1. Introduction
Foxtail millet (
Setaria italica, abbreviated as FM) is one of the world’s oldest cultivated crops. It originated from China and, because of its excellent drought resistance, high tolerance to poor soil, and good nutrient value, it is now planted in India, Japan, Australia, North Africa, and South America [
1]. FM possesses effective medical and nutritional qualities, including the ability to inhibit oxidants, cancer, and inflammation [
2]. FM bran (FMB) is a by-product of FM processing and is produced after shelling [
3]. It is rich in lipids, starch, proteins, vitamins, and minerals [
4,
5] and it is typically not fully utilized. Its current uses in China are mostly as animal feed and agricultural fertilizer. However, FMB should be viewed as a valuable resource that can be developed and utilized to produce value-added products. FMB utilization in this manner not only would effectively use an agricultural waste product but also might enrich farmers and improve their standard of living. For example, FMB may be a good source of linoleic acid, a potentially bioactive component.
Ethyl linoleate (ELA) is obtained by esterification of linoleic acid and ethanol, catalyzed by sulfuric acid. ELA has many physiological functions, such as enhancing immunity, reducing cholesterol and blood lipid levels [
6], and mediating and controlling metabolism [
7]. It is also the raw material for producing a drug that is highly effective at preventing and treating chronic diseases such as cerebral thrombosis and atherosclerosis [
6]. It is also an effective treatment for mild to moderate acne, with effects on both inflammatory and non-inflammatory acne lesions [
8]. In addition, ELA could also be added to health food [
9], because of its function of reducing cholesterol and blood lipid levels. Hutsell, TC and Quackenbush, FW. suggest that subjects that received a fat-free diet with 2% of ELA showed lower plasma and hepatic cholesterol levels and more complete aortic protection than control subjects [
10]. Therefore, ELA can be used as food for special medical purposes to help reduce plasma and hepatic cholesterol levels. Therefore, ELA has broad market applications in the pharmaceutical, cosmetic, health food, and other industries. It is thus a product that increases the value of FMB.
Several methods can be used to obtain polyunsaturated fatty acids (PUFA) from FMB; these include controlled low-temperature crystallization, winterization, urea complexation (UC), molecular distillation (MD), silver ion complexation, liquid chromatography, and extraction with supercritical carbon dioxide [
11]. However, those methods are slow, inefficient, may generate undesirable by-products, and are generally difficult to scale up for industrial production [
12].
The simplest and most efficient technique to obtain PUFAs is UC [
13], a method that separates mixtures of fatty acids according to their degree of unsaturation [
14]. Unsaturated fatty acids are non-linear molecules because of the presence of multiple double bonds, whereas saturated and monounsaturated fatty acids are almost linear, with a structure that can be easily trapped in the cavity of a urea complex [
15]. The main advantage of UC is the extreme stability of the crystal complex, which obviates the need for filtration at the very low temperatures required for solvent crystallization of fatty acids [
13].
MD is a gentle distillation method suitable for separating and purifying high-molecular-weight, thermally unstable materials and liquids at low vapor pressure and low temperature [
16]. In the MD process, vapor molecules escape from the evaporator and are then captured in a condenser. Thus, it is necessary for vapor molecules to find a free path between the evaporator and the condenser. Material separation is achieved based on differences in the mean free path of a particle. Distillation occurs in a stationary state, where flows of two products are continuously generated; these consist of distillate cuts that are made of condensed molecules and the residue of MD, which is composed of non-evaporated molecules [
17]. This technique reduces the risk of oxidative damage and is thus a very useful technique in the purification of thermolabile substances [
15].
Many studies that used UC or MD to purify ELA focused on only one technique [
13]. Here, we used both UC and MD to purify ELA from FMB oil. We determined the optimum ratios of 95% ethanol-to-urea and urea-to-fatty acid and determined the optimum crystallization time and temperature to separate ELA from FMB oil by UC. ELA was purified by MD. Gas chromatography–mass spectrometry (GC–MS) was used to compare fatty acid compositions before and after purification aand determine the optimal purification processes for ELA.
2. Materials and Methods
2.1. Materials
FM (Setaria italica) was purchased from Ji’nan, Shandong Province, China, on 15 June 2020. Only ripe (the ear seeds were completely hardened and presented the color of the original species), undamaged seeds were used. The millet was shelled, and the millet bran was obtained after dehulling (dehusking), milling, and polishing. Dehulling was done using a stone abrasive dehuller for 30 min, and bran was separated from the grain by winnowing.
