1. Introduction
Optical fiber has many advantages compared with electric cables, such as high bandwidth, low loss, a compact size, immunity to electromagnetic interference, and large capacity [
1,
2,
3]. To satisfy the unprecedented demand for an ever-higher fiber network capacity as data network traffic grows, this multiplexing technology is used to enhance communication link capacity. The optical switch is an indispensable component in such a multiplexing system, as it enables the routing of optical data signals without a conversion to electrical signals, and it is independent of data rate and data protocol [
4]. A very important function of optical switches is the provisioning of light paths. Optical switches can be categorized into three types according to the switching principles, namely optomechanical switches, interferometric switches, and digital optical switches [
5]. Optomechanical switches are widely used in applications with relatively low switching speed. In optomechanical switches, the switching action is performed by some mechanical means, such as prisms, mirrors, and directional couplers, etc. The microelectromechanical systems system (MEMS) optical switch is an important member of optomechanical switches. Compared to other optomechanical switches, a MEMS optical switch has advantages of a compact size, fast switch speed, low insertion loss, low crosstalk, and polarization sensitivity, and it is considered the mainstream in large-capacity switched optical networks [
4,
6]. In MEMS switches, the light beam is redirected to a desired port by the microactuator.
MEMS devices have both electrical and mechanical components, and they contain at least one movable structure for some mechanical action [
7]. Movability is perhaps the most important character of a MEMS, and so the actuator is one of the most important parts of the MEMS. The structure design and driving principles are the two key points for actuators. So far, various driving modes have been studied, such as thermal expansion [
8,
9], electrostatic force [
10,
11,
12], piezoelectric effect [
13,
14], shape memory alloys [
15,
16], and electromagnetic force driving [
17,
18,
19], and a hybrid of thermal and electromagnetic methods [
20]. Additionally, metamaterials were designed as the driving units in the MEMS actuators in recent years [
21,
22,
23]. The motion mechanism is mostly based on electrostatic and electromagnetic driving. Actuators based on electrostatic force can be batch-manufactured like integrated circuits, and thus they are one of the most popular drivers. However, the driving force is small and the driving voltage is too high to be compatible with other circuits. Piezoelectric ceramic is widely used in a MEMS for precision driving, but it cannot achieve large displacement motion. Electromagnetic driving has the merits of a large driving force, higher efficiency and longer operation lifetime, and large output displacement.
In this paper, a novel swing-type MEMS actuator is proposed for optical switches. This actuator has an axial magnetic flux structure with multiple windings and magnetic poles. It has the advantages of a large output torque, fast response, a compact size, and good position repeatability.
2. Design of Actuator
2.1. Structure Design
In the MEMS optical switch, the actuator is the key element to control the mirrors to move in and out of the light path. To increase the output torque and the response speed of the actuator, an axial magnetic flux structure with multiple windings and magnetic poles is proposed, as shown in
Figure 1. The actuator consists of four parts: the stators composed of ferrite substrate and Cu windings; the swing disc made up of a SmCo permanent magnet and silica steel plate; the rotating shaft parts, including a counterweight, rotating shaft, and ruby bearings; and a protective cover and the positioning permanent magnet. The actuator is a three-layer structure, where the swing disc is sandwiched between the two stators. This laminated structure can improve the output torque of the actuator. The magnetic attraction of the upper and lower stators to the disc can be counteracted with each other, which can reduce the friction of the swing disc. The ruby bearings are used in the actuator to alleviate the shaft abrasion, which will decrease the driving voltage and power consumption, and thus prolong the service life. The stator winding can be fabricated by the microprocessing technique.
2.2. Working Principle
Figure 2 shows the diagram of the stator and swing disc structure, as well as the interaction between the stator and swing disc. There are six windings on the stator substrate, and a piece of FeNi alloy is embedded into each winding as the magnetic core, as shown in
Figure 2a. This magnetic core can reduce the magnetoresistance and increase the output torque. The structure of the swing disc is illustrated in
Figure 2b. Six magnetic poles are written in the SmCo permanent magnet of the swing disc. There is a silica steel pushrod at one side of the disc to output displacement. A mirror is mounted on the end of the steel pushrod to control the connection and disconnection of the light path. There is an angle of 30 degrees between the magnetic pole boundary and the winding edge. The magnetizing direction of the permanent material in the swing disc is parallel to the rotating axis. When the current flows through the winding, an ampere force along the circumference of the stator is generated. As shown in
Figure 2c, when the current flows through the winding
Q in the anticlockwise direction (A → B → C → D → A), the radial wires (AB and CD) will be acted on by the anticlockwise force along the circumference of the stator. Because the windings are fixed on the stator substrate, the swing disc will be acted on by the counterforce, which induces the clockwise rotation of the swing disc. When all the windings are energized, the driving force acting on the swing disc is the resultant force of all windings.
