Search Results (283)

This systematic review presents a critical analysis of multifunctional nanowire sensors, with explicit selection criteria for included studies: we focus on peer-reviewed research, prioritizing studies on semiconductor (ZnO, TiO₂, Si), metal (Ag, Au), and carbon-based (CNT) nanowires that report structural innovations, performance breakthroughs, or industrial scalability. We systematically analyze their structural characteristics, advanced fabrication techniques (hydrothermal synthesis, magnetron sputtering, PECVD), and application performance across biosensing, pressure sensing, and gas monitoring. Unlike existing reviews limited to single material classes or application scenarios, this work advances the field by integrating three novel perspectives: it delivers a cross-material comparison of nanowire structure–performance relationships, incorporates an analysis of fabrication strategy scalability for industrial translation, and synthesizes unresolved challenges and future directions. Nanowire sensors exhibit superior sensitivity, rapid response, and broad detection ranges compared to conventional sensors, with significant potential to advance healthcare, environmental monitoring, and flexible electronics. Full article

The efficient removal of toxic dyes from wastewater remains a major environmental challenge. In this study, we report a green and facile one-pot synthesis of zinc oxide nanowires (ZnO-NWs) using lemon verbena leaf extract as a sustainable capping and stabilizing agent. The extract played a vital role in directing the 1D growth of the wurtzite hexagonal structure. Characterization confirmed a band gap of 3.12 eV and the characteristic Zn-O stretching at 375 cm⁻¹. Photocatalytic activity tests using 20 mg of biosynthesized ZnO-NWs demonstrated excellent degradation performance. A rate constant of 0.0067 min⁻¹ was achieved, with 99.95% degradation of Basic Fuchsin under natural sunlight for 3 h. Active species analysis highlighted the crucial roles of holes (h⁺), superoxide radicals (O₂•⁻), and hydroxyl radicals (•OH). Notably, the addition of 10 mM H₂O₂ produced a powerful synergistic effect, reducing the degradation time from 3 h to only 7 min and increasing the reaction rate by approximately 25-fold. These findings highlight the potential of biosynthesized ZnO-NWs as highly efficient, rapid, and sustainable photocatalysts for environmental remediation. Full article

In this paper, composite structures were fabricated by incorporating silver nanowires (AgNWs) with various metal oxides via the sol–gel method. This approach enhanced the electrical performance of AgNW-based transparent electrodes while simultaneously improving their stability under damp heat conditions and modifying the local medium environment surrounding the AgNW meshes. The randomly distributed AgNW meshes fabricated via drop-coating were treated with plasma to remove surface organic residues and reduce the inter-nanowire contact resistance. Subsequently, a zinc oxide (ZnO) coating was applied to further decrease the sheet resistance (R_sheet) value. The pristine AgNW mesh exhibits an R_sheet of 17.4 ohm/sq and an optical transmittance of 93.06% at a wavelength of 550 nm. After treatment, the composite structure achieves a reduced R_sheet of 8.7 ohm/sq while maintaining a high optical transmittance of 92.20%. The use of AgNW meshes as window electrodes enhances electron injection efficiency and facilitates the coupling mechanism between localized surface plasmon resonances and excitons. Compared with conventional ITO transparent electrodes, the incorporation of the AgNW mesh leads to a 17-fold enhancement in ZnO emission intensity under identical injection current conditions. Moreover, the unique scattering characteristics of the AgNW and metal oxide composite structure effectively reduce photon reflection at the device interface, thereby broadening the angular distribution of emitted light in electroluminescent devices. Full article

One-dimensional ZnO nanowires offer significant potential for optoelectronic applications, though their controlled synthesis remains challenging. This study optimized ZnO nanowire growth via carbothermal reduction vapor transport based on the vapor–liquid–solid mechanism. Key parameters investigated were gold catalyst thickness and annealing, source temperature, system pressure, and oxygen concentration. Results show that thinner Au films promote high-density, small-diameter nanowires. An optimal source temperature window (950–1000 °C) was identified, while pressure and oxygen content critically influenced growth mode by modulating vapor supersaturation. Under optimized conditions, aligned single-crystalline ZnO nanowires with hexagonal wurtzite structure were achieved. Structural and optical characterization confirmed high crystallinity and strong near-band-edge emission, demonstrating the efficacy of the developed approach for tailored nanowire synthesis. Full article

