1. Introduction
Smart wearable devices that are compact, lightweight, and ergonomic are quickly becoming mainstream. With the development of communication technology, smart glasses have gradually received widespread attention, such as the Google smart glasses in 2012, smart goggles Form Swim Goggles in 2019, and the recent Facebook smart glasses in 2021. The antenna design specifications of smart glasses mostly use Bluetooth and Wi-Fi wireless communication for indoor communication and entertainment. Moreover, they communicate with mobile phones and wearable devices via Bluetooth [
1,
2,
3]. However, with the rapid development of smart glasses research, smart glasses devices will no longer only use Bluetooth or Wi-Fi antenna technology, such as a WiGig array module antenna design on the frame [
4] or LTE multi-band antenna design on the temple [
5].
At present, there are various types of antennas in smart wearable devices and smartphones. These devices usually demand ultra-wideband (UWB) operation. Due to the limited antenna design space, slot antennas or microstrip antennas are the best choice for these work environments [
6,
7,
8,
9,
10,
11,
12]. In recent years, articles on the configuration of slot antennas for wireless communication products have emerged. For example, a notebook device uses the shaft block to design the slot antenna to produce a 2 × 2 MIMO antenna system for low frequencies of 700–900 MHz and high frequencies of 1.7–2.6 GHz [
7]. In [
8], the smartphone uses the coupling effect between the inverted-F antenna and the slot to design a 2 × 2 LTE low-frequency antenna and a 4 × 4 LTE high-frequency antenna in a tiny space. Finally, [
10] proposes a smartwatch with a 2 × 2 MIMO antenna system in a metal frame to match the frequency band to achieve the required coverage according to the slot antenna and circuit components.
In the fourth-generation (4G) mobile networks, 2 × 2 MIMO antenna systems have been widely used in various wireless communication products [
13]. However, for fifth-generation (5G) mobile communications and Wi-Fi 6 wireless indoor communications, more antennas are needed to support the ultra-high broadband transmission rate in the ultra-high-frequency band and better transmission path reliability. Moreover, it will be a major challenge for antenna researchers to set up a MIMO antenna system with high isolation in space-constrained smart wearable devices, and an asymmetrical antenna architecture can compensate for the problem of poor isolation [
14,
15,
16,
17,
18].
The antenna of smart glasses is most often placed on the temples. When the antenna is closer to the human body, a lower specific absorption rate (SAR) is required to comply with the regulations of various countries [
19,
20]. The SAR value is limited to 1 g 1.6 W/kg under the standard established by FCC KDB 248227 in the United States [
21], while Europe and the Institute of Electrical and Electronics Engineers (IEEE) require the SAR value to be limited to 10 g 2 W/kg [
22]. Because the Wi-Fi 6e working frequency is greater than 6 GHz, FCC needs to measure the power density (PD), and its limit value is
[
23].
In the current research, articles on the application of Wi-Fi 6e frequency to smart glasses have not yet been published. Therefore, this paper proposes a Wi-Fi 5G and Wi-Fi 6e dual-band 4 × 4 MIMO antenna system for plastic glasses. In this article,
Section 2 describes the design process of the glasses antenna and simulates the slot size and circuit matching.
Section 3 observes the impact caused by the antenna approaching the head and the simulation of the head SAR value. In
Section 4, we describe a physical glasses antenna based on the previous simulation results and provide measurements of the antenna gain, antenna efficiency, and 2D radiation pattern; we then provide a comparison table with other references. Finally, this paper is concluded in
Section 5.
2. Antenna Design
Figure 1 shows the 4 × 4 MIMO slot antenna system applied to the Wi-Fi 6e band proposed in this paper. The antenna system can be divided into an inverted-F antenna and a metal ground plane. The inverted-F antenna is manufactured by Laser Direct Structuring (LDS) on the inner side of the temple with a substrate made of polycarbonate (PC). The substrate thickness is 2.7 mm, the dielectric constant of polycarbonate is 2.85, and the dielectric loss tangent is 0.0092. The outside of the PC temples uses a sputtering coating process to ensure that the antenna’s metal ground and reserve slots have a coupling effect.
It can be seen from
Figure 1a that the glasses proposed in this paper refer to the currently popular plastic glasses, and the overall size is 155 mm × 145 mm × 50 mm. The left temple is equipped with antenna 1 and antenna 2, and the right temple is equipped with antenna 3 and antenna 4. The left leg antenna and the right leg antenna have a symmetrical structure.