When the direction of the electric current in the windings is reversed, the swing disc will be acted on by the inverted force, and the swing disc turns back. Because of the position limitation of the pushrod on the side of the disc and the design of the windings and magnetic poles, the swing disc can only swing in a definite angle range. Two permanent magnets are placed on both sides of the pushrod to maintain the position when the electrical source is disconnected. To reduce the vibration induced by the pushrod, a counterweight is fixed on the rotating axle to balance the load of swing disc.
2.3. Analysis of Magnetic Circuit
The calculation of the magnetic circuit of the actuator is a complex nonlinear problem. There are various methods of air-gap field calculation, including finite element analysis, equivalent magnetic charge, and Fourier transform. Here, we adopted the Fourier transform to solve the magnetic field in the air gap. The calculation model of the magnetic field for the swing actuator is described in
Figure 3 under the following assumptions:
The magnetic shielding on the upper and lower stators of the swing disc are soft magnetic materials with high permeability, and so its permeability can be approximately considered infinite.
The distribution of the shielding layer of the swing disc is an infinite space because the air gap between the swing disc and the stator is far smaller than the diameter of the disc.
The magnetization vector of the swing disc is stable and perpendicular to the surface of the disc, and the magnetization direction of the adjacent magnetic poles is opposite.
According to the calculation model, the magnetic field in the air gap is the sum of the field intensity produced by the disk and its mirror image. The magnetic field intensity on the plane Z can be calculated by Equation (1).
where
is the field intensity of swing disc in the free space,
t is the thickness of the swing disc, and
g is the distance between the disc surface and the soft magnet.
The magnetic flux density of the disc can be acquired by Equation (2).
For the magnetic flux density in the air gap, the magnetization vector
is equal to 0. The relation between the magnetic flux density and the dimension of the air gap is illustrated in
Figure 4.
The windings of the actuator can be regarded as an integration of many wire units. When the current
i flows through the wire with a length of Δ
l, the electromagnetic force can be calculated by Equation (3). The sum of the torque acted on the swing disc can be obtained from Equation (4):
where
is the sum of the torque,
θ is the angle between the current and the direction of magnetic flux, and
r is the radius of rotation.
From Equation (4), it can be observed that the output torque
T is directly proportional to the magnetic flux density
B, the electric current
i, the wire length
l, and the rotation radius
r. In consideration of the compact size of actuator, the optimal measure to enhance the output torque is to increase the magnetic flux density. From
Figure 4, it can be seen that the magnetic flux density in the air gap attenuates with the increase of the air gap. The air gap cannot be too small; otherwise it could affect the assembly of actuator. NiFe alloy with high permeability was used to increase the magnetic flux density in the air gap. The NiFe alloy magnet is embedded into the windings as a magnetic core as shown in
Figure 5.
3. Fabrication of Actuator
The fabrication of an actuator is a manufacturing process that integrates bulk micromachining, precision manufacturing, and assembly. The fabrication of the stator and the magnetization of swing disc are the key procedures of the fabrication.
3.1. Stator Fabrication
3.1.1. Material Preparation
The substrate of the stators is the supporting body of the wings, and the magnetic field lines can form a closed loop. The material of the substrate must satisfy three requirements: machinability, good magnetic conductivity, and nonconductivity. Here, the ferrite was chosen as the material of the substrate. The NiFe alloy was selected as the magnetic core in the windings due to its high permeability and good conductivity. The thickness of the single layer of NiFe alloy is about 20 μm. Mask electroplating was used to form the NiFe alloy film. The electroplating solution is NiSO4+NiCl2+FeSO4, and its pH is in the range of 5–6. Al2O3 was used as the insulating material of the interface layer of windings because of its good insulation, temperature stability, and durability, which can effectively solve the aging problem of the insulation material and increase the lifetime of the actuator.
