have proposed to use them to analyze the operation impact of traffic accidents by simulating traffic flow under multiple scenarios [
12,
13,
14,
15]. And traffic simulation software also enables the output of vehicle trajectories that captures the detailed interruption of traffic operations from different types and accidents in a wide impact range. The current microsimulation software (VISSIM, AnyLogic, etc.) can effectively capture the driving behaviors of vehicles following a traffic accident within microscopic traffic flow scenarios. Moreover, compared to real-world data, the microsimulation software demonstrates its capability to efficiently and accurately acquire traffic flow data across a spectrum of accident scenarios.
A suitable emission model should be chosen to perform emission calculations and reflect the traffic flow characteristics from the simulation. The selection of an emission model to acquire vehicle emissions data stems from the considerable challenge of obtaining comprehensive emissions data across various accident scenarios, which is essential to support statistical modeling effectively. Fortunately, numerous established emission models exhibit proven accuracy and robustness through extensive validation in numerous studies. Therefore, leveraging mature emission models to compute vehicle emissions for subsequent modeling in this manner is both practical and feasible. There are already many emission models available, such as MOVES [
16], CMEM [
17], and PERE [
18]. MOVES is now one of the most widely used emission models. In MOVES, emission predictions can be made by using the default driving cycles in the model [
12]. Alternatively, emission factors for predicting are available by different driving operating mode bins [
19]. As for the simulation data, vehicle second-by-second speed and acceleration data are readily available, which can be used to capture the vehicle’s operating modes. Therefore, in this study, the aforementioned attributes of MOVES (version: MOVES3) can be utilized to acquire the second-by-second vehicle emission data for each simulation scenario, using the second-by-second vehicle operation results provided by VISSIM (version: PTV VISSIM 7.00-02 [49473]).
This study used a nonlinear regression model for fitting based on the actual relationship between emissions and these predictors. For nonlinear regression, generalized additive models (GAM) and polynomial regression are common (others are either similar or not applicable). GAM is an automatic method of fitting a spline regression and does not require the specification of knots for the spline. It minimizes the residuals by assigning different spline functions to each variable. And the spline function fits the data points by computing a polynomial regression between each knot [
20]. GAM tends to have a higher precision of fit than simple linear regression or polynomial regression and is a good method of choice for various research. However, high level of precision often leads to overfitting. And more importantly, GAM is a nonparametric model. This means that the resulting model cannot decipher the physical meaning of the parameters like a parametric model, which this study is looking for. Thus, polynomial regression and variable transformation are chosen for model fitting.
Based on the above requirements, the study uses VISSIM and MOVES to simulate the effect of the accident duration (including accident occurrence, response, management, and resumption) on freeways CO2 emissions under various vehicle compositions, traffic demands, and number of lanes, including their interactions and cumulative impact on CO2 emissions.
3. Microscopic Traffic Simulation Modeling
Leveraging the capabilities of VISSIM, a simulation scenario is constructed featuring a freeway long enough to record congestion avoiding its overflow. This freeway spans slightly more than 6 km, in adherence to the maximum length constraint of 7 km in VISSIM. The lane width is established at 3.75 m. On this basis, the various data detectors required are set-up, including vehicle travel time measurement, vehicle network performance recording, vehicle input data collection, etc.
Certain conditions have been simplified or omitted in this study. One such condition is the omission of slope effects. The reason is that, in real situations, the gradient of accident-congested sections, especially longer congested sections, is dynamic and constantly changing, which is difficult to obtain and consider in simulation and modeling. Future, more complex models can consider incorporating this factor. Furthermore, in the context of various vehicle types, their unique speed–acceleration profiles and engine specifications invariably influence the emission attributes within traffic flow dynamics. Nonetheless, capturing the intricate composition of vehicles poses a challenge when employing discrete or continuous variables. Introducing categorical variables to model these complexities tends to convolute the analysis, diverging from the primary objective of developing a streamlined and user-friendly model. Consequently, we simplified the vehicle composition into two distinct categories: cars and trucks. The parameters defining these vehicle types, such as length and width, are set to default values in VISSIM. Specifically, cars are defined with a default length ranging from 3.75 to 4.76 m and a default width ranging from 1.85 to 2.07 m, while trucks are defined with a default length of 10.22 m and a default width of 2.50 m. The impact of vehicle interior features and age on emissions has not been included in this study. This decision is rooted in the study’s focus on meso-level usage scenarios, particularly highway segments, where acquiring reliable data of vehicle interior features and age proves challenging. Furthermore, consideration of this factor is not conducive to the application of the model.