The continuous advancement of modern weaponry has intensified the pursuit of next-generation ballistic protection systems that integrate lightweight architectures, superior flexibility, and high energy absorption efficiency. This review provides a technological overview of current trends in the design, processing, and performance optimization of metallic, ceramic, polymeric, and composite materials for ballistic applications. Particular emphasis is placed on the role of advanced surface coatings and nanostructured interfaces as enabling technologies for improved impact resistance and multifunctionality. Conventional materials such as high-strength steels, alumina, silicon carbide, boron carbide, Kevlar^®, and ultra-high-molecular-weight polyethylene (UHMWPE) continue to dominate the field due to their outstanding mechanical properties; however, their intrinsic limitations have prompted a transition toward nanotechnology-assisted solutions. Functional coatings incorporating nanosilica, graphene and graphene oxide, carbon nanotubes (CNTs), and zinc oxide nanowires (ZnO NWs) have demonstrated significant enhancement in interfacial adhesion, inter-yarn friction, and energy dissipation. Moreover, multifunctional coatings such as CNT- and laser-induced graphene (LIG)-based layers integrate sensing capability, electromagnetic interference (EMI) shielding, and thermal stability, supporting the development of smart and adaptive protection platforms. By combining experimental evidence with computational modeling and materials informatics, this review highlights the technological impact of coating-assisted strategies in the evolution of lightweight, high-performance, and multifunctional ballistic armor systems for defense and civil protection. Full article

Zinc oxide nanowires are often used to improve the bulletproof performance of high-performance fabrics, but determining the coefficients of inter-yarn friction (CIFs) of those fabrics in numerical ballistic models is a challenge. In this article, the linear method is adopted to obtain the CIF of sateen fabrics with two thread densities treated with zinc oxide nanowires. For treated sateen fabrics with a thread density of 8 ends/cm (S-8-ZnO), the coefficient of static friction (CSF) and coefficient of kinetic friction (CKF) obtained by the linear method are 1.85 and 1.83, respectively. For treated sateen fabrics with a thread density of 13 ends/cm (S-13-ZnO), the CSF and CKF obtained by the linear method are 0.76 and 0.74, respectively. The obtained coefficients are input into the yarn pull-out models of the above two types of sateen fabrics. It is found that for both S-8-ZnO and S-13-ZnO fabrics, the errors of the yarn pull-out force by the linear method are 0.43% and 6.56%, respectively. The method presented in this study provides a more feasible approach for determining the CIF of chemically treated fabrics in future FE simulations. Full article

The chemical bath deposition of ZnO nanowires is of high interest for many functional devices, but the typical use of hexamethylenetetramine (HMTA) molecules forming formaldehyde as a harmful substance raises health, environment, and regulation issues. After a careful review of the multiple roles of HMTA molecules, we unambiguously show, using X-ray near-edge structure absorption spectroscopy with synchrotron radiation, that they do not form any complexes with the Zn(II) species, both in the low- and high-pH regions. In contrast and in agreement with thermodynamic computations, [Zn(H₂O)₆]²⁺ and Zn(NH₃)₄²⁺ ion complexes are revealed to be the predominant Zn(II) species in the low- and high-pH regions. The use of HMTA molecules is found to be critical to form ZnO nanowires with a high aspect ratio in the low-pH region. In contrast, HMTA molecules are shown to be fully substituted by ammonia in the high-pH region to form ZnO nanowires with a high structural and optical quality. The removal of HMTA molecules for the chemical bath deposition of ZnO nanowires in the high-pH region represents a significant step forward towards the development of a chemical synthesis fully compatible with green chemistry. Full article

In this study we report on the structural, mechanical, and electrical characterization of different structures of vertically aligned zinc oxide (ZnO) nanowires (NWs) synthesized using hydrothermal methods. By optimizing the growth conditions, scanning electron microscopy (SEM) micrographs show that the ZnO NWs could reach an astounding 51.9 ± 0.82 µm in length, 0.7 ± 0.08 µm in diameter, and 3.3 ± 2.1 µm⁻² density of the number of NWs per area within 24 h of growth time, compared with a reported value of ~26.8 µm in length for the same period. The indentation modulus of the as-grown ZnO NWs was determined using contact resonance (CR) measurements using atomic force microscopy (AFM). An indentation modulus of 122.2 ± 2.3 GPa for the NW array sample with an average diameter of ~690 nm was found to be close to the reference bulk ZnO value of 125 GPa. Furthermore, the measurement of the piezoelectric coefficient (d₃₃) using the traceable ESPY33 tool under cyclic compressive stress gave a value of 1.6 ± 0.4 pC/N at 0.02 N with ZnO NWs of 100 ± 10 nm and 2.69 ± 0.05 µm in diameter and length, respectively, which were embedded in an S1818 polymer. Current–voltage (I-V) measurements of the ZnO NWs fabricated on an n-type silicon (Si) substrate utilizing a micromanipulator integrated with a tungsten (W) probe exhibits Ohmic behavior, revealing an important phenomenon which can be attributed to the generated electric field by the tungsten probe, dielectric residue, or conductive material. Full article

