1. Introduction
Current manufacturing developments and the vast extraction of traditional fossil energy have led to increasing environmental pollution and energy shortages. New energy resources, such as wind and solar, renewable and environmental, must, therefore, be developed to substitute conventional fossil fuel sources [
1,
2]. Nonetheless, renewable energy sources generate a low voltage, far from the voltage required in different applications. Therefore, the demand for DC-DC converters is on the rise, and much research is being conducted on this topic. Other applications, such as high-intensity discharge lamps, electric vehicles, fuel cell energy sources, solar photovoltaic energy sources, X-ray systems, DC microgrids, etc., also need high-step voltage converters [
3]. In principle, the traditional dc-dc boost converter delivers a large voltage gain with a duty ratio nearer to unity. Practically, nevertheless, the dc-dc converter’s voltage gain is restricted by the internal elements of the capacitor and inductor, diode reverse recovery issues, large duty cycle, device rating, and electromagnetic interference [
4,
5].
Many topologies of power converters have recently been published in literature using many boosting methods. The converters based on the transformer, such as H-bridge, push-pull, flyback, etc., may be decent choices to attain high gain and isolation. Since the converter requires a high-frequency transformer, an additional circuit to handle the transformer’s leakage inductance is a must; therefore, the converter structure is large and costly [
6,
7]. In addition, large voltage stress is due to the transformer’s leakage inductance on the semiconductor devices. Therefore, the clamp networks are essential to recycle the energy released by the leakage inductance and to reduce the voltage stress of the semiconductor switches [
8]. Recently, the converters based on the coupled inductor are famous for achieving a high voltage gain without/with isolation; nevertheless, additional voltage clamp circuits are required to reduce the inductor leakage inductance effects, which further increase the overall price of the converter. Additional losses related to the voltage clamp devices are also introduced [
9,
10]. Other possible solutions may be quadratic and cascaded converter structures. Still, a high-voltage device continues to be required, as the switch voltage is equivalent to the output voltage of the converter.
Moreover, two or more dc-dc converters in the cascaded structure led to circuit difficulty and higher costs. In addition, complex control is needed because the gain of the converter is extremely non-linear, and two or more semiconductor devices have to be coordinated. Many converters are developed using SI, hybrid SI, switched-capacitor, voltage lift, voltage multiplier, and interleaved structures to improve the performance of the traditional converters [
11,
12,
13]. However, there are numerous power conversion stages, and the MOSFET switch stress is equivalent to or larger than the output voltage. In addition, the converters with various multiplier cells increase the converter’s dimensions and hence the overall cost. Various converters are discussed in the literature to decrease the MOSFET device’s current and voltage stress and achieve a large voltage gain at a low-duty ratio [
14,
15].
However, the DC-DC converters discussed above are complicated, and the converter voltage gain is inadequate for various real-time systems. Therefore, the efficient concept of Z-source structure was first suggested in 2003 [
16]. Two X-shape capacitors and inductors form the Z-source impedance network. The Z-source structure was first tested with the DC-AC inverters for boost and buck capability. In the meantime, due to various advantages of the Z-source structure, it was applied successfully to the solar photovoltaic and fuel cell system applications. In particular, the QZS inverter has benefits such as less capacitor voltage stress, continuous input current, and the output and input common ground. The Z-source and QZS networks can also be used to improve the converter output gain. A Z-source converter is discussed in [
16], and the converter voltage gain is greater than the conventional converter voltage gain. In [
17,
18], an alternate Z-source converter is discussed in which a Z-source system replaces the inductor in the traditional converter. In [
19,
20,
21,
22,
23,
24], an MQZS converter was presented, delivering a larger voltage gain than the other converters in the literature. Nevertheless, in many industrial applications, the voltage gains from the Z-source converters remain insufficient, so the design of higher step-up converters remains challenging.
Therefore, this paper proposes a modified MQZS structure with a single-stage SI network connected with the traditional step-up converter, decreasing the voltage stress of the MOSFET and improving the voltage gain more than the conventional QZS-based boost converter. The remainder of this paper is organized as follows. The working concept of the Continuous Conduction Mode (CCM) converter is presented in
Section 2.
Section 3 discusses the steady-state study of the suggested MQZS converter under CCM and parameter selection.
Section 4 explains the simulation outcomes to prove the theoretical discussions. The hardware results and performance assessment are discussed in
Section 5, and
Section 6 presents the conclusion.
2. Operation of the Proposed MQZS DC-DC Step-Up Converter
Figure 1 illustrates the structure of the existing QZS boost converter [
17,
18]. The SI circuits are used to expand the voltage gain more than the traditional boost dc-dc converter. Nevertheless, the voltage strain over the MOSFET raises with the converter gain; therefore, the MOSFET voltage stress is equal to the load voltage of the QZS converter. Therefore, the suggested converter voltage gain is slightly increased by the slight modification in the connection, and the voltage stress is condensed by connecting one diode and capacitor extra than the converter shown in
Figure 1 [
25,
26]. The circuit structure of the suggested MQZS boost converter is depicted in
Figure 2, in which the inductors are discharging series and charging parallel to realize a high voltage gain.