Figure 1b is a detailed size figure of a single temple antenna. For the size code in the figure, please refer to
Table 1. The slot antenna occupies an area of 50 mm × 9 mm × 2.7 mm on the temple. The slot extends from the outside of the temple top, the length of the SL is 5.5 mm, and the width of the SW is 2 mm. The inverted-F antenna feeds from the ground side at 6 mm, and there is a 1 pF capacitor in series in the middle of the antenna. The length L of the antenna is 6 mm, and it reaches the ground through the Via hole. Therefore, the four antennas installed on the plastic glasses are not obtrusive and can meet the requirements of the metal frame of the smart wearable device.
2.1. Slot Antenna Simulation and Analysis
The antenna design steps proposed in this paper are shown in
Figure 2. In
Figure 2a, an inverted-F antenna that can be coupled to the slot is shown, which is grounded through a Via hole with a diameter of 1 mm. The ground plane is a metal copper layer covering the outer, top, and bottom sides of the glasses, and, according to the simulation results, slot holes are present on the outside grounding surface. Because the temple area is large, as
Figure 2b shows, the eyewear device has another symmetrical antenna at a distance of 18 mm from the inverted-F antenna.
Figure 2c shows two symmetrical inverted-F antennas with series capacitors, allowing the antenna to generate the resonance frequency of the target operating frequency band and, at the same time, enhance the isolation between the two antennas. Isolation performance is essential for MIMO antennas.
Next, the simulation software High-Frequency Structure Simulator (HFSS) version 2021R1 is used. First, we simulate and analyze the capacitance change, and then simulate and compare the length and width of the slot. The simulation results in
Figure 3a show that when the antenna is as in
Figure 2a, without series capacitors, the resonance frequency is generated by the entire slot antenna on 4.6 GHz and 6.7 GHz. However, the simulation results cannot cover the Wi-Fi 6e frequency band completely because the overall working frequency band cannot be continuous. Thus, we try to connect the inverted-F antenna in series with capacitive elements and adjust the capacitance value to change the resonance frequency of the slot antenna. When C1 = 0.5 pF, the working bandwidth cannot cover Wi-Fi 5G and Wi-Fi 6e. When C1 = 1 pF, the resonant points of the slot antenna can be obtained at 5.3 GHz and 6.6 GHz, and the working bandwidth can cover the entire Wi-Fi 5G and Wi-Fi 6e.
Figure 3b presents a simulation of the presence or absence of a series capacitor. It is found that the series capacitor can improve the isolation between the two antennas, and the S21 is lower than −10 dB.
In addition, we also simulate the change of slot size, and the result is shown in
Figure 4a. When the slot length SL is 4.5 mm, from the reflection coefficient |S11|≤ −10 dB, it can be seen that the resonance frequency will move to the high-frequency direction at 5.3 GHz to 6.6 GHz, and the resonance intensity will be weakened. When the slot length SL is 6.5 mm, the resonance frequency of 6.6 GHz will move to the low-frequency direction, and the working bandwidth will also be reduced.
Figure 4b shows that when the slot width SW is 1 mm, the resonance frequency will move to a low frequency at 5.3 GHz. When the slot width is 3 mm, the resonance frequency of 5.3 GHz will move to 6 GHz, and the overall operating frequency band will be weakened. In order to achieve the expected working frequency band and resonance strength, the proposed antenna SL is 5.5 mm, and the SW is 2 mm.
2.2. Surface Current Distributions
The operational mode of the slot antenna is based on the current entering from the feed point and exists in the entire inverted-F antenna. At the same time, this current will also be coupled around the slot and allow electromagnetic waves to radiate out of the slot. By adjusting the size of the slot, the target resonance frequency can be within the expected range. The surface current simulation results are shown in
Figure 5. When the current enters from the feed point, the proposed antenna will exhibit current coupling on the slot at the expected working frequency band, and it can be found that the working resonance frequency is 5.3 GHz and 6.6 GHz, and the energy is concentrated around the slot on the outside of the temple. From the current energy distribution, it is known that there is almost no current energy distribution between the two antennas, so the symmetrical antenna can provide good isolation.
3. SAR Simulation and Analysis
The human body is a high-loss material for the antenna. Therefore, the proposed antenna needs to be hung on the human head model for simulation, and we then observe whether the antenna’s performance is affected, so that the proposed antenna is more likely to be used in daily life.
Figure 6 shows the use of HFSS to simulate the Wi-Fi 5G and Wi-Fi 6e eyewear antenna system, which is placed on a human head model.
Next, we discuss the changes in reflection coefficient and isolation when the proposed antenna is close to the head. It can be seen from
Figure 6 that antenna 1 is closer to the head, and antenna 2 is farther from the head.
Figure 7 shows the simulation by placing the glasses on the head. However, the proposed antenna is symmetrical, so only antenna 1 and antenna 2 are simulated.
