Search Results (1,069)

Because of its specific nature, mining activity causes numerous negative impacts on the environment, both during the exploitation phase and after it has ended. An important source of income in the Jiu Valley is represented by the Lupeni Mining Exploitation. Like any mining activity, coal exploitation causes various negative effects on the environment. The subsidence phenomenon represents a significant issue associated with coal mining in the Jiu Valley. Underground extraction of mineral deposits induces displacement of the overburden strata. Such displacements result in ground subsidence and modifications of the surface topography. The larger the voids created following the exploitation of useful mineral deposits, the more they affect the surface of the land above the exploitation through sinking, displacement, deformation, and even cracks. Secondary deformations refer to post-mining surface movements induced by delayed rock mass adjustment, manifesting as ground collapse, localized subsoil failure, or uplift driven by groundwater rebound after drainage cessation. In this paper, we aim to study the subsidence phenomenon produced by coal mining at the Lupeni Mining Exploitation using the COMSOL simulation software and applying the Barcelona Basic Model (BBM) and Modified Cam-Clay (MCC) models. Following the simulation, the behavior of the rocks could be observed in order to improve prediction accuracy to support sustainable land management in post-mining areas. Full article

This research is to assess the potential use of phosphate sludge from the Gafsa (Tunisia) phosphate laundries as an alternative raw material for the manufacture of ecological refractory bricks. Feasibility was evaluated through comprehensive physico-chemical and mineralogical characterizations of the raw materials using X-ray diffraction (XRD), X-ray fluorescence (XRF), Fourier-transform infrared spectroscopy (FTIR), and thermal analysis (TGA-DTA). Bricks were formulated by substituting phosphate sludge with clay and diatomite, then activated with potassium silicate solution to produce geopolymeric materials. Specific formulations exhibited mechanical performance ranging from 7 MPa to 26 MPa, highlighting the importance of composition and minimal water absorption values of approximately 17.8% and 7.7%. The thermal conductivity of the bricks was found to be dependent on the proportions of diatomite and clay, reflecting their insulating potential. XRD analysis indicated the formation of an amorphous aluminosilicate matrix, while FTIR spectra confirmed the development of new chemical bonds characteristic of geopolymerization. Thermal analysis revealed good stability of the materials, with mass losses mainly related to dehydration and dehydroxylation processes. Environmental assessments showed that most samples are inert or non-hazardous, though attention is required for those with elevated chromium content. Overall, these findings highlight the viability of incorporating phosphate sludge into fired brick production, offering a sustainable solution for waste valorization in accordance with the circular economy. Full article

The results from previous environmental studies on the physicochemical properties of bottom sediments from the Odra River estuary (SW Baltic Sea) and their contamination by pharmaceutically active compounds (PhACs) were compiled and analyzed by the use of various statistical methods (Principal Component Analysis, ANOVA/Kruskal–Wallis, Spearman correlation analysis, Partial Least Squares Discriminant Analysis, and Cluster Analysis). These studies included data on 130 PhACs determined in sediment samples collected from 70 sites across the Odra River estuary as well as the site distance to wastewater treatment plant discharge, PhACs’ physicochemical properties (Kd, Kow, pKa, solubility, metabolism), and sales data. Additionally, total organic carbon, total nitrogen, total phosphorus, acid volatile sulfides, clay mineral content, and trace elements such as As, Ba, Cd, Co, Cr, Cu, Fe, Hg, Mn, Mo, Ni, Pb, Sn, and Zn were analyzed. Clay mineral content and TP were identified as the key physicochemical factors influencing the spatial distribution of PhACs in bottom sediments, exerting a greater impact than the distance of sampling sites from WWTP discharge points. The distribution of PhACs in the estuary was also influenced by the Kd and solubility of the compounds. More soluble pharmaceuticals with low adsorption affinity to sediments were detected more frequently and transported to distant locations, whereas less soluble compounds with high adsorption affinity settled down in bottom sediments near contamination sources. Neither the proportion of a drug excreted unchanged, nor its prescription frequency and sales volume, influenced the spatial distribution of PhACs. In general, Kd may be a useful parameter in the planning of environmental monitoring and tracing migration of PhACs in aquatic environments. Full article