The study of the processes of low-temperature synthesis of one-dimensional particles, which are the basis for two- and three-dimensional structures, is relevant for materials science. The modified metal-stimulated electrochemical etching method made it possible to synthesize silicon nanowires with an average thickness of about 292.6 nm. Scanning electron microscopy has shown the formation of nanowires, flower-like structures, and clusters of matter after the deposition of zinc oxide on the porous surface. The hexagonal structure of ZnO crystallites was determined by X-ray diffraction spectroscopy. Studies of the initial sample by electron paramagnetic resonance (EPR) spectroscopy revealed a narrow signal in the center of the spectrum. The subtraction of the EPR spectra with a sequential increase in microwave power up to 8 mW shows the absence of saturation of the signal. This indicates an almost free flow of charges through the surface nanostructures under the influence of an external field. Heat treatment in an air atmosphere at 300 °C caused a significant increase in the intensity of the EPR spectrum. This led to an increase in the intensity of charge transfer through paramagnetic centers. Full article

Hexagonal ZnO nanowires were grown using the PLD/VLS technique on a SAW sensor active area for hydrogen sensing. The influence of different carbon and nitrogen surface contaminant concentrations on sensor output was investigated for three active area cases: a few weeks’ exposure to free ambient air contamination, 3 h at 600 °C thermal desorption of carbon, and (room temperature) plasma-activated nitrogen and carbon contamination. Correlations between sensing performance and contamination element concentration were established. To understand the adsorption versus absorption mechanisms, similar studies were further performed on circular ZnO nanowires morphology, which have a different surface-area-to-volume ratio. Comparative results show that, while a 20% carbon surface contamination variation generates a variation of 3–5% in nanostructure hydrogen sorption, nitrogen surface contamination influence depends on nanostructure morphology. Thus, in our comparative studies, for the case of a nanowire hexagonal cross-section a 12% nitrogen surface contamination variation generates a 5–7% increase in hydrogen adsorption and also an increase of 6–8% in hydrogen absorption. Consequently, the catalytic effect of nitrogen could enlarge the linear response of nanowire-based (SAW) sensors over a wider hydrogen concentration range. Full article

The development of state-of-the-art gas sensors based on metal oxide semiconductors (MOS) to monitor hazardous and greenhouse gas (e.g., methane, CH₄, and carbon dioxide, CO₂) has been significantly advanced. Moreover, the morphological and topographical structures of MOSs have significantly influenced the gas sensors by means of surface catalytic activities. This work examines the impact of morphological and topological networked assembly of zinc oxide (ZnO) nanostructures, including microparticles and nanoparticles (0D), nanowires and nanorods (1D), nanodisks (2D), and hierarchical networks of tetrapods (3D). Gas sensors consisting of vertically aligned ZnO nanorods (ZnO–NR) and topologically interconnected tetrapods (T–ZnO) of varying diameter and arm thickness synthesized using aqueous phase deposition and flame transport method on interdigitated Pt electrodes are evaluated for methane detection. Smaller-diameter nanorods and tetrapod arms (nanowire-like), having higher surface-to-volume ratios with reasonable porosity, exhibit improved sensing behavior. Interestingly, when the nanorods’ diameter and interconnected tetrapod arm thickness were comparable to the width of the depletion layer, a significant increase in sensitivity (from 2 to 30) and reduction in response/recovery time (from 58 s to 5.9 s) resulted, ascribed to rapid desorption of analyte species. Additionally, nanoparticles surface-catalyzed with Pd (~50 nm) accelerated gas sensing and lowered operating temperature (from 200 °C to 50 °C) when combined with UV photoactivation. We modeled the experimental findings using a modified general formula for ZnO methane sensors derived from the catalytic chemical reaction between methane molecules and oxygen ions and considered the structural surface-to-volume ratios (S/V) and electronic depletion region width (L_d) applicable to other gas sensors (e.g., SnO₂, TiO₂, MoO₃, and WO₃). Finally, the effects of UV light excitation reducing detection temperature help to break through the bottleneck of ZnO-based materials as energy-saving chemiresistors and promote applications relevant to environmental and industrial harmful gas detection. Full article

