Search Results (9,132)

To address the challenges of complex composition, high chemical oxygen demand (COD) content, and the difficulty of treating organic wastewater from brewery wastewater, as well as the limitations of traditional Fenton technology, including low catalytic activity and high material costs, this study proposes the use of biochemical sludge as a raw material. Coupled with iron salt activation and mechanical ball milling technology, a low-cost, high-performance iron-doped mesoporous nano-sludge biochar material is prepared. This material was employed as a particle electrode to construct a three-dimensional electro-Fenton system for the degradation of organic wastewater from sauce-flavor liquor brewing. The results demonstrate that the sludge-based biochar produced through this approach possesses a mesoporous structure, with an average particle size of 187 nm, a specific surface area of 386.28 m²/g, and an average pore size of 4.635 nm. Iron is present in the material as multivalent iron ions, which provide more electrochemical reaction sites. Utilizing response surface methodology, the optimized treatment process achieves a maximum COD degradation rate of 71.12%. Compared to the control sample, the average particle size decreases from 287 μm to 187 nm, the specific surface area increases from 44.89 m²/g to 386.28 m²/g, and the COD degradation rate improves by 61.1%. Preliminary investigations suggest that the iron valence cycle (Fe²⁺/Fe³⁺) and the mass transfer enhancement effect of the mesoporous nano-structure are keys to efficient degradation. The Fe-O-Si structure enhances material stability, with a degradation capacity retention rate of 88.74% after 30 cycles of use. When used as a particle electrode to construct a three-dimensional electro-Fenton system, this material demonstrates highly efficiency in organic matter degradation and shows promising potential for application in the treatment of organic wastewater from sauce-flavor liquor brewing. Full article

Forests play a crucial role in climate regulation through atmospheric CO₂ sequestration. However, disturbances like wildfires can severely compromise this function. This study assesses the ecological and economic consequences of a 2018 wildfire in The Roaches Nature Reserve, UK, focusing on post-fire carbon dynamics. A mixed woodland dominated by Pinus sylvestris L. and Larix decidua Mill. was evaluated via satellite imagery (remote sensing indices), dendrochronological analysis (wood cores sampling), and soil properties analyses. Remote sensing revealed areas of high fire severity and progressive vegetation decline. Tree-ring data indicated near-total mortality of L. decidua, while P. sylvestris showed greater post-fire resilience. Soil properties (e.g., soil organic carbon, biomass and microbial indices, etc.) assessed at a depth of 0–5 cm showed no significant changes. The analysis of CO₂ sequestration trends revealed a marked decline in burned areas, with post-fire sequestration reduced by approximately 70% in P. sylvestris and nearly 100% in L. decidua, in contrast to the stable patterns observed in the control stands during the same period. To estimate this important ecosystem service, we developed a novel CO₂ Sequestration Loss (CSL) index, which quantified the reduction in forest carbon uptake and underscored the impaired sequestration capacity of burned area. The decrease in CO₂ sequestration also resulted in a loss of regulating ecosystem service value, with burned areas showing a marked reduction compared to pre-fire conditions. Finally, a carbon loss of ~208 Mg ha⁻¹ was estimated in the burnt area compared to the control, mainly due to tree mortality rather than shallow soil carbon stock. Overall, our findings demonstrate that wildfire can substantially compromise the climate mitigation potential of temperate forests, highlighting the urgency of proactive management and restoration strategies. Full article

Urban expansion alters environmental conditions, influencing tree physiology and performance. Urban trees provide cooling, sequester carbon, support biodiversity, filter contaminants, and enhance human health. This study examines how two common urban trees—Norway Maple (Acer platanoides L.) and Little-leaved Linden (Tilia cordata Mill.)—respond to urban site conditions by assessing leaf morphology, stomatal, and gas exchange traits across street and urban park sites in Chicago, IL. Street trees exhibited structural trait adjustments, including smaller leaf area, reduced specific leaf area, and increased stomatal density, potentially reflecting acclimation to more compact and impervious conditions. Norway Maple showed stable photosynthetic assimilation (A), stomatal conductance (g_s), and transpiration (E) across sites, alongside higher intrinsic water-use efficiency (_iWUE), indicating a conservative water-use strategy. In contrast, Little-leaved Linden maintained A and g_s but showed elevated E and _iWUE at street sites, suggesting adaptive shifts in water-use dynamics under street microenvironments. These findings highlight how species-specific physiological strategies and local site conditions interact to shape tree function in cities and underscore the importance of incorporating functional traits into urban forestry planning to improve ecosystem services and climate resilience. Full article