3.1.2. Manufacturing Process
Generally, micromachining technology is mainly carried out on silicon materials. A special processing technology was developed for the ferrite, which includes masking, photoetching, sputtering, and dry etching, as shown in
Figure 6. The procedures of fabrication are concluded as follows:
3.2. Swing Disc Fabrication
The swing disc is one of the key components of the actuator, and it determines the magnitude of output toque. It is important to select the optimal material for the permanent magnet in the disc. Taking the performance of manufacturing and pole writing into consideration, two SmCo permanent magnets were glued onto the upper and lower surfaces of the swing disc made up of silicon steel. The permanent magnetic material has a property of magnetic remanence Br (0.8–0.9 T), a minimum intrinsic coercivity Hc (1592 kA/m), and a magnetic energy product (BH)max (119–143 kJ/m3). The swing disc was manufactured by electrodischarge machining.
The magnetic poles writing is also a key process for the actuator. The uniformity and magnetic saturation of the poles are decisive to the performance of the swing disc. A magnetizing device with a particular size was designed and fabricated to magnetize the permanent magnet of the swing disc. The magnetic photograph of the magnetic poles is shown in
Figure 7a. The picture shows that the magnetic poles are uniform in size and distribution. The magnetic remanence of the swing disc was measured. The results show that the magnetic remanence in the swing disc is the same as that of the permanent magnet block, which indicates that the swing disc is in the magnetic saturation state. The actuator porotype with a compact size of 5.1 × 5.1 × 5.3 mm
3 is fabricated as shown in
Figure 7b.
4. Performance Testing
The output torque, swinging angle, and switching time were the key parameters for the optical switches. A loading test platform was established to measure the output torque and swinging angle, as shown in
Figure 8. A weight was connected to the pushrod by a string, and a pulley was used to support and guide the string. The proposed actuator was controlled by a signal generator that drags up the weight. Simultaneously, a distance sensor was adopted to detect the displacement of weight. The maximum output torque can be obtained by the product of the maximum weight and the push rod length. The length of the pushrod is 8 mm, and the maximum weight is 0.5 g, which indicates that the maximum output torque is 40 μNm.
The calculation model of the swinging angle is shown in
Figure 9. The swing angle can be calculated by Equation (5).
where
α is the swing angle,
d is displacement of weight detected by the sensor, and
R is the swing radius of pushrod.
Because the angle β is far too small and sinβ is approximately 1, the swing angle is equal to arcsin(d/R). The testing results show that and the actuator has a maximum swing angle of 22° and a swing displacement of 5.4 mm.
Previously, the mechanical parameters of the proposed actuator were tested. The key functional parameter (switching time) was tested, and the experimental setup is shown in
Figure 10a. The light from the laser was divided into two paths by the reflected mirror in the actuator. The two beams of light were coupled into one by a fiber coupler, and then the coupled light was detected using a photodetector, which was composed of a photodiode and amplifier. The output of the photodetector was illustrated on the oscilloscope (MSO7032A, Agilent Technologies, Santa Clara, CA, USA). When the pushrod of the actuator is in the position shown in
Figure 9, the light is reflected by the mirror and travels through path B. The light travels through path A when the mirror swings away from this position. With the reciprocating swing of the actuator, the amplitude of output signal shows a downward and upward trend. The switching time can be obtained from the time interval between the first decay to 10% of the stable amplitude and the next rise to 90% of the stable amplitude, as shown in
Figure 10b. The testing result is illustrated in
Figure 11. The minimum switching time is 5 ms, which is comparable to the commercial products (≤30 ms [
24], ≤15 ms [
25], 0.5–1 ms [
26]).
5. Conclusions
An electromagnetic MEMS swing actuator was developed in this paper. The actuator has a sandwich structure, including two stators, a swing disc, a rotating shaft, and covers.
The working principle and the magnetic circuit of the proposed actuator were analyzed. The results show that the actuator’s output torque is decisive to the air gap’s magnetic flux density between the stators and swing disc. An optimal measure was taken to increase the output torque using NiFe alloy magnetic cores that were embedded into each winding center. Six copper windings and NiFe magnetic cores were electroplated on the ferrite substrates. The corresponding six magnetic poles were distributed onto the SmCo permanent magnet of the swing disc.
