1. Introduction
Agricultural tractors deal with various agricultural operations, such as plows, rotary, and balers, by towing implements attached at PTO [
1,
2]. The demand for agricultural tractors is dramatically increasing due to the application of advanced technology [
3]. According to Mordor Intelligence statistics [
4], the global market of the agricultural tractor, which is an emerging market, has an expected annual growth rate of 4.02% in 2025 than that in 2020. The EconomyChosun [
5] reported that the annual growth rate of the tractor market is comparatively higher than that of automobiles (6.8%) and heavy equipment (1.0%). It also reported that the annual demand for global tractors is expected to grow from 2.55 million units in 2013 to 3.92 million units by 2023.
The EconomyChosun [
5] again stated that the tractor market share of North America and Western Europe is gradually decreasing, whereas the Asia-Pacific regions, including China and India, are on trend to increase. Additionally, the tractor market size of Asia-Pacific was reported to be three times that of the Western European market. However, based on the EconomyChosun report, the global tractor market is dominated by John Deere (USA), CNH (UK), Kubota (Japan), and AGCO (USA), which are called the “Big 4”, accounting for almost half of the tractor market. The latecomers, such as Korean, Chinese, and Indian companies, are competing for the rest of the market. To compete with the largest tractor manufacturing company in the global market, and to fulfill consumers’ demands, Korean tractor-manufacturing companies are highly concerned with the development of various agricultural machinery with sophisticated technology, as well as the quality and durability of their agricultural machinery.
Recently, tractor power has been focused on hydraulic power, such as the hydraulic transmission, clutch, brake, steering, hydraulic pump, loader, PTO (power take-off), proportional valve, and so on [
2,
6], because it is highly precise, smooth, and comfortable for the driver [
7]. However, Shin et al. [
8] reported that the quality level of the hydraulic components of agricultural machinery in Korea was almost 68.4% in 2015, which indicated very low reliability. Therefore, the reliability test for the hydraulic system of agricultural machinery should be conducted.
The hydraulic pump is the crucial or core component, or heart, of the entire hydraulic system of a tractor. Zhonghai et al. [
9] conducted the reliability analysis for highly reliable aircraft hydraulic systems, such as hydraulic pistons, hydraulic actuators, and landing gears. Additionally, he proposed a quick method, which was for the reliability estimation of hydraulic piston pumps, called the engineering-driven performance-degradation analysis method. Liu et al. [
10] proposed the reliability test method of the hydraulic pump based on an acceleration life test. Tang et al. [
11] stated that the hydraulic pump is the core power source of a hydraulic transmission system and developed a normalized convolutional neural network (NCNN) framework for fault identification. Further, he improved the model to tune automatically using the Bayesian algorithm, and the improved model was named BNCNN. Therefore, the hydraulic pump of the hydraulic system of a tractor was selected in this study for reliability analysis.
The reliability assessment process is generally adopted to access the span life, reliability level, and failure rate [
12,
13]. The two types of tests were also stated: one is a statistical-based reliability test (SRT), which requires engineering elements (failure mode and mechanism, test equipment and conditions, and cost limits); another is the engineering-based reliability test (ERT), which requires a big data set and statistical analysis. He further stated that both the SRT and ERT are combinedly used for the reliability test. Therefore, to ensure reliable and sustainable mechanization, it is high time to develop a reliability assessment technique for the hydraulic system of agricultural machinery.
There are two types of SRT, which are the acceleration life test (ALT) and the accelerated degradation test (ADT) [
14]. Between the two, the ALT is widely applied to practically assess product reliability because it is highly accurate, quick, and economical [
15]. Chen et al. [
12] presented an overview of the ALT and stated that ALT applications are recently increasing in the engineering research field with product reliability and the complexity of actual operational conditions. In addition, it is used as an engineering solution to improve the technical level of various instruments and equipment. Tkáč et al. [
16] conducted the durability laboratory test, only for the hydrostatic pump of agricultural machinery, based on biodegradable oils. Tkáč et al. [
17] also conducted the ALT in the indoor test of the hydrostatic pump for agricultural machinery. However, the actual field conditions were not considered in those studies. Therefore, this study approaches the reliability assessment techniques by considering the real field operations of a tractor.