The diversification of cover crops grown in soils with granulometric variability may potentially enhance microbial community and enzyme activities. Thus, the main goal was to evaluate the effect of autumn/winter cover crop sequences and cash crops in spring/summer on soil microbial biomass and enzyme activities. The experiment was conducted in open-field microplots (10 m × 1 m × 0.7 m), containing soils from B horizon of five Oxisols with granulometric variability and clay content ranging from 17 to 80 dag kg⁻¹. The treatments were three cover crops and a winter fallow with a completely randomized experimental design with three replicates. Soil samples from the 0–10 cm layer were collected to analyze soil microbial biomass of carbon and nitrogen, enzyme activities of the acid phosphatase, arylsulfatase, urease, and fluorescein diacetate hydrolysis. The number of nodules in soybean roots was average 63 ± 14.42 nodules per plant and dry mass of nodules was 169 ± 13.74 mg plant⁻¹. Soybean nodulation and N uptake ensured the supply of nitrogen to the soybean plants with 331 ± 82 mg plant⁻¹. Overall, diversified autumn/winter cover crop sequences provide plant residue, containing nutrients, and different carbon/nitrogen, which alters microbial biomass, the ratio of C_mic/N_mic, basal respiration, and soil enzyme activities within each Oxisol with different particle size distribution. Full article

This work examines the colloidal properties of clays sampled from two different locations in Ventzia basin processed as low-density solid additives for water-based drilling fluid applications. The obtained samples were mechanically processed to reach a size less than 2 cm. The material was then activated with 3 wt% soda ash without oven drying, keeping the moisture in environmental conditions to simulate industrial activation conditions. After laying for one month curing time, samples were oven dried at 60 °C and further ground to <120 μm. Two groups of samples were created mixing clays from Ventzia basin and additives. The first group contained clay, xanthan gum and sodium polyacrylate (PAA), while the second group contained clay, xanthan gum and sodium hexametaphosphate (SHMP). Standard tests were performed for the rheological behavior and filtration properties prior to and after dynamic thermal aging. Results obtained were compared with commercial clays from Milos and Wyoming used in drilling fluid systems, after thermally deteriorating also their properties. The obtained results revealed that the enhanced clays under study maintain excellent thermal stability. Notably, the top-performing formulation met the critical American Petroleum Institute (API) benchmark for filtrate loss (<15 mL) and exhibited a robust rheological profile at temperatures up to 105 °C, demonstrating its suitability for water-based fluid (WBF) applications. Full article

Straw return is essential for improving soil fertility, recycling organic matter, and sustaining productivity in rice–wheat systems. This study focuses on the conceptual design and systematic analysis of the spatial and temporal variability of straw return methods and their classification. We proposed and analyzed 36 technical models for straw return by integrating spatial distribution (depth and horizontal placement) with temporal variability (decomposition period managed through mulching or decomposers). The models of straw return were categorized into five classes: mixed burial, even spreading, strip mulching, deep burial, and ditch burial. Field experiments were conducted in Babaiqiao Town, Nanjing, China, using clay loam soils typical of intensive rice–wheat rotation. Soil properties (bulk density, porosity, and moisture content) and straw characteristics (length and density) were evaluated to determine their influence on decomposition efficiency and nutrient release. Results showed that shallow incorporation (0–5 cm) accelerated straw breakdown and microbial activity, while deeper incorporation (15–20 cm) enhanced long-term organic matter accumulation. Temporal control using mulching films and decomposer agents further improved moisture retention, aeration, and nutrient availability. For the rice–wheat system study area, four typical straw return modes were selected based on spatial distribution and soil physical parameters: straw even spreading, rotary plowing, conventional tillage with mulching, and straw plowing with burying. This study added to the growing body of literature on straw return by providing a systematic analysis of the parameters influencing straw decomposition and the incorporation. The results have significant implications for sustainable agricultural practices, offering practical recommendations for optimizing straw return strategies to improve soil health. Full article

Ceramic membrane technology plays an important role in water and wastewater treatment. Strategic sourcing of various natural mineral resources has contributed to developing low-cost ceramic membranes. The combination with calcination of inorganic and organic wastes from domestic and agricultural activities results in fully sustainable ceramic membrane materials. In this work, ceramic membranes were developed using 96% clay, 2% almond shells and 2% lime. Sintering at 900, 950, and 1000 °C enabled the production of membranes (MK-900, MK-950, and MK-1000) in a clean, simple, and cost-effective manner. The average pore diameter and porosity decreased slightly from 44 to 42 nm and from about 30% to 26% with increasing sintering temperature, while the flexural strength increased from 25 to 40 MPa. The pure water permeability was 68 and 59 L·m⁻²·h⁻¹·bar⁻¹ for MK-900 and MK-950, respectively. Effective color (as Indigo blue) removal of 78% and 92% was observed for MK-900 and MK-950, respectively. More than 90% of the initial permeability was recovered after three cycles of dye filtration using water backwashing at each stage, indicating good fouling resistance of the prepared membranes. Full article

