Search Results (4)

Strict gaseous emission standards are applied globally to regulate the maximum amounts of pollutant emissions that can be produced from all vehicles. The exhaust aftertreatment systems used by automotive manufacturers rely on the utilization of precious metals (Pt, Pd, Rh). However, much effort has been devoted on the reduction or the replacement of the amount of Platinum Group Metals (PGMs) in three-way catalysts (TWC), both from a cost-effectiveness as well as an environmental point of view. PROMETHEUS catalyst, which was recently homologated for Euro 6 applications, is a low-cost, Cu-based TWC, which consists of a significantly lower quantity of PGMs compared to conventional state-of-the-art catalysts and achieves similar or even better catalytic efficiencies. In this review paper, a complex reaction scheme is proposed for the first time for a catalytic converter utilizing Cu and PGMs, following an extensive literature investigation of the available models. The scheme also accounts for the surface reaction mechanisms of the main processes and the side reactions potentially taking place during the TWC operation in the presence of Cu and at least one of the following PGMs: Pt, Pd or Rh. At a next step, the proposed reaction scheme will be validated based on experimental data, using mathematical modelling of a PROMETHEUS catalytic converter incorporating Cu and PGM nanoparticles. Full article

The global trend in restrictions on pollutant emissions requires the use of catalytic converters in the automotive industry. Noble metals belonging to the platinum group metals (PGMs, platinum, palladium, and rhodium) are currently used for autocatalysts. However, recent efforts focus on the development of new catalytic converters that combine high activity and reduced cost, attracting the interest of the automotive industry. Among them, the partial substitution of PGMs by abundant non-PGMs (transition metals such as copper) seems to be a promising alternative. The PROMETHEUS catalyst (PROM100) is a polymetallic nanosized copper-based catalyst for automotives prepared by a wet impregnation method, using as a carrier an inorganic mixed oxide (CeO₂-ZrO₂) exhibiting elevated oxygen storage capacity. On the other hand, catalyst deactivation or ageing is defined as the process in which the structure and state of the catalyst change, leading to the loss of the catalyst’s active sites with a subsequent decrease in the catalyst’s performance, significantly affecting the emissions of the catalyst. The main scope of this research is to investigate in detail the effect of ageing on this low-cost, effective catalyst. To that end, a detailed characterization has been performed with a train of methods, such as SEM, Raman, XRD, XRF, BET and XPS, to both ceria–zirconia mixed inorganic oxide support (CZ-fresh and -aged) and to the copper-based catalyst (PROM100-fresh and -aged), revealing the impact of ageing on catalytic efficiency. It was found that ageing affects the Ce–Zr mixed oxide structure by initiating the formation of distinct ZrO₂ and CeO₂ structures monitored by Raman and XRD. In addition, it crucially affects the morphology of the sample by reducing the surface area by a factor of nearly two orders of magnitude and increasing particle size as indicated by BET and SEM due to sintering. Finally, the Pd concentration was found to be considerably reduced from the material’s surface as suggested by XPS data. The above-mentioned alterations observed after ageing increased the light-off temperatures by more than 175 °C, compared to the fresh sample, without affecting the overall efficiency of the catalyst for CO and CH₄ oxidation reactions. Metal particle and CeZr carrier sintering, washcoat loss as well as partial metal encapsulation by Cu and/or CeZrO₄ are identified as the main causes for the deactivation after hydrothermal ageing. Full article

PROMETHEUS catalyst, a copper-based polymetallic nano-catalyst has been proven to be suitable for automotive emission control applications. This novel catalyst consists of copper, palladium and rhodium nanoparticles as active phases, impregnated on an inorganic oxide substrate, CeO₂/ZrO₂ (75%, 25%). The aim of PROMETHEUS catalyst’s development is the substitution of a significant amount (85%) of Platinum Group Metals (PGMs) with copper nanoparticles while, at the same time, presenting high catalytic efficiency with respect to the commercial catalysts. In this work, an extensive investigation of the catalytic activity of full scale PROMETHEUS fresh and aged catalyst deposited on ceramic cordierites is presented and discussed. The catalytic activity was tested on an Synthetic Gas Bench (SGB) towards the oxidation of CO and CH₄ and the reduction of NO. The loading of the washcoat was 2 wt% (metal content) on Cu, Pd, Rh with the corresponding metal ratio at 21:7:1. The concentration of the full-scale monolithic catalysts to be 0.032% total PGM loading for meeting Euro III standard and 0.089% for meeting Euro IV to Euro VIb standards. The catalytic activity of all catalysts was tested both in rich-burn (λ = 0.99) and lean-burn conditions (λ = 1.03). Full article

According to the strict European exhaust emissions standards that have been imposed by European legislation there is an elevated need for the decrease of the toxic gas emissions from vehicles. Therefore, car manufacturers have implemented a series of catalytic devices in the aftertreatment of the engine to comply with the standards. All catalytic devices (such as three-way catalysts, diesel particulate filters and diesel oxidation catalysts) accumulate concentrated loading of platinum group metals (PGMs, platinum, palladium, rhodium) as the active catalytic phase. Thus, the demand for PGMs is constantly increasing with a subsequent increase in their market prices. As a result, the research on catalytic converters of high activity and reduced cost/PGM loading is of great interest. In the present work, the Prometheus catalyst, a polymetallic nanosized copper-based catalyst for automotive emission control applications, is presented in two different metal loadings (2 wt% and 5 wt%) and metal ratios (Cu/Pd/Rh = 21/7/1 and Cu/Pd/Rh = 21/7/3). For the first time, a three-metal (copper, palladium, rhodium) nano-catalyst has been synthesized and characterized on a large scale. By using copper as an active catalytic phase, a reduction of PGMs loading is achieved (up to 85%) resulting in a novel catalytic device with similar or improved catalytic performance compared to commercial ones. The Prometheus catalyst is prepared by a wet impregnation method, using as a carrier an inorganic mixed oxide (CeZrO₄) exhibiting elevated oxygen storage capacity (OSC). The heterogeneous catalytic powders produced were characterized by both spectroscopic and analytical methods. The metal content and ratio were determined by inductively coupled plasma mass spectrometry (ICP-MS), X-ray fluorescence (XRF) and energy-dispersive X-ray spectroscopy (EDS). The morphology and the catalyst particle size were determined with scanning electron microscopy (SEM) and X-ray diffraction (XRD). The investigation revealed homogeneous particle formation and dispersion. The deposition of the metal nanoparticles on the porous inorganic carrier was verified with N₂ sorption. Catalytic performance and reactivity of a catalyst (pure wash coat) with molar ratio 21/7/1 and a full-scale Prometheus catalyst with the desired loading of 15 g/ft³ were tested on an in-house synthetic gas bench (SGB) for the abatement of CO, CH₄ and NO, both presenting high catalytic activity. Full article