Search Results (670)

The development of high-performance adsorbents for treating dye-laden wastewater necessitates a deep understanding of structure–property relationships. This study presents a systematic investigation into the role of carbon material dimensionality (0D biochar, BC; 1D carbon nanotubes, CNT; 2D graphene oxide, GO) in modulating the properties of a dual physically crosslinked sodium alginate/polyacrylamide (SA/PAM) hydrogel for methylene blue (MB) adsorption. A series of composite hydrogels was fabricated via a sequential physical crosslinking strategy. Comprehensive characterization confirmed the successful incorporation and dispersion of carbon materials within the dual network. The three hydrogels showed good mechanical properties. Under the conditions of 25 °C, an initial MB concentration of 100 mg/L, and pH 10–11, the incorporation of carbon materials enhanced the adsorption capacity, with maximum adsorption capacities of 411.5, 410.6, and 422.8 mg/g for BC-H, GO-H, and CNT-H, respectively. Coexisting constituents in real water samples reduce adsorption capacity via competitive adsorption and interfacial interference. After five consecutive adsorption–desorption cycles, the adsorption capacities of BC-H, GO-H, and CNT-H decreased to 57.7%, 67.2%, and 61.7% of their initial values, respectively. Adsorption isotherm and kinetic studies revealed that the process followed the Langmuir model and pseudo-second-order kinetics, indicative of monolayer chemisorption. Mechanistic analysis identified synergistic contributions from electrostatic attraction, π-π stacking, and physical entrapment. Physical structural changes and chemical site occupation are the main reasons for the decrease in the adsorption performance of hydrogels during cyclic use. This work provides a rational design strategy for advanced adsorbents and a theoretical foundation for efficient dye wastewater remediation. Full article

This study presents the synthesis and use of a novel bamboo-derived magnetic activated carbon (BMAC) for the effective removal of cationic and anionic dyes, specifically methylene blue (MB), methyl orange (MO), and sunset yellow (SY), from aqueous solutions. The adsorbent was synthesized using thermal carbonization and subsequent inclusion of magnetic oxide, yielding a porous structure with improved adsorption and magnetic separation properties. Thorough characterization utilizing SEM, EDX, BET, FTIR, XRD, and TGA/DTA validated the creation of a highly porous material including uniformly dispersed magnetic particles and several surface functional groups. Batch adsorption tests were performed to examine the influences of contact time, adsorbent dosage, initial dye concentration, pH, and temperature. The findings indicated rapid adsorption kinetics, with equilibrium reached in around 60–70 min, and adsorption capacity ranked as MB > MO > SY. Augmenting adsorbent dosage enhanced removal efficiency but diminished adsorption capacity per unit mass due to site unsaturation. The maximum adsorption capacities (q_m) of BMAC were 58.9, 56.3, and 32.7 mg/g for MB, MO, and SY, respectively, as determined from the Langmuir isotherm model, indicating superior performance compared with other reported magnetic activated carbon. The adsorption process was determined to be exothermic and spontaneous, as evidenced by thermodynamic characteristics. The equilibrium data were optimally characterized by the Langmuir isotherm model, indicating monolayer adsorption, whereas the kinetic studies conformed to the pseudo-second-order model, signifying that chemisorption is predominant. The adsorption mechanism encompasses electrostatic interactions, π–π stacking, hydrogen bonding, van der Waals forces, pore filling, and surface complexation with magnetic oxides. The findings indicate that BMAC is an efficient, sustainable, and magnetically recoverable adsorbent for the elimination of both cationic and anionic dyes from wastewater. Full article

