1. Introduction
Intensive and quick urbanisation is not only observed in developing countries, but also in those of the former communistic block, such as Poland. Unfortunately, the intensive development of cities is accompanied by a number of negative phenomena, among them primarily rapidly growing amounts of municipal solid waste (MSW) and sewage sludge (SS) [
1,
2]. Currently due to the rapid increase in the mass of municipal solid waste, it must be perceived as a multidimensional global problem, and proper waste management needs to be developed to attain such goals as the prevention of waste generation and reduction of its volume, increasing resource efficiency, diminishing the quantity of waste intended for landfills, as well as encouraging its reuse and raw material recovery. The principles of circular economy and the assumptions of the zero waste program [
3] are helpful, because recyclable materials are reintroduced into the economy as new raw materials, thus increasing the security of their supply. Taking the above into consideration, in addition to plastic, paper, glass, and metals, biowaste is increasingly being sorted in municipalities as well. Thanks to adapting such a system of municipal waste collection in recent years, the mass of biowastes has significantly increased in Poland, amounting in 2018 to 28.4% of total mass [
4]. It presents a new challenge, because according to the Landfill Directive [
5], the EU member states are obliged to reduce the amount of biodegradable municipal waste going to landfills and simultaneously alternative strategies should be developed, such as composting (including fermentation), incineration and pre-treatment, e.g., mechanical–biological treatment (including physical stabilisation). As indicated by data given on the Bio-waste in Europe website [
6], across the European Union, somewhere between 118 and 138 million tonnes of biowaste are generated annually, of which currently about 25% are composted or digested yearly, with composting predominating over anaerobic digestion. In Poland, composting also prevails and is dedicated to organic wastes. Due to the fact that the group of organic waste is large and diversified, two separate subgroups of biowaste and biodegradable wastes can be distinguished within it. Biowastes are obligatory collected selectively by residents and include garden and park wastes, food, and kitchen wastes from households and restaurants. In contrast, biodegradable wastes include both wastes collected selectively by residents (paper, cardboard) and those resulting from agricultural and forestry activities (forestry and agricultural residue) or municipal wastewater treatment (sewage sludge).
Urbanisation and agglomeration processes, enhancing wastewater infrastructure development as well as the introduction of more advanced methods of municipal wastewaters purification, are factors playing a major function in the increase of sewage sludge mass. This biodegradable, noxious waste should also be considered as an additional civilisation-related problem, because landfills are the least desirable manner of SS utilisation and for example in Poland according to the Polish legal regulations [
7], starting from 2016 such wastes may not be deposited at landfills. In order to implement sewage sludge application for environmental purposes, it is a very important strategy to comply with the above-mentioned Landfill Directive [
5] and the principles of the circular economy. In Poland in 2018, of the total SS mass generated, almost 30% were used for applications in the natural environment, e.g., agriculture, land reclamation, or the cultivation of plants intended for composting [
4].
Regardless of organic waste type, the best and most sustainable method of their utilisation seems to be the composting process, because it allows reusing their potential by incorporating nutrients and organic matter into circulation while maintaining the waste–soil–plant production continuum. The composting process has been presented as an environmentally friendly alternative applied to manage and recycle organic waste to obtain products used as amendments in agriculture [
8,
9]. Thomas et al. [
10] listed positive aspects related to the utilisation of recycling organic wastes as crop fertilisers. Among other things, the cited authors pointed to the reduction of greenhouse gas emissions or enhanced carbon sequestration. Most studies [
2,
11,
12,
13] clearly demonstrate that soil amendment with compost affects various soil properties, including physical, chemical, physicochemical, and biological, especially enhancing TOC, Ntot amounts, and the contents of available macronutrients (N mineral, P, K, S, Mg). Despite many positive aspects connected with compost application, some disadvantages should also be underlined. Obviously, its slow mineralisation and the resulting sluggish progress of nutrient release diminish the agricultural value of composts. Especially the low level of nitrogen is of importance in this respect and thus to meet nitrogen requirements of crops, composts must be applied at higher rates [
13]. However, bigger doses of composts may be accompanied by the introduction of larger amounts of undesirable metals such as Cd, Cr, and Pb, which are also present in compost composition [
2]. In view of the above, it is essential to evaluate the quality of composts prior to soil application, which is required because of the vast variability in the chemical composition of organic wastes used for compost production. The above-mentioned diversity results from the origin of various raw materials and the technologies applied to convert wastes into organic fertiliser [
14]. In Poland, the composting process may be carried out in both technologies: large-scale commercial (composting facilities) and small-scale household facilities (home composters). Commercially produced composts are always certified products used for agriculture and horticulture, the reclamation of industrial areas, as well as the maintenance of municipal green areas. Composts from home composters do not undergo any evaluation, since they are only used in home gardens as fertilisers in the small-scale growing of vegetables and ornamental plants.
