1. Introduction
Plates are often used in engineering fields, such as in manufacturing of electronic, optical, and mechanical devices, as well as the military, ship, aerospace, civil, and automotive industries. The mathematical model of the deformation problem of elastoplastic plates is defined by a boundary value problem for biharmonic equations. In the literature, researchers have developed various approaches and methods for the purpose of finding an exact or a numerical solution of these biharmonic equations with certain boundary conditions. In the deformation problem of rectangular elastic plates, boundary conditions may generally be given in a total 21 different possible combinations of simply supported, clamped, or free boundary conditions along each plate edge [
1]. Several studies have been carried out to obtain the plate equation from the equilibrium equation of a deformed three-dimensional rigid body. The general three-dimensional elasticity solutions for the deformation problem of elastic plates were studied in detail by various researchers [
2,
3,
4,
5]. The problem of bending of a rectangular plate given by symmetrical boundary conditions along its edges under a load was also investigated [
6,
7,
8]. Using the monotone potential operator theory, Hasanov developed the variational approach theory for nonlinear biharmonic equations related to bending of elastoplastic plates [
9,
10]. There are various research results on multilayered (sandwich) plates based on different fields of application areas. The plate theory for multilayered and the sandwich plates was developed in different studies [
11,
12,
13,
14,
15], and the capacity and deficiencies of the theory were investigated. Most publications deal with composite materials. There are a limited number of studies related to plates with internal hinges [
16,
17,
18,
19,
20].
This study examined the deformation problem of a plate system (formed side-by-side) composed of inhomogeneous elastoplastic plates with different properties. In order to find a numerical solution of the problem, the transmission conditions on the common border and their numerical expressions were obtained.
In
Section 2, the problem formulation was given. In
Section 3, the transmission conditions were obtained at the common boundary in order that plates in the system composed of inhomogeneous elasto-plastic plates with different properties move together. The finite difference equations of both the equilibrium equation of the plates and transmission conditions were obtained by using the functional approximation method in
Section 4. In
Section 5, the test functions were defined to check the accuracy of the prepared computer program, and then error analyses of the numerical solutions were given. In
Section 6, the bending of the plates system was examined when different boundary conditions were given on the boundaries of the system by using the prepared computer program. According to the change of
and
in the plate system, the effect of elasticity modulus
on maximal bending was analyzed.
2. Problem Formulation
Let us consider a plate system (formed side-by-side) composed of inhomogeneous elastoplastic plates with different properties that filled
regions, where
is the number of plates that formed the system and
. The problem of bending of the system may be written mathematically with the discontinuous coefficient von Karman equation, as follows [
21]:
where
is the bending of the system corresponding to
forces applied vertically onto the plate, and
values are the cylindrical stiffness coefficients of the plates of the system. Moreover,
and
values are the Young’s modulus and Poisson constants of the plates, respectively. The thicknesses of all plates composed of the system are the same and equal to
.
Based on the case of plate boundaries, the boundary conditions depending on the physical meanings for the equilibrium equation are generally classified in two manners: clamped boundary condition and simply supported boundary condition , where is the unit outward normal to the boundary . Since the plates in the system have different cylindrical stiffness coefficients, the coefficients of Equation (1) lead to discontinuity at the common boundaries of the system. When such problems are solved based on fields of application, it is necessary to show the transmission conditions which depend on the shape of the junction on the common boundaries of the plates , as well as specific boundary conditions that correspond to the problem.
3. Obtaining the Transmission Conditions
For instance, let us consider
, i.e., two plates with different properties occupying the rectangular region
(
Figure 1).
In the case that the plates are connected through with a beam whose bending stiffness coefficients are
and torsional stiffness coefficients are
on the common boundary
, the potential energy of the plate system is [
21]
Here,
is the stiffness coefficient of the hinge of the connected plates, while
is the stiffness coefficient of support (anchorage provided by the hinge). For the loaded elastic body to reach equilibrium, the Gateaux derivative of the full potential energy of the plates must be equal to zero.
where
and the function
is in the same class as the function
. Thus, we obtain
After calculating the integrals in (3), the terms corresponding to the common boundary
of the plates are written down as follows:
Obtaining the transmission conditions on the common boundary
of the plates firstly involves writing down the terms corresponding to this edge where the coefficients of
expressions are equal to zero, and then the discontinuity of ω is also added on the common border, and the following transmission conditions are obtained:
Here, is known as the jump of at . Usually, based on the shape of the junction of the plates on the common boundary, there are different meanings of transmission conditions depending on different values of non-negative constants , and .