The development of adsorbents with high adsorption capacity, easy separation, and good reusability is critical for the treatment of dye-contaminated wastewater. Herein, a novel magnetic composite hydrogel, P(AA-AM)/SA-BC-Fe₃O₄, was synthesized via free radical polymerization, integrating acrylic acid (AA), acrylamide (AM), sodium alginate (SA), biochar (BC), and magnetic Fe₃O₄ nanoparticles. The material was systematically characterized by FTIR, XRD, SEM, BET, and VSM, which confirmed the successful formation of a three-dimensional porous network with well-dispersed Fe₃O₄ nanoparticles and BC, endowing the hydrogel with superparamagnetic properties. The adsorption performance of the hydrogel towards methylene blue (MB) was evaluated under various conditions. The results demonstrated that the adsorption process followed the pseudo-second-order kinetic model and the Langmuir isotherm, indicating that chemisorption is an important mechanism in the monolayer adsorption process. The hydrogel exhibited excellent swelling properties and remarkable pH-dependent adsorption behavior, with optimal performance in weakly alkaline environments. Notably, the incorporation of BC enhanced the adsorption capacity, while Fe₃O₄ enabled rapid magnetic separation, with the adsorbent retaining approximately 77% of its initial capacity after five regeneration cycles. This work presents a promising strategy for constructing magnetic hydrogel adsorbents that synergistically combine high adsorption efficiency, facile separability, and good reusability for practical wastewater treatment applications. Full article

The persistent accumulation of antibiotic pollutants in aquatic environments poses potential threats to ecological safety and human health, highlighting the importance of developing low-cost, high-performance adsorbents for their efficient removal. In this study, a hydrothermal method was employed to prepare highly dispersed coal gangue-based calcium silicate hydrate (CSH) adsorbents. The structural characteristics, adsorption performance, and adsorption mechanisms of the material were systematically investigated. The as-prepared CSH exhibited an interwoven nanorod/nanosheet composite morphology with a more developed pore structure and a higher specific surface area. Kinetic analysis indicated that the adsorption process followed a pseudo-second-order model and involved both Boyd diffusion and intraparticle diffusion, with liquid-film diffusion likely serving as the primary rate-limiting step. Isotherm analysis revealed that the adsorption behavior was well described by the Langmuir model, suggesting monolayer adsorption, with a theoretical adsorption capacity (Q_m) of 129.29 mg/g. Thermodynamic analysis further demonstrated that the adsorption of CIP onto CSH was a spontaneous and endothermic process. Combined characterization results and theoretical calculations suggested that the adsorption of CIP by CSH was mainly governed by surface oxygen containing active sites, accompanied by electrostatic interactions, hydrogen bonding, and possible surface coordination effects. In addition, CSH maintained excellent adsorption performance and structural stability in the presence of coexisting ions, in tap water systems, and after repeated adsorption–desorption cycles. This study not only enables the high-value utilization of coal gangue but also provides new insights into the development of low-cost adsorbent materials for antibiotic removal. Full article

Water contamination by arsenic(V) [As(V)] and Congo red (CR) dye poses concurrent threats to public health and aquatic ecosystems, particularly in regions where metallurgical and textile industries coexist. Developing a single adsorbent capable of simultaneously addressing these chemically distinct pollutants, while recovering value from the spent material remains an open challenge in sustainable water treatment. This study reports the synthesis and evaluation of a novel ternary MgZnFe-LDH/1,2,4-triazole composite (TM-LDH/TZ), engineered for the concurrent adsorptive removal of As(V) and CR, and the subsequent repurposing of the pollutant-loaded material as an electrocatalyst for the urea oxidation reaction (UOR). The composite was prepared via co-precipitation and triazole surface grafting, then characterized by FTIR, XRD, BET, TGA, FESEM, and HRTEM. Batch adsorption experiments examined the influence of pH, adsorbent dose, initial concentration, and temperature, with equilibrium data modeled through Langmuir, Freundlich, Temkin, and the statistically grounded Advanced Monolayer Model (AMM); kinetics were assessed using pseudo-first/second-order and Elovich models. Maximum Langmuir adsorption capacities reached 204.75 mg g⁻¹ for As(V) and 499.72 mg g⁻¹ for CR simultaneously at pH 5 and 25 °C, surpassing the majority of previously reported single-pollutant adsorbents. Elovich and pseudo-second-order kinetics confirmed chemisorption as the governing pathway for As(V) and CR, respectively, while AMM thermodynamic analysis verified spontaneous adsorption across all experimental conditions. The spent composite delivered a UOR peak current density of 184.67 mA cm⁻² that is nearly twice that of the fresh material, with a reduced charge-transfer resistance of 1.19 Ω, and removal efficiency remained above 85% through three successive regeneration cycles. The bifunctional design, coupling high-capacity dual-pollutant removal with catalytic valorization of waste, positions TM-LDH/TZ as a circular-economy-aligned platform for advanced water remediation. Full article