3.1. Driving Behavior
Driving behavior is set to “freeway” in VISSIM including default vehicle following model type of freeways, default lane change rules of freeways, etc.
Vehicle-following refers to the state in which the following vehicle trails the front vehicle in a single lane, including the special case of free flow with no interactions between the following and the front vehicle [
21]. Within VISSIM, driver’s driving states are classified into four types based on the Wiedemann model: free driving, approaching, following, and braking. The vehicle-following model of VISSIM is a time-based, discrete, and stochastic microscopic model with driver–vehicle unit as the basic entity, which contains two main types of vehicle-following models, namely, Wiedemann 74 and Wiedemann 99. For this study, the Wiedemann 99 model is applied, as it aligns with driving behavior on suburban or freeway roads [
22].
In VISSIM, there are a total of two types of lane change behaviors included, i.e., necessary lane changing (to reach the next connector of a route) and free lane changing (if there is enough space in the adjacent lane and a higher speed is required). Addressing these aspects, VISSIM integrates two lane change models: “slow lane rule” and “free lane selection”. The “slow lane rule” defines the minimum distance to a leading vehicle, allowing overtaking vehicles in other lanes to transition to the slower lane. However, this rule is not applicable to freeways. Consequently, the study adopts the “free lane selection” rule, in which the parameters are default.
The calibration of vehicle speed and acceleration distributions is essential in VISSIM. Cars and trucks exhibit mean velocity distributions of “100 km/h” (ranging from 88 to 130 km/h) and “80 km/h” (ranging from 75 to 110 km/h), respectively. Regarding acceleration and deceleration behavior, it is needed to set the maximum/desired acceleration/deceleration in VISSIM. The maximum acceleration ensures a certain speed on slopes, particularly in situations requiring stronger acceleration. And the maximum deceleration ensures that not even the desired deceleration can fall below it. Only the setting of desired acceleration is considered in this study. The others are set to default functions, whose settings have little effect on the study.
The speed–acceleration functions (desired acceleration functions) of cars and trucks in this study are calibrated using the research findings of Liu et al. [
23], which is based on vehicle data collected from the 2011 Atlanta Household and Activity Travel Survey [
24]. As shown in
Figure 2, the reference distribution by Liu et al. illustrates the speed–acceleration data points for cars and trucks, along with the 97.5th line (representing aggressive acceleration) [
23]. In VISSIM, however, vehicle accelerations are randomly distributed, represented by the two boundary green curves defining the bandwidth and the red curve defining the median. Although the effect of slope is additionally considered in Liu et al.’s research, this study tentatively omits slope considerations. Thus, the red median line is set by referencing the 97.5th line under a 0% slope condition. As there is no explicit reference for the green boundary line, it is empirically adjusted to encompass a majority of the data points in the reference map. This set-up indicates that a significant portion of vehicles will be driven at aggressive accelerations during the simulation, reflecting the future applicable scenario for the model in this study.
3.2. Route Settings
To closely replicate real-world conditions, the study establishes upstream/downstream sections and on/off ramps positioned at both ends of the freeway mainline (
Figure 3). The ratio of mainline flow rate to on/off ramp flow rate is empirically set at 16:1. Because this study focuses on the impact of accidents on freeway mainline traffic and the ramp flow is not the main concern in this study, its discussion is minimized. To mitigate congestion at the off-ramp during high-flow-rate scenarios, the ramp flow is deliberately maintained at a relatively low proportion. This precautionary measure is to avoid congestion spillover into the accident area, which could potentially interfere with congestion detection and compromise the accuracy of the final model.
