1. Introduction
People die and get injured in traffic accidents all over the world. It is mandatory for all vehicles to get information about traffic and road conditions to avoid accidents [
1]. To cater to this issue, an effective and efficient transport management system is required to minimize road accidents and congestion, as specified in [
2]. It is mentioned in [
3] that 60 percent of accidents can be avoided if warning messages are delivered to drivers before accidents. Hence, scientists have introduced vehicular ad-hoc networks (VANETs), which turn every vehicle into a wireless node that can communicate with other vehicles. The VANET is a special class of mobile ad-hoc network (MANET) formed by vehicles equipped with wireless gadgets. VANET communication takes place between vehicle to vehicle (V2V) mode and vehicle to roadside unit (RSU), forming an intelligent transport system as shown in
Figure 1. The Wireless Access Vehicular Environment (WAVE) was adopted from 802.11a and is used in intelligent transportation systems (ITS). In VANET, vehicles communicate with each other to share information required for safety, comfort, entertainment and low latency purposes.
In
Table 1, VANET communication technologies are summarized. Bluetooth, RFID and GPS are simplex types of communication. The other technologies are duplex. The range of Bluetooth is minimal, i.e., approximately 10 m. 2G/3G/4G/5G and GPS provide global coverage.
The demand for communication in VANET with high data rates has dramatically increased in recent years. This requires the utilization of limited resources such as power and bandwidth as efficiently as possible to support the massive communication demand in VANET. Currently, for wireless communication, millimeter-wave (mmWave) massive MIMO has been identified as the most promising technology for vehicular communication [
4] The millimeter-wave band comprises a range from 30 to 300 GHz, which means a wavelength in between 1 and 10 mm. Millimeter-wave has lots of benefits and advantages, due to which it is suitable for 5G communication, cellular communication and other wireless communication. High accuracy, small antenna size, smaller cell and power efficiency are some advantages of millimeter wave.
Due to the high mobility of vehicular nodes and the multipath fading, reliability, throughput and accuracy are the important aspects of VANET millimeter-wave communication. In millimeter-wave communication, the signal distorts and attenuates more due to the short wavelength. Pathloss is very high because of high career frequency. Further, it is more susceptible to rain and atmospheric attenuation. In past research, MIMO, space-time block coding (STBC) and cooperative MIMO have been tested to achieve reliability and a high data rate. MIMO using ASTBC along with error control coding has not been explored yet. For vehicular communication, a manipulable architecture is needful which provides us with high reliability and a lower bit error rate.
The main contribution of our work is the derivation of exact closed-form expressions to calculate the BER using ASTBC and BCH coding. Our derived expressions can be utilized in BER computations, in contrast to SNR and code rate. Further, SNR can be computed for two blockers, which ultimately gives us an error probability for two blockers. The results show that our proposed BER outperforms the traditional ASTBC BER equation. Both numerical and simulation results verify each other, and hence provide a basic point of reference for further exploration. A significant reduction in computational complexity was obtained when evaluating system performance using our derived expressions.
The organization of the paper is as follows. Related work is explained in
Section 2.
Section 3 defines the ASTBC in which signal transmission using two transceivers is described.
Section 4 describes the system model in which the pathloss of our model is computed. The closed-form approximations of BER for BCH in Rayleigh fading and BCH-concatenated ASTBC coding are derived.
Section 5 contains results and discussion. Last comes the conclusion in
Section 6.
2. Related Work
Currently, Dedicated Short-Range Communication (DSRC) is a VANET communication protocol. The coverage range of DSRC is about 1 km, with achievable data rates in the order of 2–6 Mbps. The massive data rate that is expected to be required by the next generation of automotive applications cannot be achieved using these technologies [
5]. A multi-band orthogonal frequency division multiplexing (MB-OFDM)-based ultra-wideband technique is used to transmit large data blocks in VANET [
6]. Various studies have been carried out regarding bit error analysis. BER was studied on mobile station MS velocity variations using 802.11p. Results showed that there is very little impact from velocity variations on bit error performance. However, when the data frame length or relative speed increases, performance is affected. Millimeter-wave is a good solution for high-speed Internet access. The power delay profile (PDP) of the wireless intra-vehicular channel was derived from 1000 data sets. A tapped-delay-line (TDL) was derived based on the proposed PDP profile. The TDL model was used for a bit error study of millimeter-wave by varying data rates and link length. Since millimeter waves cannot penetrate walls, a relay device is required to redirect signals [
7]. In [
8] bit error rate probability was evaluated for interference in a multi-hop millimeter-wave system. To achieve reliability and continuity in vehicular communication, an adaptive transmission mechanism was proposed. The mechanism should adjust the data rate according to the number of connected vehicles [
9].