This study aimed to evaluate the impact of different adhesive solutions on the surface roughness and hardness of denture base materials. Twenty specimens (20 × 20 × 5 mm) were produced for each material group: heat-cured ProBase Hot^®, 3D-printed NextDent Denture 3D+^®, and PMMA-milled Exaktus^®. They were then divided into five solution subgroups (n = 4): control (T0), distilled water, Corega PowerMax^®, Elgydium Fix^®, and Kukident Pro Ultimate^®. Specimens were immersed in the solution at 37 °C daily for 28 days, simulating continuous use. Profilometry and Shore D hardness tests were performed at baseline and after 28 days of the immersion protocol. Data analysis was done using IBM SPSS Statistics 30.0, considering a confidence level of 0.05. At baseline, the materials differed in surface roughness and Shore D hardness, with the 3D-printed group showing the highest median values for the Rz parameter (p = 0.023) and the lowest for hardness (p = 0.023). Elgydium Fix had a significant effect on the heat-cured resin, with increased Rz and decreased hardness. Kukident caused higher roughness and lower hardness in the 3D-printed and milled resins (not significant). Corega showed minor effects in all tested materials. In conclusion, the denture base material and the adhesive formulation influence the physical and mechanical properties of denture base resins. Full article

Climatic factors have always played a key role in the construction of food-related architecture: mitigation of outdoor temperatures or winds, adoption of raining waters in the productive processes, etc. However, sometimes, climate change has impacted the profitability of those structures and eventually caused their abandonment. Today, historical food-related architectures are significant elements of local rural heritage, and they are also tangible symbols of all the values connected to the corresponding typical food productions. When the cultural value of rural cultural assets and the historical management of climatic factors coexist, this potential can be investigated, and the results can ultimately be included in the corresponding enhancement processes. To exploit this potential, the paper introduces the theoretical concept of food-related architecture as climatic indicators, with reference to the changes in the climate that have occurred during their construction, as well as their abandonment. According to the thesis of the research, the adoption of the concept of climatic indicators can implement the value of selected minor cultural assets, support sustainable rural regeneration plans and integrate missing historical climate series and data. In the Materials and Methods section, two theoretical charts have been introduced, and the pyramid of the Mediterranean diet was analyzed to allow for the selection of some food-related architectures to test the theoretical approach developed. Then, three Italian case studies have been analyzed: the concept of climate indicators was tested, and some potential focus points of actions connected to this aspect were elucidated. The case studies are the Pietragalla wine district in the Basilicata Region, the Apulian rock-cut oil mills and Mills’s Valley in the Campania Region. Full article

This study evaluated the effect of dietary supplementation with different levels of spray-dried phenolic compounds, extracted from olive mill wastewater, on the volatile compound profile of Caciotta cheese produced from cow’s milk. Thirty dairy cows were divided into three groups and fed diets containing 0% (C), 0.1% (T0.1), and 0.2% (T0.2) polyphenols on a dry matter basis. Milk from each group was used in three cheesemaking sessions, and 27 cheese samples ripened for 21 days were analyzed. Volatile compounds were extracted using solid phase microextraction (SPME) coupled with mass spectrometry, while the odour fingerprint was assessed using an electronic nose (PEN3). Principal Component Analysis (PCA) revealed a clear separation among groups, indicating distinct aromatic profiles associated with dietary polyphenol levels. In summary, incorporating by-products from olive mill wastewater into the diets of dairy cows can significantly affect the aroma of cheese. This approach represents a sustainable and innovative strategy that promotes waste valorization, reduces environmental impact, and supports circular economy principles by transforming a pollutant into a valuable additive. Full article

Yttria-stabilized zirconia(YSZ) was introduced into the Al₂O₃-TiO₂-CeO₂ coating prepared by plasma spraying to improve the wear resistance of the coating and prolong the service life of the weathering steel. The nano-agglomerated powder was prepared by mechanical ball milling and spray-drying technology, powder was sprayed on the surface of Q355 steel substrate by atmospheric plasma sparing (APS), the Al₂O₃-TiO₂-CeO₂/YSZ composite coating was prepared, and the effects of YSZ on the phase, microstructure, and tribological properties of the composite coating were studied. The results show that nano-agglomerated powders with micron size (average size 55 μm) can be prepared by spray-drying technology, and after high-temperature sintering, the nano-agglomerated powders are denser and form the α-Al₂O₃ phase. The composite coating prepared by plasma spraying has a bimodal structure, and after adding YSZ, the phases in the coating are mainly α-Al₂O₃, γ-Al₂O₃, and t-ZrO₂, the grain size is fine, and the porosity is reduced. The specific wear rate is only 4.4 × 10⁻⁵ mm³ N⁻¹·m⁻¹, the relative wear resistance is 6.3 times higher than that of the substrate, and the wear mechanism of the coating is mainly slight adhesive wear and abrasive wear, which shows excellent friction and wear properties at room temperature. Full article