The widespread presence of pharmaceutical residues, particularly emerging antibiotics such as levofloxacin (LVX) and amoxicillin (AMOX), in aquatic environments poses serious risks to ecosystems and public health. In this study, magnetically modified biochar was synthesized from orange peel waste and evaluated for the percentage removal of LVX and AMOX from synthetic wastewater. The biochar was chemically modified with iron to enhance its adsorption capacity and facilitate magnetic separation. The physicochemical properties of raw and iron-modified biochar were characterized using Fourier-transform infrared spectroscopy (FTIR), scanning electron microscopy (SEM), and energy-dispersive X-ray spectroscopy (EDX). Batch adsorption experiments were conducted to investigate the effects of temperature, contact time, adsorbent dosage, pH, and initial antibiotic concentration on removal efficiency. Antibiotic concentrations were quantified using UV–Vis spectrophotometry. Batch adsorption experiments revealed that iron-modified biochar (FeMBC) significantly outperformed raw biochar (RBC) in antibiotic removal. Optimal removal efficiencies of 90% for AMOX and 92% for LVX were achieved at an adsorbent dosage of 0.1 g, antibiotic concentration of 10 mg L⁻¹, contact time of 120 min, and temperature of 30 °C. Equilibrium data were best described by the Langmuir isotherm model, indicating monolayer adsorption, with correlation coefficients of 0.98 for AMOX and 0.97 for LVX. Kinetic analysis showed that the pseudo-second-order model provided the best fit, suggesting that chemisorption dominated the adsorption process. Thermodynamic studies confirmed that the adsorption was spontaneous and exothermic. Overall, the results demonstrate that iron-modified orange peel biochar is an efficient (90% better removal efficiency than RBC), low-cost, and environmentally sustainable adsorbent for the removal of emerging antibiotics from pharmaceutical wastewater, offering strong potential for practical water treatment applications. Full article

Ammonium nitrogen (NH₄⁺-N) is a key biogenic pollutant in aquatic systems. This study evaluated natural diatomite (Aktobe region) and zeolite (Shankhanai, Zhetysu region) as low-cost, environmentally benign sorbents for NH₄⁺-N removal, and examined the effects of thermal (200–750 °C; 450 °C selected) and alkaline (0.5 M NaOH) treatments on their structural, textural and adsorption properties. Materials were characterized by XRD, XRF, FTIR, SEM-EDX and adsorption performance was assessed by kinetic and equilibrium experiments. Specific surface area and pore characteristics were determined from low-temperature nitrogen adsorption–desorption measurements, and the specific surface area was calculated using the Brunauer–Emmett–Teller (BET) method. Thermal treatment at 450 °C increased the specific surface area of diatomite (46.3 m²/g) and pore volume, and subsequent alkaline activation further enhanced adsorption activity. The modified diatomite achieved up to 84.6% removal of NH₄⁺-N with an equilibrium capacity q_max = 1.758 mg/g. Adsorption kinetics were best described by the pseudo-second-order (PSO) model, which may indicate a substantive role of surface chemical interactions. Equilibrium data were fitted with Langmuir and Freundlich models: the modified diatomite fitted Langmuir best (R² = 0.999), which may suggest predominance of a monolayer adsorption mechanism under the studied conditions, whereas natural samples and the zeolite were better described by the Freundlich model, reflecting likely surface energetic heterogeneity. Separation factor values (R_L = 0.068–0.643) indicate favorable adsorption within the investigated concentration range. The point of zero charge (pHpzc) was determined for all sorbents (5.3–6.3), confirming that at pH 7 the surface carries a negative charge favorable for electrostatic attraction of NH₄⁺ cations. Reusability tests over five consecutive adsorption–desorption cycles showed that modified diatomite and modified zeolite retained 93.4% and 92.3% of their initial removal efficiency, respectively, indicating acceptable stability under the applied regeneration conditions. These results demonstrate the potential of alkaline-modified diatomite and zeolite as effective sorbents for ammonium removal from wastewaters, contributing to the mitigation of eutrophication risks. Full article