During the development of metallurgical technology in the feudal period, the main ironmaking technology in the Benxi region was the crucible, reaching its peak period in the Ming Dynasty. By studying the Wangguan ironmaking site in Benxi, the historical details of the Ming Dynasty ironmaking process in the region were investigated, and a technical analysis was carried out. The results show that this historical site was the location of the Hundred-Household Iron Yard in the northeastern region during the Ming Dynasty. The unearthed slag, iron, and crucible samples indicate that a relatively complete ironmaking process chain had been formed at this time. The raw material used for the crucibles was high-alumina clay, which has been widely distributed in Benxi, Liaoning, China, since ancient times. The refractoriness of the crucibles exceeded 1700 °C, and the molar ratio of SiO₂ to Al₂O₃ was close to the upper limit for the optimal formation of mullite and thermal shock resistance. Slag was produced from a typical high-silica, high-alumina aluminosilicate system, and no fluxes, such as limestone and dolomite, were added during the smelting process. Moreover, coal resources have been widely used in ironmaking activities in the Benxi region at least since the Ming Dynasty, and craftsmen at that time had already mastered the technology of using coke as fuel and reductant to control the sulfur content in pig iron. Full article

Clay-rich soils are stabilized using fly ash, cement, lime, or solid waste with chemical activators to improve strength and reduce moisture-induced settlement. This study explores the stabilization of clay using lime and dried solid digestate (DSD) derived from food waste to improve its strength. A clay sample was treated with varying proportions of DSD (1–5%) along with 4.5% lime, by dry weight of soil. Samples were compacted at optimum moisture content and cured for periods of 0, 7, 14, and 28 days. The improvement in geotechnical behavior was assessed through Atterberg limits, unconfined compressive strength (UCS), and microscopic analyses, including X-ray diffraction (XRD), scanning electron microscopy (SEM), and Fourier-transform infrared spectroscopy (FTIR). Compared with untreated clay (62.03 kPa), the results show that adding 2% DSD and lime significantly increased compressive strength (446.5 kPa) and decreased plasticity by 69%. X-ray fluorescence (XRF) analysis revealed that the lime contained 81% of high calcium oxide (CaO), which supports pozzolanic and carbonation processes, whereas DSD served as a supplementary additive. Hence, the integration of DSD in soil stabilization offers a dual benefit: enhancing geotechnical performance and promoting environmental sustainability by diverting food waste from landfills and supporting circular resource use. Full article

Mineral oil-based lubricants contain harmful elements, such as sulfur and phosphorus, pose significant harm to the environment. In current research on the application of waste oils and fats in bio-based lubricants, most studies focus on single pretreatment processes or additive preparation, lacking systematic investigations into the combined use of composite pretreatment and additives on lubricant performance. Moreover, the decolorization efficiency of traditional physical adsorption methods for treating waste oils and fats is limited, making it difficult to meet the raw material requirements for bio-based lubricants. The purpose of this study is to conduct composite pretreatment processes on waste oils and fats, understand the impacts of parameters such as additive dosage and environmental factors on lubricant performance, establish an environmentally friendly and performance-compliant preparation process for bio-based lubricants, and provide a theoretical basis and technical support for its industrial application. Recent studies have shown that new decolorization processes for waste oil treatment significantly improve decolorization and recovery rates, as evidenced by research comparing new and traditional methods. Pretreatment with hydrogen peroxide, activated clay, and activated carbon significantly improved the color and odor of treated waste oil, meeting standards for bio-based lubricant production. The intercalation polymerization reaction between ethyl cellulose (EC) and montmorillonite (MMT) was employed to develop an additive (CTAB-MMT/KH560-EC). A thorough investigation was performed to analyze the impact of temperature, processing time, and additive concentration on the rheological behavior. The bio-based lubricant exhibited a kinematic viscosity of 200.3 mm²/s at 40 °C and 28.3 mm²/s at 100 °C, meeting the standard conditions as outlined in ASTM D2270-10e1. This lubricant achieved an improved low-temperature performance with a pour point of −22 °C, a friction coefficient of 0.081, and an average pitting diameter of 0.94 mm, indicating its suitability for a range of applications. These lubricants exhibit outstanding viscosity characteristics, meeting the relevant requirements for energy and environmental applications in green, eco-friendly, and biodegradable sustainable development strategies while expanding their application scope. Full article