With growing environmental concerns and the need for sustainable energy, multifunctional materials that can simultaneously address water treatment and clean energy production are in high demand. In this study, we developed a cost-effective method to synthesize zinc oxide (ZnO) nanowires via the anodic oxidation of zinc foil. By carefully controlling the anodization time, we optimized the Zn/ZnO-5 min electrode to achieve impressive dual-function performance in terms of effective photoelectrocatalysis for water splitting and waste water treatment. The electrode exhibited a high photocurrent density of 1.18 mA/cm² at 1.23 V vs. RHE and achieved a solar-to-hydrogen conversion efficiency of 0.55%. A key factor behind this performance is the presence of surface defects, such as oxygen vacancies (OVs), which enhanced charge separation and boosted electron transport. In tests for waste water treatment, the Zn/ZnO-5 min electrode demonstrated the highly efficient degradation of methylene blue (MB) dye, with a reaction rate constant of 0.4211 min⁻¹ when exposed to light and a 1.0 V applied voltage significantly faster than using light or voltage alone. Electrochemical analyses, including impedance spectroscopy and voltammetry, further confirmed the superior charge transfer properties of the electrode under illumination, making it an excellent candidate for both energy conversion and pollutant removal. This study highlights the potential of using simple anodic oxidation to produce scalable and efficient ZnO-based photocatalysts. The dual-function capability of this material could pave the way for large-scale applications in renewable hydrogen production and advanced waste water treatment, offering a promising solution to some of today’s most pressing environmental and energy challenges. Full article

The burgeoning field of biosensors has seen significant advancements with the induction of zinc oxide (ZnO) nanostructures, because of their unique structural, electrical, and optical properties. ZnO nanostructures provide numerous benefits for biosensor applications. Their superior electron mobility enables effective electron transfer between the bioreceptor and transducer, enhancing sensitivity and reducing detection limits. Furthermore, ZnO’s biocompatibility and non-toxicity make it ideal for in vivo applications, reducing the chances of adverse biological responses. This review paper explores the prospects of ZnO nanostructures in the development of biosensors, focusing on their morphological and structural characteristics. Various synthesis techniques, that include sol-gel, sputtering, and chemical vapor deposition, were successfully employed to prepare different ZnO nanostructures, like nanorods, nanotubes, and nanowires. The various findings in this field underscore the efficacy of ZnO nanostructures in enhancing the specificity and sensitivity of biosensors, presenting a promising avenue for the advancement of point-of-care diagnostic devices. Full article

Neuromorphic computing, inspired by the brain, holds significant promise for advancing artificial intelligence. Artificial optoelectronic synapses, which can convert optical signals into electrical signals, play a crucial role in neuromorphic computing. In this study, we successfully fabricated a flexible artificial optoelectronic synapse device based on the ZnO/PDMS structure by utilizing the magnetron sputtering technique to deposit the ZnO film on a flexible substrate. Under UV light illumination, the device exhibits excellent synaptic plasticity, including excitatory postsynaptic current (EPSC), short-term potentiation (STP), and paired-pulse facilitation (PPF). By growing ZnO nanowires, we improved the fabrication processes and further enhanced the synaptic properties of the device, demonstrating long-term potentiation (LTP) and the transition from short-term memory (STM) to long-term memory (LTM). Additionally, the device exhibits outstanding flexibility, maintaining stable synaptic plasticity under bending conditions. This device shows broad application potential in mimicking visual systems and is expected to contribute significantly to the development of neuromorphic computing. Full article

The structural characteristics of electrode materials play a crucial role in their potential applications. Therefore, designing the material’s structure rationally is one of the most effective methods to achieve high-performance electrodes. In this study, V−ZnCo₂O₄ nanowires were synthesized on nickel foam using a simple hydrothermal method, and the prepared V−ZnCo₂O₄−2 electrode material exhibited a specific capacitance of 1621 C g⁻¹. The potential applications of the prepared material were evaluated through device assembly, using V−ZnCo₂O₄−2 as the positive electrode and activated carbon as the negative electrode. The resulting device delivered an energy density of 127.5 Wh/kg, with a corresponding power density of 2700 W/kg. Additionally, the mechanical properties of the device were assessed, revealing that after multiple bends at different angles, the shape of the device remained well-preserved, further confirming its excellent mechanical stability. Full article