Search Results (6)

This study introduces a novel, non-invasive X-ray absorption analysis (XRA) method to evaluate the photonic absorption process of granular activated carbon (GAC) in hospital water purification systems. By leveraging digital radiographic images, this innovative technique monitors the deterioration and oxidation of the GAC filter, predicts its remaining lifetime, and estimates its water dechlorinating capacity. Analyzing the entire GAC filter and making a reuse possible, the new XRA method provides valuable insights into the filter’s condition, enhancing water purification efficiency and costs without analyzing subsamples. Complementary analytical techniques on subsamples, taken at various depths, did not yield valuable additional information of the GAC filter exhaustion condition, nor additionally make a reuse impossible. Full article

This work investigates the impact of C-class solar flare events (XRA) on ionospheric and low-frequency signal propagation by analyzing the maximum correlation lag time, correlation, and Granger causality between low-frequency time-code signal strength and XRA. The results show that within the lag interval of (−5, 5) minutes, XRA exhibits the highest correlation and causality with signal strength, supporting the theory of a rapid ionospheric response and early warning to XRA. The correlation coefficient increases significantly with flare intensity, indicating that XRA has both linear and nonlinear dual effects on the disturbance of low-frequency signal propagation paths. Granger causality tests further confirm that XRA events have an immediate and sustained direct impact on signal strength. These findings provide a basis for understanding the disturbance mechanism of solar activity on the Earth’s ionosphere and support the use of low-frequency signals in space weather forecasting. Full article

Polymer matrix composites based on ED-20 epoxy resin, hollandite K_1.6(Ni_0.8Ti_7.2)O₁₆ and carbon nanotubes with a variable content of 0.107; 0.213 and 0.425 vol.% were obtained for the first time. Initial components and composites produced were characterized by XRD, XRA, FTIR, SEM and Raman spectroscopy. The dielectric properties of composite materials were measured by impedance spectroscopy and determined by the volume ratio of the composite components, primarily by the concentration of CNTs. At a CNT content of 0.213 vol.% (before percolation threshold), the maximum synergistic effect of carbon and ceramic fillers on the dielectric properties of a composite based on the epoxy resin was found. Three-phase composites based on epoxy resin, with a maximum permittivity at a minimum dielectric loss tangent, are promising materials for elements of an electronic component base. Full article

Fe-TiO₂/AC and Co-TiO₂/AC composites were prepared from activated carbon (AC) derived from residues of peanut hulls and TiO₂ photocatalyst, electrochemically prepared from titanium scrap, and doped with Fe and Co, respectively. The adsorption capacity and photocatalytic activity of the Fe-TiO₂/AC and Co-TiO₂/AC composites were studied for removing and degrading Cibacron Yellow F-4G (CYF-4G) from wastewater. Doped ACs were characterized by thermogravimetry (TGA), scanning electron microscopy (SEM), X-ray diffraction (XRD), a new X-ray absorption technique (XRA), and elemental analysis (EA). Interesting relationships were found between SEM, XRA, and TGA data and the doped amount of catalyst on ACs. Optimal dye adsorption was found at a pH of 2.0. The CYF-4G adsorption kinetics are followed according to the pseudo-second order model. The experimental data revealed that the Langmuir model fits better than the Freundlich and Temkin models. A decrease in adsorption capacity was observed when the catalyst dope percentage increased. A removal and degradation efficiency of the dye close to 100% was achieved around 120 min. A synergistic adsorption and photocatalytic degradation effect of the Fe-TiO₂/AC and Co-TiO₂/AC composites could be observed when adsorption experiments were conducted under simulated visible radiation. Full article

The X-ray absorption (XRA) method using digital image processing techniques is a reliable technique to determine the exhaustion degree of granular activated carbons (GACs). Using an innovative digital image processing technique, the identification of individual adsorbed molecules or ions in a GAC was possible. Adsorption isotherm models (Langmuir and Freundlich) were used to simulate the adsorption equilibrium data of Methylene Blue (MB), nickel, cobalt and iodine. Freundlich equation was found to have the highest value of R² compared with Langmuir. The identification of distinctive patterns applying XRA for different adsorbed ions and molecules onto GAC was explored. It is demonstrated that unique XRA configurations for each adsorbed ion or molecule are found, as well as a proportional relationship between its incident energy (needed to achieve maximum photon attenuation) and the (effective) atomic number, the adsorbate mass and the molar or atomic mass of adsorbed molecule or ion. XRA method in combination with image histogram modifications was used to obtain a digital signature of adsorbed ions/molecules, giving distinct GSI values for each one in the used energy range. Probabilistic models prove that XRA results are within relationships between effective atomic number and photonic interaction probability, reinforcing the potentialities of XRA for monitoring (multi-)ion and/or molecule combinations on GAC using advanced digital image processing techniques. It was proved that the proposed approach could assess different adsorbed ions/molecules onto GACs in water purification systems. Full article

The stability and reusability of soluble enzymes are of major concerns, which limit their industrial applications. Herein, alkaline protease from Bacillus sp. NPST-AK15 was immobilized onto hollow core-mesoporous shell silica (HCMSS) nanospheres. Subsequently, the properties of immobilized proteases were evaluated. Non-, ethane- and amino-functionalized HCMSS nanospheres were synthesized and characterized. NPST-AK15 was immobilized onto the synthesized nano-supports by physical and covalent immobilization approaches. However, protease immobilization by covalent attachment onto the activated HCMSS–NH₂ nanospheres showed highest immobilization yield (75.6%) and loading capacity (88.1 μg protein/mg carrier) and was applied in the further studies. In comparison to free enzyme, the covalently immobilized protease exhibited a slight shift in the optimal pH from 10.5 to 11.0, respectively. The optimum temperature for catalytic activity of both free and immobilized enzyme was seen at 60 °C. However, while the free enzyme was completely inactivated when treated at 60 °C for 1 h the immobilized enzyme still retained 63.6% of its initial activity. The immobilized protease showed higher V_max, k_cat and k_cat/K_m, than soluble enzyme by 1.6-, 1.6- and 2.4-fold, respectively. In addition, the immobilized protease affinity to the substrate increased by about 1.5-fold. Furthermore, the enzyme stability in various organic solvents was significantly enhanced upon immobilization. Interestingly, the immobilized enzyme exhibited much higher stability in several commercial detergents including OMO, Tide, Ariel, Bonux and Xra by up to 5.2-fold. Finally, the immobilized protease maintained significant catalytic efficiency for twelve consecutive reaction cycles. These results suggest the effectiveness of the developed nanobiocatalyst as a candidate for detergent formulation and peptide synthesis in non-aqueous media. Full article