This is a basic study on the development of a reliability assessment method for the hydraulic pump of agricultural machinery to ensure reliable and sustainable machinery performance. In this study, major agricultural operations (plow and rotary tillage, and bale and wrapping operations) were selected for the load measurements of the tractor. The acceleration factor was calculated using the equivalent load of the field experiments. The nobility of this research is the development of the reliability assessment method its verification, using the measured equivalent load of agricultural field operations. The specific objectives are as follows:
- (i)
To develop a load-measurement system for the agricultural tractor used in this study
- (ii)
To develop a reliability assessment method for the hydraulic pump of an agricultural tractor
- (iii)
To evaluate the developed reliability assessment method by the measured equivalent load during agricultural major operations
- (iv)
To estimate the lifetime of the hydraulic pump using the acceleration factor that represents the lifespan of a tractor
2. Materials and Methods
2.1. Tractor Configurations
In this study, a 78 kW MFWD (mechanical front wheel drive) tractor (07, TYM Co., Ltd., Gongju, Korea) was used to develop the reliability assessment method. The dimension of the tractor (Length × Width × Height) were 4225 × 2140 × 2830 mm, and the empty tractor weight was 3985 kg.
The engine-rated power and torque at the rotational speed of 2300 rpm were 78 kW and 324 Nm, respectively. The tractor transmission consisted of a total of 64 gear stages (32 forward and 32 reverse), including 4 mechanical synchromesh-type driving shifts (1, 2, 3, and 4), 2 power shifts (high and low), and 4 mechanical constant-type range shifts (C, L, M, and H). The maximum PTO (power take-off) power and torque were 69 kW at 2300 rpm and 360.7 Nm at 1400 rpm. The hydraulic pumps were specified with 24 cc/rev of the main pump, and 12 cc/rev of the auxiliary pump. The specifications of the tractor are listed in
Table 1.
2.2. Load-Measurement System
2.2.1. Hydraulic System
The tractor hydraulic system included two hydraulic pumps (main and auxiliary). The hydraulic pressure sensors were installed in the tractor to measure pressure generated by the hydraulic pump (main and auxiliary). The main pump (
Figure 1a) was performed to operate the implements, and the auxiliary pump (
Figure 1b) was performed for the hydraulic steering used to turn the tractor. The pressure sensors installed in the input and output pipe of the pump are shown in
Figure 1.
The pressure sensor (HySense PR 130, HYDROTECHNIK, Germany) was configured with the range of 0~250 bar, and it measured the relative pressure using the piezo-resistive method. The details of the specifications of the pressure sensors are listed in
Table 2.
2.2.2. Data-Acquisition System (DAQ)
The data-acquisition system (DAQ) was installed in the test tractor to read the pressure data of the main and auxiliary pumps during major agricultural operations. CRONOS compact CRC−400−11, IMC, Germany was used in this study, which is shown in
Figure 2a. A data-monitoring system was also installed in the tractor cabin to monitor the real-time load data generated by the hydraulic pump during agricultural operations in the field, which is shown in
Figure 2b. The data-monitoring system was capable of displaying and storing the real-time data during the turning of the tractor or lifting implements at the same time.
The dimensions (length × width × height) of the DAQ system were 353 × 155 × 264 mm, and the weight of the device was 10.5 kg, which was configured with a sampling rate of 400 kS, and the maximum module slots were 11. The engine rotational speed was collected using CAN data, and the hydraulic pressure of the pump was measured using the pressure sensors installed in the test tractor. The details of the specifications of the DAQ system are listed in
Table 3.