Regardless of the chemical composition and used technology, only the application of stable and mature compost can improve soil fertility by increasing soil organic matter, suppressing soil-borne plant pathogens and enhancing plant growth. However, immature compost may have adverse effects on plant growth and the environment because of the presence of phytotoxic compounds, low molecular weight organic acids, ethylene oxide, and pathogens [
15]. Maturity refers to the degree of decomposition of phytotoxic organic substances produced during the active composting phase and to the absence of pathogens. Stability is related to the rate of microbial activity in compost, and it is evaluated by different respirometric measurements and/or by studying transformations in chemical properties [
15,
16]. Various and numerous methods have been used to determine the maturity and stability of composts. Jakubus [
17] reviewed these methods and distinguished four groups concerning physical parameters (temperature, colour, moisture, content, and aeration); chemical parameters (C:N ratio, NH
4:NO
3 ratio, cation exchange capacity—CEC, pH, electrical conductivity—EC, and humification indexes); microbiological parameters (respiration analysis, ATP content, and enzyme activities) and biological parameters (germination index and plant growth bioassay). In view of the above, there are different methods that in routine practice are difficult to apply simultaneously. Nowadays, methods that will be fast, simple, cheap, and at the same time provide real and repeatable results are sought for and required. Considering the compost soil application and its impact on this environment, compost evaluation should be based on an assessment of nutrient abundance. Moreover, information on the phytotoxic effect of composts as well as the intensity and direction of transformation of organic matter introduced into the soil is also important [
11]. Thus, the main aim of this study was to valorise 10 various composts using selected chemical and biological parameters in terms of their fertilising quality and potential usability for application in horticulture, agriculture, or land reclamation. The analysed composts were prepared from commonly used wastes (garden and park waste) as well as those less popular (sewage sludge and spent mushroom substrate). The performed qualitative evaluation made it possible to differentiate composts among themselves, regardless of the raw materials used for composting. In addition, an attempt was made to assess the usefulness of the indicators used in the practical assessment of compost maturity and stability.
3. Results
As shown by the obtained data, the tested composts differed in terms of their contents of macro- and micronutrients, the quantity and quality of humus compounds, as well as the impact on the efficiency of seed germination and plant root growth. Among the 10 analysed composts, significant similarities and a lack of statistical differences can be observed between the analysed nutrient amounts. This is particularly evident in the case of composts 1 and 3, which had very similar values of C:N and Q
4/6 (
Table 2). Additionally, these composts did not differ in the contents of OM, C
HS, the amounts of Mg, S, P, Fe, Zn, and Cu (
Figure 1 and
Figure 2,
Table 3 and
Table 4). Also the values of SGI, RGI, and GI were comparable for mentioned composts (
Figure 3 and
Figure 4). In addition, composts 7 and 8 were characterised by contents of most of the analysed nutrients as well as TOC, OM, and C
FA, which were not statistically different. Composts 2 and 4 did not differ in terms of OM, N, S, P, Mg, Ca, Fe, Zn, and Cr contents (
Table 3 and
Table 4,
Figure 1). These composts also presented similar values of Q
4/6, SGI, RGI, and GI (
Table 2,
Figure 3 and
Figure 4). Despite the fact that composts 5 and 6 were prepared in the same technology using sewage sludge (although in different percentage shares, see:
Table 1), they showed no significant differences only in the contents of TOC, OM, C
HA, C
HS, and N (
Figure 1 and
Figure 2,
Table 3). Additionally, HI (18.8–20.1%), HR (27.5–29.0%) and DP (2.2–2.4) values were comparable for these composts (
Table 2). Similar effects on seed germination and root growth were found for composts 9 and 10 (
Figure 4).