The current communication technologies cannot meet the high data rate requirements in vehicular communication. Therefore, a radio on fiber architecture was proposed [
10]. To achieve a high data rate, a higher modulation order is used in radio on fiber architecture. An adaptive modulation mechanism was proposed [
11]. An architecture of VANET using multi-gigabit communication was proposed in [
12]. In the proposed architecture, i.e., the Giga-V2V (GiV2V) network, millimeter-wave is used to deliver high-quality video and sensor data of smart and self-driving cars. A few years back, only wireless access in the vehicular environment (WAVE)/IEEE 802.11p was available for V2V communication. New release 14 of long term evolution (LTE) and the arrival of 5G opened up new challenging possibilities. Due to the widespread deployment of the cellular systems and low latency, LTE V2V supplanted WAVE/IEEE 802.11p. However, LTE V2V is in the preliminary phase. There are certain drawbacks in current communication technologies. In WAVE/IEEE 802.11p, performance degrades with an increase in channel load. In high density areas, collisions occur, due to which network performance degrades in terms of throughput and latency [
13].
3. Alamouti Code (Transmitter Diversity)
This section gives an overview of ASTBC. In ASTBC, two transmitters and two receivers are used. Consider a vehicular node i equipped with two transmitting antennas
and
, and node j equipped with two receiving antennas
and
. The channel between
and
is denoted by
; that between
and
is denoted by
.
represents the channel between
and
and
represents the channel between
and
, as shown in
Figure 2.
The two received signals in two adjacent symbol intervals can be written as
where
n1,
n2,
n3 and
n4 are complex thermal noise and interference. The receiver
rx0 receives two symbols
r0 and
r1 in time t and the receiver
rx1 receives two symbols
r2 and
r3 in time t + T.
The combiner combines signals and gives two O/P signals
y0 and
y1.
4. System Model
A vehicular network with N number of nodes is considered for modeling our propagation channel. d is the transmission range in meters.
Figure 3 depicts the simulation model in which node i is communicating with node j. Consider a scenario in which node i is approaching node j which is decelerating. Node j will send a warning message to node i. We have simulated the scenario and have compared our results with simulated BER in the Rayleigh channel. Our BER computational approach with node i and node j is described in the next subsections. The simulations were performed in Matlab, as Matlab is user-friendly, and developing computational code and plotting graphs is easy in Matlab.
The pathloss (PL) in db can be computed using expression [
14]
where
represents path loss exponent;
corresponds to a parameter for different numbers of blockers. The middle term in Equation (
1) represents atmospheric attenuation for 60 GHz. The simulation parameters are shown in
Table 2.
The received SNR
can be computed using expression (2).
where
Pt corresponds to transmit power,
Gtx represents transmitter array gain,
Grx represents receiver array gain,
Nt represents the number of transmitters,
Rc corresponds to code rate,
NF represents noise figure and NP corresponds to noise power which is computed using the expression below.
Simulation parameters of SNR are depicted in
Table 3.
These simulation parameters were used to compute the SNR of our model. In
Section 4.1 and
Section 4.2, the SNR is used in our closed-form expression derivation.
4.1. Bose–Chaudhuri–Hocquenghem (BCH) Coding in Rayleigh Fading on Node i
In this subsection, a closed-form expression for BCH coding in Rayleigh fading is derived. The probability of error of BCH coding in Rayleigh fading on node i can be written as
where
and,
Substituting expression (4) and expression (5) into expression (3) yields,
In [
15] (Equations (A.35) and (A.36), pp. 114, 134)
Using this substitution,
where
Substituting the above expression in expression (6) yields
Converting
Q function into an error function gives [
16] (Equation (2.55), p. 56)
where
Substituting x in above expression gives us
Substituting the above expression into Equation (
7) gives
Applying integration by parts gives
In [
17] (Equation (3), p. 4)
where
Therefore,
Plugging expression (10) in expression (9) gives us
Applying differentiation gives
In [
18] (Equation (3.310), p. 334):
Plugging the above expression in Equation (
12) yields
Hence, the closed form expression of BCH probability of error in terms of mmWave Rayleigh fading can be written as
The bit error rate was computed for different values of the code rate, i.e., (127,64), (127,36) and (255,251) using Equation (
14).
4.2. BER in Concatenated ASTBC and BCH on Node j
In this section the closed-form expression of BER of ASTBC using BCH coding is derived. The probability of error on Node j using ASTBC and BCH can be written as
where
PBCH is given in expression (4). The probability of error in ASTBC (
PASTBC) can be written as
Plugging above expression and expression (4) in expression (15) yields
Using the substitution used in previous section where
in expression (16) can be written as
Converting Q function into the error function yields
By using the relation described in expression (10), i.e.,
expression (18) can be written as
Expression (19) gives us a new tractable closed-form expression of BCH in ASTBC.