The actuator prototype was fabricated, and experiment platforms were established to test the performance of the actuator. The design and manufacturing process enabled the proposed actuator to have a large output torque of 40 μNm, a fast response of 5 ms, and a large swing angle of 22°. This actuator can be used for the optical fiber switches and the automatic switching of the light path in other applications.
Author Contributions
Conceptualization and methodology, S.J.; fabrication and investigation S.J. and J.P.; writing—original draft preparation, J.P.; writing—review and editing, J.P. and S.Z.; visualization, S.Z. and J.B.; resources and funding acquisition, S.X. and B.Z. All authors have read and agreed to the published version of the manuscript.
Funding
This research was funded by the Natural Science Foundation of Jiangxi Province, grant number 20202BAB204019, and the National Natural Science Foundation of China, grant number 52075429 and 92060110.
Conflicts of Interest
The authors declare no conflict of interest.
References
- Barrias, A.; Casas, J.R.; Villalba, S. A Review of Distributed Optical Fiber Sensors for Civil Engineering Applications. Sensors 2016, 16, 748. [Google Scholar] [CrossRef] [Green Version]
- Liang, L.; Li, M.; Liu, N.; Sun, H.; Rong, Q.; Hu, M. A High-Sensitivity Optical Fiber Relative Humidity Sensor Based on Microsphere WGM Resonator. Opt. Fiber. Technol. 2018, 45, 415–418. [Google Scholar] [CrossRef]
- Addanki, S.; Amiri, I.S.; Yupapin, P. Review of Optical Fibers-introduction and Applications in Fiber Lasers. Results Phys. 2018, 10, 743–750. [Google Scholar] [CrossRef]
- Wong, L.L.P.; Yeow, J.T.W.; Goldenberg, A.A. MEMS-based optical switches. In Optical Switches; Li, B., Chua, S.J., Eds.; Woodhead Publishing: Sawston, Cambridge, UK, 2010; pp. 136–157. [Google Scholar]
- Papadimitriou, G.I.; Papazoglou, C.; Pomportsis, A.S. Optical Switching: Switch Fabrics, Techniques, and Architectures. J. Lightwave. Technol. 2003, 21, 384–405. [Google Scholar] [CrossRef] [Green Version]
- Chollet, F. Devices Based on Co-Integrated MEMS Actuators and Optical Waveguide: A Review. Micromachines 2016, 7, 18. [Google Scholar] [CrossRef]
- Eddy, D.S.; Sparks, D.R. Application of MEMS Technology in Automotive Sensors and Actuators. Proc. IEEE 1998, 86, 1747–1755. [Google Scholar] [CrossRef] [Green Version]
- Hirano, T.; Long-Sheng, F.; Gao, J.Q.; Lee, W.Y. MEMS Milliactuator for Hard-Disk-Drive Tracking Servo. J. Microelectromech. Syst. 1998, 7, 149–155. [Google Scholar] [CrossRef]
- Sinclair, M.J. A high force low area MEMS thermal actuator. In Proceedings of the 7th Intersociety Conference on Thermal and Thermomechanical Phenomena in Electronic Systems, Las Vegas, NA, USA, 23–26 May 2000; pp. 127–132. [Google Scholar]
- Shi-Sheng, L.; Long-Sun, H.; Chang-Jin, K.; Wu, M.C. Free-Space Fiber-Optic Switches Based on Mems Vertical Torsion Mirrors. J. Lightwave Technol. 1999, 17, 7–13. [Google Scholar] [CrossRef]
- Liu, Y.; Xu, J.; Zhong, S.; Wu, Y. Large Size Mems Scanning Mirror with Vertical Comb Drive for Tunable Optical Filter. Opt. Laser. Eng. 2013, 51, 54–60. [Google Scholar] [CrossRef]
- Wang, F.; Lu, C.; Liu, Z.S.; Li, J.; Liu, A.Q.; Zhang, X.M. Finite Element Simulation and Theoretical Analysis of Fiber-Optical Switches. Sens. Actuators A Phys. 2002, 96, 167–178. [Google Scholar] [CrossRef]