4. The Finite Difference Approximations of the Transmission Conditions
Let us define the mesh
sized
in the region
, where
,
are the uniform meshes on the axes
, respectively (also
are step widths of meshes,
are the number of points on the axes
, respectively). In order to obtain the finite difference equations that correspond to the problem described in a previous study [
21], let us use the functional approximation method. Considering the expressions of the transmission conditions (4)–(6) and
,
, we may show the finite difference approximation of the functional
as
Here,
are the finite difference approximations of the energy functions on meshes
. Additionally,
are the finite difference expressions of the collected terms that belong to the common boundary
. The expression
is obtained as follows:
where
,
denote the left-hand derivatives and
denote the right-hand derivatives of function
on the axes
, respectively. Defining the following coefficients,
we may rewrite
by using (8)–(10) as follows:
where the Dirac function is
The
that was obtained above is a multivariable function that depends on the variables
. Keeping this in consideration, if the derivative of the functional
with respect to
is computed and equated to zero, we can obtain the finite difference expression of Equation (1) as the following:
Using Equation (13), we obtain the finite difference approximations of the transmission conditions on the points of the common border and their neighbors, i.e.,
. Firstly, Equation (13) is turned into (14) for the points
:
For the points that belong to the common border
in
, the finite difference expressions of the transmission conditions are
Finally, we reach Equation (16) for the points
:
Thus, we obtain the finite difference approximations of the transmission conditions on as Equations (14)–(16).
5. Computer Simulations and Results
This section presents the error analyses of the numerical solutions for the purpose of checking the accuracy of the computer program that was prepared by using MATLAB. Let us take into account two different examples that correspond to the deformation problem of the plate system that fills the rectangular region, where . We may easily show that the following functions satisfy the simply supported boundary condition and the clamped condition on the boundaries of and the common borders , respectively as (a) , (b) .
The function is geometrically equivalent such that the plates are connected with an ideal hinge () on the common boundary points, and there is an absolute hard support () under the hinge. The function also corresponds to the bending on the common boundary in the case of . This means that the plates were composed by welding () and there is an absolute hard support () under the hinge.
The right sides of Equation (1) for functions
and
are, respectively, as follows:
where
.
Both examples are resolved in different-sized meshes
to investigate the effects of the change in the size of the mesh on the error of the numerical solution.
Table 1 shows the maximal bending
and the values of relative error. The relative error of the approximate solution that is obtained are
for
and
for
when using
. Examining the values in the table, it is seen that the results that are obtained are less than 1% of the relative errors in the mesh that is used and smaller-stepped meshes.
6. Numerical Experiments
This section examines the numerical solution examples for the bending problem with external force effects of the system composed of plates with different properties. Let us consider the plate system composed of two thin plates whose Young’s modulus are
,
, and Poisson’s constants are
,
, respectively. When the clamped condition is given on the boundaries of the system, the force
is applied at 21 points in total on the condition that there are nine points on both the middle of the left and right plates and three points on the common border
. In order to examine the effects of Young’s modulus on the bending of the system, we solve the problem for different boundary conditions and different transmission conditions when
, (i)
,
, (ii)
, and (iii)
,
.
Table 2 shows the results that are obtained.
means that the hinge can ideally move on the common boundary of the plate system, whereas
indicates the presence of support with finite hardness under the hinge. In a special case, the numerical solutions that are obtained for
are given in
Figure 2a–c. For comparison of the results, the cross sections at
are shown in
Figure 2d.
Figure 3 shows the cross sections of the numerical solutions obtained for the bending problem of the plate system at different
and
values.
The following tables show the values of the maximal bending that corresponds to the constant force of the computer experiments given above in the geometric interpretations. The results are presented in
Table 2 and
Table 3 for different values of
,
, respectively, when the clamped boundary conditions and the simply supported boundary conditions are given for the boundaries of the system. Furthermore, the values of
,
, and
shown in the tables below are the bending values that occurred on the left plate, the common border
, and the right plate, respectively.
7. Conclusions
This study obtained the transmission conditions on the common boundary in the biharmonic equation given by the discontinuous coefficient by using the functional approximation method, and analyzed the numerical results. The method that was used here may be used to find the numerical solution of problems expressed by mathematical models of differential equations with discontinuous coefficients. The same approach can be used to derive the sizes and mechanical properties of the plates forming the system.