As indicated in
Figure 2, the converter is different from the traditional QZS converter in two ways. Firstly, the connection of the output diode,
D5, is changed to the junction point of the diode,
D1,
D2, and
L2 (as indicated with red color arrow mark), which improves the voltage gain. Secondly, the clamping network that contains one capacitor,
C1, and one diode,
D4, is added (as indicated in the pink color box line), reducing the stress on the MOSFET switch. The following hypotheses are formulated before beginning the circuit analysis.
The selected power semiconductors are ideal
The proposed converter is working in the mode of continuous conduction
Pulse-width modulation is the control approach utilized by switch S
The converter operation is divided into two modes. The theoretical waveform is illustrated in
Figure 3. The current path during the two modes is illustrated in
Figure 4.
Mode-a (t0 − t1): Mode-a starts when the MOSFET device,
S, is turn-on. The current path is illustrated in
Figure 4a. During this mode, the inductors,
L1 and
L2, charge over the diodes,
D3 and
D1. The diode,
D5, is forward biased due to its higher potential and distributes the required energy to the load. In addition, the C
1 is getting charged through the load and the diode,
D5. The diodes
D2 and
D4 are reverse-biased due to their lower potentials. The mode ends when
S is switched off at
t =
t1. Throughout this duration, the output capacitor,
C2, stores the energy.
Mode-b (t1 − t2): When the
S is switched off, mode-b starts at
t =
t1. The current path is illustrated in
Figure 4b. The diodes
D1,
D3, and
D5 are turned off due to their lower potential, and the diodes
D4 and
D2 are forward biased due to their higher potential points. During this mode, both the inductors start discharging the energy through the diode
D2, the diode
D4 and the clamp capacitor
C1. Thus, the MOSFET voltage stress is condensed by the
C1 and the diode,
D4. The output capacitor delivers the energy required by the load during mode-b. When the switch,
S, is switched on, this mode is terminated at
t =
t2.
4. Simulation Results
The electrical specification and various variables of the proposed MQZS converter are recorded in
Table 1. The simulation was performed using PLECS standalone software installed in a laptop with a 4.44 GHz clock frequency and 16 GB RAM. The same has been included in the revised version. The performance of the MQZS converter is validated using the specifications listed in
Table 1.
As discussed earlier, the converter is simulated with the input voltage at 30 V and a constant load at 100 Ω (400 W). The MOSFET duty cycle is adjusted to 70% to reach the required voltage gain of 6.67. First, the simulation waveforms for the
Vds and
, and the current stress of
S and
D4 are demonstrated in
Figure 5.
From
Figure 5, the MOSFET switch voltage stress and
D4 are noticed as 170 V and are equal to the theoretical discussion as per Equation (8). To prove the converter operation in CCM, the current wave shape of inductors is seen in
Figure 6. It is seen from
Figure 6 that the converter is operating at CCM (current never reaches zero at any instant). The inductor’s average current is equivalent to 6.95 A.
The current and voltage stresses of the diodes,
D1–
D3 and
D5 are demonstrated in
Figure 7. From
Figure 7a,b, the diode voltage stress,
and
are equivalent to 70 V. The diode voltages,
, are equal to 30 V, as realized in
Figure 7c. The voltage across the diode,
, is equal to 100 V, as realized in
Figure 7d. All the voltages are equal to the theoretical values as per Equations (5), (9) and (10).
Figure 8 depicts the waveforms for the capacitor, the source voltage, and the input current. From
Figure 8a, it is noticed that the capacitor voltage is equal to 170 V as per Equation (4). The main benefit of the MQZS step-up converter is a continuous input current. The input current is continuous, as seen in
Figure 8b.
Figure 9 illustrates the output voltage and current waveforms of the MQZS converter. It is noticed from
Figure 9a that the load voltage is equal to 200 V with the output current of 2 A, as seen in
Figure 9b.
From the above simulation results, the MQZS converter performs better according to theoretical analysis, as noted. In addition, the proposed MQZS DC-DC converter accomplishes better performance than the traditional QZS converter.
5. Hardware Results
The experimental prototype of the suggested MQZS converter with a 400 W rating is made and verified in the research laboratory environment. The electrical specification of the MQZS converter is recorded in
Table 1, and the devices required for the prototype are recorded in
Table 2.