- Tadigadapa, S.; Mateti, K. Piezoelectric MEMS-sensors: State-of-the-Art and Perspectives. Meas. Sci. Technol. 2009, 20, 092001. [Google Scholar] [CrossRef]
- Koh, K.H.; Kobayashi, T.; Lee, C. A 2-D MEMS scanning mirror based on dynamic mixed mode excitation of a piezoelectric PZT thin film S-shaped actuator. Opt. Express 2011, 19, 13812–13824. [Google Scholar] [CrossRef] [PubMed]
- Makino, E.; Mitsuya, T.; Shibata, T. Fabrication of TiNi Shape Memory Micropump. Sens. Actuators A Phys. 2001, 88, 256–262. [Google Scholar] [CrossRef]
- Pan, Q.; Cho, C. The Investigation of a Shape Memory Alloy Micro-Damper for MEMS Applications. Sensors 2007, 7, 1887–1900. [Google Scholar] [CrossRef] [PubMed] [Green Version]
- Getpreecharsawas, J.; Puchades, I.; Hournbuckle, B.; Fuller, L.; Pearson, R.; Lyshevski, S. An Electromagnetic MEMS Actuator for Micropumps. In Proceedings of the 2nd International Conference on Perspective Technologies and Methods in MEMS Design, Livi, Ukraine, 24–27 May 2006; pp. 11–14. [Google Scholar]
- Chang, H.-T.; Lee, C.-Y.; Wen, C.-Y. Design and Modeling of Electromagnetic Actuator in Mems-Based Valveless Impedance Pump. Microsyst. Technol. 2007, 13, 1615–1622. [Google Scholar] [CrossRef]
- Lv, X.; Wei, W.; Mao, X.; Chen, Y.; Yang, J.; Yang, F. A Novel MEMS Electromagnetic Actuator with Large Displacement. Sens. Actuators A Phys. 2015, 221, 22–28. [Google Scholar] [CrossRef]
- Koh, K.H.; Lee, C. A low power 2-D raster scanning MEMS mirror driven by hybrid electrothermal and electromagnetic actuation mechanisms. In Proceedings of the 2012 International Conference on Optical MEMS and Nanophotonics, Banff, AB, Canada, 6–9 August 2012; Volume 2012, pp. 236–237. [Google Scholar]
- Pitchappa, P.; Ho, C.P.; Singh, N.; Lee, C. Electrostatically switchable MEMS terahertz metamaterial with polarization-insensitive characteristics. In Proceedings of the 2015 IEEE International Conference on Electron Devices and Solid-State Circuits (EDSSC), Singapore, 1–4 June 2015; Volume 2015, pp. 25–28. [Google Scholar]
- Pitchappa, P.; Ho, C.P.; Lin, Y.; Lee, C. Enhanced electro-optic switching characteristics using mems based terahertz metamaterial. In Proceedings of the 2014 International Conference on Optical MEMS and Nanophotonics, Glasgow, UK, 17–21 August 2014; Volume 2014, pp. 37–38. [Google Scholar]
- Pitchappa, P.; Ho, C.P.; Lee, C. Polarization-insensitive electro-optic switching in terahertz MEMS metamaterial. In Proceedings of the 2015 IEEE MTT-S International Microwave Workshop Series on Advanced Materials and Processes for RF and THz Applications (IMWS-AMP), Suzhou, China, 1–3 July 2015; Volume 2015, pp. 1–3. [Google Scholar]
- COFIBER. Available online: http://www.cofiber.net/product/showproduct.php?id=263 (accessed on 5 February 2021).
- HC OPTICAL. Available online: http://www.glhcoptical.com/index.php?aid=520 (accessed on 5 February 2021).
- Sercalo Microtechnology. Available online: https://www.sercalo.com/images/products-pdf/sw-smf/sw1x2-SMF.pdf (accessed on 5 February 2021).
| Publisher’s Note: MDPI stays neutral with regard to jurisdictional claims in published maps and institutional affiliations. |
© 2021 by the authors. Licensee MDPI, Basel, Switzerland. This article is an open access article distributed under the terms and conditions of the Creative Commons Attribution (CC BY) license (http://creativecommons.org/licenses/by/4.0/).