When driving along a given route, vehicle behaviors (such as lane change for the off-ramp) need to be taken into account. This study mainly considers “the lane change for off-ramp” behavior setting, which mainly involves determining the distance between the point of lane changing location and the point of off-ramp entrance location. Notably, on freeways, drivers often execute lane changes (typically transitioning to the right lane) well before exiting the mainline road. To avert congestion near the off-ramp, where vehicles in the left lane may queue up and wait to change lanes for exiting the mainline roadway, setting an appropriate distance is crucial. Empirically, this distance between lane changing location and off-ramp entrance location is set at 800 m.
Furthermore, the yielding rules in on- and off-ramp conflict zones are configured to mirror real-world scenarios, with a prioritization of yielding to the mainline traffic. Specifically, when a ramp vehicle seeks to enter the mainline, and a conflict arises with a moving vehicle in the rightmost lane of the mainline, the ramp vehicles come to a stop and waits until an adequate gap is available for lane changing. This approach is designed to simulate the conflict in the most realistic manner possible, and the interaction between the on-ramp vehicles and the original mainline vehicles.
3.3. Accident Setting
Certain assumptions are made during the simulation process. Notably, road accidents need to be assumed, as VISSIM lacks a module for directly simulating such events. Consequently, a parking lot is established within the driveway to simulate road accidents. Here, driving a vehicle into the parking lot signifies the start of an accident, while departing from the parking lot represents the conclusion of the accident. When the following vehicle detects a stationary vehicle ahead, it exhibits driving behaviors of slowing down, stopping, or changing lanes. This response resembles the reaction of the following vehicle during an actual accident, thus justifying the utilization of parking simulation for accident.
The accident duration is controlled by configuring the opening hours of parking lot and parking time length distribution. For comprehensive data collection, the parking lot (accident area) is positioned on the road lane near the end of the detection area (
Figure 3). This way, the parking lot can include as much congestion caused by the accident within the detection interval as possible (if the congestion overflows the detected interval, the record of congestion sections need to be discarded). Furthermore, to accommodate accident management activities, the length of parking lot is set to approximately 20–50 m. Additionally, the lateral placement of the parking lot (accident area) varies in different lane scenarios. In this study, the parking lot is positioned in the second lane from left to right in the four-lane scenarios. Similarly, in the three-lane scenarios, it is positioned in the middle lane, and in the two-lane scenarios, it is placed in the right lane.
3.4. Simulation Scenarios
A diverse array of scenarios is designed, encompassing different traffic flow (spanning from congestion to free flow), the accident duration, car–truck ratio, and number of lanes to effectively represent a comprehensive spectrum of real-world cases (
Table 1). Each case is subjected to 3–5 random seeds during simulation to mitigate the impact of randomness. The simulation duration is set at 7200 s, with a warm-up time of 1800 s dedicated to traffic flow stabilization. The accident simulation and data recording start at 1900 s. It should be emphasized that in scenarios with varying numbers of lanes (two-, three-, and four-lane), only the number of lanes and the flow rate setting range need to be modified. The accident location, the length of the detection area, and the length of the freeway remain consistent.
At last, after a total of 5808 simulations, the vehicle second-by-second trajectory data are obtained, which can be used for modeling later.
Based on the queuing situation of the accident lane in various scenarios (
Figure 4), accidents primarily impact traffic flow through three distinct phases: the propagation of congestion after the accident onset, the dissipation of congestion after the accident conclusion, and the subsequent stop-and-go during congestion dissipation. The additional emissions arising from these phases collectively constitute the impact of the accident on traffic flow emissions. In the high-traffic scenario, clear patterns of queue gathering and dissipation waves are discernible (
Figure 4). Conversely, in the low-traffic scenario, such patterns are absent due to the ease with which vehicles can find lane-changing opportunities in adjacent lanes, allowing them to escape the queue, leading to varying queue lengths. However, in high-flow-rate scenarios, vehicles tend to persist in queuing until the accident is resolved, given the challenges associated with the difficulty of lane-changing. Consequently, a gathering wave occurs during the accident, followed by a dissipating wave after the accident concludes. This leads to the development of a gathering wave during the accident and a dissipating wave following the conclusion of accident processing. Moreover, a noticeable stop-and-go phenomenon manifests during queue dissipation in high-traffic scenarios. During the queue dissipation phase, the traffic flow approaches the maximum flow rate that the road can accommodate. Therefore, the traffic system becomes highly sensitive to various factors (e.g., vehicles changing lanes to exit the freeway), thus accentuating the stop-and-go phenomenon. Understanding the queuing dynamics that occur when an accident transpires on a freeway proves invaluable for comprehending the operational patterns of traffic flow during such incidents. This understanding serves as a foundation for developing subsequent statistical models.