The duty cycle of the MOSFET device is tuned to 70% to obtain the essential voltage gain from the proposed converter. The MQZS converter’s current and voltage waveforms are seen in
Figure 10 for
Vin = 30 V and
Vout = 200 V. The switching frequency of the MOSFET switch is 100 kHz. The source voltage and input current waveform are illustrated in
Figure 10a. As seen in
Figure 10a, the input voltage is 30 V, and the average input current is 14.2 A. It is also noted that the source current is continuous. The voltage across
L1 and
L2 is depicted in
Figure 10b. The average current of both
L1 and
L2 is equal to 7.08 A, and the CCM operation of the converter was also observed. In addition, the output voltage and output current of the MQZS converter is depicted in
Figure 10c.
As seen in
Figure 10c, the output current of the MQZS converter is equal to 2.1 A, and the output voltage of the converter is equivalent to 198.2 V. The MOSFET switch voltage stress is less than 200 V as per Equation (8), and it has been seen in
Figure 10d. In addition, the continuous conduction mode of the converter is confirmed, as seen in
Figure 10d. The voltage waveforms, such as
,
,
and
, are depicted in
Figure 11.
As seen in
Figure 11a, the voltage of the diode
D1 is less than 70 V, and the voltage across the diode
D2 is less than 30 V, and these voltages are the same as per Equation (5) and Equation (9).
Figure 11b displays the voltage waveforms of
and
, and the values of these voltages are equal to 58 and 200 V, respectively, as per Equation (5) and Equation (10). The capacitor voltage,
, waveform is illustrated in
Figure 11c and equals less than 170 V.
The proportional-integral (PI) controller verifies the dynamic response of the MQZS converter. The output voltage of the converter is sensed using the voltage sensor, LEM LV 25-P, and fed to the comparator to compare the actual voltage and converter’s reference voltage. The controller gain of the PI controller is chosen as
Ki = 0.01 and
Kp = 0.5 based on the trial-and-error method. The voltage control can control the output voltage at 200 V, even if the input voltage is continuously changed, as shown in
Figure 12, from 35 to 25 V. The source voltage is retained as 30 V at the beginning, and at t = 5 s, the source voltage is changed to 35 V and changed to 25 V in 10 s again. The proposed converter’s dynamic output voltage waveform for the change in input voltage is seen in
Figure 12. As seen in
Figure 12, the MQZS converter maintains a constant output voltage, regardless of the input voltage change.
It is fair to compare the suggested converter with the conventional QZS converter. Therefore, the converter performance comparison in terms of the capacitor voltage, the output voltage, the switch voltage stress, and the input current with the traditional converter is listed in
Table 3.
From
Table 3, the switch voltage stress and capacitor voltage stress of the proposed converter are lesser than the traditional QZS converter for the same output voltage. The traditional converter can obtain the output voltage of 109.09 V at 57% of the duty cycle, whereas the proposed converter can obtain the same output voltage at 45% of the duty cycle. From these discussions, it is concluded that the performance of the proposed converter better than the traditional QZS converter in all aspects. Thus, the dimensions and cost of the suggested MQZS converter have been reduced mostly.
Figure 13 displays the voltage gain characteristics of the MQZS converter and other similar converters in the literature. Besides, the MQZS converter voltage gain by considering the internal elements of various components is also demonstrated in
Figure 13.
Figure 13 shows that the voltage gain is reduced at a high duty cycle due to the influence of parasitic components of various devices. Therefore, it is not advisable to operate the converter at a high duty cycle, i.e., beyond 70% duty cycle. In addition, the high duty cycle also reduces the conversion efficiency due to high voltage drop across the parasitic elements and the conduction power losses. The efficiency curve assessment of the suggested MQZS converter with the other converter structures is illustrated in
Figure 14. As seen in
Figure 14, the effectiveness of the suggested MQZS converter is high due to a smaller number of components when related to the converters discussed in the literature. The maximum efficiency of the MQZS converter at 300 W is 94.2%, and the converter’s efficiency at full load is equivalent to 93.1%.
6. Conclusions
This paper comprehensively studied and analyzed the traditional QZS converter and modified the QZS dc-dc boost converter with one MOSFET switch. The proposed MQZS converter is an enhanced version of the traditional QZS converter, as it offers a high voltage gain, similar to the QZS converter. The prototype of the proposed MQZS dc-dc converter is made and experimented with in the laboratory environment. The experimental outcomes confirm the theoretical discussion and simulation results of the MQZS dc-dc converter. The operation, analysis, and parameter selection of the proposed MQZS converter were detailed in this paper. Moreover, the performance comparison is made with converters in previous works, and it is noted that the proposed MQZS converters offer high performance in the non-isolated converter category. The MQZS dc-dc converter can attain high output voltage gain with less voltage switch stress of the MOSFET, diodes, and capacitor. It also has benefits such as low cost and high-power density. Thus, the suggested MQZS converter is more appropriate for renewable energy systems that require a high output voltage from a low source voltage. In the future, the proposed converter can also be extended to various applications, such as electric vehicle power train systems, solar photovoltaic powered pumping systems, DC microgrid systems, etc.