The olive tree (Olea europaea L.) has been cultivated for millennia, with olive oil representing both a cornerstone of the Mediterranean diet and a major agricultural commodity. Its composition, rich in monounsaturated fatty acids, polyphenols, tocopherols and squalene, supports well-documented cardioprotective, antioxidant and anti-inflammatory benefits. Olive oil production generates substantial secondary streams, including pomace, leaves, pits and mill wastewater, which are rich in phenols, triterpenes and fibers. This review consolidates recent advances in their phytochemical characterization, innovative extraction technologies and health-promoting effects, while highlighting the economic and regulatory prospects for industrial adoption. Comparative analysis shows that olive leaves can produce up to 16,674.0–50,594.3 mg/kg total phenolics; oleuropein 4570.0–27,547.7 mg/kg, pomace retains 2.24 g GAE/100 g dried matrix (DM)total phenolics; oil 13.66% DM; protein 6.64% DM, and wastewater contains high concentration of phenolics content of olives. Innovative extraction techniques, such as ultrasound and microwave-assisted methods, allow for a recovery, while reducing solvent use and energy input. The analysis highlights opportunities for integrating these by-products into circular bioeconomy models, supporting the development of functional foods, nutraceutical applications and sustainable waste management. Future research should address techno-economic feasibility, regulatory harmonization and large-scale clinical validation to accelerate market translation. Full article

This in vitro study evaluated the fracture resistance of metal–ceramic crowns repaired with milled hybrid resin, printed hybrid resin, lithium disilicate, and direct composite resin. One hundred crowns were fabricated, fractured under controlled loading, and 80 with standardized defects were randomly assigned to four groups (n = 20). Repairs were performed using CAD/CAM onlays or direct composite, followed by compressive testing until fracture. Mean fracture resistance values ranged from 1858.95 N to 1997 N across all groups, exceeding typical posterior occlusal forces (700–900 N). No statistically significant differences were found among groups (p = 0.200). Most failures were cohesive. These results indicate that both digital (milled and printed) and direct techniques offer sufficient strength to serve as minimally invasive and cost-effective alternatives to full crown replacement. Although limited by the in vitro design, this study supports the applicability of modern repair approaches in daily practice. Full article

Fe-CNT composites were synthesized via mechanical ball milling, incorporating varying amounts of carbon nanotubes (CNTs) into iron powder at concentrations of 1wt%, 2wt%, and 3wt%. The impact of different CNT contents on the phase structure, microstructure, and magnetic properties of the composites was examined. Raman spectroscopy and X-ray diffraction (XRD) analyses revealed that despite some damage, CNTs retained a predominantly one-dimensional nanostructure post-ball milling. Moreover, an increase in CNT content led to a gradual rise in grain size and lattice strain of the iron powder, attributed to the formation of solid solutions and iron–carbon compounds. Scanning electron microscopy (SEM) observations demonstrated that the majority of CNTs were integrated within the iron matrix particles, with a minority either partially embedded or entirely unembedded on the iron powder surface. With higher CNT concentrations, local CNT agglomeration emerged and intensified. Vibrating sample magnetometer (VSM) measurements indicated that Fe-CNT composites exhibited enhanced saturation magnetization (2.25%) and reduced coercivity (91.74%) compared to pure iron, underscoring the potential of CNTs in enhancing the magnetic properties of iron powder. Full article

Background/Objectives: Pharmaceutical preparation technologies can enhance the bioavailability of poorly water-soluble drugs. Ursolic acid (UA) has been found to possess anti-cancer and hepatoprotective properties, demonstrating its potential as a therapeutic agent; however, its hydrophobicity and low solubility present challenges in the development of drug formulations. This study investigates the preparation of a nano-UA suspension by wet grinding, researches the influence of process parameters on particle size, and explores the rules of particle breakage and agglomeration by combining model fitting. Methods: Wet grinding experiments were conducted using a laboratory-scale grinding machine. The particle size distributions (PSDs) of UA suspensions under different grinding conditions were measured using a laser particle size analyzer. A single-factor experimental design was employed to optimize operational conditions. Model parameters for a population balance model considering both breakage and agglomeration were determined by an evolutionary algorithm optimization method. By measuring the degree to which UA inhibits the colorimetric reaction between salicylic acid and hydroxyl radicals, its antioxidant capacity in scavenging hydroxyl radicals was indirectly evaluated. Results: Wet grinding process conditions for nano-UA particles were established, yielding a UA suspension with a D50 particle size of 122 nm. The scavenging rate of the final grinding product was improved to three times higher than that of the UA raw material (D50 = 14.2 μm). Conclusions: Preparing nano-UA suspensions via wet grinding technology can significantly enhance their antioxidant properties. Model regression analysis of PSD data reveals that increasing the grinding mill’s stirring speed leads to more uniform particle size distribution, indicating that grinding speed (power) is a critical factor in producing nanosuspensions. Full article

