Search Results (6)

Research on raw materials for Al₂O₃-SiC-C refractory castables used in blast furnace troughs is relatively well established. However, gaps remain in both laboratory and industrial trials concerning the performance of castables incorporating SiC-modified flake graphite and alternative carbon sources. This study investigated the sintering behavior, mechanical properties, and service performance of Al₂O₃-SiC-C castables utilizing varying contents of modified flake graphite, pitch, and carbon black as carbon sources. Samples were characterized using SEM, XRD, and EDS for phase composition and microstructural morphology analysis. Key findings revealed that the thermal expansion mismatch between the SiC coating and flake graphite in SiC-modified graphite generated a microcrack-toughening effect. This effect, combined with the synergistic reinforcement from both components, enhanced the mechanical properties. The SiC modification layer improved the wettability and oxidation resistance of the flake graphite. This modified graphite further contributed to enhanced erosion resistance through mechanisms of matrix pinning and crack deflection within the microstructure. However, the microcracks induced by thermal mismatch concurrently reduced erosion resistance, resulting in an overall limited net improvement in erosion resistance attributable to the modified graphite. Specimens containing 1 wt.% modified flake graphite exhibited the optimal overall performance. During industrial trials, this formulation unexpectedly demonstrated a water reduction mechanism requiring further investigation. Full article

Al₂O₃-SiC-C (ASC) castables containing spherical asphalt are widely utilized in high-temperature metallurgical furnaces because of their good abrasive resistance and slag resistance; however, the release of hazardous benzopyrene during the pyrosis process in spherical asphalt is detrimental to the environment and to the health of furnace workers. Herein, nontoxic nano carbon black (CB) was selected as the carbon source for ASC castables, and the effects of the CB amount and sintering atmosphere on the properties of ASC castables were investigated in this work. The results show that on increasing CB from 0.5% to 2%, the cold strength of the samples after firing in the reducing atmosphere increased, the residual strength increased, and the slag penetrated depth decreased; the reasons can be ascribed to nano CB being able to fill the pores to reduce the apparent porosity of the castables. Furthermore, SiC whiskers were formed at elevated temperatures and generated a network structure, which was beneficial in improving their properties. When CB was 1%, the cold modulus of the rupture of the samples after firing in the oxidizing atmosphere and reducing atmosphere were higher (about 20 MPa), the retained strength ratio of the samples pre-fired in the reducing atmosphere was the highest (85.4%), the hot strength at 1400 °C of the samples tested in the oxidized atmosphere was the highest (5.3 MPa), and the slag resistance of the samples measured in the oxidizing atmosphere was the best. The castables heat-treated in the air atmosphere possessed higher hot strength and slag resistance; the reasons can be attributed to the formed SiO₂ derived from the oxidation of SiC, which reacted with Al₂O₃ to form mullite, creating a strengthening effect and decreasing the porosity and increasing the viscosity of slag, thereby improving the hot strength and slag resistance. Full article

Aluminum metal matrix composites (Al MMCs) are a class of materials characterized by being light in weight and high hardness. Due to these properties, Al MMCs have various applications in the automobile, aeronautical and marine industries. Ceramic-reinforced Al MMCs in the form of sinters are known for having excellent abrasive properties, which makes them an attractive material in certain fields of technology. The biggest problem in their production process is their low ability to infiltrate ceramics with alloys and consequently the difficulty of filling a ceramic preform. The castability of such composites has not yet been researched in detail. The aim of this study was to create aluminum metal matrix composite castings based on aluminum alloys (AlSi11) reinforced with an Al₂O₃ sinter preform using a Castability Trials spiral mold, and then to determine the degree of saturation with the liquid metal of the produced ceramic shaped body (Castability Trials spiral). For the selected AlSi11 alloy, the liquidus (Tl) and solidus (Ts) temperatures were determined by performing thermal-derivation analysis during cooling, which is Tl—579.3 °C and Ts—573.9 °C. The resultant pressure necessary for the infiltration process was estimated for the reinforcement capillaries with the following dimensions: 10, 15, 20, 25, 30 and 35 microns. The following values were used to determine the capillary pressure (Pk): surface tension of the alloy—σ = 840 mN/m; the extreme wetting angle of the reinforcement by the metal—θ = 136°. It has been experimentally confirmed that for the vacuum saturation process, the estimated resultant pressure enables saturation of reinforcement with capillaries larger than 25 microns, provided that the alloy temperature does not drop lower than the infiltration temperature. After the experiment, the time and route of the liquid metal flow in the spiral were determined. On the basis of the obtained values, a simulation was developed and initial assumptions such as saturation time, alloy temperature, reinforcement and mold temperature were verified. The energy balance showed that the saturation limit temperature was Tk = 580.7 °C for the reinforcement temperature of 575 °C. In contrast to the above, the assumption that the temperature of the metal after equalizing the temperature of the composite components must be higher than the liquidus temperature (Tliq = 579.3 °C) for the aluminum alloy used must be fulfilled. After the experiment, the time and path of the liquid metal flow in the spiral were determined. Then, on the basis of the obtained values, a simulation was developed, and the initial assumptions (saturation time and temperature) were verified. Full article