5. Results and Discussion
In this section results of the pathloss model and BER closed-form expressions are described.
Figure 4 displays our pathloss for two vehicles (obstacles). It can be remarked with more obstacles, i.e., n = 0, 1 and 2, pathloss also increased. Further, when increasing distance between tx and rx, pathloss also rose. When the number of obstacles was 2, pathloss was −135 dB at 30 m.
Figure 5 shows the results of BCH in the Rayleigh fading using equation 14. The results are compared with the AWGN channel and the simulated BER in the Rayleigh channel. From
Figure 5 it can be noticed that the BER was getting low when EbNo was increasing. The former’s code rate (127,36) was superior. In
Figure 6 the results using the conventional ASTBC equation and our proposed expression, i.e., expression 19 (BER using ASTBC with BCH coding), are shown. The BER of ASTBC with BCH coding was minimum in contrast with the BER without BCH coding. The simulated BER in the Rayleigh channel and the BER without BCH coding were similar. The former’s code rate (127,36) was superior.
Table 4 shows that our BER computation approaches outmatched other techniques.
6. Conclusions
In this manuscript, a tractable channel model for millimeter-wave communication in VANET was presented. The main contribution of this research was to provide a statistical and analytical framework to evaluate the performance of VANET using millimeter-wave with channel coding, i.e., BCH and RS. The pathloss was computed for three vehicles. The pathloss was getting high in two cases—first the number of vehicles increased; secondly, the distance between tx and rx increased.
Using our derived closed-form expressions of BER, we simulated the BER of our proposed BCH in Rayleigh fading and the BER of concatenated ASTBC and BCH coding. The results showed that the BER using concatenated ASTBC and BCH coding was the most depleted. The result of the proposed approximation, i.e., expression 19, was compared with the orthodox BER ASTBC expression. The results showed that the BER using BCH-coded ASTBC was less than the BER using the orthodox expression for BER. The results were compared using different code rates. The BER using code rate 12,732 was the smallest.
The derived expressions were validated and verified for scenarios of practical interest and complemented by the simulation model. Furthermore, a significant reduction in the computational burden was obtained.
Author Contributions
Conceptualization, A.A. and H.R.; methodology, A.A.; validation, H.R. and M.L.; investigation, H.R.; writing—original draft preparation, A.A.; writing—review and editing, H.R. and M.L.; supervision, H.R. All authors have read and agreed to the published version of the manuscript.
Funding
This research received no external funding.
Conflicts of Interest
The authors declare that they have no conflict of interest.
Abbreviations
The following abbreviations are used in this manuscript:
VANET | Vehicular Ad-Hoc Network |
OBU | On-Board Unit |
RSU | Roadside Unit |
BCH | Bose–Chaudhuri–Hocquenghem |
ASTBC | Alamouti Space-Time Block Coding |
BER | Bit Error Rate |
ITS | Intelligent Transportation Systems |
STBC | Space-Time Block Coding |
DSRC | Dedicated Short-Range Communication |
MB-OFDM | Multi-Band Orthogonal Frequency Division Multiplexing |
PDP | Power Delay Profile |
TDL | Tapped-Delay-Line |
LTE | Long Term Evolution |
References
- Hassan, H.S.; Saad, T.H. Improving Communication Reliability in Vehicular Networks Using Diversity Techniques. J. Comput. Theor. Nanosci. 2019, 16, 1–6. [Google Scholar] [CrossRef]
- Low, J.W.; Joanne, M.-Y.L. Identifying Transmission Opportunity Through Transmission Power and Bit Rate for Improved VANET Efficiency. Mob. Netw. Appl. 2019, 24, 1630–1638. [Google Scholar] [CrossRef]
- Fan, B.; Krishnan, H. Reliability Analysis of DSRC Wireless Communication for Vehicle Safety Applications. IEEE Intell. Transport Syst. Conf. 2006, 355–362. [Google Scholar] [CrossRef]