Water pollution continues to pose a critical global challenge, largely due to the unregulated discharge of industrial, agricultural, and municipal effluents. Among emerging solutions, enzymatic bioremediation stands out as a sustainable and environmentally friendly approach, offering high specificity and efficiency under mild conditions. Nonetheless, the practical application of free enzymes is hindered by their inherent instability, poor reusability, and susceptibility to denaturation. To address these limitations, the immobilization of enzymes onto solid supports, particularly clay minerals, has garnered increasing attention. This review presents a detailed analysis of clay minerals as promising carriers for enzyme immobilization in wastewater treatment. It explores their classification, structural characteristics, and physicochemical properties, highlighting key advantages such as a large surface area, cation exchange capacity, and thermal stability. Functionalization techniques, including acid/base activation, intercalation, grafting, and pillaring, are discussed in terms of improving enzyme compatibility and catalytic performance. Various immobilization methods such as physical adsorption, covalent bonding, entrapment, crosslinking, and intercalation are critically evaluated with regard to enhancing enzyme activity, stability, and recyclability. Recent case studies demonstrate the effective removal of pollutants such as dyes, pharmaceuticals, and heavy metals using enzyme–clay composites. Despite these advances, challenges such as enzyme leaching, mass transfer resistance, and variability in clay composition persist. This review concludes by outlining future prospects, including the development of hybrid and magnetic clay-based systems and their integration into advanced water treatment technologies. Overall, enzyme immobilization on clay minerals represents a promising and scalable approach for the next generation of wastewater bioremediation strategies. Full article

Studies of early syn-rift successions in the Duwi Basin have revealed repetitive lacustrine carbonate deposits exhibiting regressive sequences and early diagenetic processes. Two main informal stratigraphic units (Units 1 and 2), spanning the Late Oligocene to Early Miocene, have been identified in the area. Unit 1 primarily consists of lacustrine limestone and calcrete deposits that formed in a palustrine environment, whereas Unit 2 is composed of dolomites and cherts, which developed during times of lake evaporation and desiccation under arid climatic conditions. A wide variety of pedogenic features, including brecciation, nodulization, rhizocretions, fissuring, microkarsts, and circumgranular cracks, dominate the carbonate sequence, indicating deposition in a marginal lacustrine setting. Integrated petrographic, mineralogical, geochemical, and isotopic studies of carbonate facies reveal two distinct evolutionary stages in the Duwi Basin, with dolomitization and silicification characterizing the late stage. Their isotopic compositions show a wide range of δ¹³C and δ¹⁸O values, ranging from −9.00‰ to −7.98‰ and from −10.03‰ to −0.68‰, respectively. Dolomite beds exhibit more negative δ¹³C and δ¹⁸O values, whereas palustrine limestones display higher (less negative) values. The upward trend of δ¹⁸O enrichment in carbonates suggests that the lake became hydrologically closed. Trace element concentrations serve as potential markers for distinguishing carbonate facies, aiding with paleoenvironmental and diagenetic interpretations. Our findings indicate that the studied dolomites and cherts formed under both biogenic and abiogenic conditions in an evaporative, alkaline-saline lake system. Biogenic dolomite and silica likely resulted from microbial activity, whereas abiogenic formation was driven by physicochemical conditions, including decreasing pH values and the presence of smectite clays. Tectonics, local climate, and provenance played crucial roles in controlling the overall diagenetic patterns and evolutionary history of the lake basin system during the Late Oligocene to Early Miocene. Full article