A standard mixture of 21 fatty acid ethyl esters (FAEEs) was purchased from Nu-Chek-Prep. Inc. (Elysian, MN, USA). Hexane (chromatographic-grade) was purchased from the Beijing Reagent Company (Beijing, China). Aqueous ethanol, anhydrous Na2SO4 (analytical reagent, 99.0%), KOH (purity: >98.0%), and HCl (36%, AR) were acquired from Tianjin Guangfu Chemical Reagent Company (Tianjin, China). Petroleum ether (boiling range: 30–60 °C) was an analytical-grade, pure reagent purchased from the chemical reagent Co., Ltd. of the Chinese medicine group. Water was deionized using a Milli-Q purification system (Millipore, Schwalbach/Ts, Germany). All other solvents and chemicals used were of analytical or GC grade.
2.2. Sub-Critical Fluid Extraction (SFE) of Bran Oil and Preparation of Mixed Fatty Acid Ethyl Esters (MFAEs)
A method previously used to extract bran oil and prepare MFAEs was used in this study, with slight modifications [
18]. Briefly, FMB oil was extracted using tetrane as a solvent. Single-factor and orthogonal experiments were used to optimize the extraction of FMB oil by SFE.
Fatty acid esters (FFAs) were obtained by esterifying FMB oil. A KOH solution was prepared by dissolving 56 g NaOH in 1 L of aqueous ethanol. A mixture containing 10 g of oil and 150 mL of 1N KOH–C2H5OH solution was heated at specified temperatures and times, and then the mixture was cooled to 20 °C. A solution of 15% NaCl was then added to the mixture. A solution of 20% hydrochloric acid was then added until the solution was at pH 2–3. Then, this mixture was put in a separatory funnel. Light petroleum was used for the extraction, for three times, and the extract was combined with the organic phase. The FFA-containing upper layer was dried with anhydrous sodium sulfate, and the solvent was evaporated in a vacuum rotary evaporator at 50 °C.
2.3. ELA Enrichment by UC
UC was performed following a previously described procedure with slight modifications [
18]. Briefly, the bran oil ethyl ester was mixed with different amounts of urea-saturated 95% aqueous ethanol and fluxed until a homogenous solution was obtained. The resulting mixture was refluxed until its appearance became clear. The solution was then cooled to 0–4 °C and held at this temperature overnight to allow for crystallization to occur. The resulting crystals were collected by filtration, and the filtrate was concentrated in vacuo. The resulting residue was treated with 0.1 N HCl. The acidified solution was then extracted thrice by petroleum ether. The extract was dried over anhydrous sodium sulfate and distilled to dryness in vacuo. The resulting ELA concentrate was then stored at −4 °C.
2.3.1. Single-Factor Test Design
Optimum 95% ethanol-to-urea ratio (
v/
w), urea-to-fatty acid ratio (
w/
w), crystallization temperature, and crystallization time based on the recovery and purity of ELA were determined using single-factor experiments. Variables and experimental levels for the single-factor tests were as follows: 95% ethanol-to-urea ratios (
v/
w) of 5:1, 10:1, 15:1, 20:1, and 25:1; urea-to-fatty acid ratios (
w/
w) of 1:1, 1:1.5, 1:2, 1:2.5, 1:3, 1:3.5, and 1:4; crystallization temperatures of −18, −15, −12, −9, −6, −3, 0, 3, and 6 °C; crystallization times of 3, 6, 9, 12, 15, 18, 21, 24, and 27 h. These parameters were established following a previous studies with slight modifications [
17].
2.3.2. Optimization of the Experimental Design
Single-factor experiments were used to evaluate the factors that influenced the results of ELA-containing liquid for further optimization. Purification conditions of ELA were optimized using a response surface Box–Behnken central composite design, using the purity of ELA as the response value. The coding of factors and levels of the response surface are shown in
Table 1.