5. Statistical Modeling and Results
In the section of traffic simulation, the second-by-second driving states (speed–acceleration information) for all vehicles in the fleet is obtained by the trajectory recording module, thus the speed–acceleration distribution of the fleet can be obtained (
Figure 6). In the figure, each subplot represents the distribution of the simulated second-by-second data volume under different speed accelerations for a given scenario. The x, y, and z axes represent speed, acceleration, and the amount of simulation data at the corresponding speed–acceleration, respectively. Color scale represents the magnitude of z-axis values. In the scenario of high flow rate and long accident duration, the vehicle travel states mainly cluster in the low-speed region, indicating more severe congestion in such scenarios. A substantial number of vehicles experience frequent acceleration and deceleration within congestion or stop-and-go conditions. As the flow rate and accident duration decrease, the proportion of vehicles in the low-speed region gradually diminishes, while the proportion of vehicles in high-speed and low-acceleration region gradually increases. It indicates that in freeway scenarios with low flow rate or brief accident duration, the majority of vehicles experience minimal accident-related impacts and can maintain high cruising speeds. Moreover, the change in vehicle speed–acceleration distribution with varying accident duration is more pronounced in the high-flow-rate scenarios, whereas this change is less notable in low-flow-rate scenarios. This observation offers compelling evidence on the interaction between the effects of these two variables on emissions.
The study integrates the speed–acceleration distribution data with the developed speed–acceleration emission factor library for the estimation of vehicle CO
2 emissions during the simulation process (
Figure 7).
The study successfully derives the comprehensive CO
2 emissions in distinct scenarios by aggregating the CO
2 emissions from vehicles affected by traffic accidents (
Figure 8). In the figure, each subplot represents the distribution of the simulated CO
2 emissions under different speed accelerations for a given scenario. The x, y, and z axes represent speed, acceleration, and the amount of CO
2 emissions at the corresponding speed–acceleration, respectively. Each scenario reveals two prominent emission peaks corresponding to the two vehicle types (cars and trucks), with trucks contributing substantially to emissions despite their lower proportion (ratio = 0.1) in the overall fleet. As the share of trucks increases, the peaks in the image corresponding to truck emissions become more pronounced. Moreover, similar to the (data volume) speed–acceleration distribution, in scenarios of high traffic volume and long accident duration, emissions in low-speed and low- acceleration states, as well as low-speed and high-acceleration states, constitute a significant proportion. This is because a substantial number of vehicles are in low-speed states. Additionally, the emission peaks predominantly occur in the high-speed and low-acceleration region as flow rate and accident duration decrease. Understanding the relationship between vehicle operating conditions (such as speed and acceleration) and emissions during freeway accidents is essential for comprehending the dynamics between freeway traffic flow characteristics and emissions at the mesoscopic level. This understanding serves as both a guiding principle and rational support for developing subsequent statistical models.
The simulation data require scrutiny and preprocessing before modeling. The set length of the detection area in the simulation is 6 km, and the simulation time is limited to 7200 s. As a result, if the congestion queue length exceeds 6 km, or if the congestion persists beyond the end of the simulation, some vehicle congestion is not recorded. To ensure the accuracy of modeling, such data segments need to be removed from the sample. Additionally, despite the requirement for parking (accident occurring), the situation where there is no parking still occurs. This arises from the parking duration being defined by the time length distribution. In other words, despite controlling the randomness of the parking duration with minimal variance, instances may arise where the required parking duration is longer than the opening time of parking lot, resulting in vehicles not parking (the accident does not occur). Consequently, such data segments need to be deleted.