Four algal adsorbents were prepared from two types of green sea algae (Ulva lactuca and Ulva pertusa), either by treatment with concentrated sulfuric acid or without treatment. A comparative study of Au(III) adsorption in an HCl medium was performed. While both untreated adsorbents showed good performance at low HCl concentrations, the treated adsorbents achieved quantitative adsorption and high selectivity for Au(III) across a broad range of HCl concentrations. The adsorption of Au(III) onto the algal biomass adsorbents followed the typical Langmuir monolayer adsorption model. At an HCl concentration of 0.010 M, the maximum adsorption capacities were 1.14, 0.86, 6.57, and 6.28 mol kg⁻¹ for DUL, DUP, TUL, and TUP, respectively. A kinetic study conducted at different temperatures was consistent with the pseudo-first-order kinetic model and enabled estimation of the activation energy of the adsorption reaction. Structural changes before and after treatment were analyzed using FT-IR spectroscopy. Confirmation of Au(III) adsorption and its subsequent reduction to the elemental state was achieved through XRD and SEM/EDX analyses as well as digital imaging of the Au-loaded adsorbents. Finally, the adsorbed and reduced Au was successfully desorbed using an acidic thiourea solution. Full article

Tetracycline antibiotics are increasingly detected in aquatic environments because of their ecological risks and persistence, while conventional wastewater treatment processes are often insufficient for their effective removal from water. Here, we introduce a novel 3D graphene oxide-based nanocomposite that stacks Cu-NPs and amino-functionalized MIL-101(Fe) (denoted by Cu/NH₂-MIL-101(Fe)@GO) to effectively remove tetracycline (TC) and oxytetracycline (OTC) from environmental water samples. XPS, XRD, TEM, SEM, and FTIR analyses were conducted to characterize the structure and surface morphology of the Cu/NH₂-MIL-101(Fe)@GO nanocomposite. Overall, it was confirmed that GO, NH₂-MIL-101(Fe), and Cu-NPs were successfully incorporated, resulting in a porous material with high access to Cu-related sites as well as oxygen- and nitrogen-based functionalities (such as amino-, hydroxy-, and carboxy-groups). This hybrid system facilitates the adsorption by complementary mechanisms like surface complexation/chelation at Cu and Fe centers with the pH-dependent tetracycline species in electrostatic interactions, hydrogen bonding, π–π stacking, and molecule confinement in the metal–organic framework (MOF) pores, and by the synergistic effects at the GO–MOF(Fe)–Cu junction interfaces. The batch adsorption studies showed that the quick and efficient uptake of the two antibiotics at pH 6.5, with removal rates of 99.65–99.83%, was achieved by 15.0 mg of Cu/NH₂-MIL-101(Fe)@GO at an initial concentration of 20 ppm in 40 min at 25 °C. Equilibrium data were found to be well-fitted by the Langmuir isotherm (R² = 0.908–0.909), suggesting monolayer-dominated adsorption with the maximum capacity of 769.8–775.2 mg g⁻¹. The adsorption kinetics was well-described by the pseudo-second order model (R² = 0.9641–0.9749), which agreed with the strong binding between the tetracyclines and active sites of the nanocomposite. The main novelty of this work consists of the design of a single recoverable platform integrating GO-based preconcentration, pore accessibility of NH₂-MIL-101(Fe), and Cu-driven complexation, which led to the strong removal of tetracyclines under a relevant range of water conditions. These findings demonstrate that Cu/NH₂-MIL-101(Fe)@GO could serve as a promising high-efficiency and potentially reusable adsorbent for removing tetracycline from aqueous solution, which provides a more sustainable approach for pharmaceutical wastewater treatment. Full article