Graphite flakes are commonly used to fabricate carbon-based refractories owing to their superior properties, including better corrosion resistance and thermal shock resistance (TSR); unfortunately, their insufficient water-wettability has remarkably hindered their application in castables. Aiming to enhance their water-wettability, a facile and low-cost technique for fabricating carbides coated in graphite was proposed in this work. Firstly, SiC-TiC coated graphite (SiC-TiC@C) powders were prepared via modified molten salt shielding synthesis in an air atmosphere using graphite flake, Si and Ti powders as raw materials and NaCl-KCl as the molten salt shielding medium. Water-wettability and oxidation resistance of SiC-TiC@C powders were significantly improved. Compared to the Al₂O₃-MgO castables with graphite flakes, the water demand of the castables with SiC-TiC@C was noticeably decreased from 6.85% to 4.89%, thereby decreasing the apparent porosity of the castables with 5% SiC-TiC@C (from 20.3% to 13%), enhancing the cold strength, hot strength and oxidation resistance of the castables. Such enhancements are ascribed to continuous and crack-free SiC-TiC coatings on graphite surfaces ensuring that the castables have outstanding properties. Full article

Colloidal bonds are realized by sol–gel technology. The binder system of the refractory castable belongs to the Al₂O₃–SiO₂ binary diagram. Mullite is the most thermally stable mineral in this system. This work was motivated by an attempt to maximize the mullite content in the NCC binder system, because a high content of mullite is a guarantee of the long service life of refractories. Initially, the mineralogical composition of the pure gel was tested after drying and firing at temperatures between 1000 °C and 1600 °C. The behavior of the gel during drying was described. Subsequently, a method of minimizing gel shrinkage during drying was sought. To this aim, fine fillers (microfillers) of alumina and silica were tested. In particular, the reactivity of the microfillers, the ability of the microfillers to react with the sol to form mullite, and the drying shrinkage of the microfiller-doped gel were evaluated. The study showed that the least suitable source of Al₂O₃ in terms of its reactivity is tabular corundum, which produces the lowest amount of mullite. The internal structure of the prepared binder system when using different microfillers was described. Based on the results from the second stage of the work, several complete matrixes of the binder system were designed and the degree of their mullitization at different firing temperatures was studied. During this stage, it was shown that the degree of mullitization of the binder system depends mainly on the microsilica content. In the binder system, the maximum mullite content recorded was 76%. The effect of amorphous SiO₂ on the bulk density and internal structure of the binder system was also described. Full article

Additions of andalusite aggregates (19 wt%) were shown in previous literature to enhance the antioxidation of Al₂O₃-SiC-C (ASC) castables. This work aims to investigate whether micronized andalusite has a greater influence on antioxidation improvement than andalusite aggregates. Various low contents (5 wt% and below) of micronized andalusite (≤5 μm) were introduced as a substitute for brown fused alumina in the matrix of ASC castables. The antioxidation of castable specimens was estimated by the oxidized area ratio on the fracture surface after a thermal shock test. The microstructure and phases of micronized andalusite and the castable specimens were characterized by scanning electron microscopy (SEM) and X-ray diffraction (XRD), respectively. The results suggest that the antioxidation effects of ASC castables with a low addition of micronized andalusite are effectively enhanced. The heat-induced transformation of andalusite produces SiO₂-rich glass, favoring the sintering of the castable matrix and impeding oxygen diffusion into the castable’s interior. Therefore, the castable antioxidation is enhanced without deteriorating the hot modulus of rupture. Full article