Background: The adhesion between artificial teeth and denture bases is crucial for the longevity of complete dentures. This in vitro study evaluated the shear bond strength (SBS) and failure modes between artificial teeth and denture base resins produced with conventional, milled, and 3D-printed techniques. Materials: A total of 105 specimens were fabricated and assigned to 7 groups (n = 15) combining conventional, milled, or printed denture bases with conventional, milled, or printed teeth. SBS was tested using a universal testing machine, and failure modes were classified as adhesive, cohesive, or mixed. Data were analyzed with one-way ANOVA and Tukey’s post hoc test (α = 0.05). Results: SBS significantly varied among groups (p < 0.001). The conventional base–conventional tooth group (CB-CT) showed the highest bond strength (14.9 ± 3.69 MPa), while the printed base–milled tooth group (PB-MT) had the lowest (6.58 ± 3.41 MPa). Milled base groups showed intermediate values (11.7–12.4 MPa). Conclusions: Bond strength between denture teeth and denture bases depends on the fabrication workflow. Conventional heat-cured PMMA bases exhibited the most reliable adhesion, while milled bases demonstrated satisfactory performance with optimized bonding. Printed bases showed reduced and variable adhesion, suggesting the need for improved bonding protocols before their widespread clinical application in definitive prostheses. Full article

Significant depletion of natural resources, coupled with increased environmental pollution resulting from the constant evolution of global industrialization, poses a considerable problem. Therefore, it is unsurprising that sustainable “green” chemistry and technology are gathering the worldwide scientific community, whose common goal is to find applicable solutions for the abovementioned problems. This paper combined the ultrasonic extraction method (a form of “green” technology) with natural deep eutectic solvents (NADESs, a type of “green” solvent) for the production of extracts from an industrial by-product (discarded waste wild apple dust). Waste wild apple dust was pretreated with different NADESs in order to explore the pretreatment benefits regarding ultrasonic extraction of bioactive compounds. Among all solvents used, aqueous propylene glycol was chosen as the best system, which, combined with Reline NADES pretreatment, provided the highest TPC and TFC values, together with the best antioxidant activities. UHPLC-DAD-MS analyses of extracts revealed the presence of natural organic acids, quercetin and kaempferol derivatives, tannins, and flavones. Following this procedure, valorization of agro-industrial apple herbal waste resulted in obtaining extracts with high potential for utilization in different industrial branches (food and pharmaceutical industries), contributing to both cleaner production and reduced environmental impact. Full article

In industrial bamboo machining, the suboptimal selection of cutting parameters leads to elevated cutting power and increased surface roughness. To enhance the machinability of bamboo, a multi-objective optimization of cutting parameters was conducted using orthogonal experimental methods, with special focus on the influences of fiber direction, feed per tooth, and cutting speed on cutting power and surface roughness. The main findings of this study are summarized as follows: feed per tooth exhibited the greatest effect on cutting power, followed by cutting speed and fiber direction. In contrast, fiber direction exerted the most substantial influence on surface roughness, with feed per tooth and cutting speed ranking second and third, respectively. Furthermore, the optimal milling parameters for minimizing both cutting power and surface roughness were identified as a fiber direction of 0°, a feed per tooth of 0.2 mm/z, and a cutting speed of 400 m/min. Therefore, the obtained optimal parameters are recommended for industrial bamboo machining to achieve reduced cutting power and improved surface quality. Full article

This study presents a sustainable upcycling strategy to convert “Pit,” a carbon-rich coke oven by-product from steel manufacturing, into high-purity graphite for use as an anode material in lithium-ion batteries. Despite its high carbon content, raw Pit contains significant impurities and has irregular particle morphology, which limits its direct application in batteries. We employed a multi-step, additive-free refinement process—including jet milling, spheroidization, and high-temperature graphitization—to enhance carbon purity and structural properties. The processed Pit-derived graphite showed a much-improved particle size distribution (D50 reduced from 25.3 μm to 14.8 μm & Span reduced from 1.72 to 1.23), increased tap density (from 0.54 to 0.80 g/cm³), and reduced BET surface area, making it suitable for high-performance lithium-ion batteries anodes. Structural characterization by XRD and TEM confirmed dramatically enhanced crystallinity after graphitization (graphitization degree increasing from ~13 for raw Pit to 95.7% for graphitized Pit at 3000 °C). The fully processed graphite (denoted S_Pit3000) delivered a reversible discharge capacity of 346.7 mAh/g with an initial Coulombic efficiency of 93.5% in half-cell tests—comparable to commercial artificial graphite. Furthermore, when composited with silicon oxide to form a hybrid anode, the material achieved an even higher capacity of 418.0 mAh/g under high mass loading conditions. These results highlight the feasibility of transforming industrial coke waste into value-added electrode materials through environmentally friendly physical processes. The upcycled graphite anode meets industrial performance standards, demonstrating a promising route toward circular economy solutions in both the steel and battery industries. Full article