Figure 7a shows that when antenna 1 is at the head position, the working bandwidth is shortened due to the influence of the human body, and the reflection coefficient of antenna 2 is not significantly different between the head and the free space. Wireless products on the market can be accepted if the reflection coefficient is lower than −6 dB [
24,
25,
26], and when the proposed antenna worn on the head that the S-parameter is lower than −6 dB. Therefore, it matches the CTIA specification standard.
Figure 7b shows the isolation between antenna 1 and antenna 2, and the isolation is almost lower than −10 dB when hung on the head or in free space.
Smart wearable devices are the electronic products closest to the human body; these electronic products will transmit wireless communication through antennas, and electromagnetic radiation will definitely be generated during the transmission. Therefore, laws and regulations of various countries all have Specific Absorption Rate (SAR) specifications, which are mainly used to limit the electromagnetic radiation absorption caused by electronic products to the human body. For example, the FCC safety limit is 1 g SAR 1.6W/kg, and the European CE safety limit is 10 g SAR 2 W/kg. The SAR calculation method is the radiant power energy absorbed by a unit volume in a specific time, as shown in the following equation [
22]:
Antenna 1 and antenna 3 are closest to the human head in the proposed 4 × 4 MIMO slot antenna system, and the antenna structure is symmetrical, so only the SAR value of antenna 1 is simulated, and the SAR simulation software uses Sim4Life to operate. As shown in
Figure 8, when antenna 1 is 10 mm away from the head, the input power from the feed point is 0.1 W (20 dBm), and the frequency at 5.3 GHz and 6.6 GHz to calculate the values of 1 g SAR and 10 g SAR. According to the simulation results, the 1 g SAR and 10 g SAR of antenna 1 at 5.3 GHz are 1.39 W/kg and 0.722 W/kg, respectively, and the 1 g SAR and 10 g SAR at 6.6 GHz are 0.938 W/kg and 0.467 W/kg, respectively. Thus, the above SAR values are all lower than the certification limit.
According to the FCC’s regulatory test requirements, when the wearable device supports the frequency band above 6 GHz, the power density (PD) needs to be measured. PD test frequency is selected which the frequency point has the worst SAR value, and PD safety limit value is
. The equation is as follows [
27]:
Figure 9 shows antenna 1 when the input power from the feed point is 0.1 W (20 dBm), and the frequency is 6.6 GHz to calculate the PD value. According to the simulation results, the PD of antenna 1 at 6.6 GHz is
, which is lower than the limit of
.
4. Experimental Characterization
The actual work of the proposed 4 × 4 MIMO eyewear antenna has been completed, as shown in
Figure 10. According to the above simulation results, the inverted-F antenna on the inside of the temples needs to reserve a block for soldering series capacitors. Unfortunately, the antenna substrate is made of PC (PC’s melting point is 220 °C), which cannot withstand general soldering operations. Therefore, we use low-temperature soldering to prevent abnormal antenna performance due to the deformation of the temples.
Figure 10a shows a photo of the 4 × 4 MIMO plastic glasses.
Figure 10b shows a ground plane of the sputtered copper layer with slots on the outside of the temple.
Figure 10c shows an inverted-F antenna created by the LDS process on the inside of the temple.
4.1. S-Parameter Analysis
Because the proposed glasses’ antenna substrate is thick and the material is plastic with a low melting point, it is not suitable to use a copper pipe or SMA connector for measurement. Therefore, we use a coaxial cable with low-temperature soldering for measurement. The vector network analyzer model is Agilent E5071C, and we use the SOLT method to calibrate before the measurement, but deviation is present due to soldering and the inability to calibrate the coaxial cable. Therefore, the S-parameter measurement setup in free space is shown in
Figure 11a, and the glasses are worn on the human head to measure the S-parameters, as shown in
Figure 11b.
Figure 12a compares the S-parameter measurement and simulation of the single temple antenna 1. Due to the soldering and fabrication tolerances, frequency resonance may be weakened, but the measurement result is very similar to the simulation.
Figure 12b compares the measurement and simulation of the isolation between antenna 1 and antenna 2. The isolation between the measurement and simulation can be lower than −10 dB, complying with the MIMO antenna system’s basic specifications.
Figure 12c is the S-parameter measurement of four antennas. It is found that the effective working frequency bands of the four antennas are all in line with expectations. However, the reflection coefficient of antenna 4 is different from those of the other antennas. This deviation may be due to the soldering and fabrication tolerances.
The proposed antenna is designed on the glasses device, so it is necessary to measure the glasses’ S-parameter on the human head. Because the proposed antenna is a symmetric antenna, we use the left-side temple with antenna 1 and antenna 2 to measure the S-parameter.