According to the Polish standards specified in the Regulation of the Minister of Agriculture and Rural Development [
25], organic fertilisers have to contain a minimum of 30% organic matter, while contents of nitrogen (N), phosphorus (P
2O
5), and potassium (K
2O) have to have a minimum of 0.3%, 0.2%, and 0.2%, respectively. Referring to the above values, only composts 7 and 8 did not meet the criterion for the minimum amount of organic matter (
Figure 1). The amounts of N ranged from 0.3% (C7) to 2.5% (C5), thus meeting the required minimum. In addition, all the composts met the threshold for potassium contents, because the K level converted into K
2O ranged from 0.2% (C8) to 1.2% (C5). Phosphorus expressed as P
2O
5 amounts ranged from 0.3% (C7) to 1% (C5 and C6), thus meeting the threshold specified in the legal act. The requirements given in the Regulation of the Minister of Agriculture and Rural Development [
25] describing the limits of heavy metals in organic fertilisers are more lenient compared with those contained in the EC 889/2008 Commission Regulation [
26], because Polish law specifies that the levels of the following heavy metals in mg∙kg
−1 of dry matter of compost cannot exceed the following thresholds: Cr = 100; Cd = 5; Ni = 60; Pb = 140; and Hg = 2. However, the EU law in composted or fermented household wastes allows only the presence of Cr = 70; Ni = 25; Pb = 45; Cd = 70; Cu = 70; Zn = 200 and Hg = 0.4 mg∙kg
−1. Comparing the above-mentioned threshold values with those obtained for the analysed composts, it should be stated that both Polish and European standards were met for composts prepared by the AANC technology (C7 and C8). The other composts exceeded the given limit values. For Cu, it was found for C5 (153.7 mg∙kg
−1) and C6 (118.4 mg∙kg
−1). The amounts of Zn did not meet the criteria and were higher in the case of C5 (497.2 mg∙kg
−1), C6 (372.4 mg∙kg
−1), C9 (322.4 mg∙kg
−1) and C10 (272.7 mg∙kg
−1). Compost 5 with 33 mg∙kg
−1 exceeded the limit for Ni. As it results from the above, compost 5 was characterised not only by the highest contents of macronutrients (TOC, N, P, K), but also microelements (Zn, Cu, Ni, Fe) (
Table 3 and
Table 4) and heavy metals (Cr, Pb) (
Figure 5). The greatest contents of HS and C
HA (
Figure 2) as well as one of the highest values of HI (18.8%) and HR (27.5%), were also obtained for this compost (
Table 2).
It should be emphasised that C5, similarly to C6, very strongly inhibited seed germination (SGI = 30.4–38.6%) and plant root growth (RGI = 51.2–55.7%). This corresponded to the lowest germination index (GI) values from 68.4% to 70.5% (
Figure 3).
The highest amounts of Na (1.4 g∙kg
−1), S (6.2 g∙kg
−1), Mn (389.8 mg∙kg
−1), and C
FA (48.8 g∙kg
−1) were recorded for C10 (
Table 3 and
Table 4;
Figure 2), while C9 was the most abundant in Ca (21.4 g∙kg
−1) and Mg (2.9 mg∙kg
−1) (
Table 3). Among all the analysed composts, C7 had the worst fertilising properties because of the smallest amounts of OM (180 g∙kg
−1), N (3.2 g∙kg
−1), C (85.8 g∙kg
−1), C
HS (17.4 g∙kg
−1), C
FA (5.65 g∙kg
−1), P (1.5 g∙kg
−1), S (0.3 g∙kg
−1), Ca (6.9 g∙kg
−1), Ni (3.4 mg∙kg
−1), Zn (45.8 mg∙kg
−1), and Cu (7.3 mg∙kg
−1) (
Table 3 and
Table 4;
Figure 1 and
Figure 2). At the same time, C7 was the least loaded with heavy metals, Cr (4.0 g∙kg
−1) and Pb (14.3 g∙kg
−1), which needs to be considered as beneficial (
Figure 5).