The response variable of the model is the additional CO2 emissions of the scenario, calculated as the difference between the total CO2 emissions of the scenario with an accident and the total CO2 emissions of the scenario without an accident (with an accident duration of 0 min) under identical conditions. This approach highlights the impact of CO2 emissions resulting from accidents. Subsequently, considering the accessibility of the predictors and potential influence on emissions, the predictors are finally selected including the proportion of trucks (representing the car–truck ratio), hourly traffic volume (measured in veh/h), and the accident duration (measured in min).
The modeling process adheres to realistic constraints and incorporates relevant data features. Such as the nonlinear relationship that may exist between the response variable and each of the three predictors (
Figure 9). The presence of this nonlinear feature is reasonable. Using traffic flow as an example, as depicted in
Figure 8, when traffic volume increases (assuming all other conditions remain constant), several outcomes follow, i.e., the length of queues in lanes affected by accidents will grow, congestion will intensify, the frequency of vehicle acceleration and deceleration will rise, and the emission factor per vehicle will increase. Consequently, the additional emissions from traffic exhibit a nonlinear upward trend. However, it is important to note that there are variations in the nonlinear characteristics of each of the three variables. After exhaustive comparisons of various function types, it is observed that the relationship between additional emissions and traffic flow rate exhibits a clear trend towards an exponential function. However, the impact of accident duration or proportion of trucks on additional emissions demonstrates a trend towards power function. Furthermore, the interaction and correlation between each predictor are obvious (
Figure 10). For instance, in the particular scenario (flow rate/proportion of trucks/accident duration = 4800/0.5/30) when accident duration or proportion of trucks decreases, it is evident that the additional emissions for the same flow rate are reduced. However, the overall trend of the relationship between additional emissions and traffic flow rate remains consistent.
Additionally, the constraints considered by the model are as follows:
When the flow rate is 0, the additional CO2 emission must be 0.
When the accident duration is 0, the additional CO2 emission must be 0.
When the truck proportion is 0, the additional CO2 emission must be greater than 0.
Based on the data features and constraints, as well as the attempts of multiple functional forms, the final selected model form is as follows. The variable “Flow Rate” (veh/h) is transformed as “exp(b*flow) “, and the variables “accident duration” (min) and “the proportion of trucks” are transformed as “Accident-Duration^b” and “Truck-Proportion^b” (“b” is parameter required to fit). Estimates of each parameter are obtained using the nonlinear regression module of R by RStudio (version: RStudio 2023.06.0 + 421) (
Table 3). The model formula is as provided in Equations (1)–(3):
In Equations (1)–(3) and
Table 3,
is the additional CO
2 emissions due to accidental congestion (ton),
is traffic flow rate (veh/h),
is the proportion of trucks,
is accident duration (min), and
are the model parameters to be fitted.
In the process of parameter fitting, we mainly utilized the nonlinear least square function in R and adopted the Gauss–Newton algorithm for solving. The use of this function requires providing the initial values for each parameter, which are obtained empirically through repeated attempts.
The goodness-of-fit indicators for the model mainly include adjusted R
2, RMSE, and a comparison between predicted and actual (simulated) values. The models for each scenario exhibit compelling goodness of fit with notably high adjusted R
2 (ranging from 0.960 to 0.977) and low RMSE values (ranging from 0.160 to 0.432). Meanwhile, the scattered points are evenly and closely distributed around the y = x line. These observations exhibit the strong alignment of the model result with the simulation data (
Figure 11).
For validating the model, test data are obtained by resetting the VISSIM scenarios and conducting simulations. Specifically, the two-, three-, and four-lane scenarios are simulated, respectively, encompassing various conditions of high/low traffic flow rate, high/low proportion of trucks, and high/low accident duration. Therefore, for each model, there are 240 different simulation results to test (
Table 4). To ensure the integrity and credibility of data validation, this study intentionally select some cases that are not included in the previous sample data as much as possible, and even incorporated some extreme cases (such as the proportion of trucks is 0) to test the robustness of the model.
Regarding the model validation metrics, RMSE and comparison between predicted and actual (simulated) values are considered. As shown in the figure, the model validation results perform very well (
Figure 12), which proves the robustness and accuracy of these models.