2.4. Wiped Film-Short Path MD Equipment and Methodology
The apparatus used in this study consisted of the KDL 5 short path MD system [
19]. The schematic diagram for this equipment is shown in
Figure 1. The apparatus was constructed mostly from glass. The evaporator was heated using a jacket through which heated oil from an oil bath was circulated. The vacuum system included a diffusion (10
−3 mbar) and a mechanical (10
−2 mbar) pump. The speed of the roller wiper inside the evaporator ranged from 50 to 400 rpm. An external condenser and a cold trap were installed immediately downstream of the still. Condensable, low-molecular-weight compounds were collected in the cold trap upstream of the vacuum system, and the cold trap was filled with liquid nitrogen to prevent volatile compounds from reaching the vacuum system. The operation of short-path MD is based on using proper temperature, pressure, and feed mass flow. The feed was placed inside a dosing vessel (8) after being heated and melted. Then, the vacuum pump was turned on to remove gases from within the feed. Once a steady vacuum pressure was achieved and the distillation temperature was fixed, the feeding valve was turned on, allowing the degassed feed liquid to immediately flow down. A scraper quickly spun it into a very thin film that spread over an evaporating surface. Due to the heated walls and high vacuum, the more volatile and light components were concentrated onto a closely positioned internal condensing surface, forming the distillate. The less volatile and heavy components flowed down along the cylinder, forming the residue. Thus, the resulting fractions were separated and discharged through their respective outlets. The yields were calculated after collecting and measuring the amounts of distillates and residues.
ELA was distilled under two different conditions using a short-path MD apparatus. Two-step distillations were performed by varying the evaporation temperature from 90 °C to 145 °C. The ELA-containing liquid was placed inside the dosing vessel (capacity, 500 mL), and the different fractions were separated by modifying the pressure and temperature while wiper speed and flow were kept constant. During the first distillation, the evaporating temperature, internal condenser temperature, and operating pressure were set at 90 °C, 15 °C, and 1.0–3.0 mbar, respectively, resulting in two fractions called Distillate 1 (DF
1) and Residue 1 (RF
1). In the second distillation, RF
1 was distilled at evaporating temperature, internal condenser temperature, and operating pressure of 145 °C, 15 °C, and 0.01–0.05 mbar, respectively, resulting in two new fractions called Distillate 2 (DF
2) and Residue 2 (RF
2). The experimental conditions of the two processes are presented in
Table 2.
2.5. Fatty Acid Analysis Using GC–MS
Fatty acids were analyzed by GC–MS using conditions described previously [
20]. GC–electron impact ionization–MS analyses were performed using the 7000B GC–MS Triple Quad system (Agilent Technologies, Santa Clara, CA, USA) equipped with an SP
TM-2560 fused silica capillary column (100 m × 0.25 mm × 0.25 μm; Supelco, PA, USA). The temperatures of the injector and transfer line were kept at 250 °C. The initial temperature of the oven was kept at 140 °C for 5 min and then increased by 4 °C/min to 200 °C; the temperature was increased again by 3 °C/min to 220 °C and held for 26 min. The injection volume was 1.0 μL, using helium as the carrier gas at a flow rate of 1.0 mL/min. The split mode was applied at a ratio of 60:1, and the solvent was delayed by 3 min. The electron energy was 70 eV, and the temperature of the ion source was set to 230 °C. Results were recorded in GC–MS full-scan mode at a resolution of
m/z 50–500. Two groups (Foxtail millet bran oil and RF
2) were analyzed and then divided into three replicates for every group. ELA purity was analyzed by GC–MS according to the above conditions and calculated by the peak area normalization method.
4. Conclusions
In this study, a new method for separating and purifying ELA from FMB was optimized. The method uses UC and MD to obtain highly concentrated ELA. The optimal conditions, in UC process, identified via single-factor and response surface experiments were established as follows: 95% ethanol/urea ratio = 15:1 (w/w), urea/fatty acid ratio = 2.5:1 (w/w,; crystallization time = 15 h, and crystallization temperature = −6 °C. Under the optimal conditions, ELA concentration was 42.241%. We showed that response surface experiments can be used for regression analysis and parameter optimization of the UC process of foxtail millet bran oil. The ELA mixture was purified by MD in either one or two stages, and the best results were obtained using a one-stage purification with a distillation temperature of 145 °C and a pressure of 1.0–5.0 × 10−2 mbar. Under these conditions, ELA was purified to a level of 60.45%. By using both UC and MD, we were able to improve the total concentration of ELA in the final product. Therefore, ELA can be purified by the above method. The purification of ELA from FMB provides a resource for the field of health food and food for special medical purpose and adds value to subsidiary agricultural products.