Due to the same composting method (AANC) applied and the used biowastes, a considerable similarity was observed between C7 and C8, as they did not differ significantly in their contents of OM, TOC, C
FA, K, Ca, Mg, Na, Fe, Mn, Ni, Pb, and Cr (
Table 3 and
Table 4;
Figure 1,
Figure 2 and
Figure 5). These composts also had comparable values of HI (13.7–17.3%), HR (20.3–23.5%), and DP (2.1–2.8) (
Table 2). Additionally, both composts had the same positive effect on seed germination and root growth, which was manifested in low SGI inhibition (10%) as well as RGI inhibition (10.2–11.6%). At the same time, a large percentage (88.2–86.6%) of GI was found to be related to this factor (
Figure 3 and
Figure 4).
When referring to the phytotoxic effects of the tested composts, the least harmful effects of C2, C4, C9, and C10 should be emphasised. These composts inhibited the germination of seeds within a very low range (from 0 to 4%), which was similar to the values for root growth (from −22.1% to −6.1%), while simultaneously the highest values of the GI index (from 87.7 to 89.6%) were determined (
Figure 3 and
Figure 4). Despite the fact that the above-mentioned composts induced plant growth and development in a similar way, they differed in terms of their abundance in macro- and micronutrients, as well as the quality and quantity of humic compounds. As it results from the data in
Table 3 and
Table 4 and
Figure 2, composts 9 and 10 generally were characterised by higher contents of nutrients in relation to the levels found in composts 2 and 4. Particularly noteworthy is the large content of S (6.2 g∙kg
−1), Na (1.4 g∙kg
−1), Mn (389.8 g∙kg
−1) and C
FA (48.8 g∙kg
−1) in C10. The highest values of HI (25.2%) and HR (37.8%) calculated for this compost need to be stressed in this respect (
Table 2).
4. Discussion
Obviously, first of all the composted wastes before application must meet the criteria of environmental safety imposed by legal regulations. The analysed composts met the Polish quality criteria except for two composts (C7 and C8), which had an organic matter content below the required 30%. These composts were prepared using the AANC method and prepared mainly from food scraps from kitchen and yard trimmings as plant residues, i.e., raw materials relatively poor in non-degradable or sparsely degradable organic compounds with a strongly polymerised structure, which would create humified organic matter. The above-ground parts of plants and food residues have a high decomposition rate, which does not promote organic matter accumulation. On the other hand, composts 5, 6, 9, and 10 did not meet the stringent European requirements regarding Zn and Ni contents (only for C5). The above information testifies to the chemical diversity of the composts proved in this study, which is primarily due to the use of sewage sludge, wastes rich in organic matter as well as macro- and micronutrients [
27], and to a lesser extent the impact of the composting methods used. A number of papers on the subject of compost application [
10,
21,
28,
29,
30] present different levels of both macro- and micronutrients, which is related to various and different composted wastes. Therefore, it is difficult to compare the data obtained in this study with those presented in the literature. Nevertheless, generally, it may be concluded that composts prepared on the basis of selected biowastes are characterised by low nutrient and organic matter contents, as evidenced by the results of analyses for composts 7 and 8. On the other hand, composts prepared based on biowastes and biodegradable waste (sewage sludge), such as composts 5 and 6, presented the largest contents of most nutrients and organic matter. The obtained data clearly indicate that there is a strong relationship between the chemical diversity of the used waste and compost abundance in nutrients and organic matter.