From this statistical model, it is evident that the impact of accident duration, truck proportion, and traffic flow rate on the additional emissions caused by accidents is nonlinear (Equations (1)–(3)). This nonlinearity indicates that the marginal effect of these three variables on emissions increases with their own increase. Moreover, there is also a clear interaction between variables in the statistical model. The effects of each variable on emissions fluctuates with variations in the other two variables., with a mutually reinforcing and positive relationship. For instance, at high traffic demand or long accident duration, optimizing accident management efficiency (reducing management time) results in more substantial emission reductions compared to scenarios with low traffic demand or short accident duration.
A comparison of the three models reveals that the two-lane model exhibits superior fit compared to the other two models (
Figure 11 and
Figure 12). This superiority can be attributed to the fact that the two-lane model incorporates fewer stochastic factors, such as fewer free lane-changing behaviors, compared to the other two scenarios. Regardless of the number of lanes in the scenario, CO
2 emissions demonstrate increasingly sensitivity to the accident duration as traffic flow rate and the proportion of trucks rise. In addition, CO
2 emissions are more sensitive to traffic flow rate in comparison to accident duration and the proportion of trucks. This implies that implementing measures to evacuate vehicles from the accident area (to reduce traffic flow rate in the accident area) may prove more effective in mitigating emissions than other emission reduction measures.
6. Conclusions
This study quantifies the nonlinear relationship and positive interaction between additional CO2 emissions due to accidents and three key predictors (accident duration, traffic flow rate, and the proportion of trucks). The findings demonstrate that optimizing accident management efficiency results in more substantial emission reductions in scenarios with high traffic demand or long accident duration. Moreover, the study suggests that implementing measures to evacuate vehicles from the accident area (to reduce traffic flow rate in the accident region) may be more effective than alternative emission reduction measures. The modeling approach employed in this paper can serve as a viable and valuable reference for future studies seeking to model real-world data.
Considering the insufficient samples of real data and the difficulty of obtaining them on a second-by-second basis, we use simulation data for modeling. Our main purpose is to propose a valuable law, which can be used in future applications to correct the parameters of the model based on the actual data in order to avoid the problem of distortion of the simulation data.
This study contributes to the existing body of research by directly establishing a statistical relationship between the additional CO2 emissions resulting from highway accidents and the methods of accident management. It enriches the current methodologies for predicting accident-related emissions and addresses issues such as poor applicability observed in similar studies on emission prediction. Furthermore, it synthesizes statistical patterns to offer guidance for further exploration and analysis in this field.
The model proposed in this study holds promising potential for providing valuable guidance with formulating emission reduction strategies and serving as a reference for policy-making decisions. By quantitatively assessing the impact of accident on CO2 emissions and the impact of accident management efficiency, the model can help freeway O&M companies and relevant stakeholders by adopting more targeted means to mitigate the influence of accidents on CO2 emissions. For instance, if improving the efficiency of accident management requires the employment of engineering equipment that emits more CO2, we should consider the impact of efficiency-improving strategies from a full life cycle perspective. In other words, if the reduction in emissions from the improved efficiency is significantly less than the increase in emissions from the equipment, it will be unadvisable to implement these strategies to improve the efficiency of accident management.
There is still a lot of work to be performed ahead. Many assumptions and simplifications made during the current study present opportunities for further refinement. For instance, the enrichment of simulated vehicle types and the incorporation of emission factors for vehicles with different emission standards are areas that warrant attention in future investigations. The model still has potential for improvement. The model validation of this study is currently conducted through VISSIM simulations, but future improvements may involve refining the model based on real-world data to enhance its applicability in real scenarios.
Moreover, there is scope for enhancing the research design in future research. While this study is conducted at the micro level, a more macroscopic simulation is essential to evaluate the impact of the accident duration on the traffic flow of road network (particularly for urban traffic accidents). In addition, this study can be used to evaluate measures of improving the efficiency of accident management, but there are numerous other measures for accident abatement (speed management, traffic flow smoothing, etc.). Future research can enrich and expand the model to encompass a broader range of measure assessments.