Pharmaceutical residues continue to increasingly contaminate water systems at a global level, and conventional wastewater treatment plants are unable to completely remove these emergent compounds. This study investigates the benzocaine adsorption from aqueous solutions onto Amberlite XAD-7 (X7) resin, with emphasis on quantitative performance metrics and mechanistic understanding. Adsorption occurred rapidly, reaching equilibrium within 60 min, with a maximum adsorption capacity (Q_e) of 140 mg/g and a Langmuir monolayer capacity of 147 mg/g. Experimental parameters strongly influenced X7 performance: resin dosage (0.01–0.05 g) and agitation speed (25–200 rpm) enhanced removal efficiency from 10% to 99.9%, while pH variation (5–9) had a negligible effect, confirming a predominantly hydrophobic, non-ionic adsorption mechanism. Equilibrium data are best described by the Langmuir model (R² = 0.9920, b = 5.2 L/mg, RL = 0.0003), indicating highly favorable monolayer adsorption, while kinetic behavior is described by the pseudo-second-order (PSO) model. FTIR-ATR analysis confirms benzocaine retention through characteristic shifts in aromatic, amine, and ester bands. TG/DSC measurements prove the thermal stability of X7 and the incorporation of benzocaine within the polymeric matrix. Desorption efficiencies ranged from 40% (NaOH) to 97% (HCl-ethanol mixture), demonstrating that X7 was regenerated under the tested conditions with a single cycle. Overall, X7 exhibits high capacity, robustness, and recyclability, highlighting its strong potential for efficient benzocaine removal from contaminated wastewater. Full article

Metal oxide nanoparticles dispersed in water are difficult to recover because of their small size and colloidal stability. In this study, the interfacial adsorption behavior of Fe₂O₃, CoO, and CuO nanoparticles at hydrophobic ionic liquid (IL)–water interfaces was investigated and compared with that at molecular solvent–water interfaces. When CuO nanoparticle dispersions were shaken with hydrophobic ILs, bis(trifluoromethanesulfonyl)imide ([NTf₂]⁻) salts of 1-butyl-3-methylimidazolium ([BMIm]⁺) and 1-octyl-3-methylimidazolium ([OMIm]⁺), the nanoparticles were removed from the aqueous phase and accumulated at the IL–water interface, while negligible Cu was detected in the bulk IL phase. The removal efficiency decreased with increasing ionic strength below 0.05 mol/dm³ and increased with pH, indicating that electrostatic interactions between charged nanoparticles and the IL–water interface contribute to adsorption. Adsorption isotherms were empirically fitted with the Langmuir equation to estimate the maximum adsorption capacity. For negatively charged Fe₂O₃ and CuO nanoparticles, the maximum adsorption capacities at IL–water interfaces exceeded those at molecular solvent–water interfaces and the theoretical monolayer capacity estimated from nanoparticle size, suggesting multilayer adsorption or aggregation at the interfaces. These results demonstrate the potential of hydrophobic IL–water interfaces for the separation and recovery of metal oxide nanoparticles from aqueous media. Full article

The development of efficient and low-cost adsorbents for dye-contaminated wastewater remains an important challenge in environmental remediation. In this study, an interlayer-expanded polypyrrole/maghnite–Cu²⁺ nanocomposite (PPy/Mag–Cu²⁺) was successfully synthesized through purification of raw maghnite, sodium activation, Cu²⁺ ion exchange, and in situ oxidative polymerization of pyrrole. The obtained hybrid was characterized by X-ray fluorescence, X-ray diffraction, Fourier-transform infrared spectroscopy, UV–Vis spectroscopy, scanning electron microscopy, and cyclic voltammetry. The results confirmed the successful incorporation of Cu²⁺ and polypyrrole while preserving the layered aluminosilicate framework. XRD analysis revealed a progressive increase in basal spacing from 17.49 Å for raw maghnite to 25.95 Å for the final nanocomposite, indicating effective intercalation and formation of an expanded hybrid structure. The adsorption performance of PPy/Mag–Cu²⁺ was evaluated for methylene blue removal under batch conditions. Adsorption was strongly influenced by contact time, pH, and initial dye concentration, with equilibrium reached after approximately 80 min and optimum removal at pH 9. Equilibrium data were best fitted by the Langmuir model, with a maximum monolayer adsorption capacity of 43.66 mg g⁻¹, while kinetic data followed the pseudo-second-order model. These findings demonstrate that PPy/Mag–Cu²⁺ is a promising and cost-effective hybrid adsorbent for cationic dye removal from aqueous media. Full article