A separate but extremely important issue when assessing the quality of composts is not only their chemical composition, but also the degree of stability and maturity. Achieving compost stability and maturity is an extremely important element of composting, because an unstable and immature organic material may have adverse effects on plant growth and the environment. First of all, the presence of volatile chemicals, such as organic acids toxic for plants, must be underlined. Additionally, an incompletely matured compost with a higher C:N ratio can lead to a biological block of nitrogen, which is also known as “nitrogen starvation” [
31]. Therefore, before applying compost, it is necessary to assess its degree of maturity and stability. As given in
Table 1, the used composting techniques were the same in most cases, similarly as the maturing time of the composted mixture. The traditional and easier approach to evaluate compost maturity is to use the C:N value. The application of the C:N ratio as an indicator of compost maturity is widely discussed in the literature [
31]. The C:N ratio is a function of TOC and N, which changes during the composting process in organic materials, and thanks to this, it is considered a useful tool in the evaluation of compost maturity. It is widely recognised that the progress of carbon and nitrogen mineralisation is strictly related. As the decomposition progresses due to the losses of C, the C content of compostable material decreases, and with time, the N content increases, which results in the variable C:N ratio at the end of the composting process being lower than at the beginning. Unfortunately, the C:N ratio considerably varies in raw materials, and as a result, this could be a less reliable parameter; thus, it often gives a misleading indication of maturity, and it may also fail to indicate a material that is sufficiently decomposed. According to different opinions concerning the usefulness of the C:N value in compost maturity assessment, there is no unified, standardised limit value of this parameter. Azim et al. [
31] reviewed the literature data in terms of specific C:N ratio thresholds for maturity compost assessment. The range of values cited by these authors was broad, ranging from 7.8 to 20.5, with an average at approximately 12. Antil et al. [
32] indicated a value between 15 and 20 as satisfactory. In addition, Asquer et al. [
33] stated that values of C:N lower than 20 are considered an indicator of sufficient N supply for plant growth. At the same time, Bernal et al. [
34] stated that a C:N ratio lower than 12 indicates a good degree of compost maturity. According to Gomez–Brandon et al. [
35] and Singh et al. [
36], the C:N ratio within the range of 10–15 shows a stable, mature material. Taking under consideration a broad ratio of C:N of 10–20:1 as the criterion, only analysed composts 2, 4, 6, and 10 failed to meet this criterion (
Table 2).
Knowing that the humified fraction of organic compounds is the most important and responsible for fertility and quality of humic compounds, the evaluation of humification parameters of composts is essential. Since maturation also implies the formation of some humic-like substance, the degree of organic matter humification is generally accepted as a criterion of maturity and HI, HR, and DP are usually applied. It is assumed that mature composts should have an HI value above 30% [
37]. For such a criterion being adopted here, none of the composts tested reached such a value, because as indicated in
Table 2, they ranged from 3.5% (C3) to 25.2% (C10). In turn, the HR values ranged from 11.5% (C9) to 37.8% (C10). There is no limit HR value specified in the literature, which could be helpful in assessing the compost maturity. Thus, it makes it difficult to evaluate the obtained results in this study. Nevertheless, outcomes presented by Bustamante et al. [
28] or Asquer et al. [
33] indicated comparable values of HR and HI. Alvarenga et al. [
38] stressed the considerable variation between individual composts in terms of respective HR and HI values.
The C
HA:C
FA ratio is widely used to describe the relative speed of HA and FA transformation, as well as the maturity of compost. Iglesias-Jimez and Pérez-García [
39] stated that a value of the C
HA:C
FA ratio higher than 1.9 indicates compost maturity. In turn, Azim et al. [
31] on the basis of a literature review, stated that the correct threshold value of the polymerisation degree needs to be greater than 1. On the other hand, Alavarenga et al. [
38] considered the limit value of 2.5 for the C
HA:C
FA ratio. Taking into account that threshold, it may be assumed that only composts 2, 5, 6, 7, 8, and 10 were well matured, because the values obtained for them ranged from 2.1 to 2.8 (
Table 2). Optical density expressed as Q
4/6 ranging from 3.23 to 8.8 indicated a successful maturation of composts [
40]. This threshold was met by most of the composts except for C5 (9.2) and C6 (17.3) (
Table 2).
The stability of composts is commonly evaluated using biological methods, such as e.g., the germination index [
17,
21,
29,
41,
42]. The application of biotests is considered to be a sophisticated method to evaluate environmental pollution, supplementing chemical methods. The data given in the literature on the limited threshold of GI describing the maturity of composts are inconsistent. In relation to the obtained results, Antil et al. [
32] proposed GI > 70% as a threshold value, which may be accepted as an indication for compost maturity. According to Sangamithirai et al. [
43], a phytotoxin–free and mature compost is characterised by a GI value of more than 80%. In addition, Jakubus and Bakinowska [
41] indicated reliability in compost evaluation using a GI threshold over 80%. On the other hand, Komilis and Tziouvaras [
44] stated that a GI value greater than 100% indicates a beneficial effect on seed growth and therefore identifies a mature compost, whereas Ko et al. [
45] reported that compost having a GI value > 110% was considered mature. Referring to the most frequently quoted 80% GI value, composts numbered 2, 4, 7, 8, 9, and 10 met these criteria.