Figure 13a shows the reflection coefficient measurement and simulation of antenna 1 and antenna 2. The simulation and measurement results are very similar. For antenna 2, simulation and measurement both move towards low frequencies.
Figure 13b shows the isolation result of antenna 1 and antenna 2. Both the simulation and measurement yield values lower than −10 dB, and the trend is consistent.
4.2. Radiation Pattern
From the results in
Figure 12c, it can be seen that the resonance modes of the four antennas are similar. Therefore, antenna 1 and antenna 2 are used for the following far-field test in this paper. The measurement field used this time is a standard far-field chamber, the network analyzer is the model Anritsu MS46524B, and the measurement frequency band of the horn antenna in the chamber is 0.1–8 GHz.
Figure 14 shows a photo of the test environment of antenna 1 in the far-field chamber, and the XYZ axis of the simulation software corresponds to the XYZ axis of the chamber for elevation.
The proposed glasses’ antenna works in linear polarization. In a specific receiving range, it will have better signal reception than a circularly polarized antenna. Currently, linearly polarized antennas are widely used in wireless communication products.
Figure 15 and
Figure 16 show the 2D gain field patterns of the simulated and measured eyewear antenna in the XY plane, the XZ plane, and the YZ plane. From
Figure 15 and
Figure 16, it can be seen that the simulated and measured radiation modes have the same trend when antenna 1 and antenna 2 are at the working frequency of 5.1 GHz and 6.8 GHz.
4.3. Antenna Gain, Efficiency, and ECC
The gain and efficiency of antenna 1 can be seen in
Figure 17a,b. The working frequency of antenna 1 can reach 4.3 dBi peak gain and 85.69% antenna efficiency in free space at 5.14 GHz and reach 3.3 dBi and 82.78% antenna efficiency in free space at 6.8 GHz.
When the antenna belongs to the MIMO system, the Envelope Correlation Coefficient (ECC) value is usually used to judge whether the antenna’s independence is good. The coupling effect between two antennas is poor when the ECC value is lower, and less of the transmission rate will be affected. The internationally recognized ECC limit value is 0.5. The ECC values of the two antennas can be calculated using the S-parameter equation as follows [
16]:
Another ECC calculation method is to use the antenna radiation direction calculation. The ECC value equation of the two antennas is as follows [
17]:
In the MIMO antenna system, when port 1 is excited and other ports are connected to a 50-ohm load, the far-field radiation direction generated by antenna 1 can be represented by . When port 2 is excited, the far-field radiation direction generated by antenna 2 can be represented by .
Figure 18 shows the ECC measurement and simulation comparison of antenna 1 and antenna 2 on a single temple. Again, it can be seen that in the effective working frequency band, the measured and simulated ECC values do not exceed 0.05, and the antenna’s independence is good.
Table 2 offers a comparison between the proposed antenna and other eyewear antennas. It can be seen that the reference antennas [
1,
3,
14] only support Wi-Fi 2.4 G, and the antenna efficiency is not good. For example, in [
3], the antenna efficiency is only 10.7%. The application of 60GHz eyewear antenna is mentioned in references [
4] and [
28]. Although references [
4] and [
28] have high antenna gain, but the complex design of the array antenna makes it difficult to realize the MIMO system on the glasses. After comparing the references of LTE frequency bands that references [
20] and [
29] support multiple LTE frequency bands, but the antenna gain is not good [
20] and the operating frequency is not continuous [
29]. Reference [
30] used an eyewear frame antenna and supported IoT 5.8 G, but it did not possess a MIMO function. In summary, no antenna design supports Wi-Fi 6e in the current references. However, our proposed eyewear antenna has a wide working bandwidth, high antenna efficiency, high antenna gain, supports 4 × 4 MIMO, and can be applied to the Wi-Fi 5G and Wi-Fi 6e bands.
5. Conclusions
This paper proposes a method that allows standard plastic glasses in daily life to undergo a unique antenna manufacturing process, which can also be applied to Wi-Fi 5G and Wi-Fi 6e communication bands. Mainly relying on the antenna LDS process, four symmetrical slot antennas are carved on the plastic temples so that the plastic glasses can also achieve the 4 × 4 MIMO transmission effect. Furthermore, such an antenna configuration can make full use of the glasses’ space to receive the signal on the left and right without blind spots. At the end of this study, a physical antenna was successfully produced, and the actual measurement results show that the efficiency and gain of the antenna are good, meaning that the smart plastic glasses have a high probability of being used in Wi-Fi 5G and Wi-Fi 6e application scenarios in the future.