Cyanobacteria are a natural source of bioactive compounds increasingly recognized for their anti-inflammatory properties. In the Euganean Thermal District (Italy), thermal muds, used to cure arthro-rheumatic diseases, are prepared using natural clay and thermal water, resulting in a mature mud characterized by a complex microbial biofilm dominated by Cyanobacteria. Among these, Phormidium sp. ETS-05 has been shown to contribute to the therapeutic properties of the mud, mainly through the production of bioactive compounds such as exopolysaccharides (EPSs) and glycoglycerolipids (GLs). In contrast, the role of biomolecules from Thermospirulina andreolii ETS-09 and Kovacikia euganea ETS-13, also abundant in mature muds but at higher maturation temperatures, has not been investigated. This study focuses on the lipid profiles of these cyanobacteria, cultivated under temperature conditions that mimic their natural environment and that are different for the three species. Lipid extracts were analyzed for GLs classes and fatty acid composition, and their anti-inflammatory potential was assessed in vivo using a zebrafish inflammation model. All extracts showed anti-inflammatory activity with Phormidium sp. ETS-05 displaying the highest lipid content and the most rapid and potent beneficial effect, likely due to the specific composition of its GLs, presenting the greatest abundance of polyunsaturated fatty acids. These findings provide new insights into the biological basis of the therapeutic effects of Euganean muds and emphasize the importance of maturation conditions for cyanobacterial growth and bioactive lipid production. Full article

Restoration plantations in subtropical regions, often established with fast-growing tree species such as Acacia auriculiformis A. Cunn. ex Benth and Eucalyptus urophylla S. T. Blake, are frequently developed on highly weathered soils characterized by phosphorus deficiency. To investigate strategies for mitigating nutrient imbalances in such ecosystems, a long-term (≥13 years) fertilization experiment was designed. The experiment involved three fertilization regimes: nitrogen fertilizer alone (N), phosphorus fertilizer alone (P), and a combination of nitrogen and phosphorus (NP) fertilizers. The objective of this study was to investigate the effects of long-term fertilization practices on soil quality in subtropical plantations using a soil quality index (SQI). Consequently, all conventional soil physical, chemical, and biological indicators associated with the SQI responses to long-term fertilization treatments were systematically evaluated, and a principal component analysis (PCA) was conducted, along with a literature review, to develop a minimum dataset (MDS) for calculating the SQI. Three physical indicators (silt, clay, and soil water content), three chemical indicators (soil organic carbon, inorganic nitrogen, and total phosphorus), and two biological indicators (microbial biomass carbon and phosphodiesterase enzyme activity) were finally chosen for the MDS from a total dataset (TDS) of eighteen soil indicators. This study shows that the MDS provided a strong representation of the TDS data (R² = 0.81), and the SQI was positively correlated with litter mass (R² = 0.37). An analysis of individual soil indicators in the MDS revealed that phosphorus addition through fertilization (P and NP treatments) significantly enhanced the soil phosphorus pool (64–101%) in the subtropical plantation ecosystem. Long-term fertilization did not significantly change the soil quality, as measured using the SQI, in either the Acacia auriculiformis (p = 0.25) or Eucalyptus urophylla (p = 0.45) plantation, and no significant differences were observed between the two plantation types. These findings suggest that the MDS can serve as a quantitative and effective tool for long-term soil quality monitoring during the process of forest sustainable management. Full article

Insect-derived frass is gaining attention as a circular bioeconomy product with fertilizing and pest-suppressive potential. This study investigates Tenebrio molitor frass as a soil amendment for promoting beneficial nematodes and suppressing Meloidogyne incognita. A 40-day pot experiment on clay loam soil tested with six inputs: raw and heat-treated frass (0.5%, 1% w/w), Melia azedarach fruit powder (1.6%), and an untreated control. Soil nematode communities were assessed at 5 and 40 days after application (DAA), and nematicidal activity was evaluated in vitro. Raw frass at 1% induced a rapid response from free-living nematodes at 5 DAA, with increased abundance of bacterivorous taxa such as Rhabditis and Acrobeloides, alongside a higher Enrichment Index (EI), indicating short-term nutrient availability. At 40 DAA, only 1% raw frass consistently supported more cp-1 bacterivores and slightly increased Shannon diversity. Network analysis revealed more connected, modular structures in raw frass treatments, suggesting enhanced food web complexity. However, omnivore and predator effects were limited. Raw frass extracts caused over 80% paralysis of Meloidogyne incognita juveniles within 24 h, significantly outperforming heat-treated frass and Melia extracts. T. molitor frass moderately stimulates opportunistic nematodes and provides strong nematicidal effects, supporting its potential as a multifunctional input for sustainable soil management. Full article