2.3. Experimental Conditions
2.3.1. Operational Conditions
In this study, the tractor was operated by an experienced operator using a conventional method to improve the reliability of the tractor. The plow and rotary tillage operations were conducted at 150~200 mm of the tillage depth, which is commonly used in Korea, especially in paddy fields [
18,
19,
20,
21,
22]. Additionally, according to the moldboard specifications, the maximum working depth was 200 cm. Wang et al. [
23] also stated that plow tillage was conventionally conducted at a depth of 15~18 cm. The moldboard plow specifications are listed in
Table 4.
The plow tillage was performed at gear stages of M2 high and M3 low, whereas the rotary tillage was conducted using the gear stages of L3 low and L3 high, and the PTO gear stages were selected at P1 and P2. In the case of the baler operation, the pressures were measured for the M2 low-gear stage, whereas the PTO gear stages were selected at P1 and P2. However, the wrapping operation was conducted at the driving gear stage of M4 low, and was replicated 3 times. The field operation conditions, with the tractor speed, are listed in
Table 5.
2.3.2. Soil Conditions
To experiment with the measurements of the hydraulic pressure of the hydraulic pump used in the tractor, two experimental sites (Seosan and Gongju, Republic of Korea) were selected. The soil samples from the selected experimental sites were collected, and the soil texture was analyzed using the USDA soil texture triangle, physical, and mechanical properties to determine the field condition. The water content, hardness (cone index, CI), shear force, electrical conductivity (EC), and temperature of the soil were measured. The soil samples were collected, and physical and mechanical properties were measured, randomly at 10 points of each experimental site. The soil analysis results for both fields are listed in
Table 6.
2.4. Equivalent Load Estimation
In agricultural operations, the load is an irregular shape due to uneven fields, variable soil hardness with stones and crop straw, tractor vibrations, and so on. However, the unique load that represents the agricultural work is required to develop the reliability evaluation criteria. In this study, the equivalent load of the hydraulic pump during agricultural operations could be expressed as an equivalent pressure. The Palmgren–Miner rule, based on cumulative damage, is usually used to estimate the equivalent load for each agricultural operation [
24]. The Palmgren–Miner rule equation is shown in Equations (1) and (2).
where
is the equivalent pressure of
ith operation (MPa);
is the equivalent pressure of the hydraulic pump (MPa);
is the ratio of
ith relevant frequency of the pressure to the total frequencies of the pressure;
is the pressure (MPa) for
ith operation;
is the annual usage time (h) for
ith operation; and
is the coefficient of fatigue damage. The fatigue-damage coefficient was considered to be 8 [
13].
In the case of the rotational speed, the equivalent rotational speed was estimated using Equations (3) and (4).
where
is the equivalent rotational speed (rpm) for
ith operation;
is the rotational speed (rpm) for
ith operation;
is the equivalent rotational speed (rpm); and
is the total usage time (h).
2.5. Acceleration Life Test (ALT)
The acceleration life test (ALT) is comparatively a time-consuming and costly experiment, especially for agricultural machinery such as tractors, during field operations. To solve this issue, the strategy of a failure-free lifetime test applying a high-stress acceleration method was adopted for the reliability assessment of the hydraulic pump of a tractor. This adopted test method can estimate the acceleration test time using the calculated equivalent hydraulic pressure of the hydraulic pump.
However, no evaluation standard or method can apply the equivalent pressure of the hydraulic pump. In 2008, the Korean Agency for Technology and Standards introduced the RS-B-0063 for the gear pump of agricultural machinery. This standard stands to evaluate the performance and reliability test methods of gear pumps for agricultural machinery, especially for the actual operations of the agricultural machinery. According to this standard, the ALT was performed for 10 samples up to 1000 h at
, and the lifespan of 1900 h was guaranteed, where it reached 80% of the confidence level [
25]. The evaluation test conditions of the standard are as below:
At the maximum input rotational speed, hold on for 5 s under the no-load condition, and then 5 s at the maximum load condition.
Perform comprehensive performance tests before and after the ALT is completed.
Perform representative performance tests at 50% of the total life test time.