Despite the opinion on GI being rapid and sensitive, it has also been subjected to criticism, because it is a tedious bioassay to perform, as it requires about 48–72 h to run and involves complicated operations, while the sensitivity of plant species to phytotoxic chemicals in compost may vary. Unfortunately, data obtained on the basis of that biological assay are neither comparable nor standardised. Therefore, in the present study, apart from the popular GI, also a 3-day Phytotoxkit test was applied. This bioassay meets the requirement of the ISO standard and evaluates the rate of inhibition for seed germination and root growth. The results of this test were consistent with the previously presented finding of GI recorded for the above-mentioned composts and confirmed their lowest degree of inhibition for seed germination and root growth. The application of the Phytotoxkit test to evaluate the quality of composts prepared from various organic waste should be considered as an innovative approach to the issues raised. The obtained data showed its considerable usefulness, indicating that it can be a valuable supplementation of other methods.
The lack of harmonised standards and threshold values for individual indexes makes it difficult to interpret the analysed composts in terms of their maturity and stability. The results of the research carried out clearly revealed these imperfections, indicating at the same time the advisability of further research in order to develop common and uniform criteria for assessing the quality of composts prepared from various organic wastes. Especially based on the above data, it may be concluded that compost maturity was assessed differently depending on the applied index. From among the examined group of composts, the maturity of the following composts was most often assessed positively: 2, 3, 5, 6, 7 and 8. With regard to compost stability assessed by the bioassay, composts 2, 4, 7, 8, 9 and 10 showed the lowest phytotoxic effect.
5. Conclusions
As confirmed by statistical analysis, the differences in the chemical composition of composts primarily resulted from the use of raw material for composting, and to a lesser extent from the process technology used. Despite the fact that composts prepared with biowastes using the AANC method (C7 and C8) were evaluated as fertilisers with low abundance in nutrients and organic matter, they were characterised by favourable stability and maturity parameters. Similarly, the opinion concerning the quality of composts could be related to the composts being a mixture of biodegradable wastes and biowastes collected separately by the inhabitants of a medium-sized town (C2) and a mixture of biowastes and manure in a 1:1 ratio (C9). The above-mentioned composts 2 and 9 were characterised by a slightly higher abundance in nutrients and organic matter in relation to composts 7 and 8. As a result, these types of fertilisers may be recommended for small-scale vegetable cultivation, ornamental gardens, or the maintenance of urban greenery, where cultivated plants do not have such high nutritional requirements. Taking into account the high contents of nutrients and organic matter and the satisfactory quality of humic compounds, composts prepared with a share of sewage sludge (C5 and C6) are worth recommending as organic fertilisers used for reclamation of post-industrial areas, where the soil production capacity should be rebuilt in the first stage. Due to the strongest phytotoxic effect of this type of compost, it should not be proposed for horticultural and agricultural crops.
Referring to the indexes evaluating maturity and stability of organic fertilisers applied in the presented studies, it should be stated that there are no uniform critical values that can be applied to compost assessment in a reliable and universal manner. Especially the very popular indicator such as the C:N ratio should be interpreted as not fully descriptive of the compost maturity index, while more reliable parameters such as DP should be taken under consideration for compost evaluation. Based on the results of the author’s research for evaluation of composts, the bioassay may be recommended, as well as the degree of polymerisation of humic compounds expressed by the DP (CHA:CFA ratio) index.
Summing up, composts as organic fertilisers were found to be a valuable source of nutrients and organic matter. From the economic aspect, it should be underlined that raw materials used for composting are easily available locally, and thus the final product is relatively cheap and marketable for gardeners or farmers in comparison to expensive mineral fertilisers. In addition, local authorities responsible for managing organic waste should opt for this form of their recycling, increasing the attractiveness and popularity of this type of fertiliser.