- Yi, Z.; Zou, W. A Novel NE-DFT Channel Estimation Scheme for Millimeter-Wave Massive MIMO Vehicular Communications. IEEE Access. 2020, 4, 1–12. [Google Scholar] [CrossRef]
- Syed, A.A.S.; Ejaz, A.; Muhammad, I.; Sherali, Z. 5G for Vehicular Communications. IEEE Commun. Mag. 2018, 111–117. [Google Scholar] [CrossRef]
- Yin, X.; Liu, J.; Zeng, B.; He, W.; Xiong, X.; Zhang, H. A Novel Scheme for Large-Size Data Block Transmission in vehicular Ad hoc Networks: Architecture, Challenges, and Discussions. IEEE Mag. 2019, 91924–91939. [Google Scholar] [CrossRef]
- Aniruddha, C.; Aniq ur Rahman, U.G. 60-GHz Millimeter-Wave Propagation Inside Bus: Measurement, Modeling, Simulation, and Performance Analysis. IEEE Access 2019, 7, 97815–97826. [Google Scholar] [CrossRef]
- Ali, C.; Kimmo, K.; Mohamed-Slim, A.; Ilangko, B. On Bit Error Probability and Power Optimization in Multihop Millimeter-Wave Relay Systems. IEEE Access 2018, 6, 1–12. [Google Scholar] [CrossRef]
- Wei, Y.; Chen, J.; Hwang, S.-H. Adjacent Vehicle Number-Triggered Adaptive Transmission for V2V Communications. Sensors 2018, 3, 755. [Google Scholar] [CrossRef] [Green Version]
- Rafeeun, N.B. Efficient M-QAM Digital Radio Over Fiber system for Vehicular Ad- Hoc Network, International Conference on Robotics. Electr. Signal Process. Tech. 2019. [Google Scholar] [CrossRef]
- Aisyah, N.; Titiek, S.S. Performance Analysis of Vehicle-to-Vehicle Communication with Adaptive Modulation, Electric power, electronics, communication and informatics seminar (EECCIS). IEEE Access 2018, 187–191. [Google Scholar] [CrossRef]
- Wooseong, K. MC-GiV2V: Multichannel Allocation in mmWave-Based Vehicular ad Hoc Networks. Wirel. Commun. Mob. Comput. Hindawi 2018, 2018. [Google Scholar] [CrossRef]
- Masini, B.M.B.; Natalizio, R. Access for Future Vehicular Networks in Vehicular Technology. In Proceedings of the IEEE 86th Vehicular Technology Conference (VTC-Fall), Toronto, ON, Canada, 24–27 September 2017; pp. 1–7. [Google Scholar] [CrossRef] [Green Version]
- Vutha, V.; Takayuki, S.; Gaurav, B.; Robert, W.H., Jr. Millimeter-Wave Vehicular Communications: A Survey, Foundations and Trends in Networking; Now Publishers Inc.: Hanover, MA, USA, 2015; Volume 10, pp. 78–79. [Google Scholar] [CrossRef]
- Simon, M.K. Probability Distributions Involving Gaussian Random Variables: A Handbook for Engineers and Scientists; Springer Science and Business Media: Berlin/Heidelberg, Germany, 2007; pp. 114–134. ISBN 978-1-4020-7058-7. [Google Scholar]
- Andrea, G. A Wireless Communication; Cambridge University Press: Cambridge, UK, 2015; p. 56. [Google Scholar]
- Ng, E.W.; Geller, M. A table of Integrals of the Error Functions. J. Res. Natl. Bur. Stand. B 1969, 73, 4. [Google Scholar] [CrossRef]
- Gradshteyn, I.S.; Ryzhik, I.M. Table of Integrals, Series, and Products; Elsevier: Amsterdam, The Netherlands, 1956; p. 334. [Google Scholar]
- Roy, R.K.; Roy, T.K. BER Analysis of MIMO-OFDM System Using Alamouti STBC and MRC Diversity Scheme Over Rayleigh Multipath Channel. Glob. J. Res. Eng. 2013, 13, 5–13. [Google Scholar]
- Al-Barrak, A.; Al-Khalil, A.B. Impact of Alamouti Space—Time Block Coding on the Performance of Vehicle-to-Vehicle Communication. Int. Conf. Adv. Sci. Eng. 2018, 11, 105–109. [Google Scholar]
- Raad, H.T.; Muntadher, S.A. Improvement the Performance of MIMO Channel Employing Concatenation (BCH –STBC) Codes. IOP Conf. Ser. Mater. Sci. Eng. 2020. [Google Scholar] [CrossRef]
- Ntaganda, J.; Ntagwirumugara, E.; Musabe, R. Bit Error Rate Mitigation in VANETs Using FFH-OFDM Pre-Coding Approach. Int. Conf. Intell. Innov. Comput. Appl. 2018, 1–8. [Google Scholar] [CrossRef]
| Publisher’s Note: MDPI stays neutral with regard to jurisdictional claims in published maps and institutional affiliations. |
© 2021 by the authors. Licensee MDPI, Basel, Switzerland. This article is an open access article distributed under the terms and conditions of the Creative Commons Attribution (CC BY) license (https://creativecommons.org/licenses/by/4.0/).