The evaluation criteria of the standard are as follows: (i) both the comprehensive and representative performance must satisfy the evaluation criteria; and (ii) all samples should have no failure and satisfy the evaluation criteria of the comprehensive performance test after the ALT. Therefore, the RS-B-0063 was used in this study to evaluate the ALT of the hydraulic pump of the tractor.
The failure-free lifetime of the hydraulic pump of a tractor during field operations was estimated using Equation (5).
where
is the failure-free test time (h) of the hydraulic pump of a tractor;
is the lifespan of the hydraulic pump (h);
is the confidence level;
is the number of the test sample (h);
is the reliability (
< 1); and
is the shape parameter, which is considered to be 2.0 [
26].
In this study, the failure-free test time (T) was set as 3122 h when the number of the sample (N) was 1. The test time was calculated to be almost 14,549 h based on the lifespan (
) at 90% of the confidence level (CL) [
27,
28].
means that 10% of the hydraulic pump may be damaged within the warranty period. As the ALT is a time-consuming test using an indoor test device, the acceleration factor was estimated using Equations (6) and (7).
where
is the acceleration factor of the hydraulic pump of a tractor;
is the hydraulic pressure (MPa) at test conditions;
is the acceleration test time (h) of the hydraulic pump; and
is the rotational speed (rpm) at test conditions.
In this study, the harshness pressure of the hydraulic pump was set at 20 MPa and the rotational speed was set at 2100 rpm, which is the engine-rated speed to determine the acceleration factor of the hydraulic pump of the tractor.
2.6. Analysis Method
In this study, statistical approaches were used to analyze the hydraulic pressure and engine rotational speed measured for various gear stages and major agricultural operations. A one-way ANOVA (analysis of variance) test and Duncan’s multiple-range test (DMRT) were performed to analyze the significance of the hydraulic pressure and engine speed to the gear stages for each agricultural operation. The software used for the statistical analysis was IBM SPSS Statistics (SPSS 25, SPSS Inc., New York, NY, USA).
5. Conclusions
This study emphasized the development of the reliability test method for the hydraulic pump of a tractor during major agricultural operations (plow, rotary, baler, and wrapping) at various driving and PTO gear stages. In this study, the hydraulic pressure for both the main and auxiliary pump, as well as the engine rotational speed, were measured and converted to the equivalent pressure and engine speed for each agricultural operation using a mathematical formula. However, the statistical analysis showed that there is a significant difference between various gear stages for the same agricultural operation. Therefore, the overall equivalent pressure and overall engine speed were calculated to determine the acceleration lifetime. The developed reliability test method was evaluated by RS-B-0063, which is the existing reliability evaluation standard for agricultural hydraulic gear pumps. The major findings of this study are listed below:
- (i).
The average equivalent pressure and engine speed for plow tillage were calculated at around 5.44 MPa and 1548.37 rpm, respectively, whereas the average equivalent pressure and engine speed for rotary tillage were almost 5.70 MPa and 2074.73 rpm, accordingly. In the case of baler and wrapping operations, the average equivalent pressure and engine speed were approximately 11.22 MPa and 2203.01 rpm, and 11.86 MPa and 913.76 rpm, respectively.
- (ii).
The overall hydraulic pressure of the pump and the engine rotational speed were found around 10.07 MPa and 1512.93 rpm, respectively. The acceleration factor was calculated using the overall pressure and engine speed accounting for 336. Additionally, the fault-free test time was calculated 44 h for the hydraulic pump of the tractor.
In summary, it was observed that the warranty lifetime was increased by 1.64 times at 90% of the confidence level than that 80% of the confidence level. The evaluation results proved that the developed reliability test method for the hydraulic pump of a tractor satisfied the standard criteria. In addition, this approach was an efficient, cost-effective, and time-saving technique to assess the reliability of the hydraulic pump of a tractor. We also believe that this technique contributes to the literature, especially regarding the reliability assessment of the off-road vehicle. Therefore, it could be said that the developed reliability test method could be applicable to the hydraulic pump of the tractor during agricultural field operations.