Cannabinol (CBN) is a highly lipophilic phytocannabinoid whose biomedical application is limited by poor water solubility. In this study, colloidal hydroxyapatite nanoparticles (nHAp) were evaluated as a carrier for CBN, and their effect on model lipid membranes was investigated. Interactions between CBN and lipids were examined using Langmuir monolayers and lipid bilayers (black lipid membranes, BLMs). Langmuir monolayer studies revealed strong interactions between CBN and lipids, resulting in changes in isotherms, compressibility, and monolayer stability. BLM measurements indicated that delivery of CBN via nHAp modifies the electrical properties and stability of the lipid bilayer, suggesting alterations in membrane organization and permeability. These results demonstrate that hydroxyapatite nanoparticles can effectively serve as a carrier for cannabinol while modulating its interactions with lipid membranes. Full article

In this study, chicken bone biochar (CBC) was prepared from waste chicken bones via oxygen-limited pyrolysis. A magnetic component (Fe₃O₄) was introduced, and the composite was embedded in a sodium alginate (SA) gel network, successfully constructing magnetic chicken bone biochar/sodium alginate composite gel beads (M-CBC/SA). The experimental results showed that under the conditions of pH = 4.5, 25 °C, and an adsorbent dosage of 0.5 g/L, the removal efficiency of M-CBC/SA toward 50 mg/L U(VI) reached 91.67%, corresponding to an adsorption capacity of 91.67 mg/g. The adsorption process followed the pseudo-second-order kinetic model and the Langmuir isotherm model, with a theoretical maximum adsorption capacity of 322.58 mg/g, indicating that the adsorption was dominated by monolayer chemisorption. The material exhibited excellent magnetic separability and good anti-interference ability against coexisting ions such as K⁺, Na⁺, Cl⁻, and SO₄²⁻, and its adsorption behavior was only weakly affected by ionic strength. Characterization by XRD, FTIR, XPS, SEM-EDS and other techniques revealed that the immobilization mechanism of U(VI) involved the synergistic effects of dissolution–precipitation (the formation of a new autunite phase), surface complexation (involving hydroxyl and phosphate groups), ion exchange (exchange with Ca²⁺), and electrostatic attraction. Using waste chicken bones as the raw material, this composite achieves both efficient uranium immobilization and convenient magnetic separation, fully embodying the environmental concept of “treating waste with waste”, and shows promising application prospects in the treatment of uranium-containing wastewater. Full article

Chitosan is a well-known heavy metal biosorbent and was incorporated into birch sanding dust mycelium bio-composites (MBs). The chitosan-hybridized MBs with different chitosan contents were characterized by microscopy, porous structure analyses (specific surface area and total pore volume), pH_pzc, functional group content, and FTIR. Microscopy did not reveal any antifungal effect of chitosan on Trametes versicolor. The porous structure of the MBs decreased after hybridization with chitosan. The FTIR spectra and functional group analyses confirmed the presence of chitosan amino groups in the MBs. The chitosan-hybridized MBs were subjected to the adsorption of heavy metals, namely Cu(II) and Cd(II), and the removal percentage and adsorption isotherms were evaluated. Adsorption isotherms were analyzed using the Freundlich and Langmuir models. The results showed a significant increase in the maximum monolayer adsorption capacity for Cu(II), calculated using the Langmuir equation, from <2 mg/g for raw BSD and basic MB without chitosan to 19 mg/g for the MB with 15% chitosan. In the case of Cd(II), no significant increase in adsorption capacity was observed. These findings indicate that hybridization of MBs with chitosan is a promising approach to improve the Cu(II) adsorption capacity of MBs. Full article